1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
361
362
363
364
365
366
367
368
369
370
371
372
373
374
375
376
377
378
379
380
381
382
383
384
385
386
387
388
389
390
391
392
393
394
395
396
397
398
399
400
401
402
403
404
405
406
407
408
409
410
411
412
413
414
415
416
417
418
419
420
421
422
423
424
425
426
427
428
429
430
431
432
433
434
435
436
437
438
439
440
441
442
443
444
445
446
447
448
449
450
451
452
453
454
455
456
457
458
459
460
461
462
463
464
465
466
467
468
469
470
471
472
473
474
475
476
477
478
479
480
481
482
483
484
485
486
487
488
489
490
491
492
493
494
495
496
497
498
499
500
501
502
503
504
505
506
507
508
509
510
511
512
513
514
515
516
517
518
519
520
521
522
523
524
525
526
527
528
529
530
531
532
533
534
535
536
537
538
539
540
541
542
543
544
545
546
547
548
549
550
551
552
553
554
555
556
557
558
559
560
561
562
563
564
565
566
567
568
569
570
571
572
573
574
575
576
577
578
579
580
581
582
583
584
585
586
587
588
589
590
591
592
593
594
595
596
597
598
599
600
601
602
603
604
605
606
607
608
609
610
611
612
613
614
615
616
617
618
619
620
621
622
623
624
625
626
627
628
629
630
631
632
633
634
635
636
637
638
639
640
641
642
643
644
645
646
647
648
649
650
651
652
653
654
655
656
657
658
659
660
661
662
663
664
665
666
667
668
669
670
671
672
673
674
675
676
677
678
679
680
681
682
683
684
685
686
687
688
689
690
691
692
693
694
695
696
697
698
699
700
701
702
703
704
705
706
707
708
709
710
711
712
713
714
715
716
717
718
719
720
721
722
723
724
725
726
727
728
729
730
731
732
733
734
735
736
737
738
739
740
741
742
743
744
745
746
747
748
749
750
751
752
753
754
755
756
757
758
759
760
761
762
763
764
765
766
767
768
769
770
771
772
773
774
775
776
777
778
779
780
781
782
783
784
785
786
787
788
789
790
791
792
793
794
795
796
797
798
799
800
801
802
803
804
805
806
807
808
809
810
811
812
813
814
815
816
817
818
819
820
821
822
823
824
825
826
827
828
829
830
831
832
833
834
835
836
837
838
839
840
841
842
843
844
845
846
847
848
849
850
851
852
853
854
855
856
857
858
859
860
861
862
863
864
865
866
867
868
869
870
871
872
873
874
875
876
877
878
879
880
881
882
883
884
885
886
887
888
889
890
891
892
893
894
895
896
897
898
899
900
901
902
903
904
905
906
907
908
909
910
911
912
913
914
915
916
917
918
919
920
921
922
923
924
925
926
927
928
929
930
931
932
933
934
935
936
937
938
939
940
941
942
943
944
945
946
947
948
949
950
951
952
953
954
955
956
957
958
959
960
961
962
963
964
965
966
967
968
969
970
971
972
973
974
975
976
977
978
979
980
981
982
983
984
985
986
987
988
989
990
991
992
993
994
995
996
997
998
999
1000
1001
1002
1003
1004
1005
1006
1007
1008
1009
1010
1011
1012
1013
1014
1015
1016
1017
1018
1019
1020
1021
1022
1023
1024
1025
1026
1027
1028
1029
1030
1031
1032
1033
1034
1035
1036
1037
1038
1039
1040
1041
1042
1043
1044
1045
1046
1047
1048
1049
1050
1051
1052
1053
1054
1055
1056
1057
1058
1059
1060
1061
1062
1063
1064
1065
1066
1067
1068
1069
1070
1071
1072
1073
1074
1075
1076
1077
1078
1079
1080
1081
1082
1083
1084
1085
1086
1087
1088
1089
1090
1091
1092
1093
1094
1095
1096
1097
1098
1099
1100
1101
1102
1103
1104
1105
1106
1107
1108
1109
1110
1111
1112
1113
1114
1115
1116
1117
1118
1119
1120
1121
1122
1123
1124
1125
1126
1127
1128
1129
1130
1131
1132
1133
1134
1135
1136
1137
1138
1139
1140
1141
