- Dec 19, 2013
-
-
- Dec 18, 2013
-
-
Johannes Berg authored
Signed-off-by:
Johannes Berg <johannes.berg@intel.com> Reviewed-by:
EyalX Shapira <eyal@wizery.com> Signed-off-by:
Emmanuel Grumbach <emmanuel.grumbach@intel.com>
-
Eyal Shapira authored
RTS protection was turned on once aggregation was enabled but it was never turned off. Remove turning on RTS protection in the LQ command completely as TX_CMD_FLG_PROT_REQUIRE gets set in iwl_mvm_set_tx_cmd for every Tx which is part of an aggregation. This would already cause RTS protection to be used during aggregations. Signed-off-by:
-
Eyal Shapira authored
Set the Tx/Rx highest long GI rates in the VHT Supported MCS Set field according to the chip capabilties. Signed-off-by:
-
Eyal Shapira authored
MCS9 introduces some corner cases in the current rs algorithm which may lead to non optimal throughput and instability in the throughput. Until all the corner cases are resolved disable MCS9 for Tx as a workaround which yields better throughput results as MCS8 is much more stable. Signed-off-by:
-
Ilan Peer authored
Fix a regression introduced in "iwlwifi: mvm: fix ht protection flags" where an AP/IBSS MAC context could have been updated even before the context was added to the FW. This fix avoids the following warning: WARNING: ... at .../drivers/net/wireless/iwlwifi/mvm/mac-ctxt.c:1132 iwl_mvm_mac_ctxt_changed+0x75/0x90 [iwlmvm]() Changing inactive MAC 0c:8b:fd:01:1a:30/3 Modules linked in: [...] Call Trace: [<c16041fd>] dump_stack+0x41/0x52 [<c1041074>] warn_slowpath_common+0x84/0xa0 [<f80d8f45>] ? iwl_mvm_mac_ctxt_changed+0x75/0x90 [iwlmvm] [<f80d8f45>] ? iwl_mvm_mac_ctxt_changed+0x75/0x90 [iwlmvm] [<c1041133>] warn_slowpath_fmt+0x33/0x40 [<f80d8f45>] iwl_mvm_mac_ctxt_changed+0x75/0x90 [iwlmvm] [<f80d517a>] iwl_mvm_bss_info_changed+0x22a/0x4b0 [iwlmvm] [<c160831d>] ? mutex_unlock+0xd/0x10 [<f80d4678>] ? iwl_mvm_configure_filter+0x58/0x70 [iwlmvm] [<f80d4f50>] ? iwl_mvm_mac_tx+0xc0/0xc0 [iwlmvm] [<f8132d83>] ieee80211_bss_info_change_notify+0xa3/0x1d0 [mac80211] [<f8149247>] ? ieee80211_del_virtual_monitor+0x127/0x1f0 [mac80211] [<f8149cac>] ieee80211_do_open+0x12c/0xeb0 [mac80211] [<c106c6de>] ? __raw_notifier_call_chain+0x1e/0x30 [<c106c70f>] ? raw_notifier_call_chain+0x1f/0x30 [<f814aa8d>] ieee80211_open+0x5d/0x60 [mac80211] [<c1500c7b>] __dev_open+0xab/0x140 [<c160b39a>] ? _raw_spin_unlock_bh+0x2a/0x30 [<c1500f41>] __dev_change_flags+0x81/0x160 [<c10ab6fc>] ? __lock_is_held+0x3c/0x60 [<c15010d1>] dev_change_flags+0x21/0x60 Signed-off-by:Ilan Peer <ilan.peer@intel.com> Reported-by:
-
Emmanuel Grumbach authored
debufs.o appeared twice in the Makefile. Fix that. Signed-off-by: -
Eyal Shapira authored
Extract the scale action decision to a different function in preparation of modifying it. While at it also convert the scale action values from hardcoded values to a clear enum. Signed-off-by:
-
Eyal Shapira authored
The logs are emitted in a flow in which there were retries and the rates in the rate table entry didn't match the active or search table. This doesn't indicate a problem and is expected in most cases where there will be retries for some reason. Remove the logs. Signed-off-by:
-
Eyal Shapira authored
The new logic will attempt more rates with less retries per rate. Also when starting off with MIMO it will fallback to SISO with the same MCS and only then to Legacy. Previously we fell back directly to Legacy. Signed-off-by:
-
Eyal Shapira authored
The supported legacy rate mask is initialized when rs is initialized based on the remote peer supported rates. There's no need to re mask it repeatedly with the supported remote peer rates. Signed-off-by:
-
Eyal Shapira authored
Simplify the code a bit more by extracting the rates table building logic into a separate function and handle setting a fixed rate for debug in a separate flow. Also avoid using and saving ucode rate format in different places. Instead use rs_rate struct and convert to ucode format only when filling the rates table in the LQ command. Signed-off-by:
-
Alexander Bondar authored
