diff options
Diffstat (limited to 'tcl')
| -rw-r--r-- | tcl/target/davinci.cfg | 63 |
1 files changed, 62 insertions, 1 deletions
diff --git a/tcl/target/davinci.cfg b/tcl/target/davinci.cfg index 658e7fe..e1eb48f 100644 --- a/tcl/target/davinci.cfg +++ b/tcl/target/davinci.cfg @@ -33,7 +33,7 @@ proc mmw {reg setbits clearbits} { # # PLL version 0x02: tested on dm355 -# REVISIT: On dm6446 and dm357 the PLLRST polarity is different. +# REVISIT: On dm6446/dm357 the PLLRST polarity is different. proc pll_v02_setup {pll_addr mult config} { set pll_ctrl_addr [expr $pll_addr + 0x100] set pll_ctrl [mrw $pll_ctrl_addr] @@ -174,3 +174,64 @@ proc psc_go {} { # wait for PTSTAT.go to clear (again ignoring DSP power domain) while { [expr [mrw $ptstat_addr] & 0x01] != 0 } { sleep 1 } } + +# +# A reset using only SRST is a "Warm Reset", resetting everything in the +# chip except ARM emulation (and everything _outside_ the chip that hooks +# up to SRST). But many boards don't expose SRST via their JTAG connectors +# (it's not present on TI-14 headers). +# +# From the chip-only perspective, a "Max Reset" is a "Warm" reset ... except +# without any board-wide side effects, since it's triggered using JTAG using +# either (a) ARM watchdog timer, or (b) ICEpick. +# +proc davinci_wdog_reset {} { + set timer2_phys 0x01c21c00 + + # NOTE -- on entry + # - JTAG communication with the ARM *must* be working OK; this + # may imply using adaptive clocking or disabling WFI-in-idle + # - current target must be the DaVinci ARM + # - that ARM core must be halted + # - timer2 clock is still enabled (PSC 29 on most chips) + + # + # Part I -- run regardless of being halted via JTAG + # + # NOTE: for now, we assume there's no DSP that could control the + # watchdog; or, equivalently, SUSPSRC.TMR2SRC says the watchdog + # suspend signal is controlled via ARM emulation suspend. + # + + # EMUMGT_CLKSPEED: write FREE bit to run despite emulation halt + arm926ejs mww_phys [expr $timer2_phys + 0x28] 0x00004000 + + # + # Part II -- in case watchdog hasn't been set up + # + + # TCR: disable, force internal clock source + arm926ejs mww_phys [expr $timer2_phys + 0x20] 0 + + # TGCR: reset, force to 64-bit wdog mode, un-reset ("initial" state) + arm926ejs mww_phys [expr $timer2_phys + 0x24] 0 + arm926ejs mww_phys [expr $timer2_phys + 0x24] 0x110b + + # clear counter (TIM12, TIM34) and period (PRD12, PRD34) registers + # so watchdog triggers ASAP + arm926ejs mww_phys [expr $timer2_phys + 0x10] 0 + arm926ejs mww_phys [expr $timer2_phys + 0x14] 0 + arm926ejs mww_phys [expr $timer2_phys + 0x18] 0 + arm926ejs mww_phys [expr $timer2_phys + 0x1c] 0 + + # WDTCR: put into pre-active state, then active + arm926ejs mww_phys [expr $timer2_phys + 0x28] 0xa5c64000 + arm926ejs mww_phys [expr $timer2_phys + 0x28] 0xda7e4000 + + # + # Part III -- it's ready to rumble + # + + # WDTCR: write invalid WDKEY to trigger reset + arm926ejs mww_phys [expr $timer2_phys + 0x28] 0x00004000 +} |