1142
1143
1144
1145
1146
1147
1148
1149
1150
1151
1152
1153
1154
1155
1156
1157
1158
1159
1160
1161
1162
1163
1164
1165
1166
1167
1168
1169
1170
1171
1172
1173
1174
1175
1176
1177
1178
1179
1180
1181
1182
1183
1184
1185
1186
1187
1188
1189
1190
1191
1192
1193
1194
1195
1196
1197
1198
1199
1200
1201
1202
1203
1204
1205
1206
1207
1208
1209
1210
1211
1212
1213
1214
1215
1216
1217
1218
1219
1220
1221
1222
1223
1224
1225
1226
1227
1228
1229
1230
1231
1232
1233
1234
1235
1236
1237
1238
1239
1240
1241
1242
1243
1244
1245
1246
1247
1248
1249
1250
1251
1252
1253
1254
1255
1256
1257
1258
1259
1260
1261
1262
1263
1264
1265
1266
1267
1268
1269
1270
1271
1272
1273
1274
1275
1276
1277
1278
1279
1280
1281
1282
1283
1284
1285
1286
1287
1288
1289
1290
1291
1292
1293
1294
1295
1296
1297
1298
1299
1300
1301
1302
1303
1304
1305
1306
1307
1308
1309
1310
1311
1312
1313
1314
1315
1316
1317
1318
1319
1320
1321
1322
1323
1324
1325
1326
1327
1328
1329
1330
1331
1332
1333
1334
1335
1336
1337
1338
1339
1340
1341
1342
1343
1344
1345
1346
1347
1348
1349
1350
1351
1352
1353
1354
1355
1356
1357
1358
1359
1360
1361
1362
1363
1364
1365
1366
1367
1368
1369
1370
1371
1372
1373
1374
1375
1376
1377
1378
1379
1380
1381
1382
1383
1384
1385
1386
1387
1388
1389
1390
1391
1392
1393
1394
1395
1396
1397
1398
1399
1400
1401
1402
1403
1404
1405
1406
1407
1408
1409
1410
1411
1412
1413
1414
1415
1416
1417
1418
1419
1420
1421
1422
1423
1424
1425
1426
1427
1428
1429
1430
1431
1432
1433
1434
1435
1436
1437
1438
1439
1440
1441
1442
1443
1444
1445
1446
1447
1448
1449
1450
1451
1452
1453
1454
1455
1456
1457
1458
1459
1460
1461
1462
1463
1464
1465
1466
1467
1468
1469
1470
1471
1472
1473
1474
1475
1476
1477
1478
1479
1480
1481
1482
1483
1484
1485
1486
1487
1488
1489
1490
1491
1492
1493
1494
1495
1496
1497
1498
1499
1500
1501
1502
1503
1504
1505
1506
1507
1508
1509
1510
1511
1512
1513
1514
1515
1516
1517
1518
1519
1520
1521
1522
1523
1524
1525
1526
1527
1528
1529
1530
1531
1532
1533
1534
1535
1536
1537
1538
1539
1540
1541
1542
1543
1544
1545
1546
1547
1548
1549
1550
1551
1552
1553
1554
1555
1556
1557
1558
1559
1560
1561
1562
1563
1564
1565
1566
1567
1568
1569
1570
1571
1572
1573
1574
1575
1576
1577
1578
1579
1580
1581
1582
1583
1584
1585
1586
1587
1588
1589
1590
1591
1592
1593
1594
1595
1596
1597
1598
1599
1600
1601
1602
1603
1604
1605
1606
1607
1608
1609
1610
1611
1612
1613
1614
1615
1616
1617
1618
1619
1620
1621
1622
1623
1624
1625
1626
1627
1628
1629
1630
1631
1632
1633
1634
1635
1636
1637
1638
1639
1640
1641
1642
1643
1644
1645
1646
1647
1648
1649
1650
1651
1652
1653
1654
1655
1656
1657
1658
1659
1660
1661
1662
1663
1664
1665
1666
1667
1668
1669
1670
1671
1672
1673
1674
1675
1676
1677
1678
1679
1680
1681
1682
1683
1684
1685
1686
1687
1688
1689
1690
1691
1692
1693
1694
1695
1696
1697
1698
1699
1700
1701
1702
1703
1704
1705
1706
1707
1708
1709
1710
1711
1712
1713
1714
1715
|
\chapter{Supervisor-Level ISA, Version 1.12}
\label{supervisor}
This chapter describes the RISC-V supervisor-level architecture, which
contains a common core that is used with various supervisor-level
address translation and protection schemes.
\begin{commentary}
Supervisor mode is deliberately restricted in terms of interactions
with underlying physical hardware, such as physical memory and device
interrupts, to support clean virtualization.
