Read the DDBL1 and Ara DME attributes when activating an interface.

These values are currently provided by the SVC in the intf_hotplug
request, which is about to go away.

Note that there are currently no standard Ara VID and PID attributes and
that Toshiba uses attributes from the reserved space in ES3. For now, we
therefore refuse to enumerate any non-Toshiba bridges.

Also note that the Ara serial number is currently not supported.

Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Add NULL suffix to the don't-care DME selector index.

Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Clean up the device id-handling and make sure we never allocate invalid
device ids due to a missing upper bound.

Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Deactivate an interface immediately on enumeration failure.

Note that an interface is always registered.

Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Creating and destroying a route to an interface is arguably an interface
operation and belongs with the interface code.

Add new interface_activate and interface_deactivate helpers that will be
used to activate and deactivate an interface in the new interface boot
sequence.

Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Clean up handling of the ES3-bootrom quirks by adding an interface
quirk-flags field that is set appropriately when we detect that the ES3
bootrom is running.

Note that we need to reserve the DME_DIS_UNIPRO_BOOT_STARTED and
DME_DIS_FALLBACK_UNIPRO_BOOT_STARTED status values for the ES3 bootrom,
which does not support any CPort features (unlike later boot stages).
Add a BOOTROM infix to the defines to make this more clear.

Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Clean up and rename the interface-init-status helper.

Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

The ES2 boot status is stored in the least significant byte.

Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Reading and clearing the boot status of an interface is an interface
operation and belongs in the interface code.

As part of the reworked interface boot sequence, we also want to do this
when enabling (enumerating) a Greybus interface.

Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Use tabs to indent CPort-flag values.

Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

The SVC connection is special and does not belong to neither an
interface or a bundle.

Remove the unused SVC bundle-id define.

Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Remove unused, bogus interface-reset helper.

The interface-reset operation is initiated by the SVC, not the AP.

Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Align the DME-attribute values in the protocol header.

Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Fix two greybus container-of macros that used the pointer name for the
member.

Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Cleanup APBridge sequence only in case of last module plugged-out.
For other modules, unregister cportid is sufficient.

Signed-off-by: Vaibhav Agarwal <vaibhav.agarwal@linaro.org>
Reviewed-by: Mark Greer <mark.greer@animalcreek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Use seperate driver to process GB Audio modules plugged-in.
It'll use helper function register_module to attach itself
to gbaudio-codec driver.

Signed-off-by: Vaibhav Agarwal <vaibhav.agarwal@linaro.org>
Reviewed-by: Mark Greer <mark.greer@animalcreek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

We have single I2S port via APB1 for communication with all
audio modules. Thus, we should register single codec driver
and manage all individual audio modules internally within
this driver.

Signed-off-by: Vaibhav Agarwal <vaibhav.agarwal@linaro.org>
Reviewed-by: Mark Greer <mark.greer@animalcreek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

This converts all drivers to use the gb_connection_get_data() and
gb_connection_set_data() functions to make it a bit more explicit as to
what is going on.

Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Add gb_connection_get_data() and gb_connection_set_data() to get and set
the private data of a connection, instead of "open coding" it
everywhere.

Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Enabling greybus ftrace event causes null pointer access due to
that gb_message to SVC has no Bundle. Fix it by handling this in
the trace header.

Testing Done:
$ echo 1 > /d/tracing/event/greybus/enable
 [002] ...1    54.504426: gb_message_send: greybus:1-svc op=0023 if_id=0 hd_id=0 l=0
 [002] ...1    54.504461: gb_host_device_send: greybus:greybus1 if_id=0 l=8

Signed-off-by: David Lin <dtwlin@google.com>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

There is no reason to use end-to-end flow control for Greybus
audio data connections so disable it and enable Controlled
Segment Dropping (CSD).

Testing Done: Played music using audio modules on an EVT1.5.

CC: Vaibhav Agarwal <vaibhav.agarwal@linaro.org>
CC: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Mark Greer <mgreer@animalcreek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Registering more then one module at same time was not
possible with previous implementation. Also unregistering
of the module was missing leading to many instability issues
when camera module is ejected when camera is still active.

