diff options
Diffstat (limited to 'include/configs/motionpro.h')
| -rw-r--r-- | include/configs/motionpro.h | 329 |
1 files changed, 0 insertions, 329 deletions
diff --git a/include/configs/motionpro.h b/include/configs/motionpro.h deleted file mode 100644 index 75633f6..0000000 --- a/include/configs/motionpro.h +++ /dev/null @@ -1,329 +0,0 @@ -/* - * (C) Copyright 2003-2007 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - * - * Based on Motion-PRO board config file by Robert McCullough, rob@promessinc.com - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -/* - * High Level Configuration Options - */ - -/* CPU and board */ -#define CONFIG_MPC5200 1 /* This is a MPC5200 CPU */ -#define CONFIG_MOTIONPRO 1 /* ... on Promess Motion-PRO board */ - -#define CONFIG_HIGH_BATS 1 /* High BATs supported */ - -#define CONFIG_SYS_TEXT_BASE 0xfff00000 - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - -/* - * Command line configuration. - */ -#define CONFIG_CMD_REGINFO - -/* - * Serial console configuration - */ -#define CONFIG_PSC_CONSOLE 1 /* console is on PSC1 */ -#define CONFIG_NETCONSOLE 1 /* network console */ -#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 } - -/* - * Ethernet configuration - */ -#define CONFIG_MPC5xxx_FEC 1 -#define CONFIG_MPC5xxx_FEC_MII100 -#define CONFIG_PHY_ADDR 0x2 -#define CONFIG_PHY_TYPE 0x79c874 -#define CONFIG_RESET_PHY_R 1 - -/* - * Autobooting - */ -#undef CONFIG_BOOTARGS - -#define CONFIG_CMDLINE_EDITING 1 /* add command line history */ - -/* - * Default environment settings - */ -#define CONFIG_EXTRA_ENV_SETTINGS \ - "netdev=eth0\0" \ - "hostname=motionpro\0" \ - "netmask=255.255.255.0\0" \ - "ipaddr=192.168.1.106\0" \ - "serverip=192.168.1.100\0" \ - "gatewayip=192.168.1.100\0" \ - "console=ttyPSC0,115200\0" \ - "u-boot_addr=400000\0" \ - "kernel_addr=400000\0" \ - "fdt_addr=700000\0" \ - "ramdisk_addr=800000\0" \ - "multi_image_addr=800000\0" \ - "rootpath=/opt/eldk-4.2/ppc_6xx\0" \ - "u-boot=/tftpboot/motionpro/u-boot.bin\0" \ - "bootfile=/tftpboot/motionpro/uImage\0" \ - "fdt_file=/tftpboot/motionpro/motionpro.dtb\0" \ - "ramdisk_file=/tftpboot/motionpro/uRamdisk\0" \ - "multi_image_file=kernel+initrd+dtb.img\0" \ - "load=tftp ${u-boot_addr} ${u-boot}\0" \ - "update=prot off fff00000 +${filesize};" \ - "era fff00000 +${filesize}; " \ - "cp.b ${u-boot_addr} fff00000 ${filesize};" \ - "prot on fff00000 +${filesize}\0" \ - "ramargs=setenv bootargs root=/dev/ram rw\0" \ - "nfsargs=setenv bootargs root=/dev/nfs rw " \ - "nfsroot=${serverip}:${rootpath}\0" \ - "fat_args=setenv bootargs root=/dev/sda rw\0" \ - "mtdids=nor0=ff000000.flash\0" \ - "mtdparts=ff000000.flash:13m(fs),2m(kernel),384k(uboot)," \ - "128k(env),128k(redund_env)," \ - "128k(dtb),128k(user_data)\0" \ - "addcons=setenv bootargs ${bootargs} console=${console}\0" \ - "addmtd=setenv bootargs ${bootargs} mtdparts=${mtdparts}\0" \ - "addip=setenv bootargs ${bootargs} " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:" \ - "${netmask}:${hostname}:${netdev}:off panic=1 " \ - "console=${console}\0" \ - "net_nfs=tftp ${kernel_addr} ${bootfile}; " \ - "tftp ${fdt_addr} ${fdt_file}; " \ - "run nfsargs addip addmtd; " \ - "bootm ${kernel_addr} - ${fdt_addr}\0" \ - "net_self=tftp ${kernel_addr} ${bootfile}; " \ - "tftp ${fdt_addr} ${fdt_file}; " \ - "tftp ${ramdisk_addr} ${ramdisk_file}; " \ - "nfs ${ramdisk_addr} ${serverip}:${rootpath}/images/uRamdisk; " \ - "run ramargs addip addcons addmtd; " \ - "bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0" \ - "fat_multi=run fat_args addip addmtd; fatload ide 0:1 " \ - "${multi_image_addr} ${multi_image_file}; " \ - "bootm ${multi_image_addr}\0" \ - "" -#define CONFIG_BOOTCOMMAND "run fat_multi" - -/* - * do board-specific init - */ -#define CONFIG_BOARD_EARLY_INIT_R 1 - -/* - * Low level configuration - */ - -/* - * Clock configuration: SYS_XTALIN = 33MHz - */ -#define CONFIG_SYS_MPC5XXX_CLKIN 33000000 - -/* - * Set IPB speed to 100MHz - */ -#define CONFIG_SYS_IPBCLK_EQUALS_XLBCLK - -/* - * Memory map - */ -/* - * Warning!!! with the current BestComm Task, MBAR MUST BE set to 0xf0000000. - * Setting MBAR to otherwise will cause system hang when using SmartDMA such - * as network commands. - */ -#define CONFIG_SYS_MBAR 0xf0000000 -#define CONFIG_SYS_SDRAM_BASE 0x00000000 - -/* - * If building for running out of SDRAM, then MBAR has been set up beforehand - * (e.g., by the BDI). Otherwise we must specify the default boot-up value of - * MBAR, as given in the doccumentation. - */ -#if CONFIG_SYS_TEXT_BASE == 0x00100000 -#define CONFIG_SYS_DEFAULT_MBAR 0xf0000000 -#else /* CONFIG_SYS_TEXT_BASE != 0x00100000 */ -#define CONFIG_SYS_DEFAULT_MBAR 0x80000000 -#define CONFIG_SYS_LOWBOOT 1 -#endif /* CONFIG_SYS_TEXT_BASE == 0x00100000 */ - -/* Use SRAM until RAM will be available */ -#define CONFIG_SYS_INIT_RAM_ADDR MPC5XXX_SRAM -#define CONFIG_SYS_INIT_RAM_SIZE MPC5XXX_SRAM_SIZE - -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE -#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) -#define CONFIG_SYS_RAMBOOT 1 -#endif - -#define CONFIG_SYS_MONITOR_LEN (384 << 10) /* 384 kB for Monitor */ -#define CONFIG_SYS_MALLOC_LEN (1024 << 10) /* 1 MiB for malloc() */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* initial mem map for Linux */ - -/* - * Chip selects configuration - */ -/* Boot Chipselect */ -#define CONFIG_SYS_BOOTCS_START CONFIG_SYS_FLASH_BASE -#define CONFIG_SYS_BOOTCS_SIZE CONFIG_SYS_FLASH_SIZE -#define CONFIG_SYS_BOOTCS_CFG 0x00045D00 - -/* Flash memory addressing */ -#define CONFIG_SYS_CS0_START CONFIG_SYS_FLASH_BASE -#define CONFIG_SYS_CS0_SIZE CONFIG_SYS_FLASH_SIZE -#define CONFIG_SYS_CS0_CFG CONFIG_SYS_BOOTCS_CFG - -/* Dual Port SRAM -- Kollmorgen Drive memory addressing */ -#define CONFIG_SYS_CS1_START 0x50000000 -#define CONFIG_SYS_CS1_SIZE 0x10000 -#define CONFIG_SYS_CS1_CFG 0x05055800 - -/* Local register access */ -#define CONFIG_SYS_CS2_START 0x50010000 -#define CONFIG_SYS_CS2_SIZE 0x10000 -#define CONFIG_SYS_CS2_CFG 0x05055800 - -/* Anybus CompactCom Module memory addressing */ -#define CONFIG_SYS_CS3_START 0x50020000 -#define CONFIG_SYS_CS3_SIZE 0x10000 -#define CONFIG_SYS_CS3_CFG 0x05055800 - -/* No burst and dead cycle = 2 for all CSs */ -#define CONFIG_SYS_CS_BURST 0x00000000 -#define CONFIG_SYS_CS_DEADCYCLE 0x22222222 - -/* - * SDRAM configuration - */ -/* 2 x MT48LC16M16A2BG-75 