aboutsummaryrefslogtreecommitdiff
path: root/tcl/board
AgeCommit message (Collapse)AuthorFilesLines
2009-12-01target: at91eb40a.cfg is a board, not a target.Øyvind Harboe1-0/+65
Also updated to use target name when creating flash and set jtag_khz to 16000. Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
2009-11-23arm926ejs: fix gaffe when converting from arm926ejs cp15 to mcrØyvind Harboe3-3/+3
the first arg is the register number 15 = cp15. Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
2009-11-23arm926ejs: retire cp15 commands, handled by mrc/mcr.Øyvind Harboe3-3/+3
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
2009-11-19update 'nand device' usage in scriptsZachary T Welch3-4/+8
Add $_FLASHNAME variable to update 'nand device' command syntax.
2009-11-19update 'flash bank' usage in scriptsZachary T Welch18-23/+46
Sets $_FLASHNAME to "$_CHIPNAME.flash" and passes it as the first argument to 'flash bank'.
2009-11-16ARM: "armv4_5" command prefix becomes "arm"David Brownell1-1/+1
Rename the "armv4_5" command prefix to straight "arm" so it makes more sense for newer cores. Add a simple compatibility script. Make sure all the commands give the same "not an ARM" diagnostic message (and fail properly) when called against non-ARM targets. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
2009-11-10target.cfg: (re)move some bogus reset_config linesDavid Brownell1-0/+3
General rule, this is all board-specific and doesn't belong in target config files. Some of these were just cosmetic. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
2009-11-10ARM11: remove old mrc/mcr commandsØyvind Harboe1-3/+3
Switch to new commands in config scripts Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
2009-11-10telo.cfg: fix search pathsØyvind Harboe1-4/+4
Add the missing "target/" prefix for scripts in the target folder. Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
2009-11-09finish removing deprecated/obsolete commandsDavid Brownell2-2/+2
It's been about a year since these were deprecated and, in most cases, removed. There's no point in carrying that documentation, or backwards compatibility for "jtag_device" and "jtag_speed", around forever. (Or a few remnants of obsolete code...) Removed a few obsolete uses of "jtag_speed": - The Calao stuff hasn't worked since July 2008. (Those Atmel targets need to work with a 32KHz core clock after reset until board-specific init-reset code sets up the PLL and enables a faster JTAg clock.) - Parport speed controls don't actually work (tops out at about 1 MHz on typical HW). - In general, speed controls need to live in board.cfg files (or sometimes target.cfg files), not interface.cfg ... Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
2009-11-08target.cfg: remove "-work-area-virt 0"David Brownell8-9/+9
The semantics of "-work-area-virt 0" (or phys) changed with the patch to require specifying physical or virtrual work area addresses. Specifying zero was previously a NOP. Now it means that address zero is valid. This patch addresses three related issues: - MMU-less processors should never specify work-area-virt; remove those specifications. Such processors include ARM7TDMI, Cortex-M3, and ARM966. - MMU-equipped processors *can* specify work-area-virt... but zero won't be appropriate, except in mischievous contexts (which hide null pointer exceptions). Remove those specs from those processors too. If any of those mappings is valid, someone will need to submit a patch adding it ... along with a comment saying what OS provides the mapping, and in which context. Example, say "works with Linux 2.6.30+, in kernel mode". (Note that ARM Linux doesn't map kernel memory to zero ...) - Clarify docs on that "-virt" and other work area stuff. Seems to me work-area-virt is quite problematic; not every operating system provides such static mappings; if they do, they're not in every MMU context... Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
2009-11-04PXA255: support Intel "Lubbock" platformDavid Brownell1-0/+110
Config for Intel's "Lubbock" PXA255 development board. Even more so than the PXA255 itself, this is obsolete. AFAIK this was the first generally available development platform for PXA255. Intel stopped providing these after other devel boards became available. One interesting thing about this board from the OpenOCD perspective is probably its flash configuration. Each bank is 32 bits wide, built from two 16-bit StrataFlash chips wired in parallel. This doubles throughput ... it reads/writes 32 bits in the time a single chip takes to write just 16 bits. This conf mostly works, given XScale bugfixes, but has some issues (notably: no access to the on-board SDRAM) flagged by FIXMEs. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
2009-10-26balloon3 board base configWookey1-0/+13
This is the very basic board config for the balloon3 board cpu JTAG channel. The rest of the config comprises another 14 .cfg files which I suspect openocd doesn't really want all of. I'm still not sure how to deal with this. I'll post another mail/patch to discuss. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
2009-10-25fix syntax of mww phys.Øyvind Harboe4-33/+33
2009-10-21mww_phys retired. Replaced by generic mww phys in target.cØyvind Harboe4-33/+33
2009-10-18SDRAM and clock configuration for the SAM9-L9260 board from OlimexDean Glazeski1-6/+85
2009-10-14Fw: [PATCH] OpenRD board configurationWookey1-0/+122
Ofrwarded from Ron, who's not subscribed. ----- Forwarded message from Ron <ron@debian.org> ----- From: Ron <ron@debian.org> Date: Wed, 14 Oct 2009 04:50:17 +1030 To: wookey@debian.org Subject: [PATCH] OpenRD board configuration X-Spam-Status: No, score=-3.6 required=4.5 tests=BAYES_00,RCVD_IN_DNSWL_LOW autolearn=ham version=3.2.5 This piggybacks on the 'sheevaplug' layout which uses the same Kirkwood SoC. Signed-off-by: Ron Lee <ron@debian.org>
2009-10-14iMX target config script's ported from Freescale BSP.Øyvind Harboe2-65/+27
2009-10-12burst writes work fine. clean up junk.Øyvind Harboe1-3/+0
2009-10-09Added tip in documentation on how to translate quirky syntaxØyvind Harboe1-0/+3
2009-10-08Function to flash SheevaPlug u-boot sectorsRabeeh Khoury1-0/+11
This function is used by the SheevaPlug installer to flash the erase and re-flash the U-Boot environment in the NAND Flash.
