aboutsummaryrefslogtreecommitdiff
path: root/tcl/board
AgeCommit message (Collapse)AuthorFilesLines
2020-11-15flash/stm32l4x: STM32L55/L56xx basic support (non-secure mode)Tarek BOCHKATI1-0/+13
STM32L5 have 512 Kbytes of Flash memory with dual bank architecture. STM32L5 flash is quite similar to L4 flash, mainly register names and offsets and some bits are changed. NON-SECURE flash is located at 0x8000000 like L4 devices, so no big change is needed (secure flash will be subject of another change). Note: flash driver name is set stm32l5x, in order to extend the commands with specific L5 commands (to manage TZEN for example ...) Note: this works only when TZEN=0 Change-Id: Ie758abb4aa19a3f29eeb0702d7dcb43992e4c639 Signed-off-by: Michael Jung <mijung@gmx.net> Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com> Reviewed-on: http://openocd.zylin.com/5510 Tested-by: jenkins Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com> Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
2020-11-15tcl/board: rename board file ST b-l475e-iot01aAntonio Borneo1-0/+2
Use the board file name as <company>_<name>.cfg Add the SPDX tag to workaround an error in checkpatch that fails to recognize as valid a patch that only changes a file name. Change-Id: I929cd9e5f9fe2e7386950643487534c9a5a05bc6 Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com> Fixes: e44539d66c89 ("Flash, FRAM and EEPROM driver for STM32 QUAD-/OCTOSPI interface") Reviewed-on: http://openocd.zylin.com/5931 Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com> Tested-by: jenkins
2020-11-08Flash, FRAM and EEPROM driver for STM32 QUAD-/OCTOSPI interfaceAndreas Bolsch17-0/+1414
- write speed up to 150 kByte/s on STM32F469I-disco (due to SWD clock and USB connection), up to 1 MByte/s on Nucleo-F767ZI with external STLink-V3 or Nucleo-G474RE with two W25Q256FV in dual 4-line mode or STM32H73BI-Disco in octal mode - tested with STM32L476G-disco (64MBit flash, 3-byte addr), STM32F412G-Disco, STM32F469I-Disco, STM32F746G-Disco, and STM32L476G-Disco (all 128Mbit flash, 3-byte addr), STM32F723E-Disco, STM32F769I-Disco (512Mbit flash, 4-byte addr) STM32L4R9I-Disco, STM32L4P5G-Disco (512MBit octo-flash, DTR, 4-byte addr) STM32H745I-Disco, STM32H747I-Disco (two 512MBit flash, 4-byte addr) STM32H73BI-Disco, STM32H735G-Disco (512MBit octo-flash, DTR, 4-byte addr) - suitable cfg for Discovery boards included - limited parsing of SFDP data if flash device not hardcoded (tested only in single/quad mode as most devices either don't support SFDP at all or have empty(!) SFDP memory) - 'set' command for auto detection override (e. g. for EEPROMs) - 'cmd' command for arbitrary SPI commands (reconfiguration, testing etc.) - makefile for creation of binary loader files - tcl/board/stm32f469discovery.cfg superseded by stm32f469i-disco.cfg - tcl/board/stm32f7discovery.cfg removed as name is ambiguous (superseded by stm32f746g-disco.cfg vs. stm32f769i-disco.cfg) - dual 4-line mode tested on Nucleo-F767ZI, Nucleo-H743ZI and Nucleo-H7A3ZI-Q with two W25Q256FV, and on Nucleo-L496ZP-P and Nucleo-L4R5ZI with two W25Q128FV, sample cfg files included and on STM32H745I-Disco, STM32H747I-Disco, STM32H750B-Disco - read/verify/erase_check uses indirect read mode to work around silicon bug in H7, L4+ and MP1 memory mapped mode (last bytes not readable, accessing last bytes causes debug interface to hang) - octospi supported only in single/dual 1-line, 2-line, 4-line and single 8-line modes, (not in hyper flash mode) Requirements: GPIOs must be initialized appropriately, and SPI flash chip be configured appropriately (1-line ..., QPI, 4-byte addresses ...). This is board/chip specific, cf. included cfg files. The driver infers most parameters from current setting in CR, CCR, ... registers. Change-Id: I54858fbbe8758c3a5fe58812e93f5f39514704f8 Signed-off-by: Andreas Bolsch <hyphen0break@gmail.com> Reviewed-on: http://openocd.zylin.com/4321 Tested-by: jenkins Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com> Reviewed-by: Tomas Vanek <vanekt@fbl.cz> Reviewed-by: Christopher Head <chead@zaber.com>