IT:D, CASL 3, 32 bit data bus */ -#define SDRAM_CONFIG1 0x62322900 -#define SDRAM_CONFIG2 0x88c70000 -#define SDRAM_CONTROL 0x504f0000 -#define SDRAM_MODE 0x00cd0000 - -/* - * Flash configuration - */ -#define CONFIG_SYS_FLASH_CFI 1 /* Flash is CFI conformant */ -#define CONFIG_FLASH_CFI_DRIVER 1 -#define CONFIG_SYS_FLASH_BASE 0xff000000 -#define CONFIG_SYS_FLASH_SIZE 0x01000000 -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of memory banks */ -#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE } -#define CONFIG_SYS_MAX_FLASH_SECT 128 /* max num of sects on one chip */ -#define CONFIG_FLASH_16BIT /* Flash is 16-bit */ - -/* - * MTD configuration - */ -#define CONFIG_CMD_MTDPARTS -#define CONFIG_MTD_DEVICE /* needed for mtdparts commands */ -#define CONFIG_FLASH_CFI_MTD -#define MTDIDS_DEFAULT "nor0=motionpro-0" -#define MTDPARTS_DEFAULT "mtdparts=motionpro-0:" \ - "13m(fs),2m(kernel),384k(uboot)," \ - "128k(env),128k(redund_env)," \ - "128k(dtb),-(user_data)" - -/* - * IDE/ATA configuration - */ -#define CONFIG_SYS_ATA_BASE_ADDR MPC5XXX_ATA -#define CONFIG_SYS_IDE_MAXBUS 1 -#define CONFIG_SYS_IDE_MAXDEVICE 1 -#define CONFIG_IDE_PREINIT - -#define CONFIG_SYS_ATA_DATA_OFFSET 0x0060 -#define CONFIG_SYS_ATA_REG_OFFSET CONFIG_SYS_ATA_DATA_OFFSET -#define CONFIG_SYS_ATA_STRIDE 4 - -/* - * RTC configuration - */ -#define CONFIG_RTC_DS1337 1 -#define CONFIG_SYS_I2C_RTC_ADDR 0x68 - -/* - * Status LED configuration - */ - -#define ENABLE_GPIO_OUT 0x00000024 -#define LED_ON 0x00000010 - -/* - * Environment settings - */ -#define CONFIG_ENV_IS_IN_FLASH 1 -/* This has to be a multiple of the Flash sector size */ -#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN) -#define CONFIG_ENV_SIZE 0x1000 -#define CONFIG_ENV_SECT_SIZE 0x20000 - -/* Configuration of redundant environment */ -#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE) -#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) - -/* - * Pin multiplexing configuration - */ - -/* PSC1: UART1 - * PSC2: GPIO (default) - * PSC3: GPIO (default) - * USB: 2xUART4/5 - * Ethernet: Ethernet 100Mbit with MD - * Timer: CAN2/GPIO - * PSC6/IRDA: GPIO (default) - */ -#define CONFIG_SYS_GPS_PORT_CONFIG 0x1105a004 - -/* - * Motion-PRO's CPLD revision control register - */ -#define CPLD_REV_REGISTER (CONFIG_SYS_CS2_START + 0x06) - -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_LONGHELP /* undef to save memory */ -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ - -#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */ -#define CONFIG_SYS_MEMTEST_END 0x03e00000 /* 1 ... 62 MiB in DRAM */ -#define CONFIG_SYS_ALT_MEMTEST - -#define CONFIG_SYS_LOAD_ADDR 0x200000 /* default kernel load addr */ - -/* - * Various low-level settings - */ -#define CONFIG_SYS_HID0_INIT HID0_ICE | HID0_ICFI -#define CONFIG_SYS_HID0_FINAL HID0_ICE - -#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */ - -/* Not needed for MPC 5xxx U-Boot, but used by tools/updater */ -#define CONFIG_SYS_RESET_ADDRESS 0xfff00100 - -#define OF_CPU "PowerPC,5200@0" -#define OF_SOC "soc5200@f0000000" -#define OF_TBCLK (bd->bi_busfreq / 4) -#define OF_STDOUT_PATH "/soc5200@f0000000/serial@2000" - -#endif /* __CONFIG_H */ |