diff options
29 files changed, 140 insertions, 140 deletions
diff --git a/tcl/board/at91cap7a-stk-sdram.cfg b/tcl/board/at91cap7a-stk-sdram.cfg index df91a6b..8395ba3 100644 --- a/tcl/board/at91cap7a-stk-sdram.cfg +++ b/tcl/board/at91cap7a-stk-sdram.cfg @@ -43,13 +43,13 @@ proc wait_state {expression} { return } } - return -code 1 "Timed out" + return -code 1 "Timed out" } # Use a global variable here to be able to tinker interactively with # post reset jtag frequency. global post_reset_khz -# Danger!!!! Even 16MHz kinda works with this target, but +# Danger!!!! Even 16MHz kinda works with this target, but # it needs to be as low as 2000kHz to be stable. set post_reset_khz 2000 @@ -61,25 +61,25 @@ $_TARGETNAME configure -event reset-init { mww 0xfffffd08 0xa5000001 # Enable main oscillator mww 0xFFFFFc20 0x00000f01 - wait_state {expr {([peek32 0xFFFFFC68] & 0x1) == 0}} + wait_state {expr {([peek32 0xFFFFFC68] & 0x1) == 0}} # Set PLLA to 96MHz mww 0xFFFFFc28 0x20072801 - wait_state {expr {([peek32 0xFFFFFC68] & 0x2) == 0}} + wait_state {expr {([peek32 0xFFFFFC68] & 0x2) == 0}} # Select prescaler mww 0xFFFFFC30 0x00000004 - wait_state {expr {([peek32 0xFFFFFC68] & 0x8) == 0}} + wait_state {expr {([peek32 0xFFFFFC68] & 0x8) == 0}} # Select master clock to 48MHz mww 0xFFFFFC30 0x00000006 - wait_state {expr {([peek32 0xFFFFFC68] & 0x8) == 0}} + wait_state {expr {([peek32 0xFFFFFC68] & 0x8) == 0}} echo "Master clock ok." - + # Now that we're up and running, crank up speed! global post_reset_khz ; adapter speed $post_reset_khz - + echo "Configuring the SDRAM controller..." # Configure EBI Chip select for SDRAM @@ -95,7 +95,7 @@ $_TARGETNAME configure -event reset-init { # Configure SDRAMC CR mww 0xFFFFEA08 0xA63392F9 - + # NOP command mww 0xFFFFEA00 0x1 mww 0x20000000 0 @@ -151,7 +151,7 @@ $_TARGETNAME configure -event reset-init { #remap internal memory at address 0x0 mww 0xffffef00 0x3 - + echo "SDRAM configuration ok." } diff --git a/tcl/board/at91sam9g20-ek.cfg b/tcl/board/at91sam9g20-ek.cfg index 9e0413a..03296c5 100644 --- a/tcl/board/at91sam9g20-ek.cfg +++ b/tcl/board/at91sam9g20-ek.cfg @@ -139,13 +139,13 @@ proc at91sam9g20_reset_init { } { # (MT29F2G08AACWP) can be established by setting four registers in order: SMC_SETUP3, # SMC_PULSE3, SMC_CYCLE3, and SMC_MODE3. Computing the exact values of these registers # is a little tedious to do here. If you have questions about how to do this, Atmel has - # a decent application note #6255B that covers this process. + # a decent application note #6255B that covers this process. mww 0xffffec30 0x00020002 ;# SMC_SETUP3 : 2 clock cycle setup for NRD and NWE mww 0xffffec34 0x04040404 ;# SMC_PULSE3 : 4 clock cycle pulse for all signals mww 0xffffec38 0x00070006 ;# SMC_CYCLE3 : 7 clock cycle NRD and 6 NWE cycle - mww 0xffffec3C 0x00020003 ;# SMC_MODE3 : NRD and NWE control, no NWAIT, 8-bit DBW, - + mww 0xffffec3C 0x00020003 ;# SMC_MODE3 : NRD and NWE control, no NWAIT, 8-bit DBW, + mww 0xffffe800 0x00000001 ;# ECC_CR : reset the ECC parity registers mww 0xffffe804 0x00000002 ;# ECC_MR : page size is 2112 words (word is 8 bits) diff --git a/tcl/board/hilscher_nxdb500sys.cfg b/tcl/board/hilscher_nxdb500sys.cfg index d71c445..20fa3ea 100644 --- a/tcl/board/hilscher_nxdb500sys.cfg +++ b/tcl/board/hilscher_nxdb500sys.cfg @@ -17,7 +17,7 @@ $_TARGETNAME configure -event reset-init { arm7_9 dcc_downloads enable sdram_fix - + puts "Configuring SDRAM controller for paired