Current firmware doesn't handle well uAPSD in P2P Client. When it will be fixed, the firmware will set a TLV flag to notify the driver that uAPSD is supported in P2P client mode. Check this flag when sending power command for P2P client. Signed-off-by:
Alexander Bondar <alexander.bondar@intel.com> Signed-off-by:
-
Arik Nemtsov authored
It is not currently implemented for SDIO, and not required for other slave buses as well. Signed-off-by:
Arik Nemtsov <arik@wizery.com> Signed-off-by:
-
Arik Nemtsov authored
Clear the FW_ERROR status before the common start_fw transport code. Remove the transport specific clears. After these patches the FW_ERROR flag is only set and cleared by common transport code. Signed-off-by:
-
Arik Nemtsov authored
In case a sync command timeouts or Tx is stuck while a FW error interrupt arrives, we might call iwl_op_mode_nic_error twice before a restart has been initiated. This will cause a reprobe. Unify calls to this function at the transport level and only call it on the first FW error in a given by checking the transport FW error flag. While at it, remove the privately defined iwl_nic_error from PCIE code and use the common callback instead. Signed-off-by:
-
Eliad Peller authored
iwl_nvm_init() return value wasn't checked in some path, which resulted in the following panic (if there was some issue with the nvm): Unable to handle kernel NULL pointer dereference at virtual address 00000004 pgd = d0460000 [00000004] *pgd=00000000 Internal error: Oops: 5 [#1] PREEMPT SMP Modules linked in: iwlmvm(+) iwlwifi mac80211 cfg80211 compat [last unloaded: compat] PC is at iwl_mvm_mac_setup_register+0x12c/0x460 [iwlmvm] LR is at 0x2710 pc : [<bf50dd4c>] lr : [<00002710>] psr: 20800013 sp : d00cfe18 ip : 0000081e fp : d006b908 r10: d0711408 r9 : bf532e64 r8 : d006b5bc r7 : d01af000 r6 : bf39cefc r5 : d006ab00 r4 : d006b5a4 r3 : 00000001 r2 : 00000000 r1 : d006a120 r0 : d006b860 Signed-off-by:
Eliad Peller <eliad@wizery.com> Signed-off-by:
-
Emmanuel Grumbach authored
This pointer was not used anywhere. Signed-off-by: -
Eyal Shapira authored
Move rs_program_fix_rate right before it's caller where we're already in the context of an ifdef CPTCFG_MAC80211_DEBUGFS so we can get rid of the extra ifdefs surrounding the original location. Signed-off-by:
-
Arik Nemtsov authored
Stop Tx and commands from arriving to the transport layer when a FW error has occurred. A HW recovery should take place before. Remove transport specific checks of the same nature (note that not all transports were protected). Signed-off-by:
-
Arik Nemtsov authored
The same bits are employed in all transport layers. Put the status field in the common transport layer. This allows us to employ them in common transport code. Signed-off-by:
-
Arik Nemtsov authored
The stop_hw trans callback is not well defined. It is missing in many cleanup flows and the division of labor between stop_device/stop_hw is cumbersome. Remove stop_hw and use stop_device to perform both. Implement this for all current transports. PCIE needs some extra configuration the op-mode is leaving to configure RF kill. Expose this explicitly as a new op_mode_leave trans callback. Take the call to stop_device outside iwl_run_mvm_init_ucode, this makes more sense and WARN when we want to run the INIT firmware while it has run already. Signed-off-by:
-
Johannes Berg authored
The documentation for smps_requests is unclear, rewrite it. Signed-off-by:
-
Eliad Peller authored
Configure the phy context to the minimum required bandwidth, given by ctx->min_def. Tuning to a narrower bandwidth should reduce the noise level and consume less power. Signed-off-by:
-
Eliad Peller authored
Configure the fw to filter multicast according to the addresses given by mac80211. Note that bssid should be given even if we want to pass all the multicast frames. Signed-off-by:
-
Emmanuel Grumbach authored
This is more related to phy contexts than to mac context. Move this function to there. Signed-off-by: -
Alexander Bondar authored
This allows to tweak the power parameters per vif. Signed-off-by:
-
