In some testing configuration, the firmware restart flow is
not enabled. Allow to collect logs even in this case.

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Reading the temperature directly from the hardware, without the help
of the firmware, is a complex process and is not entirely the same for
different hardware.  Also, some NICs don't easily allow access to the
sensors when the firmware is not running, which would add even more
complexity to the code.

To reduce the code complexity and to avoid code duplication between
the firmware and the driver, boot the firmware briefly to read the
current temperature while in CT kill mode.

Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

A lot of the newer d0i3 ref additions weren't added to the
debugfs file, fix that and add a comment to remember to do
it in the future.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Signed-off-by: Avri Altman <avri.altman@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

trivial, but this is user visible b/c it is in the help text

Signed-off-by: Toralf Förster <toralf.foerster@gmx.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

When updating quota in the firmware, it has to reset quite a bit
of internal state, which apparently can have an adverse impact on
its operation.

Avoid that by only updating the quota command when there are any
signification changes, i.e. added/removed bindings or changes in
quota that are bigger than 8 TU within a binding.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

The sharing model will differ in new hardware. Define the
non shared antenna based on the device so that different
devices can have different names for the non shared antenna.

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

When freeing the structures used for command data, clear their
memory as they may have contained key material at some point.
Also clear the duplicated buffer when freeing it to be safe;
currently key material is never put there but that may change.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Rather than ANDing with a mask - use existing macros, which
are more readable.

Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

This configuration is not needed for dvm, and it actually
broke it.

Reported-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

When disabling aggregation, disable the queues in the station
DB in the firmware, otherwise we leave the tfd_queue_mask in
a wrong state after an aggregation session has been torn down.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Move the tx stats to the persistent area of lq_sta to
avoid them being zeroed out every time rs reinitializes
which happens after tx idle for 5 secs for example.
The automatic zeroing out made them difficult to use.

Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Add MVM_FW_MCAST_FILTER_PASS_ALL option to iwl-dbg-cfg.ini configuration file
to enable/disable FW multicast filtering.

Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

If the ucode is not loaded, don't allow the temperature test to be
started, but allow it to be changed or stopped if already running.

Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

We rely on the value of the mvm->ucode_loaded flag to decide whether
or not we can perform certain operations (e.g. access to some debugfs
entries), so we need to reset it when the mac80211 stop operation is
called and the hardware is shutdown.

Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

max_rate_idx constraint is deprecated and it's handling is
faulty as well as it is relevant only for legacy rates but
was considered in HT/VHT. In most cases there was no side effect
as max_rate_idx was set to -1 but in certain cases like P2P
it got set to an actual rate idx which would limit the maximum
rate in HT/VHT by mistake.
max_rate_idx should be replaced by the masks fields but for
now remove it.

Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

This chip family supports LDPC so enable it.

Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

The firwmare now allows the driver to disable dummy
notifications. These notifications sent by the firmware
are an overhead for slow buses. They are still useful for
fast buses.
Add a hardware switch to prevent these notifications only
on devices that work on slow buses.

Signed-off-by: Eran <eran.harary@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Edit some 8000 series PCI IDs and add configuration to
Dual Band Wireless N 8260 devices.

Signed-off-by: Oren Givon <oren.givon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Use LDPC for Tx and publish support for Rx in case the chip
supports LDPC. Enable it for the 7265 family.

Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

The idea here is to translate a value of 0 received from
the firmware to the lowest rssi figure. As rx_status->chain_signal
is a signed byte the lowest possible value is -128 and not -256.
-256 was causing 0 to get stored in the signed byte.

Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

This change does the following:
1) Add a new 7265 series PCI ID
2) Add two new 3160 series PCI IDs
3) Add the new 3165 series PCI IDs and configurations

Signed-off-by: Oren Givon <oren.givon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

In
https://bugzilla.kernel.org/show_bug.cgi?id=84031

,
the submitter said that disabling power saving helped,
do just that.