K4S561632C (64MB) " mww 0x00100140 0 mww 0x00100144 0x03C13261 diff --git a/tcl/board/hilscher_nxeb500hmi.cfg b/tcl/board/hilscher_nxeb500hmi.cfg index aa3d587..a51fa03 100644 --- a/tcl/board/hilscher_nxeb500hmi.cfg +++ b/tcl/board/hilscher_nxeb500hmi.cfg @@ -17,7 +17,7 @@ $_TARGETNAME configure -event reset-init { arm7_9 dcc_downloads disable sdram_fix - + puts "Configuring SDRAM controller for MT48LC8M32 (32MB) " mww 0x00100140 0 mww 0x00100144 0x03C23251 diff --git a/tcl/board/hilscher_nxsb100.cfg b/tcl/board/hilscher_nxsb100.cfg index 807e292..c332bee 100644 --- a/tcl/board/hilscher_nxsb100.cfg +++ b/tcl/board/hilscher_nxsb100.cfg @@ -17,7 +17,7 @@ $_TARGETNAME configure -event reset-init { arm7_9 dcc_downloads enable sdram_fix - + puts "Configuring SDRAM controller for MT48LC2M32 (8MB) " mww 0x00100140 0 mww 0x00100144 0x03C23251 diff --git a/tcl/board/imx31pdk.cfg b/tcl/board/imx31pdk.cfg index 502d407..2dce157 100644 --- a/tcl/board/imx31pdk.cfg +++ b/tcl/board/imx31pdk.cfg @@ -28,36 +28,36 @@ proc imx31pdk_init { } { mww 0x53FC0000 0x040 mww 0x53F80000 0x074B0B7D - + # 399MHz - 26MHz input, PD=1,MFI=7, MFN=27, MFD=40 #mww 0x53F80004 0xFF871D50 #mww 0x53F80010 0x00271C1B - + # Start 16 bit NorFlash Initialization on CS0 mww 0xb8002000 0x0000CC03 mww 0xb8002004 0xa0330D01 mww 0xb8002008 0x00220800 - + # Configure CPLD on CS4 mww 0xb8002040 0x0000DCF6 mww 0xb8002044 0x444A4541 mww 0xb8002048 0x44443302 - + # SDCLK mww 0x43FAC26C 0 - + # CAS mww 0x43FAC270 0 - + # RAS mww 0x43FAC274 0 - + # CS2 (CSD0) mww 0x43FAC27C 0x1000 - + # DQM3 mww 0x43FAC284 0 - + # DQM2, DQM1, DQM0, SD31-SD0, A25-A0, MA10 (0x288..0x2DC) mww 0x43FAC288 0 mww 0x43FAC28C 0 @@ -81,7 +81,7 @@ proc imx31pdk_init { } { mww 0x43FAC2D4 0 mww 0x43FAC2D8 0 mww 0x43FAC2DC 0 - + # Initialization script for 32 bit DDR on MX31 ADS mww 0xB8001010 0x00000004 mww 0xB8001004 0x006ac73a diff --git a/tcl/board/imx35pdk.cfg b/tcl/board/imx35pdk.cfg index b81c0b0..2a7efab 100644 --- a/tcl/board/imx35pdk.cfg +++ b/tcl/board/imx35pdk.cfg @@ -8,9 +8,9 @@ $_TARGETNAME configure -event reset-init { imx35pdk_init } jtag_rclk 10 proc imx35pdk_init { } { - + imx3x_reset - + mww 0x43f00040 0x00000000 mww 0x43f00044 0x00000000 mww 0x43f00048 0x00000000 @@ -25,11 +25,11 @@ proc imx35pdk_init { } { mww 0x53f00050 0x00000000 mww 0x53f00000 0x77777777 mww 0x53f00004 0x77777777 - + # clock setup mww 0x53F80004 0x00821000 ;# first need to set IPU_HND_BYP mww 0x53F80004 0x00821000 ;#arm clock is 399Mhz and ahb clock is 133Mhz. - + #================================================= # WEIM config #================================================= @@ -45,14 +45,14 @@ proc imx35pdk_init { } { mww 0xB8002054 0x444a4541 # CS5A mww 0xB8002058 0x44443302 - + # IO SW PAD Control registers - setting of 0x0002 is high drive, mDDR mww 0x43FAC368 0x00000006 mww 0x43FAC36C 0x00000006 mww 0x43FAC370 0x00000006 mww 0x43FAC374 0x00000006 mww 0x43FAC378 0x00000006 - mww 0x43FAC37C 0x00000006 + mww 0x43FAC37C 0x00000006 mww 0x43FAC380 0x00000006 mww 0x43FAC384 0x00000006 mww 0x43FAC388 0x00000006 @@ -76,7 +76,7 @@ proc imx35pdk_init { } { mww 0x43FAC3D0 0x00000006 mww 0x43FAC3D4 0x00000006 mww 0x43FAC3D8 0x00000006 - + # DDR data bus SD 0 through 31 mww 0x43FAC3DC 0x00000082 mww 0x43FAC3E0 0x00000082 @@ -110,13 +110,13 @@ proc imx35pdk_init { } { mww 0x43FAC450 0x00000082 mww 0x43FAC454 0x00000082 mww 0x43FAC458 0x00000082 - + # DQM setup mww 0x43FAC45c 0x00000082 mww 0x43FAC460 0x00000082 