tcl: Adapt config files to new ftdi command syntax

The patch was created automatically using the following
script:

%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---
(cat << EOF
ftdi_device_desc ftdi device_desc
ftdi_serial ftdi serial
ftdi_channel ftdi channel
ftdi_layout_init ftdi layout_init
ftdi_layout_signal ftdi layout_signal
ftdi_set_signal ftdi set_signal
ftdi_get_signal ftdi get_signal
ftdi_vid_pid ftdi vid_pid
ftdi_tdo_sample_edge ftdi tdo_sample_edge
EOF
) | while read a b; do
sed -i "s/$a/$b/g" $(find tcl -type f -name "*.cfg" )
done
%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---

Change-Id: Iff781f37bb5511b7e15cbe6dcdf6d28e89fb174f
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/6333
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>

15 files changed, 51 insertions, 51 deletions

diff --git a/tcl/board/digilent_analog_discovery.cfg b/tcl/board/digilent_analog_discovery.cfg
index 954e540..64cdacf 100644
--- a/tcl/board/digilent_analog_discovery.cfg
+++ b/tcl/board/digilent_analog_discovery.cfg
@@ -8,10 +8,10 @@
 #
 
 adapter driver ftdi
-ftdi_device_desc "Digilent USB Device"
-ftdi_vid_pid 0x0403 0x6014
+ftdi device_desc "Digilent USB Device"
+ftdi vid_pid 0x0403 0x6014
 
-ftdi_layout_init 0x8008 0x800b
+ftdi layout_init 0x8008 0x800b
 
 adapter speed 25000
 
diff --git a/tcl/board/digilent_nexys_video.cfg b/tcl/board/digilent_nexys_video.cfg
index f171e24..b60ec91 100644
--- a/tcl/board/digilent_nexys_video.cfg
+++ b/tcl/board/digilent_nexys_video.cfg
@@ -6,19 +6,19 @@
 adapter driver ftdi
 adapter speed 30000
 
-ftdi_device_desc "Digilent USB Device"
-ftdi_vid_pid 0x0403 0x6010
+ftdi device_desc "Digilent USB Device"
+ftdi vid_pid 0x0403 0x6010
 
 # channel 0 is dedicated for Digilent's DPTI Interface
 # channel 1 is used for JTAG
-ftdi_channel 1
+ftdi channel 1
 
 # just TCK TDI TDO TMS, no reset
-ftdi_layout_init 0x0088 0x008b
+ftdi layout_init 0x0088 0x008b
 reset_config none
 
 # Enable sampling on falling edge for high JTAG speeds.
-ftdi_tdo_sample_edge falling
+ftdi tdo_sample_edge falling
 
 transport select jtag
 
diff --git a/tcl/board/dp_busblaster_v3.cfg b/tcl/board/dp_busblaster_v3.cfg
index a9974d9..b94b43a 100644
--- a/tcl/board/dp_busblaster_v3.cfg
+++ b/tcl/board/dp_busblaster_v3.cfg
@@ -8,6 +8,6 @@
 #
 
 source [find interface/ftdi/dp_busblaster.cfg]
-ftdi_channel 1
+ftdi channel 1
 
 jtag newtap xc2c32a tap -expected-id 0x06e1c093 -irlen 8
diff --git a/tcl/board/dp_busblaster_v4.cfg b/tcl/board/dp_busblaster_v4.cfg
index 7b3bee8..2c2f0e9 100644
--- a/tcl/board/dp_busblaster_v4.cfg
+++ b/tcl/board/dp_busblaster_v4.cfg
@@ -14,6 +14,6 @@
 #
 
 source [find interface/ftdi/dp_busblaster.cfg]
-ftdi_channel 1
+ftdi channel 1
 
 jtag newtap xc2c64a tap -expected-id 0x06e5c093 -irlen 8
diff --git a/tcl/board/gumstix-aerocore.cfg b/tcl/board/gumstix-aerocore.cfg
index f0103ed..565df4c 100644
--- a/tcl/board/gumstix-aerocore.cfg
+++ b/tcl/board/gumstix-aerocore.cfg
@@ -1,10 +1,10 @@
 # JTAG for the STM32F4x chip used on the Gumstix AeroCore is available on
 # the first interface of a Quad FTDI chip.  nTRST is bit 4.
 adapter driver ftdi
-ftdi_vid_pid 0x0403 0x6011
+ftdi vid_pid 0x0403 0x6011
 