Alexander Bondar authored
Enable power save on P2P client interface only if it is the only bound interface. Avoid using uAPSD if P2P client is associated to GO that uses opportunistic power save. This is due to current FW limitation. Signed-off-by:
-
Alexander Bondar authored
When monitor interface is activated device power save needs to be disabled. Re-consider power management status on other active interfaces when monitor interface is bound or unbound. Signed-off-by:
-
Alexander Bondar authored
FW still does not support power management on multiple MAC interfaces. Currently the driver enforce this limitation by disabling PM if second interface is added. Change this behavior to allow PM on a single interface even if other interfaces exist but not bound to any specific PHY. PM will be enabled if only one single interface is bound. Signed-off-by:
-
Alexander Bondar authored
FW implements protective algorithm to identify AP's improper uAPSD behavior. FW sends misbehaving AP notification in this case. Add this notification handling. Avoid using uAPSD in next association to the exactly same AP. Refactor iwl_mvm_power_build_cmd() to move uAPSD related code to a separate function. Signed-off-by:
-
Eyal Shapira authored
If the device is MIMO and VHT capable it supports Tx STBC. Unlike HT, any chip that supports VHT also support STBC so no need for a config parameter. Using num_of_ants multiple times warranted caching it. Signed-off-by:
-
Eyal Shapira authored
It was set to zero which reflects support of a single STS. Set according to the number of Rx antennas which correctly reflects the number of STSs the STA can receive in a VHT NDP. This improves beamforming and has been tested to improve Rx throughput. Signed-off-by:
-
Eyal Shapira authored
Not all chips support STBC so allow this to be another config parameter per chip type. If STBC is supported then publish it in the HT caps. Since 7260/7265/3160 chips support it - set the stbc support bit. Signed-off-by:
-
Max Stepanov authored
This patch adds a cipher scheme support to extend a set of the supported ciphers. The driver reads a cipher scheme list TLV from FW image and passes it to mac80211 on hw registration. After the cipher schemes are registered the driver handles key installation and Tx/Rx calls related to the new ciphers. Signed-off-by:
Max Stepanov <Max.Stepanov@intel.com> Reviewed-by:
-
Lilach Edelstein authored
Send firmware a Smart FIFO Configuration host command to allow interrupt coalescing. The smart FIFO is enabled when there is only one bound interface (other than p2p devices which are ignored) and it is of type station, and activated while the station is associated. Smart Fifo allows aggragations of DMA transactions and by that causes processor and memory controller to stay for a longer time on lower c-states, thus saving platform power. Firmware relies on driver to activate and disable it. Signed-off-by:
Lilach Edelstein <lilach.edelstein@intel.com> Signed-off-by:
-
- Dec 16, 2013
-
-
Janusz Dziedzic authored
Add VHT MCS/NSS set support for nl80211_set_tx_bitrate_mask(). This should be used mainly for test purpose, to check different MCS/NSS VHT combinations. Signed-off-by:
Janusz Dziedzic <janusz.dziedzic@tieto.com> Signed-off-by:
-
Max Stepanov authored
Allow to read management keys stored in a station's gtk key array with a get_key function. Signed-off-by:
-
Max Stepanov authored
Verify that a pairwise key index value on ieee80211_get_key call doesn't exceed the boundaries of the pairwise key array. Signed-off-by:
-
Luciano Coelho authored
The return value of ieee80211_ibss_csa_beacon is not aligned with the return value of ieee80211_assign_beacon(). For consistency and to be able to use both functions with similar code, change ieee80211_ibss_csa_beacon() not to send the bss changed notification itself, but return what has changed so the caller can send the notification instead. Tested by: Simon Wunderlich <sw@simonwunderlich.de> Acked by: Simon Wunderlich <sw@simonwunderlich.de> Signed-off-by:
Luciano Coelho <luciano.coelho@intel.com> Signed-off-by:
-
