aboutsummaryrefslogtreecommitdiff
path: root/tcl/board
diff options
context:
space:
mode:
Diffstat (limited to 'tcl/board')
-rw-r--r--tcl/board/arm_evaluator7t.cfg2
-rw-r--r--tcl/board/at91sam9g20-ek.cfg2
-rw-r--r--tcl/board/digilent_atlys.cfg2
-rw-r--r--tcl/board/hitex_lpc2929.cfg2
-rw-r--r--tcl/board/mini2440.cfg2
-rw-r--r--tcl/board/uptech_2410.cfg2
6 files changed, 6 insertions, 6 deletions
diff --git a/tcl/board/arm_evaluator7t.cfg b/tcl/board/arm_evaluator7t.cfg
index 96d859c..ef4b782 100644
--- a/tcl/board/arm_evaluator7t.cfg
+++ b/tcl/board/arm_evaluator7t.cfg
@@ -5,5 +5,5 @@ source [find target/samsung_s3c4510.cfg]
#
# FIXME:
# Add (A) sdram configuration
-# Add (B) flash cfi programing configuration
+# Add (B) flash cfi programming configuration
#
diff --git a/tcl/board/at91sam9g20-ek.cfg b/tcl/board/at91sam9g20-ek.cfg
index 59ee4d2..e1cbb91 100644
--- a/tcl/board/at91sam9g20-ek.cfg
+++ b/tcl/board/at91sam9g20-ek.cfg
@@ -153,7 +153,7 @@ proc at91sam9g20_reset_init { } {
nand probe nandflash_cs3
- # The AT91SAM9G20-EK evaluation board has build-in serial data flash also.
+ # The AT91SAM9G20-EK evaluation board has built-in serial data flash also.
# Now setup SDRAM. This is tricky and configuration is very important for reliability! The current calculations
# are based on 2 x Micron MT48LC16M16A2-75 memory (4 M x 16 bit x 4 banks). If you use this file as a reference
diff --git a/tcl/board/digilent_atlys.cfg b/tcl/board/digilent_atlys.cfg
index f298e3d..3eb6219 100644
--- a/tcl/board/digilent_atlys.cfg
+++ b/tcl/board/digilent_atlys.cfg
@@ -5,7 +5,7 @@
# ID 1443:0007 Digilent Development board JTAG
#
# However, the ixo-usb-jtag project provides an alternative open firmware for
-# the on board programmer. When using thie firmware the board will then
+# the on board programmer. When using this firmware the board will then
# enumerate as:
# ID 16c0:06ad Van Ooijen Technische Informatica
# (With SerialNumber == hw_nexys)
diff --git a/tcl/board/hitex_lpc2929.cfg b/tcl/board/hitex_lpc2929.cfg
index 2fe1f3c..8268306 100644
--- a/tcl/board/hitex_lpc2929.cfg
+++ b/tcl/board/hitex_lpc2929.cfg
@@ -34,7 +34,7 @@ flash bank $_FLASHNAME cfi 0x5C000000 0x400000 2 2 $_TARGETNAME jedec_probe
$_TARGETNAME configure -event reset-init {
# Flash
- mww 0x20200010 0x00000007 ;# FBWST: 7 wait states, not chached
+ mww 0x20200010 0x00000007 ;# FBWST: 7 wait states, not cached
# Use PLL
mww 0xFFFF8020 0x00000001 ;# XTAL_OSC_CONTROL: enable, 1-20 MHz
diff --git a/tcl/board/mini2440.cfg b/tcl/board/mini2440.cfg
index 9dca5a3..3d01b38 100644
--- a/tcl/board/mini2440.cfg
+++ b/tcl/board/mini2440.cfg
@@ -38,7 +38,7 @@
# it's apt-get install libusb-dev. When I made my config I only included
# --enable-jlink and --enable-usbdevs
#
-# I HAVE NOT Tested this throughly, so there could still be problems.
+# I HAVE NOT Tested this thoroughly, so there could still be problems.
# But it should get you way ahead of the game from where I started.
# If you find problems (and fixes) please post them to
# openocd-development@lists.berlios.de and join the developers and
diff --git a/tcl/board/uptech_2410.cfg b/tcl/board/uptech_2410.cfg
index 227cf42..0a2c475 100644
--- a/tcl/board/uptech_2410.cfg
+++ b/tcl/board/uptech_2410.cfg
@@ -1,5 +1,5 @@
# Target Configuration for the Uptech 2410 board.
-# This configuration hould also work on smdk2410, but I havn't tested it yet.
+# This configuration should also work on smdk2410, but I haven't tested it yet.
# Author: xionglingfeng@Gmail.com
source [find target/samsung_s3c2410.cfg]