2020-10-30tcl/board: fix changed target config filenamesAntonio Borneo2-2/+2
In commit a1ce28b118e7 ("rename some target scripts to be consistent with the rest") the following renames was applied, but the old names are still referenced: tcl/target/{sam7se512.cfg => at91sam7se512.cfg} tcl/target/{sam7x256.cfg => at91sam7x256.cfg} Fix the board files to use to correct target config filename. Change-Id: I7698aa0da7db95c2bd9ba7ab8c260905a975c857 Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com> Reviewed-on: http://openocd.zylin.com/5888 Reviewed-by: Tomas Vanek <vanekt@fbl.cz> Tested-by: jenkins
2020-10-30tcl/board: drop 'tcl' prefix in 'find' commandAntonio Borneo2-2/+2
When OpenOCD is installed to the host the 'tcl' folder gets usually installed in /usr/share/openocd/, thus having 'tcl' as prefix of the target's file causes 'find' to fail. Remove the 'tcl' folder prefix. Change-Id: I3dc484c8de6af8f5aae4dd1b230522ee47ae2ba6 Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com> Reviewed-on: http://openocd.zylin.com/5887 Reviewed-by: Tomas Vanek <vanekt@fbl.cz> Tested-by: jenkins
2020-10-30board: drop open-bldcKarl Palsson1-7/+0
This is a) broken and b) doesn't include anything other than the (broken) target alias. Don't see any reason for it to exist. Change-Id: I833635eeac392bf7c0c39f51ff2f76525ba2d406 Signed-off-by: Karl Palsson <karlp@tweak.net.au> Reviewed-on: http://openocd.zylin.com/5884 Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com> Tested-by: jenkins Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
2020-10-03tcl: board/dp_busblaster_v4 Busblaster v4.1a by Seed Studio addedUlrich-Lorenz Schlüter1-0/+19
Change-Id: I53141d7f6f022f9dee641858f5fb0e0b70c049f8 Signed-off-by: Paul Fertser <fercerpav@gmail.com> Signed-off-by: Ulrich-Lorenz Schlüter <audiomobster@gmail.com> Reviewed-on: http://openocd.zylin.com/5549 Tested-by: jenkins Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
2020-10-03tcl/board: Add QuickLogic QuickFeather configurationJan Kowalewski1-0/+9
Add configuration for QuickLogic QuickFeather development kit. Change-Id: I39120714bf0bcafa86e0071c38da84a7d9f12a0d Signed-off-by: Jan Kowalewski <jkowalewski@antmicro.com> Reviewed-on: http://openocd.zylin.com/5803 Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com> Tested-by: jenkins
2020-09-05tcl/board/st_nucleo_l1.cfg use dualbank configurationAlexandre Bourdiol1-1/+1
st_nucleo_l1.cfg is based on STM32L152RET6 which support dualbank flash. Change-Id: I7ecdb7b7557229465e23eed667f20cd84197dfc7 Signed-off-by: Alexandre Bourdiol <alexandre.bourdiol@st.com> Reviewed-on: http://openocd.zylin.com/5829 Tested-by: jenkins Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com> Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
2020-08-16tcl: Add support for NDS V5 target and xc7/Corvette-F1Hellosun Wu2-0/+23
The "Corvette-F1" is an Arduino-compatible evaluation platform, which fully supports AndesCore. The board has FTDI FT2232 to connected to FPGA's JTAG interface. The "ADP-XC7KFF676" is a development and prototyping board that provides capacity for evaluation of AndesCore processors. It works with AICE in-circuit debugging tools. This patch also include target/nds32v5.cfg to support AndesCore N22/N25F and AndeShape Platform AE250. Change-Id: I144d5063d5086d00ec44634a5028b5ea5d2eba33 Signed-off-by: Hellosun Wu <wujiheng.tw@gmail.com> Reviewed-on: http://openocd.zylin.com/5338 Tested-by: jenkins Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