2009-10-08initial builds of OSK5912 boards need srst_pulls_trstDavid Brownell1-0/+4
This is clearly noted in the hardware spec (section 5.2.3); it works around a chip erratum: "If the MPU_RESET signal is used, it may cause the EMIFS bus to lock." I seem to have a board with such an initial build. The chip is labeled XOMAP. Presumably, parts without that "X" prefix (eXperimental) resolve this. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
2009-10-07first stab at imx35 reset init scriptoharboe1-0/+272
git-svn-id: svn://svn.berlios.de/openocd/trunk@2817 b42882b7-edfa-0310-969c-e2dbd0fdcd60
2009-10-07remove recrusive reset invocation from reset init callbackoharboe1-5/+0
git-svn-id: svn://svn.berlios.de/openocd/trunk@2816 b42882b7-edfa-0310-969c-e2dbd0fdcd60
2009-10-06Add basic support for DM6446 EVM board.dbrownell1-0/+74
git-svn-id: svn://svn.berlios.de/openocd/trunk@2808 b42882b7-edfa-0310-969c-e2dbd0fdcd60
2009-10-06stop using targetnumoharboe1-1/+1
git-svn-id: svn://svn.berlios.de/openocd/trunk@2804 b42882b7-edfa-0310-969c-e2dbd0fdcd60
2009-09-30Remove annoying EOL whitespace (again, sigh).dbrownell3-7/+7
git-svn-id: svn://svn.berlios.de/openocd/trunk@2781 b42882b7-edfa-0310-969c-e2dbd0fdcd60
2009-09-30strip gdb config optionsoharboe1-4/+0
git-svn-id: svn://svn.berlios.de/openocd/trunk@2779 b42882b7-edfa-0310-969c-e2dbd0fdcd60
2009-09-30michal smulski <michal.smulski@ooma.com> reset now worksoharboe1-17/+23
git-svn-id: svn://svn.berlios.de/openocd/trunk@2778 b42882b7-edfa-0310-969c-e2dbd0fdcd60
2009-09-26On DM355 EVM board, associate NAND chips with $_TARGETNAMEdbrownell1-2/+2
instead of a target number. git-svn-id: svn://svn.berlios.de/openocd/trunk@2761 b42882b7-edfa-0310-969c-e2dbd0fdcd60
2009-09-25Michael Hasselberg <mh@open-engineering.de> target configuration files for ↵oharboe2-0/+243
Toshiba TX09 familiy git-svn-id: svn://svn.berlios.de/openocd/trunk@2756 b42882b7-edfa-0310-969c-e2dbd0fdcd60
2009-09-21Remove annoying end-of-line whitespace from tcl/* filesdbrownell21-194/+194
git-svn-id: svn://svn.berlios.de/openocd/trunk@2743 b42882b7-edfa-0310-969c-e2dbd0fdcd60
2009-09-21Ethan Eade <ethan@evolution.com> board config script for Cogent CSB732 ↵oharboe1-0/+71
i.MX35 (arm1136) git-svn-id: svn://svn.berlios.de/openocd/trunk@2741 b42882b7-edfa-0310-969c-e2dbd0fdcd60
2009-09-16Rolf Meeser <rolfm_9dq@yahoo.de> adds flash support for NXP's LPC2900 family ↵oharboe1-0/+105
(ARM968E). git-svn-id: svn://svn.berlios.de/openocd/trunk@2715 b42882b7-edfa-0310-969c-e2dbd0fdcd60
2009-09-12David Brownell <david-b@pacbell.net> oharboe1-3/+84
Update the board config for the DaVinci DM355 EVM so the reset-init event handler does the rest of the work it should do: - minor PLL setup bugfixes - initialize the DDR2 controller - probe both NAND banks - initialize UART0 - enable the icache git-svn-id: svn://svn.berlios.de/openocd/trunk@2699 b42882b7-edfa-0310-969c-e2dbd0fdcd60
2009-09-10michal smulski <michal.smulski@ooma.com> telo target/board scriptsoharboe1-0/+54
git-svn-id: svn://svn.berlios.de/openocd/trunk@2683 b42882b7-edfa-0310-969c-e2dbd0fdcd60
