1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
|
# DM355 EVM board
# http://focus.ti.com/docs/toolsw/folders/print/tmdsevm355.html
# http://c6000.spectrumdigital.com/evmdm355/
source [find target/ti_dm355.cfg]
reset_config trst_and_srst separate
# NOTE: disable or replace this call to dm355evm_init if you're
# debugging new UBL code from SRAM.
$_TARGETNAME configure -event reset-init { dm355evm_init }
#
# This post-reset init is called when the MMU isn't active, all IRQs
# are disabled, etc. It should do most of what a UBL does, except for
# loading code (like U-Boot) into DRAM and running it.
#
proc dm355evm_init {} {
global dm355
puts "Initialize DM355 EVM board"
# CLKIN = 24 MHz ... can't talk quickly to ARM yet
jtag_rclk 1500
########################
# PLL1 = 432 MHz (/8, x144)
# ...SYSCLK1 = 216 MHz (/2) ... ARM, MJCP
# ...SYSCLK2 = 108 MHz (/4) ... Peripherals
# ...SYSCLK3 = 27 MHz (/16) ... VPBE, DAC
# ...SYSCLK4 = 108 MHz (/4) ... VPSS
# pll1.{prediv,div1,div2} are fixed
# pll1.postdiv set in MISC (for *this* speed grade)
set addr [dict get $dm355 pllc1]
set pll_divs [dict create]
dict set pll_divs div3 16
dict set pll_divs div4 8
pll_v02_setup $addr 144 $pll_divs
# ARM is now running at 216 MHz, so JTAG can go faster
jtag_rclk 20000
########################
# PLL2 = 342 MHz (/8, x114)
# ....SYSCLK1 = 342 MHz (/1) ... DDR PHY at 171 MHz, 2x clock
# pll2.{postdiv,div1} are fixed
set addr [dict get $dm355 pllc2]
set pll_divs [dict create]
dict set pll_divs prediv 8
pll_v02_setup $addr 114 $pll_divs
########################
# PINMUX
# All Video Inputs
davinci_pinmux $dm355 0 0x00007f55
# All Video Outputs
davinci_pinmux $dm355 1 0x00145555
# EMIFA (NOTE: more could be set up for use as GPIOs)
davinci_pinmux $dm355 2 0x00000c08
# SPI0, SPI1, UART1, I2C, SD0, SD1, McBSP0, CLKOUTs
davinci_pinmux $dm355 3 0x1bff55ff
# MMC/SD0 instead of MS; SPI0
davinci_pinmux $dm355 4 0x00000000
########################
# PSC setup (minimal)
# DDR EMIF/13, AEMIF/14, UART0/19
psc_enable 13
psc_enable 14
psc_enable 19
psc_go
########################
# DDR2 EMIF
# FIXME setup
########################
# ASYNC EMIF
set addr [dict get $dm355 a_emif]
# slow/pessimistic timings
set nand_timings 0x40400204
# fast (25% faster page reads)
#set nand_timings 0x0400008c
# AWCCR
mww [expr $addr + 0x04] 0xff
# CS0 == socketed NAND (default MT29F16G08FAA, 2GByte)
mww [expr $addr + 0x10] $nand_timings
# CS1 == dm9000 Ethernet
mww [expr $addr + 0x14] 0x00a00505
# NANDFCR -- only CS0 has NAND
mww [expr $addr + 0x60] 0x01
########################
# UART0
# FIXME setup
}
# NAND -- socket has two chipselects, MT29F16G08FAA puts 1GByte on each one.
#
# NOTE: "hwecc4" here presumes that if you're using the standard 2GB NAND
# you either (a) have 'new' DM355 chips, with boot ROMs that don't need to
# use "hwecc4_infix" for the UBL; or else (b) aren't updating anything that
# needs infix layout ... like an old UBL, old U-Boot, old MVL kernel, etc.
nand device davinci 0 0x02000000 hwecc4 0x01e10000
nand device davinci 0 0x02004000 hwecc4 0x01e10000
# FIXME
# - support writing UBL with its header (new layout only with new ROMs)
# - support writing ABL/U-Boot with its header (new layout)
|
