1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
|
# SPDX-License-Identifier: GPL-2.0-or-later
# Main file for NXP LPC1xxx/LPC40xx series Cortex-M0/0+/3/4F parts
#
# !!!!!!
#
# This file should not be included directly, rather by the lpc11xx.cfg,
# lpc13xx.cfg, lpc17xx.cfg, etc. which set the needed variables to the
# appropriate values.
#
# !!!!!!
# LPC8xx chips support only SWD transport.
# LPC11xx chips support only SWD transport.
# LPC12xx chips support only SWD transport.
# LPC11Uxx chips support only SWD transports.
# LPC13xx chips support only SWD transports.
# LPC17xx chips support both JTAG and SWD transports.
# LPC40xx chips support both JTAG and SWD transports.
# Adapt based on what transport is active.
source [find target/swj-dp.tcl]
if { [info exists CHIPNAME] } {
set _CHIPNAME $CHIPNAME
} else {
error "CHIPNAME not set. Please do not include lpc1xxx.cfg directly, but the specific chip configuration file (lpc11xx.cfg, lpc13xx.cfg, lpc17xx.cfg, etc)."
}
if { [info exists CHIPSERIES] } {
# Validate chip series is supported
if { $CHIPSERIES != "lpc800" && $CHIPSERIES != "lpc1100" && $CHIPSERIES != "lpc1200" && $CHIPSERIES != "lpc1300" && $CHIPSERIES != "lpc1700" && $CHIPSERIES != "lpc4000" } {
error "Unsupported LPC1xxx chip series specified."
}
set _CHIPSERIES $CHIPSERIES
} else {
error "CHIPSERIES not set. Please do not include lpc1xxx.cfg directly, but the specific chip configuration file (lpc11xx.cfg, lpc13xx.cfg, lpc17xx.cfg, etc)."
}
# After reset, the chip is clocked by an internal RC oscillator.
# When board-specific code (reset-init handler or device firmware)
# configures another oscillator and/or PLL0, set CCLK to match; if
# you don't, then flash erase and write operations may misbehave.
# (The ROM code doing those updates cares about core clock speed...)
# CCLK is the core clock frequency in KHz
if { [info exists CCLK] } {
# Allow user override
set _CCLK $CCLK
} else {
# LPC8xx/LPC11xx/LPC12xx/LPC13xx use a 12MHz one, LPC17xx uses a 4MHz one(except for LPC177x/8x,LPC407x/8x)
if { $_CHIPSERIES == "lpc800" || $_CHIPSERIES == "lpc1100" || $_CHIPSERIES == "lpc1200" || $_CHIPSERIES == "lpc1300" } {
set _CCLK 12000
} elseif { $_CHIPSERIES == "lpc1700" || $_CHIPSERIES == "lpc4000" } {
set _CCLK 4000
}
}
if { [info exists CPUTAPID] } {
# Allow user override
set _CPUTAPID $CPUTAPID
} else {
# LPC8xx/LPC11xx/LPC12xx use a Cortex-M0/M0+ core, LPC13xx/LPC17xx use a Cortex-M3 core, LPC40xx use a Cortex-M4F core.
if { $_CHIPSERIES == "lpc800" || $_CHIPSERIES == "lpc1100" || $_CHIPSERIES == "lpc1200" } {
set _CPUTAPID 0x0bb11477
} elseif { $_CHIPSERIES == "lpc1300" || $_CHIPSERIES == "lpc1700" || $_CHIPSERIES == "lpc4000" } {
if { [using_jtag] } {
set _CPUTAPID 0x4ba00477
} {
set _CPUTAPID 0x2ba01477
}
}
}
if { [info exists WORKAREASIZE] } {
set _WORKAREASIZE $WORKAREASIZE
} else {
error "WORKAREASIZE is not set. The $CHIPNAME part is available in several Flash and RAM size configurations. Please set WORKAREASIZE."
