- Apr 24, 2022
-
-
David Jander authored
Following changes was made: - Add MDIO signal names - Add missing ISB_IN2 name. Also correct ISB_nIN1. These two signals were used together in older HW revisions. Later ISB_IN2 was removed. Software should still be able to use both. - Add missing CAN1 and UART line names - Add missing ON1/2_CTRL line names - fix CPU_* line names. The real signal names are without the CPU_ prefix, like on imx6qdl-vicut1.dtsi - Fix ETH_INT signal name Signed-off-by:
David Jander <david@protonic.nl> Signed-off-by:
Oleksij Rempel <o.rempel@pengutronix.de> Signed-off-by:
Shawn Guo <shawnguo@kernel.org>
-
David Jander authored
Only the prototype had the SATA interface. There are no existing products with SATA interface and no plans to add any. Signed-off-by:
-
David Jander authored
The function of DISP0_DAT9 is dependent on hardware revision of two particular variants. This setting should be done by the bootloader anyway, and is not needed in the kernel, so remove it from the DT. Signed-off-by:
-
David Jander authored
Add some missing names and remove names to pins that have never been used and/or are not present on any hardware. Signed-off-by:
-
David Jander authored
While there are LEDs connected on some variants on GPIO4 pins 16 and 17, those are not the debug LEDs that should be visible to user-space. It should be the same as in imx6dl-victgo.dtsi. Signed-off-by:
-
David Jander authored
The names should be consistent with the names in imx6dl-victgo.dts This patch is preparation to unify vicut1 and victgo DTs. Signed-off-by:
-
David Jander authored
Only first prototype had UART2 and there are no plans to add it in the future. Signed-off-by:
-
David Jander authored
Only the very first prototypes had PCIe and there are no plant to add it in the future. Signed-off-by:
-
David Jander authored
Unify nON_SWITCH pinctrl configuration with imx6dl-victgo.dts. This patch is a preparation to reduce duplicated code between vicut1 and victgo. Signed-off-by:
-
David Jander authored
Only the first prototypes had a TiWi module. There is no publicly available hardware where this module is fitted and there are no plan to produce any. Signed-off-by:
-
- Apr 19, 2022
-
-
Max Krummenacher authored
Add support for Toradex Aster, small form-factor with header compatible with Arduino Uno and Raspberry Pi (RPi) maker boards. Additional detail available at https://www.toradex.com/products/carrier-boards/aster-carrier-board Signed-off-by:
Max Krummenacher <max.krummenacher@toradex.com> Signed-off-by:
-
Max Krummenacher authored
Add support for Toradex Iris, small form-factor Pico-ITX Colibri Arm Computer Module family Carrier Board. Additional details available at https://www.toradex.com/products/carrier-board/iris-carrier-board Signed-off-by:
-
Max Krummenacher authored
The Toradex board Iris V2 has a SD-card slot with switchable power. Add a pinctrl sleep used when the card power is off to avoid backfeeding to the card and add the "sleep" pinctrl to the usdhc1 controller. Signed-off-by:
-
Max Krummenacher authored
- Sort pinctrl nodes alphabetically - End all pinctrl node names in grp and avoid using dashes - Change pinctrl_usbc_id_1's node name to not use underscores - Change the pmic's node name to pmic@8 per binding requirement - Add sound-dai-cells to the codec node per binding requirement Signed-off-by:
-
Max Krummenacher authored
The following two nodes define module level functionality, move them from the carrier board dts file to the SoM file. While at it, reorder the properties in the gpio-keys node alphabetical. - gpio-keys defining the wakeup pin - memory node The atmel touchscreen node can be used on any carrier board. Move it from the carrier board to the module-level device tree and keep it disabled. Set the default pinmuxing to the dedicated connector available on newer carrier boards and rename the pinctrl labels specifying the INT/Reset signal to a common pattern. pinctrl_atmel_conn - uses 107/106 pins as used on dedicated connector pinctrl_atmel_adap - uses 28/30 pins as used with jumper wires Signed-off-by:
