Flash, FRAM and EEPROM driver for STM32 QUAD-/OCTOSPI interface

- write speed up to 150 kByte/s on STM32F469I-disco (due to
  SWD clock and USB connection), up to 1 MByte/s on Nucleo-F767ZI
  with external STLink-V3 or Nucleo-G474RE with two W25Q256FV in
  dual 4-line mode or STM32H73BI-Disco in octal mode
- tested with STM32L476G-disco (64MBit flash, 3-byte addr),
  STM32F412G-Disco, STM32F469I-Disco, STM32F746G-Disco, and
  STM32L476G-Disco (all 128Mbit flash, 3-byte addr),
  STM32F723E-Disco, STM32F769I-Disco (512Mbit flash, 4-byte addr)
  STM32L4R9I-Disco, STM32L4P5G-Disco (512MBit octo-flash, DTR, 4-byte addr)
  STM32H745I-Disco, STM32H747I-Disco (two 512MBit flash, 4-byte addr)
  STM32H73BI-Disco, STM32H735G-Disco (512MBit octo-flash, DTR, 4-byte addr)
- suitable cfg for Discovery boards included
- limited parsing of SFDP data if flash device not hardcoded
  (tested only in single/quad mode as most devices either don't
  support SFDP at all or have empty(!) SFDP memory)
- 'set' command for auto detection override (e. g. for EEPROMs)
- 'cmd' command for arbitrary SPI commands (reconfiguration, testing etc.)
- makefile for creation of binary loader files
- tcl/board/stm32f469discovery.cfg superseded by stm32f469i-disco.cfg
- tcl/board/stm32f7discovery.cfg removed as name is ambiguous
  (superseded by stm32f746g-disco.cfg vs. stm32f769i-disco.cfg)
- dual 4-line mode tested on Nucleo-F767ZI, Nucleo-H743ZI and Nucleo-H7A3ZI-Q
  with two W25Q256FV, and on Nucleo-L496ZP-P and Nucleo-L4R5ZI
  with two W25Q128FV, sample cfg files included and on STM32H745I-Disco,
  STM32H747I-Disco, STM32H750B-Disco
- read/verify/erase_check uses indirect read mode to work around silicon bug in
  H7, L4+ and MP1 memory mapped mode (last bytes not readable, accessing last
  bytes causes debug interface to hang)
- octospi supported only in single/dual 1-line, 2-line, 4-line
  and single 8-line modes, (not in hyper flash mode)

Requirements:
GPIOs must be initialized appropriately, and SPI flash chip be configured
appropriately (1-line ..., QPI, 4-byte addresses ...). This is board/chip
specific, cf. included cfg files. The driver infers most parameters from
current setting in CR, CCR, ... registers.

Change-Id: I54858fbbe8758c3a5fe58812e93f5f39514704f8
Signed-off-by: Andreas Bolsch <hyphen0break@gmail.com>
Reviewed-on: http://openocd.zylin.com/4321
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Christopher Head <chead@zaber.com>

1 files changed, 74 insertions, 0 deletions

diff --git a/tcl/board/stm32f723e-disco.cfg b/tcl/board/stm32f723e-disco.cfg
new file mode 100644
index 0000000..3c04d86
--- /dev/null
+++ b/tcl/board/stm32f723e-disco.cfg
@@ -0,0 +1,74 @@
+# This is an STM32F723E discovery board with a single STM32F723IEK6 chip.
+# http://www.st.com/en/evaluation-tools/32f723ediscovery.html
+
+# This is for using the onboard STLINK
+source [find interface/stlink.cfg]
+
+transport select hla_swd
+
+# increase working area to 128KB
+set WORKAREASIZE 0x20000
+
+# enable stmqspi
+set QUADSPI 1
+
+source [find target/stm32f7x.cfg]
+
+# QUADSPI initialization
+proc qspi_init { } {
+	global a
+	mmw 0x40023830 0x000007FF 0				;# RCC_AHB1ENR |= GPIOAEN-GPIOKEN (enable clocks)
+	mmw 0x40023838 0x00000002 0				;# RCC_AHB3ENR |= QSPIEN (enable clock)
+	sleep 1									;# Wait for clock startup
+
+	# PB02: CLK, PB06: BK1_NCS, PD13: BK1_IO3, PE02: BK1_IO2, PC10: BK1_IO1, PC09: BK1_IO0
+
+	# PB06:AF10:V, PB02:AF09:V, PC10:AF09:V, PC09:AF09:V, PD13:AF09:V, PE02:AF09:V
+
+	# Port B: PB06:AF10:V, PB02:AF09:V
+	mmw 0x40020400 0x00002020 0x00001010	;# MODER
+	mmw 0x40020408 0x00003030 0x00000000	;# OSPEEDR
+	mmw 0x40020420 0x0A000900 0x05000600	;# AFRL
+
+	# Port C: PC10:AF09:V, PC09:AF09:V
+	mmw 0x40020800 0x00280000 0x00140000	;# MODER
+	mmw 0x40020808 0x003C0000 0x00000000	;# OSPEEDR
+	mmw 0x40020824 0x00000990 0x00000660	;# AFRH
+
+	# Port D: PD13:AF09:V
+	mmw 0x40020C00 0x08000000 0x04000000	;# MODER
+	mmw 0x40020C08 0x0C000000 0x00000000	;# OSPEEDR
+	mmw 0x40020C24 0x00900000 0x00600000	;# AFRH
+
+	# Port E: PE02:AF09:V
+	mmw 0x40021000 0x00000020 0x00000010	;# MODER
+	mmw 0x40021008 0x00000030 0x00000000	;# OSPEEDR
+	mmw 0x40021020 0x00000900 0x00000600	;# AFRL
+
+	mww 0xA0001030 0x00001000				;# QUADSPI_LPTR: deactivate CS after 4096 clocks when FIFO is full
+	mww 0xA0001000 0x03500008				;# QUADSPI_CR: PRESCALER=3, APMS=1, FTHRES=0, FSEL=0, DFM=0, SSHIFT=0, TCEN=1
+	mww 0xA0001004 0x00190100				;# QUADSPI_DCR: FSIZE=0x19, CSHT=0x01, CKMODE=0
+	mmw 0xA0001000 0x00000001 0				;# QUADSPI_CR: EN=1
+
+	# 1-line spi mode
+	mww 0xA0001014 0x000003F5				;# QUADSPI_CCR: FMODE=0x0, DMODE=0x0, DCYC=0x0, ADSIZE=0x0, ADMODE=0x0, IMODE=0x3, INSTR=RSTQIO
+	sleep 1
+
+	# memory-mapped read mode with 4-byte addresses
+	mww 0xA0001014 0x0D003513				;# QUADSPI_CCR: FMODE=0x3, DMODE=0x1, DCYC=0x0, ADSIZE=0x3, ADMODE=0x1, IMODE=0x1, INSTR=READ
+}
+
+$_TARGETNAME configure -event reset-init {
+	mww 0x40023C00 0x00000006				;# 6 WS for 192 MHz HCLK
+	sleep 1
+	mww 0x40023804 0x24003008				;# 192 MHz: PLLM=8, PLLN=192, PLLP=2
+	mww 0x40023808 0x00009400				;# APB1: /4, APB2: /2
+	mmw 0x40023800 0x01000000 0x00000000	;# PLL on
+	sleep 1
+	mmw 0x40023808 0x00000002 0x00000000	;# switch to PLL
+	sleep 1
+
+	adapter speed 4000
+
+	qspi_init
+}