blob: 645b1a7bd098b905883674491d738da7af3dc21f (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
|
################################################################################
# Atmel AT91SAM9263-EK eval board
################################################################################
source [find mem_helper.tcl]
source [find target/at91sam9263.cfg]
uplevel #0 [list source [find chip/atmel/at91/hardware.cfg]]
uplevel #0 [list source [find chip/atmel/at91/at91sam9263.cfg]]
uplevel #0 [list source [find chip/atmel/at91/at91sam9263_matrix.cfg]]
uplevel #0 [list source [find chip/atmel/at91/at91sam9_init.cfg]]
# By default S1 is open and this means that NTRST is not connected.
# The reset_config in target/at91sam9263.cfg is overridden here.
# (or S1 must be populated with a 0 Ohm resistor)
reset_config srst_only
scan_chain
$_TARGETNAME configure -event gdb-attach { reset init }
$_TARGETNAME configure -event reset-init { at91sam9263ek_reset_init }
$_TARGETNAME configure -event reset-start { at91sam9_reset_start }
proc at91sam9263ek_reset_init { } {
set config(master_pll_div) 14
set config(master_pll_mul) 171
set val [expr $::AT91_WDT_WDV] ;# Counter Value
set val [expr ($val | $::AT91_WDT_WDDIS)] ;# Watchdog Disable
set val [expr ($val | $::AT91_WDT_WDD)] ;# Delta Value
set val [expr ($val | $::AT91_WDT_WDDBGHLT)] ;# Debug Halt
set val [expr ($val | $::AT91_WDT_WDIDLEHLT)] ;# Idle Halt
set config(wdt_mr_val) $val
set config(sdram_piod) 1
;# EBI_CSA, no pull-ups for D[15:0], CS1 SDRAM, CS3 NAND Flash
set config(matrix_ebicsa_addr) $::AT91_MATRIX_EBI0CSA
set val [expr $::AT91_MATRIX_EBI0_DBPUC]
set val [expr ($val | $::AT91_MATRIX_EBI0_VDDIOMSEL_3_3V)]
set val [expr ($val | $::AT91_MATRIX_EBI0_CS1A_SDRAMC)]
set config(matrix_ebicsa_val) $val
;# SDRAMC_CR - Configuration register
set val [expr $::AT91_SDRAMC_NC_9]
set val [expr ($val | $::AT91_SDRAMC_NR_13)]
set val [expr ($val | $::AT91_SDRAMC_NB_4)]
set val [expr ($val | $::AT91_SDRAMC_CAS_3)]
set val [expr ($val | $::AT91_SDRAMC_DBW_32)]
set val [expr ($val | (1 << 8))] ;# Write Recovery Delay
set val [expr ($val | (7 << 12))] ;# Row Cycle Delay
set val [expr ($val | (2 << 16))] ;# Row Precharge Delay
set val [expr ($val | (2 << 20))] ;# Row to Column Delay
set val [expr ($val | (5 << 24))] ;# Active to Precharge Delay
set val [expr ($val | (1 << 28))] ;# Exit Self Refresh to Active Delay
set config(sdram_cr_val) $val
set config(sdram_tr_val) 0x13c
set config(sdram_base) $::AT91_CHIPSELECT_1
at91sam9_reset_init $config
}
|
