- Mar 08, 2010
-
-
Mike Turquette authored
New function twl4030_remove_script(u8 flags) takes a script type as defined in twl.h and prevents any script already loaded in that position from running. This is accomplished by programming SEQ_ADD_* to 0x3f, the END_OF_SCRIPT value, where SEQ_ADD_* is determined by flags. (Future) users of this function include OMAP board files for machines facing a race condition between sleep and warm reset. Signed-off-by:
Mike Turquette <mturquette@ti.com> Signed-off-by:
Samuel Ortiz <sameo@linux.intel.com>
-
Magnus Damm authored
Enable the sh_mobile_sdhi mfd driver on SH-Mobile ARM processors. While at it, make CONFIG_TMIO_MMC depend on CONFIG_MFD_SH_MOBILE_SDHI. Signed-off-by:
Magnus Damm <damm@opensource.se> Signed-off-by:
-
Magnus Damm authored
Add MMC_CAP_MMC_HIGHSPEED support to the sh_mobile_sdhi driver. Also, remove type cast and FIXME comment. Signed-off-by:
-
Mark Brown authored
This is the chip default but it's possible the bootloader or OTP will have been configured to a different mode (eg, to provide feedback during startup). Signed-off-by:
Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by:
-
Mark Brown authored
Revision B of the WM831x devices changes the sense of the tristate bit for GPIO configuration, inverting it to become an enable instead. Take account of this in the gpiolib driver. A current sink regulation status bit has also been added in revision B, add a flag indicating if it's present but don't use it yet. This revision also adds an interrupt on key up for the ON pin event which the existing code is able to take advantage of. Signed-off-by:
-
Mark Brown authored
Signed-off-by:
-
Mark Brown authored
wm831x_gpio_direction_output() ignored the state passed into it. Signed-off-by:
-
Magnus Damm authored
This patch adds cell->disable() calls to the tmio-mmc probe() error handling and the remove() function. Signed-off-by:
-
Magnus Damm authored
Remove const from the tmio-mmc platform data hclk V3. This change makes it possible to remove the type cast from the sh_mobile_sdhi driver which is using the clock framework to get the clock rate. Signed-off-by:
-
Magnus Damm authored
This patch changes the tmio_mmc driver to wait 100ms before checking the card detect status. This type of delay is quite common among mmc drivers, it seems that most hardware platforms need to give the hardware some time to settle before checking card availabilty. Hotplug is half-broken without this patch on the sh7724 Ecovec board. Hot insertion seems ok but eject is never detected without this patch. Signed-off-by:
-
Yusuke Goda authored
Enable MMC_CAP_XX support in the tmio_mmc driver if pdata->capabilities is set. Signed-off-by:
Yusuke Goda <goda.yusuke@renesas.com> Signed-off-by:
-
Guennadi Liakhovetski authored
On SuperH platforms the SDHI controller does not produce any command IRQs after a completed IO. This leads to card-detect interrupts staying disabled. Do not disable card-detect interrupts on DATA IRQs. Signed-off-by:
Guennadi Liakhovetski <g.liakhovetski@gmx.de> Signed-off-by:
-
Balaji T K authored
Add base address for generic slave ID0, ID1, ID2 and introduced one more entry to align RTC module number between twl4030 and twl6030 Signed-off-by:
Balaji T K <balajitk@ti.com> Signed-off-by:
-
Moiz Sonasath authored
This patch disables TWL4030/5030 I2C1 adn I2C4(SR) internal pull-up, to use only the external HW resistor >=470 Ohm for the assured functionality in HS mode. While testing the I2C in High Speed mode, it was discovered that without a proper pull-up resistor, there is data corruption during multi-byte transfer. RTC(time_set) test case was used for testing. From the analysis done, it was concluded that ideally we need a pull-up of 1.6k Ohm(recomended) or atleast 470 Ohm or greater for assured performance in HS mode. Signed-off-by:
Moiz Sonasath <m-sonasath@ti.com> Signed-off-by:
Allen Pais <allen.pais@ti.com> Signed-off-by:
-
Denis Turischev authored
Intel Poulsbo (SCH) chipset LPC bridge controller contains several functions. Creating and MFD driver for the LPC bridge controller allows simultaneous use of SMBus and GPIO interfaces on the SCH. Signed-off-by:
Denis Turischev <denis@compulab.co.il> Signed-off-by:
-
Samuel Ortiz authored
For ACPI based systems, we should check for ACPI conflicts when adding the platform devices. The test will always succeed for non ACPI platforms. Signed-off-by: -
Eduardo Valentin authored
Change the typo CONFIG_INPUT_TWL4030_PWBUTTON_MODULE in the twl_has_pwrbutton definition to CONFIG_INPUT_TWL4030_PWRBUTTON_MODULE. Signed-off-by:
Eduardo Valentin <eduardo.valentin@nokia.com> Signed-off-by:
Christoph Egger <siccegge@stud.informatik.uni-erlangen.de> Signed-off-by:
-
Haojian Zhuang authored
Signed-off-by:
Haojian Zhuang <haojian.zhuang@marvell.com> Acked-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by:
-
Haojian Zhuang authored
Use genirq to simplify IRQ handling in 88pm860x. Remove the interface of mask/free IRQs on 88pm860x. All these work is taken by genirq. Update the touchscreen driver of 88pm860x since IRQ handling is changed. Signed-off-by:
-
Joonyoung Shim authored
This patch fixes wrong goto statement for error handling on probe. Signed-off-by:
Myungjoo Ham <myungjoo.ham@samsung.com> Signed-off-by:
Joonyoung Shim <jy0922.shim@samsung.com> Acked-by:
-
Haojian Zhuang authored
Use i2c_dummy in 88pm860x driver to avoid using static in probe function. Signed-off-by:
-
Haojian Zhuang authored
Remove unused definitions. Signed-off-by:
-
Haojian Zhuang authored
MAX8925 is a PMIC that contains charger component Signed-off-by:
-
Haojian Zhuang authored
MAX8925 is a PMIC that contains RTC component. Signed-off-by:
-
Haojian Zhuang authored
Update thread irq handler. Simply the interface of using thread irq. Signed-off-by:
-
Haojian Zhuang authored
Update I2C driver in order to fit all of three I2C components in max8925. Signed-off-by:
-
Mike Turquette authored
Variable remap was incorrectly referencing remap_off for the remap_sleep case when configuring TWL4030 power scripts. Signed-off-by:
-
Mark Brown authored
The WM8994 has 11 GPIO lines. Signed-off-by:
-
Mark Brown authored
The WM8994 is a highly integrated ultra low power audio hub CODEC. Since it includes on-board regulators and GPIOs it is represented as a multi-function device, though the overwhelming majority of the functionality is provided by the ASoC CODEC driver. Signed-off-by:
-
Mark Brown authored
As a separate patch due to the large size. Signed-off-by:
-
Randy Dunlap authored
htc-i2cpld should depend on GPIOLIB, otherwise there are many build errors: drivers/mfd/htc-i2cpld.c:50: error: field 'chip_out' has incomplete type drivers/mfd/htc-i2cpld.c:54: error: field 'chip_in' has incomplete type drivers/mfd/htc-i2cpld.c:243: warning: type defaults to 'int' in declaration of '__mptr' drivers/mfd/htc-i2cpld.c:243: warning: initialization from incompatible pointer type drivers/mfd/htc-i2cpld.c:278: warning: type defaults to 'int' in declaration of '__mptr' drivers/mfd/htc-i2cpld.c:278: warning: initialization from incompatible pointer type drivers/mfd/htc-i2cpld.c:282: warning: type defaults to 'int' in declaration of '__mptr' drivers/mfd/htc-i2cpld.c:282: warning: initialization from incompatible pointer type drivers/mfd/htc-i2cpld.c:315: error: dereferencing pointer to incomplete type drivers/mfd/htc-i2cpld.c:322: warning: type defaults to 'int' in declaration of '__mptr' drivers/mfd/htc-i2cpld.c:322: warning: initialization from incompatible pointer type drivers/mfd/htc-i2cpld.c:467+: error: dereferencing pointer to incomplete type [19X] drivers/mfd/htc-i2cpld.c:490: error: implicit declaration of function 'gpiochip_add' drivers/mfd/htc-i2cpld.c:504: error: implicit declaration of function 'gpiochip_remove' Signed-off-by:
Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by:
-
Christoph Egger authored
The TWL4030_BCI_BATTERY config option originates from a patch to the omap git tree. However inclusion in linux was seemingly rejected and the functionality nears inclusion under a different name so this removes the bits of the old version that made it into the mainline kernel again. Signed-off-by:
-
Linus Walleij authored
This fixes the aged and unreachable debugfs code in the AB3100 OTP driver so that it's (A) reachable and (B) works. Bug detected in parallell by Christoph Egger using VAMOS and Robert P. J. Day by his kernel scanning script. Signed-off-by:
Linus Walleij <linus.walleij@stericsson.com> Cc: Christoph Egger <siccegge@stud.informatik.uni-erlangen.de> Cc: Robert P. J. Day <rpjday@crashcourse.ca> Signed-off-by:
-
Linus Walleij authored
This reintroduces the entropy sampling of the AB3100 IRQ as the IRQF_SAMPLE_RANDOM is going out according to the feature removal schedule. I'm trying to do this the right way then, so CC:ing some random people for a quick review. We add entropy for interrupt events in the AB3100 which are truly random in nature, like external cables being connected, voltages on batteries dropping below certain ranges, ADC triggers or overheating. Signed-off-by:
Matt Mackall <mpm@selenic.com> Signed-off-by:
-
Cory Maccarrone authored
This change introduces a driver for the HTC PLD chip found on some smartphones, such as the HTC Wizard and HTC Herald. It works through the I2C bus and acts as a GPIO extender. Specifically: * it can have several sub-devices, each with its own I2C address * Each sub-device provides 8 output and 8 input pins * The chip attaches to one GPIO to signal when any of the input GPIOs change -- at which point all chips must be scanned for changes This driver implements the GPIOs throught the kernel's GPIO and IRQ framework. This allows any GPIO-servicing drivers to operate on htcpld pins, such as the gpio-keys and gpio-leds drivers. Signed-off-by:
Cory Maccarrone <darkstar6262@gmail.com> Signed-off-by:
-
Haojian Zhuang authored
MAX8925 contains 3 Buck and 20 LDO regulator. Signed-off-by:
-
Haojian Zhuang authored
Enable max8925 backlight sub device. Signed-off-by:
-
Haojian Zhuang authored
Add subdevs in MAX8925. MAX8925 includes regulator, backlight and touch components. Signed-off-by:
-
Haojian Zhuang authored
Basic Max8925 support, which is a power management IC from Maxim Semiconductor. Signed-off-by:
-
Haojian Zhuang authored
Remove the support 88PM8607 A0/A1 stepping. There's some register definition changes in B0 stepping. It can make software more efficient. Signed-off-by:
-