2009-09-04Dirk Behme <dirk.behme@googlemail.com> Add default fall back freqency.oharboe1-0/+3
git-svn-id: svn://svn.berlios.de/openocd/trunk@2670 b42882b7-edfa-0310-969c-e2dbd0fdcd60
2009-08-31Gary Carlson <gcarlson@carlson-minot.com> config fileoharboe1-0/+204
git-svn-id: svn://svn.berlios.de/openocd/trunk@2657 b42882b7-edfa-0310-969c-e2dbd0fdcd60
2009-08-31Ferdinand Postema <ferdinand@postema.eu> config script for the MMnet1001 ↵oharboe1-0/+83
module from Propox. git-svn-id: svn://svn.berlios.de/openocd/trunk@2656 b42882b7-edfa-0310-969c-e2dbd0fdcd60
2009-08-28David Brownell <david-b@pacbell.net> The Stellaris eval boards don't have ↵oharboe4-6/+0
TRST signals, so defining ntrst_delay is pointless; don't. At least the LM3S3748 eval board doesn't need nsrst_delay either; remove that too. git-svn-id: svn://svn.berlios.de/openocd/trunk@2645 b42882b7-edfa-0310-969c-e2dbd0fdcd60
2009-08-25Brian Findlay <findlaybrian@gmail.com> finalize mini2440.cfgoharboe1-3/+2
git-svn-id: svn://svn.berlios.de/openocd/trunk@2611 b42882b7-edfa-0310-969c-e2dbd0fdcd60
2009-08-21Pieter Conradie <Pieter.Conradie@psitek.com> shuffle things around to the ↵oharboe3-181/+0
right spots. Should have been done in previous commit. git-svn-id: svn://svn.berlios.de/openocd/trunk@2604 b42882b7-edfa-0310-969c-e2dbd0fdcd60
2009-08-21native line endingsoharboe5-284/+284
git-svn-id: svn://svn.berlios.de/openocd/trunk@2603 b42882b7-edfa-0310-969c-e2dbd0fdcd60
2009-08-21Pieter Conradie <Pieter.Conradie@psitek.com> Scripts for Atmel AT91SAM7S256 ↵oharboe5-0/+284
and AT91SAM9260 git-svn-id: svn://svn.berlios.de/openocd/trunk@2602 b42882b7-edfa-0310-969c-e2dbd0fdcd60
2009-08-18Brian Findlay <findlaybrian@gmail.com> Board support for mini2440 ↵oharboe1-0/+321
(friendlyARM) samsung s3c2440 based board git-svn-id: svn://svn.berlios.de/openocd/trunk@2593 b42882b7-edfa-0310-969c-e2dbd0fdcd60
2009-08-16Xiaofan Chen <xiaofanc@gmail.com> Split LM3S811 config file into target file ↵oharboe1-0/+19
and board file git-svn-id: svn://svn.berlios.de/openocd/trunk@2584 b42882b7-edfa-0310-969c-e2dbd0fdcd60
2009-08-16Xiaofan Chen <xiaofanc@gmail.com> Add config file for TI-Luminary LM3S1968 ↵oharboe1-0/+23
chip and EK-LM3S1968 board git-svn-id: svn://svn.berlios.de/openocd/trunk@2582 b42882b7-edfa-0310-969c-e2dbd0fdcd60
2009-08-13Audrius Urmanavičius [didele.deze@gmail.com]:ntfreak1-0/+8
Add flash programming support for NXP LPC1700 cortex_m3 based family git-svn-id: svn://svn.berlios.de/openocd/trunk@2579 b42882b7-edfa-0310-969c-e2dbd0fdcd60
2009-07-22Jonathan Cameron <jic23@cam.ac.uk> fix regression from 1836 when the ↵oharboe1-0/+2
reset_config command was removed from pxa270.cfg git-svn-id: svn://svn.berlios.de/openocd/trunk@2557 b42882b7-edfa-0310-969c-e2dbd0fdcd60
2009-07-10David Brownell <david-b@pacbell.net> split EK board support outoharboe1-0/+17
from the target CPU support . git-svn-id: svn://svn.berlios.de/openocd/trunk@2504 b42882b7-edfa-0310-969c-e2dbd0fdcd60
generated by cgit v1.1 at 2024-11-06 15:38:56 +0000