-
Max Krummenacher authored
The Toradex board Iris V2 has an LVDS transceiver which is configured with 4 signals. Add corresponding pins into the separate pingroup to be able to manage the transceiver. Signed-off-by:
-
Max Krummenacher authored
The Colibri iMX6 HW doesn't allow to use the PWR_ON_REQ signal for poweroff. Use the fsl,pmic-stby-poweroff property to command the PMIC into a low power mode in poweroff. Signed-off-by:
-
Max Krummenacher authored
The Toradex Colibri family is composed of SoM that can be plugged in various carrier board, with carrier boards allowing multiple optional add-on (e.g. display, camera, ...). Keep all the SoM specific part into the module .dtsi, disabling everything that is not self-contained on the board. The carrier board dts can reuse/enable anything that is defined in the module dtsi. Additional device tree overlays can be used for any accessories that are plugged in the carrier board. Disable parallel RGB: The parallel RGB interface (lcd_display) and all related nodes can be enabled in an overlay if used. Keep all nodes disabled in the module-level device tree. Rename display interface node to match imx6qdl-apalis to make it easier to use overlays. The pwm-backlight binding now requires the power-supply property, add it. Disable stmpe touchscreen: The touchscreen can be enabled in an overlay if used. Add labels to the stmpe sub nodes. Disable hdmi interface: HDMI can be enabled in an overlay if used. Update SPDX-License spelling to latest convention. Update Copyright year. Signed-off-by:
-
Oleksandr Suvorov authored
Add GPIO line names on module level. Those are all GPIOs which a user might use on his custom carrier board. If more meaningful names are available on the carrier board, the user can overwrite the line names in the carrier board level device tree. Signed-off-by:
Oleksandr Suvorov <oleksandr.suvorov@toradex.com> Signed-off-by:
-
Max Krummenacher authored
Fix names of extra pingroup node and property for gpio bus recovery. Without the change i2c2 is not functional. Fixes: 56f0df6b ("ARM: dts: imx*(colibri|apalis): add missing recovery modes to i2c") Signed-off-by:
-
- Apr 18, 2022
-
-
Max Krummenacher authored
Drop Colibri V1.1 device tree, this is just a duplicate of Colibri V1.0 with the possibility to use SD cards in UHS mode if the carrier board does not have 3.3V pull up resistor. The dedicated device tree kept the feature switched of by setting the no-1-8-v property and thus does not offer anything different than what the regular device tree does. Thus drop the dedicated device tree and merge the preparation to allow enabling the feature should a carrier without pull ups be used into the regular device tree. Signed-off-by:
-
- Apr 11, 2022
-
-
Krzysztof Kozlowski authored
The node names should be generic and SPI NOR dtschema expects "flash". Signed-off-by:
Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Signed-off-by:
-
Thorsten Scherer authored
Commit f3e7dae3 ("ARM: dts: imx6qdl: add enet_out clk support") added another item to the list of clocks for the fec device. As imx6dl-eckelmann-ci4x10.dts only overwrites clocks, but not clock-names this resulted in an inconsistency with clocks having one item more than clock-names. Also overwrite clock-names with the same value as in imx6qdl.dtsi. This is a no-op today, but prevents similar inconsistencies if the soc file will be changed in a similar way in the future. Signed-off-by:
Thorsten Scherer <t.scherer@eckelmann.de> Reviewed-by:
Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Fixes: f3e7dae3 ("ARM: dts: imx6qdl: add enet_out clk support") Signed-off-by:
-
Uwe Kleine-König authored