-ftdi_layout_init 0x0000 0x001b
-ftdi_layout_signal nTRST -data 0x0010
+ftdi layout_init 0x0000 0x001b
+ftdi layout_signal nTRST -data 0x0010
 
 source [find target/stm32f4x.cfg]
 reset_config trst_only
diff --git a/tcl/board/kasli.cfg b/tcl/board/kasli.cfg
index d492249..7cfdcf2 100644
--- a/tcl/board/kasli.cfg
+++ b/tcl/board/kasli.cfg
@@ -1,8 +1,8 @@
 adapter driver ftdi
-ftdi_device_desc "Quad RS232-HS"
-ftdi_vid_pid 0x0403 0x6011
-ftdi_channel 0
-ftdi_layout_init 0x0008 0x000b
+ftdi device_desc "Quad RS232-HS"
+ftdi vid_pid 0x0403 0x6011
+ftdi channel 0
+ftdi layout_init 0x0008 0x000b
 # adapter usb location 1:8
 
 reset_config none
diff --git a/tcl/board/kindle2.cfg b/tcl/board/kindle2.cfg
index a39f15c..71dca74 100644
--- a/tcl/board/kindle2.cfg
+++ b/tcl/board/kindle2.cfg
@@ -37,7 +37,7 @@ jtag_ntrst_delay 30
 arm11 memwrite burst disable
 
 adapter speed 1000
-ftdi_tdo_sample_edge falling
+ftdi tdo_sample_edge falling
 
 proc kindle2_init {} {
 	imx3x_reset
diff --git a/tcl/board/nds32_corvettef1.cfg b/tcl/board/nds32_corvettef1.cfg
index cec1723..7300ce0 100644
--- a/tcl/board/nds32_corvettef1.cfg
+++ b/tcl/board/nds32_corvettef1.cfg
@@ -7,12 +7,12 @@
 adapter speed     10000
 
 adapter driver ftdi
-ftdi_device_desc "Dual RS232-HS"
-ftdi_vid_pid 0x0403 0x6010
+ftdi device_desc "Dual RS232-HS"
+ftdi vid_pid 0x0403 0x6010
 
-ftdi_layout_init 0x0c08 0x0f1b
-ftdi_layout_signal nTRST -data 0x0100 -noe 0x0400
-ftdi_layout_signal nSRST -data 0x0200 -noe 0x0800
+ftdi layout_init 0x0c08 0x0f1b
+ftdi layout_signal nTRST -data 0x0100 -noe 0x0400
+ftdi layout_signal nSRST -data 0x0200 -noe 0x0800
 reset_config srst_only
 
 source [find target/nds32v5.cfg]
diff --git a/tcl/board/numato_mimas_a7.cfg b/tcl/board/numato_mimas_a7.cfg
index d4012ba..12df891 100644
--- a/tcl/board/numato_mimas_a7.cfg
+++ b/tcl/board/numato_mimas_a7.cfg
@@ -8,13 +8,13 @@
 #       Therefore, prefer external power supply.
 
 adapter driver ftdi
-ftdi_device_desc "Mimas Artix 7 FPGA Module"
-ftdi_vid_pid 0x2a19 0x1009
+ftdi device_desc "Mimas Artix 7 FPGA Module"
+ftdi vid_pid 0x2a19 0x1009
 
 # channel 0 is for custom purpose by users (like uart, fifo etc)
 # channel 1 is reserved for JTAG (by-default) or SPI (possible via changing solder jumpers)
-ftdi_channel 1
-ftdi_tdo_sample_edge falling
+ftdi channel 1
+ftdi tdo_sample_edge falling
 
 
 # FTDI Pin Layout
@@ -28,7 +28,7 @@ ftdi_tdo_sample_edge falling
 # OE_N is JTAG buffer output enable signal (active-low)
 # PROG_B is not used, so left as input to FTDI.
 #
-ftdi_layout_init 0x0008 0x004b
+ftdi layout_init 0x0008 0x004b
 reset_config none
 adapter speed 30000
 
diff --git a/tcl/board/quark_d2000_refboard.cfg b/tcl/board/quark_d2000_refboard.cfg
index 8b8314a..a89895d 100644
--- a/tcl/board/quark_d2000_refboard.cfg
+++ b/tcl/board/quark_d2000_refboard.cfg
@@ -2,11 +2,11 @@
 
 # the board has an onboard FTDI FT232H chip
 adapter driver ftdi
-ftdi_vid_pid 0x0403 0x6014
-ftdi_channel 0
+ftdi vid_pid 0x0403 0x6014
+ftdi channel 0
 
-ftdi_layout_init 0x0000 0x030b
-ftdi_layout_signal nTRST -data 0x0100 -noe 0x0100
+ftdi layout_init 0x0000 0x030b
+ftdi layout_signal nTRST -data 0x0100 -noe 0x0100
 
 source [find target/quark_d20xx.cfg]
 
diff --git a/tcl/board/sayma_amc.cfg b/tcl/board/sayma_amc.cfg
index 64c0854..0bd76ba 100644
--- a/tcl/board/sayma_amc.cfg
+++ b/tcl/board/sayma_amc.cfg
@@ -11,19 +11,19 @@
 # which features an Artix 7 FPGA.
 