2020-07-26Introduce tcl config files for Synopsys HSDK boardEvgeniy Didin1-0/+18
With this commit we add tcl configure files for ARCv2 HS Development kit(HSDK). HSDK board has Quad-core ARC HS38 CPU with L1 and L2 caches. Change-Id: I372ef45428c7c7ca1421a6da3e5ed08b86f705e0 Signed-off-by: Evgeniy Didin <didin@synopsys.com> Reviewed-on: http://openocd.zylin.com/5784 Tested-by: jenkins Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
2020-06-14board: Add the HiFive1 revB board configurationAlistair Francis1-0/+21
Change-Id: If186afcfd2c87414b9323569a16aed9a6054c883 Signed-off-by: Alistair Francis <alistair.francis@wdc.com> Reviewed-on: http://openocd.zylin.com/5680 Tested-by: jenkins Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com> Reviewed-by: Tim Newsome <tim@sifive.com>
2020-06-06tcl/boards: Rename 'ek-tm4c1294xl.cfg' to 'ti_ek-tm4c1294xl.cfg'Marc Schink2-13/+16
The new filename has a proper vendor prefix. Keep the old configuration file for now but show a "deprecated" warning at runtime. Change-Id: If7465a752f47f3292e430c8b311148badfd384cd Signed-off-by: Marc Schink <dev@zapb.de> Reviewed-on: http://openocd.zylin.com/5478 Tested-by: jenkins Reviewed-by: Karl Palsson <karlp@tweak.net.au> Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
2020-06-06tcl/boards: Rename 'ek-tm4c123gxl.cfg' to 'ti_ek-tm4c123gxl.cfg'Marc Schink2-12/+15
The new filename has a proper vendor prefix. Keep the old configuration file for now but show a "deprecated" warning at runtime. Change-Id: I13871ec13709055843e23b1b6da90694fd60505e Signed-off-by: Marc Schink <dev@zapb.de> Reviewed-on: http://openocd.zylin.com/5477 Tested-by: jenkins Reviewed-by: Karl Palsson <karlp@tweak.net.au> Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
2020-06-06tcl/boards: Rename 'dk-tm4c129.cfg' to 'ti_dk-tm4c129.cfg'Marc Schink2-13/+16
The new filename has a proper vendor prefix. Keep the old configuration file for now but show a "deprecated" warning at runtime. Change-Id: I30fcb8f291d401acaa1fe665db0eeabc250d24b6 Signed-off-by: Marc Schink <dev@zapb.de> Reviewed-on: http://openocd.zylin.com/5476 Tested-by: jenkins Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com> Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
2020-05-24tcl/board: add board ST nucleo-8l152r8Antonio Borneo1-0/+10
The transport SWIM is selected twice, in board and in target, thus a warning is generated at run-time. It should be fixed by remove a line in the target file, but does not harm so let's keep it there for the time being. Change-Id: I479004dc16005a330d552c8dbd5def61690f9b9f Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com> Reviewed-on: http://openocd.zylin.com/5543 Tested-by: jenkins
2020-05-09tcl: remove trailing whitespaceAntonio Borneo13-110/+110
The script checkpatch available in new Linux kernel offers an experimental feature for automatically fix the code in place. While still experimental, the feature works quite well for simple fixes, like spacing. This patch has been created automatically with the script under review for inclusion in OpenOCD, using the command: find tcl/ -type f -exec ./tools/scripts/checkpatch.pl \ -q --types TRAILING_WHITESPACE --fix-inplace -f {} \; The patch only changes amount and position of whitespace, thus the following commands show empty diff git diff -w git log -w -p git log -w --stat Change-Id: Ie7e3a236f4db9c70019e3b3c7e851edbd3a9dd84 Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com> Reviewed-on: http://openocd.zylin.com/5616 Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com> Tested-by: jenkins
