diff options
-rw-r--r-- | tcl/ti-beaglebone.cfg | 92 |
1 files changed, 92 insertions, 0 deletions
diff --git a/tcl/ti-beaglebone.cfg b/tcl/ti-beaglebone.cfg new file mode 100644 index 0000000..c9a54b0 --- /dev/null +++ b/tcl/ti-beaglebone.cfg @@ -0,0 +1,92 @@ +interface ft2232 +#ft2232_device_desc "BeagleBone A" +ft2232_layout xds100v2 +ft2232_vid_pid 0x0403 0xa6d0 + +#jtag_rclk 10 +adapter_khz 1000 + +if { [info exists CHIPNAME] } { + set _CHIPNAME $CHIPNAME +} else { + set _CHIPNAME am335x +} + +proc icepick_d_tapenable {jrc port} { + # select router + irscan $jrc 7 -endstate IRPAUSE + drscan $jrc 8 0x89 -endstate DRPAUSE + + # set ip control + irscan $jrc 2 -endstate IRPAUSE + drscan $jrc 32 [expr 0xa0002108 + ($port << 24)] -endstate DRPAUSE + + # for icepick_D + irscan $jrc 2 -endstate IRPAUSE + drscan $jrc 32 0xe0002008 -endstate DRPAUSE + + irscan $jrc 0x3F -endstate RUN/IDLE + runtest 10 +} + +# +# M3 DAP +# +if { [info exists M3_DAP_TAPID] } { + set _M3_DAP_TAPID $M3_DAP_TAPID +} else { + set _M3_DAP_TAPID 0x4b6b902f +} +jtag newtap $_CHIPNAME m3_dap -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_M3_DAP_TAPID -disable +jtag configure $_CHIPNAME.m3_dap -event tap-enable "icepick_d_tapenable $_CHIPNAME.jrc 11" + +# +# Main DAP +# +if { [info exists DAP_TAPID ] } { + set _DAP_TAPID $DAP_TAPID +} else { + set _DAP_TAPID 0x4b6b902f +} +jtag newtap $_CHIPNAME dap -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_DAP_TAPID -disable +jtag configure $_CHIPNAME.dap -event tap-enable "icepick_d_tapenable $_CHIPNAME.jrc 12" + +# +# ICEpick-D (JTAG route controller) +# +if { [info exists JRC_TAPID ] } { + set _JRC_TAPID $JRC_TAPID +} else { + set _JRC_TAPID 0x0b94402f +} +jtag newtap $_CHIPNAME jrc -irlen 6 -ircapture 0x1 -irmask 0x3f -expected-id $_JRC_TAPID +jtag configure $_CHIPNAME.jrc -event setup "jtag tapenable $_CHIPNAME.dap" +# some TCK tycles are required to activate the DEBUG power domain +jtag configure $_CHIPNAME.jrc -event post-reset "runtest 100" + +# +# Cortex A8 target +# +set _TARGETNAME $_CHIPNAME.cpu +target create $_TARGETNAME cortex_a8 -chain-position $_CHIPNAME.dap -dbgbase 0x80001000 + +# SRAM: 64K at 0x4030.0000; use the first 16K +$_TARGETNAME configure -work-area-phys 0x40300000 -work-area-size 0x4000 + +$_TARGETNAME configure -event reset-assert "am335x_dbginit $_TARGETNAME" +$_TARGETNAME configure -event reset-assert-post "am335x_dbginit $_TARGETNAME" + +$_TARGETNAME configure -event gdb-attach { + global _TARGETNAME + am335x_dbginit $_TARGETNAME + echo "Halting target" + halt +} + +# Run this to enable invasive debugging. This is run automatically in the +# reset sequence. +proc am335x_dbginit {target} { + # General Cortex A8 debug initialisation + cortex_a8 dbginit +} + |