clocks and clock-names are already present in imx6qdl.dtsi since commit f3e7dae3 ("ARM: dts: imx6qdl: add enet_out clk support"). The change to imx6qdl.dtsi was explicitly done to avoid this construct in this file, so benefit from the change and drop these properties. Signed-off-by:
-
- Apr 09, 2022
-
-
Alexander Stein authored
Schema requires the node being named 'pinctrl'. Signed-off-by:
Alexander Stein <alexander.stein@ew.tq-group.com> Signed-off-by:
-
- Apr 06, 2022
-
-
Andrej Picej authored
Instead of changing default pwm-cells property, use the default "#pwm-cells = <3>" and add the third option. Signed-off-by:
Andrej Picej <andrej.picej@norik.com> Signed-off-by:
-
Alexander Bauer authored
Add support for the PHYTEC phyGATE-Tauri-S with i.MX 6ULL with eMMC or NAND. Supported features: * eMMC/NAND * i2c RTC * i2c TEMP * PMIC * PWM * debug UART * CAN * SD card * 2x 1Gbit Ethernet * RS232/RS485 * USB 2.0 Host * TPM * SPI-NOR Signed-off-by:Alexander Bauer <a.bauer@phytec.de> Signed-off-by:
Jens Lang <j.lang@phytec.de> Signed-off-by:
-
Alexander Stein authored
Add device trees for the MBa6ULx mainboard with TQMa6ULLxL SoMs. Signed-off-by:
-
Alexander Stein authored
Add device trees for the MBa6ULx mainboard with TQMa6ULLx SoMs. Signed-off-by:
-
Alexander Stein authored
Add device trees for the MBa6ULx mainboard with TQMa6ULxL SoMs. Signed-off-by:
-
Alexander Stein authored
Add device trees for the MBa6ULx mainboard with TQMa6ULx SoMs. Signed-off-by:
-
David Jander authored
The gpio1 0 pin is controlling CAN termination, not USB H1 VBUS. So, remove wrong regulator and assign this gpio to new DT CAN termination property. Signed-off-by:
-
Robin van der Gracht authored
This series of devices is using lg,lb070wv8 instead of kyo,tcg121xglp. Signed-off-by:
Robin van der Gracht <robin@protonic.nl> Signed-off-by:
-
Robin van der Gracht authored
Interrupt counter is mainlined, now we can add missing counter nodes. Signed-off-by:
-
David Jander authored
countedX lines have different board names (YACO_x). And REV_ and BOARD_ pins have multiple functions. So, use names exposed to the OS. Signed-off-by:
-
David Jander authored
backlight_led is the dimmable backlight for the rubber border on the case. It is also used to highlight the power- and some other buttons. MX6QDL_PAD_SD4_DAT1__PWM3_OUT is also assigned as output for pwm3. Since we need pwm3 for the backlight, we're forced to disable user space hardware revision detection. The bootloader will have to supply this information (i.e. through device tree). Signed-off-by:
-
David Jander authored
We have two backlight sources on this boards. Use more specific name for the LCD backlight to see the difference. Signed-off-by:
-
David Jander authored
Recover default behavior of the device and set maximal brightness Signed-off-by:
-
- Apr 04, 2022
-
-
Linus Torvalds authored
-
git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-traceLinus Torvalds authored
Pull more tracing updates from Steven Rostedt: - Rename the staging files to give them some meaning. Just stage1,stag2,etc, does not show what they are for - Check for NULL from allocation in bootconfig - Hold event mutex for dyn_event call in user events - Mark user events to broken (to work on the API) - Remove eBPF updates from user events - Remove user events from uapi header to keep it from being installed. - Move ftrace_graph_is_dead() into inline as it is called from hot paths and also convert it into a static branch. * tag 'trace-v5.18-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace: tracing: Move user_events.h temporarily out of include/uapi ftrace: Make ftrace_graph_is_dead() a static branch tracing: Set user_events to BROKEN tracing/user_events: Remove eBPF interfaces tracing/user_events: Hold event_mutex during dyn_event_add proc: bootconfig: Add null pointer check tracing: Rename the staging files for trace_events
-