mww 0x43FAC464 0x00000082 mww 0x43FAC468 0x00000082 - + mww 0x43FAC46c 0x00000006 mww 0x43FAC470 0x00000006 mww 0x43FAC474 0x00000006 @@ -130,30 +130,30 @@ proc imx35pdk_init { } { mww 0x43FAC494 0x00000006 mww 0x43FAC498 0x00000006 mww 0x43FAC49c 0x00000006 - mww 0x43FAC4A0 0x00000006 + mww 0x43FAC4A0 0x00000006 mww 0x43FAC4A4 0x00000006 ;# RAS mww 0x43FAC4A8 0x00000006 ;# CAS mww 0x43FAC4Ac 0x00000006 ;# SDWE mww 0x43FAC4B0 0x00000006 ;# SDCKE0 mww 0x43FAC4B4 0x00000006 ;# SDCKE1 mww 0x43FAC4B8 0x00000002 ;# SDCLK - + # SDQS0 through SDQS3 mww 0x43FAC4Bc 0x00000082 mww 0x43FAC4C0 0x00000082 mww 0x43FAC4C4 0x00000082 mww 0x43FAC4C8 0x00000082 - - + + # *================================================== # Initialization script for 32 bit DDR2 on RINGO 3DS # *================================================== - + #-------------------------------------------- # Init CCM #-------------------------------------------- mww 0x53F80028 0x7D000028 - + #-------------------------------------------- # Init IOMUX for JTAG #-------------------------------------------- @@ -164,24 +164,24 @@ proc imx35pdk_init { } { mww 0x43FAC5FC 0x000000F3 mww 0x43FAC600 0x000000F3 mww 0x43FAC604 0x000000F3 - - + + # ESD_MISC : enable DDR2 mww 0xB8001010 0x00000304 - + #-------------------------------------------- # Init 32-bit DDR2 memory on CSD0 # COL=10-bit, ROW=13-bit, BA[1:0]=Addr[26:25] #-------------------------------------------- - + # ESD_ESDCFG0 : set timing parameters - mww 0xB8001004 0x007ffC2f - + mww 0xB8001004 0x007ffC2f + # ESD_ESDCTL0 : select Prechare-All mode mww 0xB8001000 0x92220000 # DDR2 : Prechare-All mww 0x80000400 0x12345678 - + # ESD_ESDCTL0 : select Load-Mode-Register mode mww 0xB8001000 0xB2220000 # DDR2 : Load reg EMR2 @@ -192,18 +192,18 @@ proc imx35pdk_init { } { mwb 0x82000400 0xda # DDR2 : Load reg MR -- reset DLL mwb 0x80000333 0xda - + # ESD_ESDCTL0 : select Prechare-All mode mww 0xB8001000 0x92220000 # DDR2 : Prechare-All mwb 0x80000400 0x12345678 - + # ESD_ESDCTL0 : select Manual-Refresh mode mww 0xB8001000 0xA2220000 # DDR2 : Manual-Refresh 2 times mww 0x80000000 0x87654321 mww 0x80000000 0x87654321 - + # ESD_ESDCTL0 : select Load-Mode-Register mode mww 0xB8001000 0xB2220000 # DDR2 : Load reg MR -- CL=3, BL=8, end DLL reset @@ -212,19 +212,19 @@ proc imx35pdk_init { } { mwb 0x82000780 0xda # DDR2 : Load reg EMR1 -- OCD exit mwb 0x82000400 0xda ;# ODT disabled - + # ESD_ESDCTL0 : select normal-operation mode # DSIZ=32-bit, BL=8, COL=10-bit, ROW=13-bit # disable PWT & PRCT # disable Auto-Refresh mww 0xB8001000 0x82220080 - + ## ESD_ESDCTL0 : enable Auto-Refresh mww 0xB8001000 0x82228080 ## ESD_ESDCTL1 : enable Auto-Refresh mww 0xB8001008 0x00002000 - - + + #*********************************************** # Adjust the ESDCDLY5 register #*********************************************** @@ -233,20 +233,20 @@ proc imx35pdk_init { } { mww 0xB8001024 0x00F48000 ;# this is the default value mww 0xB8001028 0x00F48000 ;# this is the default value mww 0xB800102c 0x00F48000 ;# this is the default value - - + + #Then you can make force measure with the dedicated bit (Bit 7 at ESDMISC) mww 0xB8001010 0x00000384 # wait a while sleep 1000 # now clear the force measurement bit mww 0xB8001010 0x00000304 - + # dummy write to DDR memory to set DQS low mww 0x80000000 0x00000000 - + mww 0x30000100 0x0 mww 0x30000104 0x31024 - - + + } diff --git a/tcl/board/mcb1700.cfg b/tcl/board/mcb1700.cfg index 4954dab..01080a0 