}
swj_newdap $_CHIPNAME cpu -irlen 4 -expected-id $_CPUTAPID
dap create $_CHIPNAME.dap -chain-position $_CHIPNAME.cpu
set _TARGETNAME $_CHIPNAME.cpu
target create $_TARGETNAME cortex_m -dap $_CHIPNAME.dap
# The LPC11xx devices have 2/4/8kB of SRAM in the ARMv7-M "Code" area (at 0x10000000)
# The LPC12xx devices have 4/8kB of SRAM in the ARMv7-M "Code" area (at 0x10000000)
# The LPC11Uxx devices have 4/6/8kB of SRAM in the ARMv7-M "Code" area (at 0x10000000)
# The LPC13xx devices have 4/8kB of SRAM in the ARMv7-M "Code" area (at 0x10000000)
# The LPC17xx devices have 8/16/32/64kB of SRAM in the ARMv7-M "Code" area (at 0x10000000)
# The LPC40xx devices have 16/32/64kB of SRAM in the ARMv7-ME "Code" area (at 0x10000000)
$_TARGETNAME configure -work-area-phys 0x10000000 -work-area-size $_WORKAREASIZE
# The LPC11xx devies have 8/16/24/32/48/56/64kB of flash memory (at 0x00000000)
# The LPC12xx devies have 32/48/64/80/96/128kB of flash memory (at 0x00000000)
# The LPC11Uxx devies have 16/24/32/40/48/64/96/128kB of flash memory (at 0x00000000)
# The LPC13xx devies have 8/16/32kB of flash memory (at 0x00000000)
# The LPC17xx devies have 32/64/128/256/512kB of flash memory (at 0x00000000)
# The LPC40xx devies have 64/128/256/512kB of flash memory (at 0x00000000)
#
# All are compatible with the "lpc1700" variant of the LPC2000 flash driver
# (same cmd51 destination boundary alignment, and all three support 256 byte
# transfers).
#
# flash bank <name> lpc2000 <base> <size> 0 0 <target#> <variant> <clock> [calc checksum] [iap entry]
set _IAP_ENTRY 0
if { [info exists IAP_ENTRY] } {
set _IAP_ENTRY $IAP_ENTRY
}
set _FLASHNAME $_CHIPNAME.flash
flash bank $_FLASHNAME lpc2000 0x0 0 0 0 $_TARGETNAME \
auto $_CCLK calc_checksum $_IAP_ENTRY
if { $_CHIPSERIES == "lpc800" || $_CHIPSERIES == "lpc1100" || $_CHIPSERIES == "lpc1200" || $_CHIPSERIES == "lpc1300" } {
# Do not remap 0x0000-0x0200 to anything but the flash (i.e. select
# "User Flash Mode" where interrupt vectors are _not_ remapped,
# and reside in flash instead).
#
# Table 8. System memory remap register (SYSMEMREMAP, address 0x4004 8000) bit description
# Bit Symbol Value Description
# 1:0 MAP System memory remap
# 0x0 Boot Loader Mode. Interrupt vectors are re-mapped to Boot ROM.
# 0x1 User RAM Mode. Interrupt vectors are re-mapped to Static RAM.
# 0x2 User Flash Mode. Interrupt vectors are not re-mapped and reside in Flash.
# 31:2 - - Reserved.
$_TARGETNAME configure -event reset-init {
mww 0x40048000 0x02
}
} elseif { $_CHIPSERIES == "lpc1700" || $_CHIPSERIES == "lpc4000" } {
# Do not remap 0x0000-0x0020 to anything but the flash (i.e. select
# "User Flash Mode" where interrupt vectors are _not_ remapped,
# and reside in flash instead).
#
# See Table 612. Memory Mapping Control register (MEMMAP - 0x400F C040) bit description
# Bit Symbol Value Description Reset
# value
# 0 MAP Memory map control. 0
# 0 Boot mode. A portion of the Boot ROM is mapped to address 0.
# 1 User mode. The on-chip Flash memory is mapped to address 0.
# 31:1 - Reserved. The value read from a reserved bit is not defined. NA
#
# http://ics.nxp.com/support/documents/microcontrollers/?scope=LPC1768&type=user
$_TARGETNAME configure -event reset-init {
mww 0x400FC040 0x01
}
}
# Run with *real slow* clock by default since the
# boot rom could have been playing with the PLL, so
# we have no idea what clock the target is running at.
adapter speed 10
# delays on reset lines
adapter srst delay 200
if {[using_jtag]} {
jtag_ntrst_delay 200
}
# LPC8xx (Cortex-M0+ core) support SYSRESETREQ
# LPC11xx/LPC12xx (Cortex-M0 core) support SYSRESETREQ
# LPC13xx/LPC17xx (Cortex-M3 core) support SYSRESETREQ
# LPC40xx (Cortex-M4F core) support SYSRESETREQ
if {![using_hla]} {
# if srst is not fitted use SYSRESETREQ to
# perform a soft reset
cortex_m reset_config sysresetreq
}
|