 adapter driver ftdi
-ftdi_device_desc "Quad RS232-HS"
-ftdi_vid_pid 0x0403 0x6011
-ftdi_channel 0
+ftdi device_desc "Quad RS232-HS"
+ftdi vid_pid 0x0403 0x6011
+ftdi channel 0
 # Use this to distinguish multiple boards by topology
 #adapter usb location 5:1
 # sampling on falling edge generally seems to work and accelerates things but
 # is not fully tested
-#ftdi_tdo_sample_edge falling
+#ftdi tdo_sample_edge falling
 # EN_USB_JTAG on ADBUS7: out, high
 # USB_nTRST on ADBUS4: out, high, but R46 is DNP
-ftdi_layout_init 0x0098 0x008b
-#ftdi_layout_signal EN_USB -data 0x0080
-#ftdi_layout_signal nTRST -data 0x0010
+ftdi layout_init 0x0098 0x008b
+#ftdi layout_signal EN_USB -data 0x0080
+#ftdi layout_signal nTRST -data 0x0010
 reset_config none
 
 adapter speed 5000
diff --git a/tcl/board/sifive-e31arty.cfg b/tcl/board/sifive-e31arty.cfg
index b7a255e..8e701f1 100644
--- a/tcl/board/sifive-e31arty.cfg
+++ b/tcl/board/sifive-e31arty.cfg
@@ -14,8 +14,8 @@ $_TARGETNAME.0 configure -work-area-phys 0x80000000 -work-area-size 10000 -work-
 flash bank spi0 fespi 0x40000000 0 0 0 $_TARGETNAME.0 0x20004000
 init
 if {[ info exists pulse_srst]} {
-  ftdi_set_signal nSRST 0
-  ftdi_set_signal nSRST z
+  ftdi set_signal nSRST 0
+  ftdi set_signal nSRST z
 }
 halt
 flash protect 0 64 last off
diff --git a/tcl/board/sifive-e51arty.cfg b/tcl/board/sifive-e51arty.cfg
index 20ad575..a543987 100644
--- a/tcl/board/sifive-e51arty.cfg
+++ b/tcl/board/sifive-e51arty.cfg
@@ -14,8 +14,8 @@ $_TARGETNAME.0 configure -work-area-phys 0x80000000 -work-area-size 10000 -work-
 flash bank spi0 fespi 0x40000000 0 0 0 $_TARGETNAME.0 0x20004000
 init
 if {[ info exists pulse_srst]} {
-  ftdi_set_signal nSRST 0
-  ftdi_set_signal nSRST z
+  ftdi set_signal nSRST 0
+  ftdi set_signal nSRST z
 }
 halt
 flash protect 0 64 last off
diff --git a/tcl/board/sifive-hifive1.cfg b/tcl/board/sifive-hifive1.cfg
index 196f540..c47485b 100644
--- a/tcl/board/sifive-hifive1.cfg
+++ b/tcl/board/sifive-hifive1.cfg
@@ -1,15 +1,15 @@
 adapter speed     10000
 
 adapter driver ftdi
-ftdi_device_desc "Dual RS232-HS"
-ftdi_vid_pid 0x0403 0x6010
+ftdi device_desc "Dual RS232-HS"
+ftdi vid_pid 0x0403 0x6010
 
-ftdi_layout_init 0x0008 0x001b
-ftdi_layout_signal nSRST -oe 0x0020 -data 0x0020
+ftdi layout_init 0x0008 0x001b
+ftdi layout_signal nSRST -oe 0x0020 -data 0x0020
 
 #Reset Stretcher logic on FE310 is ~1 second long
 #This doesn't apply if you use
-# ftdi_set_signal, but still good to document
+# ftdi set_signal, but still good to document
 #adapter srst delay 1500
 
 set _CHIPNAME riscv
@@ -23,8 +23,8 @@ flash bank onboard_spi_flash fespi 0x20000000 0 0 0 $_TARGETNAME
 init
 #reset -- This type of reset is not implemented yet
 if {[ info exists pulse_srst]} {
-  ftdi_set_signal nSRST 0
-  ftdi_set_signal nSRST z
+  ftdi set_signal nSRST 0
+  ftdi set_signal nSRST z
   #Wait for the reset stretcher
   #It will work without this, but
   #will incur lots of delays for later commands.
diff --git a/tcl/board/ti_tmdx570ls20susb.cfg b/tcl/board/ti_tmdx570ls20susb.cfg
index 87cab26..e71136c 100644
--- a/tcl/board/ti_tmdx570ls20susb.cfg
+++ b/tcl/board/ti_tmdx570ls20susb.cfg
@@ -12,5 +12,5 @@ reset_config trst_only
 
 # xds100v2 config says add this to the end
 init
-ftdi_set_signal PWR_RST 1
+ftdi set_signal PWR_RST 1
 jtag arp_init