diff options
| author | Uwe Hermann <uwe@hermann-uwe.de> | 2012-04-11 00:02:51 +0200 |
|---|---|---|
| committer | Spencer Oliver <spen@spen-soft.co.uk> | 2012-04-13 08:57:29 +0000 |
| commit | b6068f5a48f26db419217ac6b407a2746759e62a (patch) | |
| tree | 5146c6f975bcc69f6b5724274e07bf2623fc978c /tcl | |
| parent | 3c270bb0a98c7b59f3d19203273752a38dd65b65 (diff) | |
| download | riscv-openocd-b6068f5a48f26db419217ac6b407a2746759e62a.zip riscv-openocd-b6068f5a48f26db419217ac6b407a2746759e62a.tar.gz riscv-openocd-b6068f5a48f26db419217ac6b407a2746759e62a.tar.bz2 | |
Glyn Tonga2: Faster JTAG speed after CPU/RAM init.
Change-Id: Ib08dae0035355138c468483a7ee2d73aadedf430
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Reviewed-on: http://openocd.zylin.com/564
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Diffstat (limited to 'tcl')
| -rw-r--r-- | tcl/board/glyn_tonga2.cfg | 34 |
1 files changed, 32 insertions, 2 deletions
diff --git a/tcl/board/glyn_tonga2.cfg b/tcl/board/glyn_tonga2.cfg index 783ef9f..17ed3cf 100644 --- a/tcl/board/glyn_tonga2.cfg +++ b/tcl/board/glyn_tonga2.cfg @@ -16,10 +16,38 @@ source [find target/tmpa900.cfg] # Target configuration # ######################## -$_TARGETNAME configure -event reset-init { tonga2_init } +# Initial JTAG speed should not exceed 1/6 of the initial CPU clock +# frequency (24MHz). Be conservative and use 1/8 of the frequency. +# (24MHz / 8 = 3MHz) +adapter_khz 3000 -proc tonga2_init { } { +$_TARGETNAME configure -event reset-start { + # Upon reset, set the JTAG frequency to 3MHz again, see above. + echo "Setting JTAG speed to 3MHz until clocks are initialized." + adapter_khz 3000 + + # Halt the CPU. + halt + + # Disable faster memory access for now. + arm7_9 fast_memory_access disable +} + +$_TARGETNAME configure -event reset-init { + # Setup clocks, and initialize SRAM and DDR SDRAM. + tonga2_init + # At this point the CPU is running at 192MHz, increase JTAG speed. + # Tests showed that 15MHz works OK, higher speeds can cause problems, + # though. Not sure if this is a CPU issue or JTAG adapter issue. + echo "Increasing JTAG speed to 15MHz." + adapter_khz 15000 + + # Enable faster memory access. + arm7_9 fast_memory_access enable +} + +proc tonga2_init { } { ###################### # PLL initialization # ###################### @@ -160,6 +188,8 @@ proc tonga2_init { } { # smc_direct_cmd_5 (SMC Direct Command register): # cmd_type = UpdateRegs, chip_select = CS1 mww 0xf4311010 0x00c00000 + + echo "Clocks, SRAM, and DDR SDRAM are now initialized." } ####################### |