blob: 35d8275b553be1cc602a6668fb9262a9399b31b8 (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
|
# SPDX-License-Identifier: GPL-2.0-or-later
# script for stm32f4x family
#
# stm32f4 devices support both JTAG and SWD transports.
#
source [find target/swj-dp.tcl]
source [find mem_helper.tcl]
if { [info exists CHIPNAME] } {
set _CHIPNAME $CHIPNAME
} else {
set _CHIPNAME stm32f4x
}
set _ENDIAN little
# Work-area is a space in RAM used for flash programming
# By default use 32kB (Available RAM in smallest device STM32F410)
if { [info exists WORKAREASIZE] } {
set _WORKAREASIZE $WORKAREASIZE
} else {
set _WORKAREASIZE 0x8000
}
#jtag scan chain
if { [info exists CPUTAPID] } {
set _CPUTAPID $CPUTAPID
} else {
if { [using_jtag] } {
# See STM Document RM0090
# Section 38.6.3 - corresponds to Cortex-M4 r0p1
set _CPUTAPID 0x4ba00477
} {
set _CPUTAPID 0x2ba01477
}
}
swj_newdap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID
dap create $_CHIPNAME.dap -chain-position $_CHIPNAME.cpu
if {[using_jtag]} {
jtag newtap $_CHIPNAME bs -irlen 5
}
set _TARGETNAME $_CHIPNAME.cpu
target create $_TARGETNAME cortex_m -endian $_ENDIAN -dap $_CHIPNAME.dap
$_TARGETNAME configure -work-area-phys 0x20000000 -work-area-size $_WORKAREASIZE -work-area-backup 0
set _FLASHNAME $_CHIPNAME.flash
flash bank $_FLASHNAME stm32f2x 0 0 0 0 $_TARGETNAME
flash bank $_CHIPNAME.otp stm32f2x 0x1fff7800 0 0 0 $_TARGETNAME
if { [info exists QUADSPI] && $QUADSPI } {
set a [llength [flash list]]
set _QSPINAME $_CHIPNAME.qspi
flash bank $_QSPINAME stmqspi 0x90000000 0 0 0 $_TARGETNAME 0xA0001000
}
# JTAG speed should be <= F_CPU/6. F_CPU after reset is 16MHz, so use F_JTAG = 2MHz
#
# Since we may be running of an RC oscilator, we crank down the speed a
# bit more to be on the safe side. Perhaps superstition, but if are
# running off a crystal, we can run closer to the limit. Note
# that there can be a pretty wide band where things are more or less stable.
adapter speed 2000
adapter srst delay 100
if {[using_jtag]} {
jtag_ntrst_delay 100
}
reset_config srst_nogate
if {![using_hla]} {
# if srst is not fitted use SYSRESETREQ to
# perform a soft reset
cortex_m reset_config sysresetreq
}
$_TARGETNAME configure -event examine-end {
# Enable debug during low power modes (uses more power)
# DBGMCU_CR |= DBG_STANDBY | DBG_STOP | DBG_SLEEP
mmw 0xE0042004 0x00000007 0
# Stop watchdog counters during halt
# DBGMCU_APB1_FZ |= DBG_IWDG_STOP | DBG_WWDG_STOP
mmw 0xE0042008 0x00001800 0
}
tpiu create $_CHIPNAME.tpiu -dap $_CHIPNAME.dap -ap-num 0 -baseaddr 0xE0040000
lappend _telnet_autocomplete_skip _proc_pre_enable_$_CHIPNAME.tpiu
proc _proc_pre_enable_$_CHIPNAME.tpiu {_chipname} {
targets $_chipname.cpu
if { [$_chipname.tpiu cget -protocol] eq "sync" } {
switch [$_chipname.tpiu cget -port-width] {
1 {
# Set TRACE_IOEN; TRACE_MODE to sync 1 bit; GPIOE[2-3] to AF0
mmw 0xE0042004 0x00000060 0x000000c0
mmw 0x40021020 0x00000000 0x0000ff00
mmw 0x40021000 0x000000a0 0x000000f0
mmw 0x40021008 0x000000f0 0x00000000
}
2 {
# Set TRACE_IOEN; TRACE_MODE to sync 2 bit; GPIOE[2-4] to AF0
mmw 0xE0042004 0x000000a0 0x000000c0
mmw 0x40021020 0x00000000 0x000fff00
mmw 0x40021000 0x000002a0 0x000003f0
mmw 0x40021008 0x000003f0 0x00000000
}
4 {
# Set TRACE_IOEN; TRACE_MODE to sync 4 bit; GPIOE[2-6] to AF0
mmw 0xE0042004 0x000000e0 0x000000c0
mmw 0x40021020 0x00000000 0x0fffff00
mmw 0x40021000 0x00002aa0 0x00003ff0
mmw 0x40021008 0x00003ff0 0x00000000
}
}
} else {
# Set TRACE_IOEN; TRACE_MODE to async
mmw 0xE0042004 0x00000020 0x000000c0
}
}
$_CHIPNAME.tpiu configure -event pre-enable "_proc_pre_enable_$_CHIPNAME.tpiu $_CHIPNAME"
$_TARGETNAME configure -event reset-init {
# Configure PLL to boost clock to HSI x 4 (64 MHz)
mww 0x40023804 0x08012008 ;# RCC_PLLCFGR 16 Mhz /8 (M) * 128 (N) /4(P)
mww 0x40023C00 0x00000102 ;# FLASH_ACR = PRFTBE | 2(Latency)
mmw 0x40023800 0x01000000 0 ;# RCC_CR |= PLLON
sleep 10 ;# Wait for PLL to lock
mmw 0x40023808 0x00001000 0 ;# RCC_CFGR |= RCC_CFGR_PPRE1_DIV2
mmw 0x40023808 0x00000002 0 ;# RCC_CFGR |= RCC_CFGR_SW_PLL
# Boost JTAG frequency
adapter speed 8000
}
$_TARGETNAME configure -event reset-start {
# Reduce speed since CPU speed will slow down to 16MHz with the reset
adapter speed 2000
}
|