2020-05-09tcl: fix typo and spellingAntonio Borneo18-19/+19
Identified by checkpatch script from Linux kernel v5.7-rc1 using the command find tcl/ -type f -exec ./tools/scripts/checkpatch.pl \ -q --types TYPO_SPELLING --strict -f {} \; Change-Id: I7b523f0ab5ec047ff167742a44c29984ac672cf4 Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com> Reviewed-on: http://openocd.zylin.com/5615 Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com> Tested-by: jenkins
2020-05-02coding style: tcl: remove empty lines at end of text filesAntonio Borneo38-47/+0
Empty lines at end of text files are useless. Remove them. Change-Id: I503cb0a96c7ccb132f4486c206a48831121d7abd Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com> Reviewed-on: http://openocd.zylin.com/5171 Tested-by: jenkins
2020-04-21jtag/drivers: add debugging support for Mellanox BlueField SoCLiming Sun1-0/+6
This commits adds debugging support for the Mellanox BlueField SoC via rshim, which is an interface accessible from external USB or PCIe (for SmartNIC case) via the rshim driver. It implements the arm dap interfaces based on the existing dapdirect framework. Change-Id: I18eb1c54293ec2c581f853e0e55b3f96d7978b56 Signed-off-by: Liming Sun <lsun@mellanox.com> Reviewed-on: http://openocd.zylin.com/5457 Tested-by: jenkins Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
2020-04-21tcl/target: Drop reference to renesas_gen2_common.cfgMarek Vasut3-3/+0
Drop bogus reference to board/renesas_gen2_common.cfg , which is a non-existing file. Fixes: a01474bb4c4c ("tcl/target: Switch Renesas R-Car Gen2 boards to new config") Change-Id: Icb22d8456b7ac94d3a9a4ed354b246ee1332b122 Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Reviewed-on: http://openocd.zylin.com/5564 Tested-by: jenkins Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
2020-04-21tcl: stm32mp15x: add target and board config filesAntonio Borneo1-0/+11
The stm32mp15x has one or two Cortex-A7 (depending on the P/N) and one Cortex-M4. The second core is automatically detected by the target script. In "engineering boot" all the cores are accessible. In "production boot" the Cortex-M4 is kept in reset state after power-on or NRST. The board DK2 includes a ST-Link/V2, but only SWD is connected. Change-Id: Ib6ebefcc696b1716e0f98694cadf0b04fd7d11d6 Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com> Reviewed-on: http://openocd.zylin.com/5454 Tested-by: jenkins Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
2020-04-20Introduce ARCv2 tcl config filesEvgeniy Didin4-0/+87
With this commit we add tcl files which describes ARCv2 architecture features and configure files for ARCv2 EMSK board. Changes since v1: -Moved from http://openocd.zylin.com/#/c/5332/4 into separate commit. Changes: 22.01.2020: -Removed "actionpoints" handling code in tcl/cpu/arc/v2.tcl because this capability is not supported yet. Changes: 17.03.2020: -Update Licence headers -Cleanup indents -Removed "reset halt" in boards .tcl -Updated adapter frequency commands Changes: 15.03.2020: -Removed "init" in the of boards .tcl Change-Id: I51bf620abe7b8e046e1dccc861a7d963965d3a42 Signed-off-by: Evgeniy Didin <didin@synopsys.com> Cc: Alexey Brodkin <abrodkin@synopsys.com> Reviewed-on: http://openocd.zylin.com/5350 Tested-by: jenkins Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
2020-03-24tcl/target: Enable using vectreset for CC3320SF targetsEdward Fewell2-0/+4
