1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
|
# This is a STM32L4R9I discovery board with a single STM32L4R9AII6 chip.
# http://www.st.com/en/evaluation-tools/32l4r9idiscovery.html
# This is for using the onboard STLINK
source [find interface/stlink.cfg]
transport select hla_swd
# increase working area to 96KB
set WORKAREASIZE 0x18000
# enable stmqspi
set OCTOSPI1 1
set OCTOSPI2 0
source [find target/stm32l4x.cfg]
# OCTOSPI initialization
# octo: 8-line mode
proc octospi_init { octo } {
global a b
mmw 0x4002104C 0x001001FF 0 ;# RCC_AHB2ENR |= OSPIMEN, GPIOAEN-GPIOIEN (enable clocks)
mmw 0x40021050 0x00000300 0 ;# RCC_AHB3ENR |= OSPI2EN, OSPI1EN (enable clocks)
mmw 0x40021058 0x10000000 0 ;# RCC_APB1ENR1 |= PWREN (enable clock)
sleep 1 ;# Wait for clock startup
mmw 0x40007004 0x00000200 0 ;# PWR_CR2 |= IOSV (required for use of GPOIG, cf. RM0432)
mww 0x50061C04 0x00000000 ;# OCTOSPIM_P1CR: disable Port 1
mww 0x50061C08 0x03010111 ;# OCTOSPIM_P2CR: assign Port 2 to OCTOSPI1
# PG12: P2_NCS, PI06: P2_CLK, PG15: P2_DQS, PG10: P2_IO7, PG09: P2_IO6, PH10: P2_IO5,
# PH09: P2_IO4, PH08: P2_IO3, PI09: P2_IO2, PI10: P2_IO1, PI11: P2_IO0
# PG15:AF05:V, PG12:AF05:V, PG10:AF05:V, PG09:AF05:V, PH10:AF05:V, PH09:AF05:V
# PH08:AF05:V, PI11:AF05:V, PI10:AF05:V, PI09:AF05:V, PI06:AF05:V
# Port G: PG15:AF05:V, PG12:AF05:V, PG10:AF05:V, PG09:AF05:V
mmw 0x48001800 0x82280000 0x41140000 ;# MODER
mmw 0x48001808 0xC33C0000 0x00000000 ;# OSPEEDR
mmw 0x48001824 0x50050550 0xA00A0AA0 ;# AFRH
# Port H: PH10:AF05:V, PH09:AF05:V, PH08:AF05:V
mmw 0x48001C00 0x002A0000 0x00150000 ;# MODER
mmw 0x48001C08 0x003F0000 0x00000000 ;# OSPEEDR
mmw 0x48001C24 0x00000555 0x00000AAA ;# AFRH
# Port I: PI11:AF05:V, PI10:AF05:V, PI09:AF05:V, PI06:AF05:V
mmw 0x48002000 0x00A82000 0x00541000 ;# MODER
mmw 0x48002008 0x00FC3000 0x00000000 ;# OSPEEDR
mmw 0x48002020 0x05000000 0x0A000000 ;# AFRL
mmw 0x48002024 0x00005550 0x0000AAA0 ;# AFRH
# OCTOSPI1: memory-mapped 1-line read mode with 4-byte addresses
mww 0xA0001130 0x00001000 ;# OCTOSPI_LPTR: deactivate CS after 4096 clocks when FIFO is full
mww 0xA0001000 0x3040000B ;# OCTOSPI_CR: FMODE=0x1, APMS=1, FTHRES=0, FSEL=0, DQM=0, TCEN=0
mww 0xA0001008 0x01190100 ;# OCTOSPI_DCR1: MTYP=0x1, FSIZE=0x19, CSHT=0x01, CKMODE=0, DLYBYP=0
mww 0xA000100C 0x00000001 ;# OCTOSPI_DCR2: PRESCALER=1
mww 0xA0001108 0x00000000 ;# OCTOSPI_TCR: SSHIFT=0, DHQC=0, DCYC=0x0
mww 0xA0001100 0x01003101 ;# OCTOSPI_CCR: DMODE=0x1, ABMODE=0x0, ADSIZE=0x3, ADMODE=0x1, ISIZE=0x0, IMODE=0x1
mww 0xA0001110 0x00000013 ;# OCTOSPI_IR: INSTR=READ4B
if { $octo == 1 } {
stmqspi cmd $a 1 0x71 0x00 0x00 0x00 0x00 ;# Read Conf. Reg. 2, addr 0x00000000: DOPI, SOPI bits
stmqspi cmd $a 0 0x06 ;# Write Enable
stmqspi cmd $a 1 0x05 ;# Read Status Register
stmqspi cmd $a 0 0x72 0x00 0x00 0x00 0x00 0x02 ;# Write Conf. Reg. 2, addr 0x00000000: DTR OPI enable
# OCTOSPI1: memory-mapped 8-line read mode with 4-byte addresses
mww 0xA0001000 0x3040000B ;# OCTOSPI_CR: FMODE=0x3, APMS=1, FTHRES=0, FSEL=0, DQM=0, TCEN=1, EN=1
mww 0xA0001108 0x10000006 ;# OCTOSPI_TCR: SSHIFT=0, DHQC=1, DCYC=0x6
mww 0xA0001100 0x2C003C1C ;# OCTOSPI_CCR: DTR, DMODE=0x4, ABMODE=0x0, ADSIZE=0x3, ADMODE=0x4, ISIZE=0x1, IMODE=0x4
mww 0xA0001110 0x0000EE11 ;# OCTOSPI_IR: INSTR=OCTA DTR Read
flash probe $a ;# reload configuration from CR, TCR, CCR, IR register values
stmqspi cmd $a 0 0x06 ;# Write Enable
stmqspi cmd $a 1 0x05 0x00 0x00 0x00 0x00 ;# Read Status Register (note dummy address in 8-line mode)
stmqspi cmd $a 0 0x04 ;# Write Disable
stmqspi cmd $a 1 0x05 0x00 0x00 0x00 0x00 ;# Read Status Register (note dummy address in 8-line mode)
stmqspi cmd $a 1 0x71 0x00 0x00 0x00 0x00 ;# Read Conf. Reg. 2, addr 0x00000000: DOPI, SOPI bits
}
}
$_TARGETNAME configure -event reset-init {
mmw 0x40022000 0x00000003 0x0000000C ;# 3 WS for 72 MHz HCLK
sleep 1
mmw 0x40021000 0x00000100 0x00000000 ;# HSI on
mww 0x4002100C 0x01002432 ;# RCC_PLLCFGR 72 MHz: PLLREN=1, PLLM=4, PLLN=36, PLLR=2, HSI
mww 0x40021008 0x00008001 ;# always HSI, APB1: /1, APB2: /1
mmw 0x40021000 0x01000000 0x00000000 ;# PLL on
sleep 1
mmw 0x40021008 0x00000003 0x00000000 ;# switch to PLL
sleep 1
adapter speed 4000
octospi_init 1
}
|