Signed-off-by: Gjorgji Rosikopulos <grosikopulos@mm-sol.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Register the greybus camera driver capabilities operation to the
ara_camera subdevice

Signed-off-by: Jacopo Mondi <jacopo.mondi@linaro.org>
Reviewed-by: Gjorgji Rosikopulos <grosikopulos@mm-sol.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

The operation queries the camera module for its capabilities. The
debugfs interface just prints a hex dump of the binary message.

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Jacopo Mondi <jacopo.mondi@linaro.org>
Reviewed-by: Gjorgji Rosikopulos <grosikopulos@mm-sol.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Reversing the kernel version check for new power supply APIs will
easily allow us to use older kernels with backported power supply APIs
by defining "CORE_OWNS_PSY_STRUCT" in power supply core header

Testing Done:
- Build tested with arche kernel with backported power supply APIs
- Build tested also with current arche kernel to make sure we build with
  3.10 kernels

Signed-off-by: Sandeep Patil <sspatil@google.com>
Reviewed-by: Rui Miguel Silva <rui.silva@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Adding a default timeout may not be representative of every
usecase for gb_loopback. Also, tests may continue to run
on the driver in case of a timeout.

To avoid adding a default timeout, handle SIGINT so that when the user
presses ctrl-c the test are stoped. The user can still specify a timeout
value with the -O option.

Signed-off-by: Axel Haslam <ahaslam@baylibre.com>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Currently in loopback on the async path we issue an operation and then add
a timer to time-out that operation should it fail to complete. Looking at a
backtrace given in its feasible op_async->pending can be true and
del_timer() can run before add_timer() has run. In the callback handler we
already hold gb->mutex. This patch fixes that potential race by ensuring we
hold gb->mutex both when we are adding and when we are removing the
relevant timer.

Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reported-and-tested-by: Axel Haslam <ahaslam@baylibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Currently, when a loopback test completely fail,
loopback will return 4294967295 for every min value.
Return 0 instead of 4294967295 in such case.

Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Reviewed-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

The SVC eject timeout is implementation specific and does not belong in
the protocol header so move it to the svc module.

Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Print an error message when the SVC fails to eject an interface.

Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Reviewed-by: Jeffrey Carlyle <jcarlyle@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Do no export the interface-eject helper, which is only supposed to be
used by core.

Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Reviewed-by: Jeffrey Carlyle <jcarlyle@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Separate interface disable from interface removal.

Disabling an interface means tearing down its control connection and
destroying (i.e. deregistering and releasing) its bundles, while
removing it means deregistering and releasing the interface itself.

This is needed to implement controlled module removal, where the module
interfaces are disabled before being physically ejected.

Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Reviewed-by: Jeffrey Carlyle <jcarlyle@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Rename the interface-initialisation function gb_interface_enable(),
which is more descriptive.

Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Jeffrey Carlyle <jcarlyle@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Move helper to remove all interfaces of a host-device to the svc code
and call it when removing the svc device as this needs to be coordinated
with flushing the SVC work queue.

Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Reviewed-by: Jeffrey Carlyle <jcarlyle@google.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Remove useless global interface spinlock that appeared to protect the
host-device interface list, but really did not as we are doing lock-less
look-ups by relying on the single-threaded SVC workqueue.

Document the locking assumptions.

Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Disable the control connection immediately on any errors during
interface initialisation as there's no need to keep it around for an
interface in an error state.

Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Reviewed-by: Jeffrey Carlyle <jcarlyle@google.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Always register interfaces at hotplug regardless of whether
initialisation succeeded or not.

Even if a module failed to initialise we want it to have a
representation while it is physically present.

Note that the vendor and product-string attribute will read as "(null)"
for now on an interface that failed (early) initialisation.

Also note that the switch route is kept until the interface is finally
removed also on initialisation errors.

Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Reviewed-by: Jeffrey Carlyle <jcarlyle@google.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Immediately free any created bundle structures on interface
initialisation errors.

Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Reviewed-by: Jeffrey Carlyle <jcarlyle@google.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Separate interface initialisation from registration of the interface and
its bundles.

This is a step towards registering also interfaces that failed to
initialise (e.g. a dummy interface).

Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Reviewed-by: Jeffrey Carlyle <jcarlyle@google.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Add interface-route-destroy helper to tear down the route and release
the interface device id.

Note that we currently need to grab a reference to the interface to
prevent it from being deallocated before tearing down the route.

Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Reviewed-by: Jeffrey Carlyle <jcarlyle@google.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>