Note that the default baudrate is 4800 instead of 9600 as a convenience
because that's what GPS devices want which is still the main use for
this driver.

Signed-off-by: Nicolas Pitre <npitre@mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

Add sdio_f0_readb() and sdio_f0_writeb() functions to reading and
writing function 0 registers.  Writes outside the vendor specific CCCR
registers (0xF0 - 0xFF) are not permitted.

Signed-off-by: David Vrabel <david.vrabel@csr.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

Replace all cases of BUG_ON with WARN_ON where there is a chance
(with varying degrees of slim) that the kernel can continue without
incidence.

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

Extend sdio_readsb(), sdio_writesb(), sdio_memcpy_fromio(), and
sdio_memcpy_toio() to handle any length of buffer by splitting the transfer
into several IO_RW_EXTENDED commands. Typically, a transfer would be split
into a single block mode transfer followed by a byte mode transfer for the
remainder but we also handle lack of block mode support and the block size
being greater than 512 (the maximum byte mode transfer size).

host->max_seg_size <= host->max_req_size so there's no need to check both
when determining the maximum data size for a single command.

Signed-off-by: David Vrabel <david.vrabel@csr.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

Before a driver is probed, set the function's block size to the default so the
driver is sure the block size is something sensible and it needn't explicitly
set it.

The default block size is the largest that's supported by both the card and
the host, with a maximum of 512 to ensure aribitrarily sized transfer use the
optimal (least) number of commands.

See http://lkml.org/lkml/2007/8/7/150

 for reasons for the block size choice.

Signed-off-by: David Vrabel <david.vrabel@csr.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

Signed-off-by: David Vrabel <david.vrabel@csr.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

SDIO doesn't have a CSD so it uses different timeout values than
SD memory.

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

Enable 4-bit data bus mode, according to host and card
capabilities.

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

Change clock speed to the highest supported by the card.

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

On Wed, Jul 25, 2007 at 04:03:04AM -0700, Andrew Morton wrote:
>...
> Changes since 2.6.22-rc6-mm1:
>...
>  git-mmc.patch
>...
>  git trees
>...

sdio_dev_attrs[] can become static.

Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

Signed-off-by: Nicolas Pitre <npitre@mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

Support the multi-byte transfer operation, including handlers for
common operations like writel()/readl().

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

This mimics what the serial_core does.  Useful for diagnostics.

Signed-off-by: Nicolas Pitre <npitre@mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

This currently only accepts the GPS class since that's all I have for
testing.  Tested with a Matsushita GPS and gpsd version 2.34.

Signed-off-by: Nicolas Pitre <npitre@mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

Signed-off-by: Nicolas Pitre <npitre@mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

It is sometimes necessary to give up on trying to claim the host lock,
especially if that happens in a thread that has to be stopped.

While at it, fix the description for mmc_claim_host() which was wrong.

Signed-off-by: Nicolas Pitre <npitre@mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

Signed-off-by: Nicolas Pitre <npitre@mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

Make the mmc bus uevent callback look like all other subsystems.

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

The problem is that the sdio_bus must be registered before any SDIO
drivers are registered against it otherwise the kernel sulks.  Because
the sdio_bus registration happens through module_init (equivalent to
device_initcall), then any SDIO
drivers linked before the SDIO core code in the kernel will be initialized
first.

Upcoming SDIO function drivers are likely to be located outside the
drivers/mmc directory as it is common practice to group drivers according
to their function rather than the bus they use.  SDIO drivers are therefore
likely to appear at random location in the kernel link.

To make sure the sdio_bus is always initialized before any SDIO drivers,
let's move the MMC init to the subsys_initcall level.

Signed-off-by: Nicolas Pitre <npitre@mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

Add a more clean separation between global, common CIS information
and the function specific one as we need the common information in
places where no specific function is specified.

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

This way those tuples that the core cares about are consumed by the core
code, and tuples that only function drivers might make sense of are
available to drivers.

Signed-off-by: Nicolas Pitre <npitre@mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

Signed-off-by: Nicolas Pitre <npitre@mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

Like many other buses, the devices (functions) on the SDIO bus
must be enabled before they can be used. Add functions that allow
drivers to do so.

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

Add command wrappers that simplify register access from SDIO
function drivers.

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

Add basic driver handling to the SDIO device model.

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

Add the sdio bus type and basic device handling.

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

Really basic init sequence for SDIO cards.

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

This kind of transfer is not supported, so don't advertise it and make it
fail early.

Signed-off-by: Marc Pignat <marc.pignat@hevs.ch>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

Some printk:s were missing an explicit level.

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

The MMC_DATA_MULTI flag never had a proper definition of what it
means, so remove it and let the drivers check the block count in
the request.

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

Remove the BYTEBLOCK capability and let the broken hosts fail the
requests with -EINVAL instead.

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

The write parameter in mmc_set_data_timeout() is redundant as the
data structure contains information about the direction of the
transfer.

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>