On CC32xx family of devices, sysrequest is disabled, and vectreset is blocked by the boot loader (stops in a while(1) statement). srst reset can leave the target in a state that prevents debug. This change enables using vectreset on SF variants by moving the PC to the start of the user application in internal flash. This allows for a more reliable reset, but with two caveats: 1) This only works for the SF variant with internal flash. 2) This only resets the CPU and not any peripherals. Tested on CC3220SF rev B Launchpad in both SWD and JTAG modes. Confirmed proper behavior of reset, reset init, reset halt, and reset run commands. Update: reworked per comment in code review. Re-tested with CC3220SF Launchpad as both CC3220SF and as CC32xx board to confirm reset behavior as expected. Update: Added adapter srst delay 1100 line to the CC3200 LaunchXL configuration file. Change-Id: Ibc042d785c846c2223ae55b8f2410b75ed2df354 Signed-off-by: Edward Fewell <efewell@ti.com> Reviewed-on: http://openocd.zylin.com/5489 Tested-by: jenkins Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
2020-03-24drivers: xds110: Add support TCK changes in firmware updateEdward Fewell7-7/+7
Starting with XDS110 firmware version 3.0.0.0, the peak TCK frequency became 14,000 kHz. So the delay count calculation in the current driver has been updated to use the new formula for setting the TCK speed depending on which version of the firmware is detected. And because of the changes, the default TCK settings for the XDS110 based Launchpads can be adjusted to take advantage of the higher TCK performance. Note that the values used have been determined through testing in the automated test labs to be the highest TCK frequency with the XDS110 that are still reliable. Different boards have a different peak TCK setting that should be safe. Change-Id: I4d66e90d8fac8272641ba4db4a3a510e3b444d86 Signed-off-by: Edward Fewell <efewell@ti.com> Reviewed-on: http://openocd.zylin.com/5493 Tested-by: jenkins Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
2020-03-09tcl/target: Unify Renesas R-Car JTAG reset configMarek Vasut2-28/+0
Both Gen2 and Gen3 used the same init_reset{} implementation, pull it into common file and include it from both generations. Moreover, this behavior is SoC specific, not board specific, so move the common init_reset into target/ directory. Change-Id: I5489a4bff9a786da8cb7fd7a515b0c9ce9dc16e3 Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Reviewed-on: http://openocd.zylin.com/5400 Tested-by: jenkins Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
2020-03-07bluenrg-x: added support for BlueNRG-LP deviceluca vinci1-0/+3
Extended bluenrg-x flash driver with BlueNRG-LP flash controller. Changes include: - register set for the flash controller - made software structure prone to support more easily future devices - updated target config file Change-Id: I2e2dc70db32cf98c62e3a43f2e44a4600a25ac5b Signed-off-by: luca vinci <luca.vinci@st.com> Reviewed-on: http://openocd.zylin.com/5343 Tested-by: jenkins Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
2020-03-02tcl/target: Switch Renesas R-Car Gen2 boards to new configMarek Vasut3-3/+6
Switch Renesas R-Car Gen2 boards which are currently supported from the old ad-hoc SoC configuration to the new unified configuration. Change-Id: I8a67bceb3ae92d840ae4dbac20868c75e83f7d58 Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Reviewed-on: http://openocd.zylin.com/5398 Tested-by: jenkins Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
2020-02-24coding style: add newline at end of text filesAntonio Borneo3-3/+3