100644 --- a/tcl/board/mcb1700.cfg +++ b/tcl/board/mcb1700.cfg @@ -1,5 +1,5 @@ # Keil MCB1700 PCB with 1768 -# +# # Reset init script sets it to 100MHz set CCLK 100000 @@ -53,7 +53,7 @@ $_TARGETNAME configure -event reset-init { # Dividing CPU clock by 8 should be pretty conservative # - # + # global MCB1700_CCLK adapter speed [expr $MCB1700_CCLK / 8] diff --git a/tcl/board/olimex_sam9_l9260.cfg b/tcl/board/olimex_sam9_l9260.cfg index ad2f850..72dce87 100644 --- a/tcl/board/olimex_sam9_l9260.cfg +++ b/tcl/board/olimex_sam9_l9260.cfg @@ -23,15 +23,15 @@ $_TARGETNAME configure -event reset-start { # RCLK is not supported. jtag_rclk 5 halt - - # RSTC_MR : enable user reset, reset length is 64 slow clock cycles. MMU may + + # RSTC_MR : enable user reset, reset length is 64 slow clock cycles. MMU may # be enabled... use physical address. mww phys 0xfffffd08 0xa5000501 } $_TARGETNAME configure -event reset-init { mww 0xfffffd44 0x00008000 ;# WDT_MR : disable watchdog - + ## # Clock configuration for 99.328 MHz main clock. ## @@ -45,23 +45,23 @@ $_TARGETNAME configure -event reset-init { mww 0xfffffc30 0x00000101 ;# PMC_MCKR : no scale on proc clock, master is proc / 2 sleep 10 ;# wait 10 ms mww 0xfffffc30 0x00000102 ;# PMC_MCKR : switch to PLLA (99.328 MHz) - + # Increase JTAG speed to 6 MHz if RCLK is not supported. jtag_rclk 6000 - + arm7_9 dcc_downloads enable ;# Enable faster DCC downloads. - + ## # SDRAM configuration for 2 x Samsung K4S561632J-UC75, 4M x 16Bit x 4 Banks. ## echo "Configuring SDRAM" mww 0xfffff870 0xffff0000 ;# PIOC_ASR : select peripheral function for D15..D31 mww 0xfffff804 0xffff0000 ;# PIOC_PDR : disable PIO function for D15..D31 - + mww 0xffffef1c 0x00010002 ;# EBI_CSA : assign EBI CS1 to SDRAM, VDDIOMSEL set for +3V3 memory - + mww 0xffffea08 0x85237259 ;# SDRAMC_CR : configure SDRAM for Samsung chips - + mww 0xffffea00 0x1 ;# SDRAMC_MR : issue NOP command mww 0x20000000 0 mww 0xffffea00 0x2 ;# SDRAMC_MR : issue an 'All Banks Precharge' command @@ -86,7 +86,7 @@ $_TARGETNAME configure -event reset-init { mww 0x20000000 0 mww 0xffffea00 0x0 ;# SDRAMC_MR : normal mode mww 0x20000000 0 - + mww 0xffffea04 0x2b6 ;# SDRAMC_TR : set refresh timer count to 7 us ## @@ -99,37 +99,37 @@ $_TARGETNAME configure -event reset-init { mww 0xfffff814 0x00002000 ;# PIOC_ODR : disable output on 13 mww 0xfffff830 0x00004000 ;# PIOC_SODR : set 14 to disable NAND mww 0xfffff864 0x00002000 ;# PIOC_PUER : enable pull-up on 13 - + mww 0xffffef1c 0x0001000A ;# EBI_CSA : assign EBI CS3 to NAND, same settings as before - + mww 0xffffec30 0x00010001 ;# SMC_SETUP3 : 1 clock cycle setup for NRD and NWE mww 0xffffec34 0x03030303 ;# SMC_PULSE3 : 3 clock cycle pulse for all signals mww 0xffffec38 0x00050005 ;# SMC_CYCLE3 : 5 clock cycle NRD and NWE cycle - mww 0xffffec3C 0x00020003 ;# SMC_MODE3 : NRD and NWE control, no NWAIT, 8-bit DBW, + mww 0xffffec3C 0x00020003 ;# SMC_MODE3 : NRD and NWE control, no NWAIT, 8-bit DBW, # 3 TDF cycles, no optimization - + mww 0xffffe800 0x00000001 ;# ECC_CR : reset the ECC parity registers mww 0xffffe804 0x00000002 ;# ECC_MR : page size is 2112 words (word is 8 bits) - + nand probe at91sam9260.flash - + ## # Dataflash configuration for 1 x Atmel AT45DB161D, 16Mbit ## echo "Setting up dataflash" - mww 0xfffff404 0x00000807 ;# PIOA_PDR : disable PIO function for 0(SPI0_MISO), 1(SPI0_MOSI), + mww 0xfffff404 0x00000807 ;# PIOA_PDR : disable PIO function for 0(SPI0_MISO), 1(SPI0_MOSI), # 