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

smps_mode is used uninitialized in a debug statement in AP
mode, so always initialize it.

While at it, fix a typo.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

The latter is meant for software implementation of power
save and is not per-virtual interface. Since our driver
supports multiple virtual interfaces, we need to use
vif->bss_conf.dtim_period.

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Using the LQ table which is initially set according to
the rssi could lead to EAPOLs being sent in high legacy
rates like 54mbps.
It's better to avoid sending EAPOLs in high rates as it reduces
the chances of a successful 4-Way handshake.
Avoid this and treat them like other mgmt frames which would
initially get sent at the basic rate.

Cc: <stable@vger.kernel.org> [3.13+]
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

When mac80211 requests multiple BSS config changes, as for example
while associating, we ignore power management and QoS changes and
only apply them later. Fix that by removing the "else" and making
the conditions independent.

Also move it after (potential) beacon filter enablement to have
that already enabled when going into power management code.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

The chip is able to transmit up to 22dBm, so set
the constant appropriately.

CC: <stable@vger.kernel.org> [3.13+]
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

This code was broken on big endian systems. Sparse didn't
catch the bug since the firmware command was not tagged as
little endian.
Fix the bug for big endian systems and tag the field in the
firmware command to prevent such issues in the future.

Cc: stable@vger.kernel.org [3.14+]
Fixes: 1f3b0ff8

 ("iwlwifi: mvm: Add Smart FIFO support")
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

In commit cad3f08c (iwlwifi: mvm: enable MAC_FILTER_IN_BEACON when
forced_assoc_off is set) the code to set the MAC_FILTER_IN_BEACON flag
was accidentally moved to the main block of the if statement, while it
should be in the else block instead.  Move it to the right place.

Fixes: cad3f08c

 ("iwlwifi: mvm: enable MAC_FILTER_IN_BEACON when forced_assoc_off is set")
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

The variable 'u32 mode' exists twice, the latter shadowing
the former - remove the latter since there's no need for
two variables.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

The auxiliary station is being handled using the internal
station helper functions, clean that up and make the helpers
static.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Unify all the functions that handle the per-interface broadcast
station and make them have mvm and vif parameters. While at it,
add a new function to allocate the broadcast station instead of
open-coding it, and make the combined alloc+send and free+send
functions use the alloc/free & send functions.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

There are a few places that can call the function
iwl_mvm_mac_get_queues_mask() instead of open-coding the
equivalent, so do that. This requires changing it to return
the multicast queue as part of the bitmap, which broke GO
mode because including it in the broadcast station queues
seems to confuse the firmware, so work around that.

Also, the API defines that the CAB queue shouldn't be
included in the TFD queue mask, adjust the comment
accordingly (not a bug).

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Instead of checking whether a given station is the first to
be added on a client interface check for the new TDLS flag
and warn in the unexpected cases.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

The queue handling is a bit unclear - we have an array for
stop_count[IWL_MAX_HW_QUEUES] but indices really are the
mac80211 queue numbers. Change the array to be only of the
right size for mac80211 queues (IEEE80211_MAX_QUEUES) and
rename it to be clearer.

While at it, also remove the unused transport queue stop
bitmap in mvm.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Move all FIFO definitions together into the firmware API
header file and use the same enum/naming scheme for the
command FIFO.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

The firmware would like to have a MAC context (unassoc)
before the AP station is removed (we do this) but would
like to keep the BSSID until after it is removed, so we
need to send two commands - one with the BSSID before
and one without the BSSID after.

In order to do this, we need to store the BSSID as it
will have been cleared by mac80211 by the time we get
notified of the disassociation. Also pass it around as
an override to the various functions needing it, and
keep taking it from the mac80211 data otherwise. This
avoids having to keep track of the BSSID in all modes.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

During a channel switch we should tell the firmware to disable TX
temporarily and re-enable it after the switch is done.

Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>