Some text file is missing newline at EOF. Add it. Change-Id: Ieebc790096f40961283c644642e56fde975e957f Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com> Reviewed-on: http://openocd.zylin.com/5167 Tested-by: jenkins
2020-02-23tcl/board: update ST NUCLEO-H745ZI-Q configuration file to use dapdirectTarek BOCHKATI1-7/+5
this board embeds and STLINK DAP capable firmware Change-Id: I276e9f44ad6cf7d1ff664898bbc884676bdbc967 Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com> Reviewed-on: http://openocd.zylin.com/5316 Reviewed-by: Tomas Vanek <vanekt@fbl.cz> Tested-by: jenkins Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
2020-02-23tcl/board: Add imx8mp-evkLeonard Crestez1-0/+15
Board includes an internal adapter (interface/ftdi/imx8mp-evk.cfg) and a standard external ARM-10 connector. Change-Id: Ibb301011665b1edfb95be1213d8100143f6839dd Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com> Reviewed-on: http://openocd.zylin.com/5427 Tested-by: jenkins Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
2020-02-08tcl: Remove executable bitMarc Schink2-0/+0
Change-Id: Ib452435b13c3cb8d14453d983151936238b9601d Signed-off-by: Marc Schink <dev@zapb.de> Reviewed-on: http://openocd.zylin.com/5419 Reviewed-by: Paul Fertser <fercerpav@gmail.com> Tested-by: Paul Fertser <fercerpav@gmail.com> Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
2020-02-06tcl: fix remaining scripts after rework adapter commandsAntonio Borneo1-1/+1
Some script have been added or modified after the patches for reworking the adapter commands were pushed in gerrit. Such scripts use the old command syntax and trigger a "deprecated" warning at runtime. Fix them with the same sed commands used for the other scripts: sed -i 's/^interface /adapter driver /' $(find tcl/ -type f) sed -i 's/adapter_khz/adapter speed/g' $(find tcl/ -type f) sed -i 's/adapter_nsrst_delay/adapter srst delay/g' $(find tcl/ -type f) sed -i 's/adapter_nsrst_assert_width/adapter srst pulse_width/g' $(find tcl/ -type f) Change-Id: I0824d6c506a9af3eb9129b74c02a92b4eb1b100d Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com> Reviewed-on: http://openocd.zylin.com/5424 Reviewed-by: Oleksij Rempel <linux@rempel-privat.de> Tested-by: jenkins
2020-01-29tcl: replace the deprecated commands with "adapter ..."Antonio Borneo93-133/+133
Avoid annoying "deprecated" messages while running the scripts distributed with OpenOCD code. Change automatically created with commands sed -i 's/adapter_khz/adapter speed/g' $(find tcl/ -type f) sed -i 's/adapter_nsrst_delay/adapter srst delay/g' $(find tcl/ -type f) sed -i 's/adapter_nsrst_assert_width/adapter srst pulse_width/g' $(find tcl/ -type f) Minor indentation issue fixed manually in tcl/board/at91sam9g20-ek.cfg tcl/target/at91sam9260_ext_RAM_ext_flash.cfg Change-Id: I425fd56c0c88cd6b06124621306eeb89166dfe71 Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com> Reviewed-on: http://openocd.zylin.com/5284 Tested-by: jenkins Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
2020-01-29tcl: replace command "interface" with "adapter driver"Antonio Borneo9-9/+9
Avoid annoying "deprecated" messages while running the scripts distributed with OpenOCD code. Change automatically created with command sed -i 's/^interface /adapter driver /' $(find tcl/ -type f) Change-Id: I2291dfb96e164beecbeb3366ce83f9df2ad6c197 Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com> Reviewed-on: http://openocd.zylin.com/5283 Reviewed-by: Marc Schink <dev@zapb.de> Tested-by: jenkins Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
2020-01-27tcl/board: Add config for STM32WB Nucleo boardMarc Schink1-0/+11
