blob: 5c4714e199652200265ae7477944bf7f85d67d7d (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
|
################################################################################
# Olimex SAM9-L9260 Development Board
#
# http://www.olimex.com/dev/sam9-L9260.html
#
# Atmel AT91SAM9260 : PLLA = 198.656 MHz, MCK = 99.328 MHz
# PMC configured for external 18.432 MHz crystal
#
# 32-bit SDRAM : 2 x Samsung K4S561632J-UC75, 4M x 16Bit x 4 Banks
# 8-bit NAND Flash : 1 x Samsung K9F4G08U0M, 512M x 8Bit
# Dataflash : 1 x Atmel AT45DB161D, 16Mbit
#
################################################################################
source [find target/at91sam9260.cfg]
# NTRST_E jumper is enabled by default, so we don't need to override the reset
# config.
#reset_config srst_only
$_TARGETNAME configure -event reset-start {
# At reset, CPU runs at 32.768 kHz. JTAG frequency must be 6 times slower if
# RCLK is not supported.
jtag_rclk 5
halt
# RSTC_MR : enable user reset, reset length is 64 slow clock cycles. MMU may
# be enabled... use physical address.
mww phys 0xfffffd08 0xa5000501
}
$_TARGETNAME configure -event reset-init {
mww 0xfffffd44 0x00008000 # WDT_MR : disable watchdog
##
# Clock configuration for 99.328 MHz main clock.
##
mww 0xfffffc20 0x00004001 # CKGR_MOR : enable main oscillator, 512 slow clock startup
sleep 20 # wait 20 ms (need 15.6 ms for startup)
mww 0xfffffc30 0x00000001 # PMC_MCKR : switch to main oscillator (18.432 MHz)
sleep 10 # wait 10 ms
mww 0xfffffc28 0x2060bf09 # CKGR_PLLAR : 18.432 MHz / 9 * 97 = 198.656 MHz, 63 slow clock startup
sleep 20 # wait 20 ms (need 1.9 ms for startup)
mww 0xfffffc30 0x00000101 # PMC_MCKR : no scale on proc clock, master is proc / 2
sleep 10 # wait 10 ms
mww 0xfffffc30 0x00000102 # PMC_MCKR : switch to PLLA (99.328 MHz)
# Increase JTAG speed to 6 MHz if RCLK is not supported.
jtag_rclk 6000
arm7_9 dcc_downloads enable # Enable faster DCC downloads.
##
# SDRAM configuration for 2 x Samsung K4S561632J-UC75, 4M x 16Bit x 4 Banks.
##
mww 0xfffff870 0xffff0000 # PIOC_ASR : select peripheral function for D15..D31
mww 0xfffff804 0xffff0000 # PIOC_PDR : disable PIO function for D15..D31
mww 0xffffef1c 0x00010002 # EBI_CSA : assign EBI CS1 to SDRAM, VDDIOMSEL set for +3V3 memory
mww 0xffffea08 0x85237259 # SDRAMC_CR : configure SDRAM for Samsung chips
mww 0xffffea00 0x1 # SDRAMC_MR : issue NOP command
mww 0x20000000 0
mww 0xffffea00 0x2 # SDRAMC_MR : issue an 'All Banks Precharge' command
mww 0x20000000 0
mww 0xffffea00 0x4 # SDRAMC_MR : issue 8 x 'Auto-Refresh' command
mww 0x20000000 0
mww 0xffffea00 0x4
mww 0x20000000 0
mww 0xffffea00 0x4
mww 0x20000000 0
mww 0xffffea00 0x4
mww 0x20000000 0
mww 0xffffea00 0x4
mww 0x20000000 0
mww 0xffffea00 0x4
mww 0x20000000 0
mww 0xffffea00 0x4
mww 0x20000000 0
mww 0xffffea00 0x4
mww 0x20000000 0
mww 0xffffea00 0x3 # SDRAMC_MR : issue a 'Load Mode Register' command
mww 0x20000000 0
mww 0xffffea00 0x0 # SDRAMC_MR : normal mode
mww 0x20000000 0
mww 0xffffea04 0x2b6 # SDRAMC_TR : set refresh timer count to 7 us
}
|