2(SPI0_SPCK), and 11(SPI0_NPCS1) mww 0xfffff470 0x00000007 ;# PIOA_ASR : select peripheral A function for 0, 1, and 2 mww 0xfffff474 0x00000800 ;# PIOA_BSR : select peripheral B function for 11 mww 0xfffffc10 0x00001000 ;# PMC_PCER : enable SPI0 clock - + mww 0xfffc8000 0x00000080 ;# SPI0_CR : software reset SPI0 mww 0xfffc8000 0x00000080 ;# SPI0_CR : again to be sure mww 0xfffc8004 0x000F0011 ;# SPI0_MR : master mode with nothing selected - - mww 0xfffc8034 0x011a0302 ;# SPI0_CSR1 : capture on leading edge, 8-bits/tx. 33MHz baud, + + mww 0xfffc8034 0x011a0302 ;# SPI0_CSR1 : capture on leading edge, 8-bits/tx. 33MHz baud, # 250ns delay before SPCK, 250ns b/n tx - + mww 0xfffc8004 0x000D0011 ;# SPI0_MR : same config, select NPCS1 mww 0xfffc8000 0x00000001 ;# SPI0_CR : enable SPI0 } diff --git a/tcl/board/phytec_lpc3250.cfg b/tcl/board/phytec_lpc3250.cfg index 1c48f5d..cee28cd 100644 --- a/tcl/board/phytec_lpc3250.cfg +++ b/tcl/board/phytec_lpc3250.cfg @@ -23,12 +23,12 @@ $_TARGETNAME configure -event reset-init { phytec_lpc3250_init } # Bare-bones initialization of core clocks and SDRAM proc phytec_lpc3250_init { } { - # Set clock dividers + # Set clock dividers # ARMCLK = 266.5 MHz # HCLK = 133.25 MHz # PERIPHCLK = 13.325 MHz mww 0x400040BC 0 - mww 0x40004050 0x140 + mww 0x40004050 0x140 mww 0x40004040 0x4D mww 0x40004058 0x16250 @@ -37,7 +37,7 @@ proc phytec_lpc3250_init { } { sleep 1 busy mww 0x40004044 0x106 sleep 1 busy - mww 0x40004044 0x006 + mww 0x40004044 0x006 sleep 1 busy mww 0x40004048 0x2 @@ -49,7 +49,7 @@ proc phytec_lpc3250_init { } { mww 0x31080008 0 mww 0x40004068 0x1C000 mww 0x31080028 0x11 - + mww 0x31080400 0 mww 0x31080440 0 mww 0x31080460 0 @@ -66,7 +66,7 @@ proc phytec_lpc3250_init { } { mww 0x31080054 1 mww 0x31080058 1 mww 0x3108005C 0 - + mww 0x31080100 0x5680 mww 0x31080104 0x302 diff --git a/tcl/board/rsc-w910.cfg b/tcl/board/rsc-w910.cfg index cb1733b..574de0c 100644 --- a/tcl/board/rsc-w910.cfg +++ b/tcl/board/rsc-w910.cfg @@ -33,7 +33,7 @@ $_TARGETNAME configure -event reset-start {adapter speed 1000} $_TARGETNAME configure -event reset-init { # switch on PLL for 200MHz operation # running from 15MHz input clock - + mww 0xB0000200 0x00000030 ;# CLKEN mww 0xB0000204 0x00000f3c ;# CLKSEL mww 0xB0000208 0x05007000 ;# CLKDIV @@ -41,17 +41,17 @@ $_TARGETNAME configure -event reset-init { mww 0xB0000210 0x00002b63 ;# PLLCON1 mww 0xB000000C 0x08817fa6 ;# MFSEL sleep 10 - + # we are now running @ 200MHz # enable all openocd speed tweaks - + arm7_9 dcc_downloads enable arm7_9 fast_memory_access enable adapter speed 15000 - + # map nor flash to 0x20000000 # map sdram to 0x00000000 - + mww 0xb0001000 0x000530c1 ;# EBICON mww 0xb0001004 0x40030084 ;# ROMCON mww 0xb0001008 0x000010ee ;# SDCONF0 diff --git a/tcl/board/stm3210e_eval.cfg b/tcl/board/stm3210e_eval.cfg index 91807ce..f30253c 100644 --- a/tcl/board/stm3210e_eval.cfg +++ b/tcl/board/stm3210e_eval.cfg @@ -17,11 +17,11 @@ flash bank $_FLASHNAME cfi 0x64000000 0x01000000 2 2 $_TARGETNAME proc stm32_enable_fsmc {} { echo "Enabling FSMC Bank 1 (NOR/PSRAM Bank 2)" - + # enable gpio (defg) clocks for fsmc # RCC_APB2ENR mww 0x40021018 0x000001E0 - + # enable fsmc clock # RCC_AHBENR mww 0x40021014 0x00000114 @@ -31,29 +31,29 @@ proc stm32_enable_fsmc {} { mww 0x40011400 0x44BB44BB # GPIOD_CRH mww 0x40011404 0xBBBBBBBB - + # GPIOE_CRL mww 0x40011800 0xBBBBB444 # GPIOE_CRH mww 0x40011804 0xBBBBBBBB - + # GPIOF_CRL mww 0x40011C00 0x44BBBBBB # GPIOF_CRH mww 0x40011C04 0xBBBB4444 - + # GPIOG_CRL mww 0x40012000 0x44BBBBBB # GPIOG_CRH mww 0x40012004 0x444444B4 - + # setup fsmc timings # FSMC_BCR1 mww 0xA0000008 0x00001058 - + # FSMC_BTR1 mww 0xA000000C 0x10000502 - + # FSMC_BCR1 - enable fsmc mww 0xA0000008 0x00001059 } diff --git a/tcl/board/uptech_2410.cfg b/tcl/board/uptech_2410.cfg index 680cfd7..227cf42 100644 --- a/tcl/board/uptech_2410.cfg +++ b/tcl/board/uptech_2410.cfg @@ -11,28 +11,28 @@ proc init_pll_sdram { } { #echo "---------- Initializing PLL and SDRAM ---------" #watchdog timer disable mww phys 0x53000000 0x00000000 - + #disable all interrupts mww phys 0x4a000008 0xffffffff - + #disable all sub-interrupts mww phys 0x4a00001c 0x000007ff - + #clear all source pending bits mww phys 0x4a000000 0xffffffff - + #clear all sub-source pending bits mww phys 0x4a000018 0x000007ff - + #clear interrupt pending bit mww phys 0x4a000010 0xffffffff - + #PLL locktime counter mww phys 0x4c000000 0x00ffffff - + #Fin=12MHz Fout=202.8MHz #mww phys 0x4c000004 0x000a1031 - + #FCLK:HCLK:PCLK = 1:2:4 mww phys 0x4c000014 0x00000003 diff --git a/tcl/target/dsp56321.cfg b/tcl/target/dsp56321.cfg index 0ac0ce8..78ecb3b 100644 --- a/tcl/target/dsp56321.cfg +++ b/tcl/target/dsp56321.cfg @@ -1,13 +1,13 @@ # Script for freescale DSP56321 # -if { [info exists CHIPNAME] } { +if { [info exists CHIPNAME] } { set _CHIPNAME $CHIPNAME } else { set _CHIPNAME dsp56321 } -if { [info exists ENDIAN] } { +if { [info exists ENDIAN] } { set _ENDIAN $ENDIAN } else { # this defaults to a big endian diff --git a/tcl/target/dsp568013.cfg b/tcl/target/dsp568013.cfg index 40fa3c2..67d4419 100644 --- a/tcl/target/dsp568013.cfg +++ b/tcl/target/dsp568013.cfg @@ -1,12 +1,12 @@ # Script for freescale DSP568013 -if { [info exists CHIPNAME] } { +if { [info exists CHIPNAME] } { set _CHIPNAME $CHIPNAME } else { set _CHIPNAME dsp568013 } -if { [info exists ENDIAN] } { +if { [info exists ENDIAN] } { set _ENDIAN $ENDIAN } else { # this defaults to a big endian diff --git a/tcl/target/fm3.cfg b/tcl/target/fm3.cfg index 376320e..544cff9 100644 --- a/tcl/target/fm3.cfg +++ b/tcl/target/fm3.cfg @@ -36,10 +36,10 @@ dap create $_CHIPNAME.dap -chain-position $_CHIPNAME.cpu set _TARGETNAME $_CHIPNAME.cpu target create $_TARGETNAME cortex_m -endian $_ENDIAN -dap $_CHIPNAME.dap -# MB9BF506 has 64kB of SRAM on its main system bus +# MB9BF506 has 64kB of SRAM on its main system bus $_TARGETNAME configure -work-area-phys 0x1FFF8000 -work-area-size 0x10000 -work-area-backup 0 -# MB9BF506 has 512kB internal FLASH +# MB9BF506 has 512kB internal FLASH set _FLASHNAME $_CHIPNAME.flash flash bank $_FLASHNAME fm3 0 0 0 0 $_TARGETNAME diff --git a/tcl/target/imx.cfg b/tcl/target/imx.cfg index 9eea53e..ccfddb6 100644 --- a/tcl/target/imx.cfg +++ b/tcl/target/imx.cfg @@ -6,7 +6,7 @@ set TARGETNAME $_TARGETNAME # rewrite commands of the form below to arm11 mcr... # Data.Set c15:0x042f %long 0x40000015 proc setc15 {regs value} { - global TARGETNAME + global TARGETNAME echo [format "set p15 0x%04x, 0x%08x" $regs $value] diff --git a/tcl/target/ixp42x.cfg b/tcl/target/ixp42x.cfg index 3f86e35..624fe29 100644 --- a/tcl/target/ixp42x.cfg +++ b/tcl/target/ixp42x.cfg @@ -66,8 +66,8 @@ set IXP42x_SDRAM_256MB_32Mx16_2BANK 0x0015 # helper function to init SDRAM on IXP42x. # SDRAM_CFG: one of IXP42X_SDRAM_xxx -# REFRESH: refresh counter reload value (integer) -# CASLAT: 2 or 3 +# REFRESH: refresh counter reload value (integer) +# CASLAT: 2 or 3 proc ixp42x_init_sdram { SDRAM_CFG REFRESH CASLAT } { switch $CASLAT { diff --git a/tcl/target/lpc2103.cfg b/tcl/target/lpc2103.cfg index f55777f..131b9ef 100644 --- a/tcl/target/lpc2103.cfg +++ b/tcl/target/lpc2103.cfg @@ -15,7 +15,7 @@ proc setup_lpc2103 {core_freq_khz adapter_freq_khz} { proc init_targets {} { # default to core clocked with 12MHz crystal echo "Warning - assuming default core clock 12MHz! Flashing may fail if actual core clock is different." - + # setup_lpc2103 <core_freq_khz> <adapter_freq_khz> setup_lpc2103 12000 1500 } diff --git a/tcl/target/lpc2124.cfg b/tcl/target/lpc2124.cfg index 0251738..ddbde22 100644 --- a/tcl/target/lpc2124.cfg +++ b/tcl/target/lpc2124.cfg @@ -15,7 +15,7 @@ proc setup_lpc2124 {core_freq_khz adapter_freq_khz} { proc init_targets {} { # default to core clocked with 12MHz crystal echo "Warning - assuming default core clock 12MHz! Flashing may fail if actual core clock is different." - + # setup_lpc2124 <core_freq_khz> <adapter_freq_khz> setup_lpc2124 12000 1500 } diff --git a/tcl/target/lpc2129.cfg b/tcl/target/lpc2129.cfg index 2c33cde..a1c3fe7 100644 --- a/tcl/target/lpc2129.cfg +++ b/tcl/target/lpc2129.cfg @@ -15,7 +15,7 @@ proc setup_lpc2129 {core_freq_khz adapter_freq_khz} { proc init_targets {} { # default to core clocked with 12MHz crystal echo "Warning - assuming default core clock 12MHz! Flashing may fail if actual core clock is different." - + # setup_lpc2129 <core_freq_khz> <adapter_freq_khz> setup_lpc2129 12000 1500 } diff --git a/tcl/target/lpc2148.cfg b/tcl/target/lpc2148.cfg index f3a2011..503a682 100644 --- a/tcl/target/lpc2148.cfg +++ b/tcl/target/lpc2148.cfg @@ -15,7 +15,7 @@ proc setup_lpc2148 {core_freq_khz adapter_freq_khz} { proc init_targets {} { # default to core clocked with 12MHz crystal echo "Warning - assuming default core clock 12MHz! Flashing may fail if actual core clock is different." - + # setup_lpc2148 <core_freq_khz> <adapter_freq_khz> setup_lpc2148 12000 1500 } diff --git a/tcl/target/lpc2294.cfg b/tcl/target/lpc2294.cfg index 83d595d..1320cda 100644 --- a/tcl/target/lpc2294.cfg +++ b/tcl/target/lpc2294.cfg @@ -9,7 +9,7 @@ source [find target/lpc2xxx.cfg] proc setup_lpc2294 {core_freq_khz adapter_freq_khz} { # 256kB flash and 16kB SRAM # setup_lpc2xxx <chip_name> <cputapid> <flash_size> <flash_variant> <workarea_size> <core_freq_khz> <adapter_freq_khz> - + # !! TAPID unknown !! setup_lpc2xxx lpc2294 0xffffffff 0x40000 lpc2000_v1 0x4000 $core_freq_khz $adapter_freq_khz } @@ -17,7 +17,7 @@ proc setup_lpc2294 {core_freq_khz adapter_freq_khz} { proc init_targets {} { # default to core clocked with 12MHz crystal echo "Warning - assuming default core clock 12MHz! Flashing may fail if actual core clock is different." - + # setup_lpc2294 <core_freq_khz> <adapter_freq_khz> setup_lpc2294 12000 1500 } diff --git a/tcl/target/lpc2378.cfg b/tcl/target/lpc2378.cfg index 0b66b82..235456a 100644 --- a/tcl/target/lpc2378.cfg +++ b/tcl/target/lpc2378.cfg @@ -15,7 +15,7 @@ proc setup_lpc2378 {core_freq_khz adapter_freq_khz} { proc init_targets {} { # default to core clocked with 4MHz internal oscillator echo "Warning - assuming default core clock 4MHz! Flashing may fail if actual core clock is different." - + # setup_lpc2378 <core_freq_khz> <adapter_freq_khz> setup_lpc2378 4000 500 } diff --git a/tcl/target/lpc2460.cfg b/tcl/target/lpc2460.cfg index 69fdc4a..c229f6d 100644 --- a/tcl/target/lpc2460.cfg +++ b/tcl/target/lpc2460.cfg @@ -15,7 +15,7 @@ proc setup_lpc2460 {core_freq_khz adapter_freq_khz} { proc init_targets {} { # default to core clocked with 4MHz internal oscillator echo "Warning - assuming default core clock 4MHz! Flashing may fail if actual core clock is different." - + # setup_lpc2460 <core_freq_khz> <adapter_freq_khz> setup_lpc2460 4000 500 } diff --git a/tcl/target/lpc2478.cfg b/tcl/target/lpc2478.cfg index 48e5bdf..36b5c46 100644 --- a/tcl/target/lpc2478.cfg +++ b/tcl/target/lpc2478.cfg @@ -15,7 +15,7 @@ proc setup_lpc2478 {core_freq_khz adapter_freq_khz} { proc init_targets {} { # default to core clocked with 4MHz internal oscillator echo "Warning - assuming default core clock 4MHz! Flashing may fail if actual core clock is different." - + # setup_lpc2478 <core_freq_khz> <adapter_freq_khz> setup_lpc2478 4000 500 } diff --git a/tcl/target/lpc2xxx.cfg b/tcl/target/lpc2xxx.cfg index 4c3394c..f947c1b 100644 --- a/tcl/target/lpc2xxx.cfg +++ b/tcl/target/lpc2xxx.cfg @@ -40,5 +40,5 @@ proc setup_lpc2xxx {chip_name cputapids flash_size flash_variant workarea_size c proc init_targets {} { # FIX!!! read out CPUTAPID here and choose right setup. In addition to the # CPUTAPID some querying of the target would be required. - return -error "This is a generic LPC2xxx configuration file, use a specific target file." + return -error "This is a generic LPC2xxx configuration file, use a specific target file." } diff --git a/tcl/target/lpc3131.cfg b/tcl/target/lpc3131.cfg index d6f2cdb..89bbf02 100644 --- a/tcl/target/lpc3131.cfg +++ b/tcl/target/lpc3131.cfg @@ -56,7 +56,7 @@ adapter srst delay 1000 jtag_ntrst_delay 0 set _TARGETNAME $_CHIPNAME.cpu -target create $_TARGETNAME arm926ejs -endian $_ENDIAN -chain-position $_TARGETNAME +target create $_TARGETNAME arm926ejs -endian $_ENDIAN -chain-position $_TARGETNAME $_TARGETNAME invoke-event halted diff --git a/tcl/target/u8500.cfg b/tcl/target/u8500.cfg index baef9c8..36e0db7 100644 --- a/tcl/target/u8500.cfg +++ b/tcl/target/u8500.cfg @@ -1,6 +1,6 @@ # Copyright (C) ST-Ericsson SA 2011 # Author : michel.jaouen@stericsson.com -# U8500 target +# U8500 target proc mmu_off {} { set cp [arm mrc 15 0 1 0 0] @@ -31,7 +31,7 @@ proc ocd_gdb_restart {target_id} { proc smp_reg {} { global _TARGETNAME_1 global _TARGETNAME_2 - targets $_TARGETNAME_1 + targets $_TARGETNAME_1 echo "$_TARGETNAME_1" set pc1 [reg pc] set stck1 [reg sp_svc] @@ -68,7 +68,7 @@ proc pwrsts { } { 8 { echo "A9 100% DVFS" } - c { + c { echo "A9 50% DVFS" } } @@ -144,7 +144,7 @@ tcl_port 5555 telnet_port 4444 gdb_port 3333 -if { [info exists CHIPNAME] } { +if { [info exists CHIPNAME] } { global _CHIPNAME set _CHIPNAME $CHIPNAME } else { @@ -194,12 +194,12 @@ set _TARGETNAME_1 $TARGETNAME_1 if { [info exists DAP_DBG1] } { set _DAP_DBG1 $DAP_DBG1 } else { - set _DAP_DBG1 0x801A8000 + set _DAP_DBG1 0x801A8000 } if { [info exists DAP_DBG2] } { set _DAP_DBG2 $DAP_DBG2 } else { - set _DAP_DBG2 0x801AA000 + set _DAP_DBG2 0x801AA000 } dap create $_CHIPNAME.dap -chain-position $_CHIPNAME.cpu @@ -226,7 +226,7 @@ global _SMP set _SMP $SMP } global SMP -if { $_SMP == 1} { +if { $_SMP == 1} { target smp $_CHIPNAME.cpu2 $_CHIPNAME.cpu1 } @@ -264,7 +264,7 @@ proc att { } { } else { echo "target secured" } - + } @@ -310,10 +310,10 @@ if {![info exists MAXSPEED]} { global _MAXSPEED set _MAXSPEED 15000 } else { -global _MAXSPEED +global _MAXSPEED set _MAXSPEED $MAXSPEED } -global _MAXSPEED +global _MAXSPEED adapter speed $_MAXSPEED |