Change-Id: Ic29802306c706bcf3e261c60facd01d101c9e1ce Signed-off-by: Marc Schink <dev@zapb.de> Reviewed-on: http://openocd.zylin.com/5358 Tested-by: jenkins Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com> Reviewed-by: Tomas Vanek <vanekt@fbl.cz> Reviewed-by: Ilya Kharin <akscram@gmail.com>
2020-01-02tcl: update scripts after "jtag_reset" got deprecatedAntonio Borneo4-8/+8
Avoid annoying "deprecated" messages in the scripts distributed with OpenOCD code. Change-Id: I82d27cd420db30f0653efbd286a627ef56a8c1fd Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com> Reviewed-on: http://openocd.zylin.com/5287 Tested-by: jenkins Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
2019-12-07target/stm32h7x: add support of dual core variant of STM32H7Tarek BOCHKATI1-0/+16
STM32H7x7 and STM32H7x5 devices contains two cores : CM7 + CM4 The second core creation is only done when * DUAL_CORE variable is set to true * non HLA interface is used A second check for the second core existence is done in cpu1 examine-end Once the second core is detected it gets examined. Furthermore, the script provides a configurable CTI usage in order to halt the cores simultaneously. Tested on Rev X and V devices. PS: the indentation was a mix of spaces and tabs, all changed to tabs. Change-Id: Iad9c30826965ddb9be5dee628bc2e63f953bbcb8 Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com> Reviewed-on: http://openocd.zylin.com/5130 Tested-by: jenkins Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
2019-10-15Update FTDI C232HM cfg, and add two new cfgs from cable modem researchAl Dyrius1-0/+31
Change-Id: Idbeffcd5ff4380b1e7c9fd5ef6ba3ca77cc22d99 Signed-off-by: Al Dyrius <aldyrius42@gmail.com> Reviewed-on: http://openocd.zylin.com/5307 Tested-by: jenkins Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
2019-09-20tcl/board: Add Rigado BMD-300 Evaluation KitMarc Schink1-0/+11
Change-Id: Iba8e12818e2041e51214dab413eb57f0e5bf3f75 Signed-off-by: Marc Schink <openocd-dev@marcschink.de> Reviewed-on: http://openocd.zylin.com/5218 Tested-by: jenkins Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2019-06-19tcl/board: Add SAML11 Xplained Pro Evaluation KitMarc Schink1-0/+10
Change-Id: I118929cdecd9ba1f39d6e2791c114ac7e347b3f5 Signed-off-by: Marc Schink <openocd-dev@marcschink.de> Reviewed-on: http://openocd.zylin.com/5206 Tested-by: jenkins Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
2019-06-19Configs for ARM corelink SSE-200 target and Musca A boardOmair Javaid1-0/+44
This patch adds configuration files for ARM CoreLink SSE-200 SoCs. Also adds configuration file for SSE-200 based Musca A board. Flash programming support for Musca A QSPI flash is still not functional. This configuration will be updated once that support lands into OpenOCD. Please refer to ARM documentation for more information about SSE-200 and Musca A. Change-Id: Id3783c34d6e2609d659ef91c0bf7252c39439874 Signed-off-by: Omair Javaid <omair.javaid@linaro.org> Reviewed-on: http://openocd.zylin.com/5006 Tested-by: jenkins Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
2019-05-20tcl/board: Add Renesas RZ/A1H GR-Peach boardMarek Vasut1-0/+5
Add configuration for the Renesas RZ/A1H GR-Peach board, which is a cheap development kit for the RZ/A1H SoC. Change-Id: I7f5596ae47e6dff8e6d06cffd4dddca20f57d0ca Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Reviewed-on: http://openocd.zylin.com/5142 Tested-by: jenkins Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
2019-04-24tcl/board: Add config for the Amazon Kindle 2 and DXAlexander Kurz1-0/+181
Add a config to access the Amazon Kindle Model No. D00701 and D00801. Both ebook readers are based on a Freescale i.MX31. A JTAG interface is included in a 40 pin FFC connector marked "J9" on both variants. Change-Id: I58bb1ded3d6706bc3798af488ca8bafb7dc45225 Signed-off-by: Alexander Kurz <akurz@blala.de> Reviewed-on: http://openocd.zylin.com/3956 Tested-by: jenkins Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
2019-02-05flash/nor: flash driver and cfg for SAM E54, E53, E51 and D51Tomas Vanek1-0/+13
The new Microchip (former Atmel) series powered by Cortex-M4 looks very similar to older M0+ powered SAM D2x at the first sight. Unfortunately the new series differs a lot in important details. NVMCTRL has different register addresses, moved important bits and even changed binary command set. An universal driver for all SAM D/E would be very complicated. That's why a new driver was derived. Tested on Microchip SAM E54 Xplained Pro kit (board cfg included). Adjusted for the restructured dap support. Checked by valgrind and clang static analyzer. Change-Id: I26c67047a552076f4b207b9b89285a53d69b4ca4 Signed-off-by: Tomas Vanek <vanekt@fbl.cz> Reviewed-on: http://openocd.zylin.com/4272 Tested-by: jenkins Reviewed-by: Andres Vahter <andres.vahter@gmail.com>
2019-01-26tcl: Support for Analog Devices ADSP-SC58x / ADSP-SC584-EZBRDPeter Lawrence1-0/+31
The original script was broken by changes to the Cortex-A code. The recent introduction of the mem_ap target provided a new mechanism to allow the script to be fixed. This also adds an example board script for the ADSP-SC584-EZBRD. Change-Id: I36bc1ac6b6c036539f4175f1e65223ba10a35355 Signed-off-by: Peter Lawrence <majbthrd@gmail.com> Reviewed-on: http://openocd.zylin.com/4855 Tested-by: jenkins Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
2019-01-23Correct ZynqMP configuration to be appropriately namedJonathan McDowell1-2/+2
The xilinx_ultrascale.cfg target is actually the configuration for a ZynqMP, which is a combination of an UltraScale+ FPGA core and a quad core A53. Update the filename/comments to reflect this, and include the tap IDs for all known FPGA cores for this part. Change-Id: I70dfcc99861a482b83b6a795e83021d9cf1fe047 Signed-off-by: Jonathan McDowell <noodles@earth.li> Reviewed-on: http://openocd.zylin.com/4850 Tested-by: jenkins Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
2019-01-02flash: nor: ath79: remove base calculationOleksij Rempel4-4/+4
Currently it is impossible to flash ELF with correct offsets. The reason is a bogus offset calculation extracted from base. Since any other spi drivers do not care about base, do the same for ath79 as well. Change-Id: I9e46e01c9e7a709c2d07da9203c634f302603afd Signed-off-by: Oleksij Rempel <linux@rempel-privat.de> Reviewed-on: http://openocd.zylin.com/4821 Tested-by: jenkins Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
2018-12-12fix cc32xx related changesJiri Kastner1-1/+3
original CC3200 launchpad works only with ti-icdi driver which stopped to work after merging to master commit d02de3a8a92091b9761ebaf44dff1a71f5b2edcb Change-Id: I247b5d99831fa744de1fdc5b8a7cffdf49fe953c Signed-off-by: Jiri Kastner <cz172638@gmail.com> Reviewed-on: http://openocd.zylin.com/4792 Tested-by: jenkins Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2018-11-26tcl/target, board: remove useless gdb-attach event definitionsTomas Vanek5-12/+0
Since commit bae76053dc515252dc5c8235b9a848e461080c66 gdb-attach event is defined as halt by default. Remove useless and in case of bcm281xx wrong definitions of the event. Change-Id: I8e69780a93722eb9392673303f54d502e71eceb6 Signed-off-by: Tomas Vanek <vanekt@fbl.cz> Reviewed-on: http://openocd.zylin.com/4763 Tested-by: jenkins Reviewed-by: Steven Stallion <sstallion@gmail.com>
generated by cgit v1.1 at 2024-11-16 18:04:39 +0000