In this spirit, certain supervisor-level facilities, including requests for
timer and interprocessor interrupts, are provided by implementation-specific
mechanisms. In some systems, a supervisor execution environment (SEE)
provides these facilities in a manner specified by a supervisor binary
interface (SBI). Other systems supply these facilities directly, through some
other implementation-defined mechanism.
\end{commentary}
\section{Supervisor CSRs}
A number of CSRs are provided for the supervisor.
\begin{commentary}
The supervisor should only view CSR state that should be visible to a
supervisor-level operating system. In particular, there is no
information about the existence (or non-existence) of higher privilege
levels (machine level or other) visible in the CSRs accessible by the
supervisor.
Many supervisor CSRs are a subset of the equivalent machine-mode CSR,
and the machine-mode chapter should be read first to help understand
the supervisor-level CSR descriptions.
\end{commentary}
\subsection{Supervisor Status Register (\tt sstatus)}
\label{sstatus}
The {\tt sstatus} register is an SXLEN-bit read/write register
formatted as shown in Figure~\ref{sstatusreg-rv32} for RV32 and
Figure~\ref{sstatusreg} for RV64. The {\tt sstatus}
register keeps track of the processor's current operating state.
\begin{figure*}[h!]
{\footnotesize
\begin{center}
\setlength{\tabcolsep}{4pt}
\scalebox{0.95}{
\begin{tabular}{cWcccccWccccWcc}
\\
\instbit{31} &
\instbitrange{30}{20} &
\instbit{19} &
\instbit{18} &
\instbit{17} &
\instbitrange{16}{15} &
\instbitrange{14}{13} &
\instbitrange{12}{9} &
\instbit{8} &
\instbit{7} &
\instbit{6} &
\instbit{5} &
\instbitrange{4}{2} &
\instbit{1} &
\instbit{0} \\
\hline
\multicolumn{1}{|c|}{SD} &
\multicolumn{1}{c|}{\wpri} &
\multicolumn{1}{c|}{MXR} &
\multicolumn{1}{c|}{SUM} &
\multicolumn{1}{c|}{\wpri} &
\multicolumn{1}{c|}{XS[1:0]} &
\multicolumn{1}{c|}{FS[1:0]} &
\multicolumn{1}{c|}{\wpri} &
\multicolumn{1}{c|}{SPP} &
\multicolumn{1}{c|}{\wpri} &
\multicolumn{1}{c|}{UBE} &
\multicolumn{1}{c|}{SPIE} &
\multicolumn{1}{c|}{\wpri} &
\multicolumn{1}{c|}{SIE} &
\multicolumn{1}{c|}{\wpri}
\\
\hline
1 & 11 & 1 & 1 & 1 & 2 & 2 & 4 & 1 & 1 & 1 & 1 & 3 & 1 & 1 \\
\end{tabular}}
\end{center}
}
\vspace{-0.1in}
\caption{Supervisor-mode status register ({\tt sstatus}) for RV32.}
\label{sstatusreg-rv32}
\end{figure*}
\begin{figure*}[h!]
{\footnotesize
\begin{center}
\setlength{\tabcolsep}{4pt}
\begin{tabular}{cMFScccc}
\\
\instbit{SXLEN-1} &
\instbitrange{SXLEN-2}{34} &
\instbitrange{33}{32} &
\instbitrange{31}{20} &
\instbit{19} &
\instbit{18} &
\instbit{17} &
\\
\hline
\multicolumn{1}{|c|}{SD} &
\multicolumn{1}{c|}{\wpri} &
\multicolumn{1}{c|}{UXL[1:0]} &
\multicolumn{1}{c|}{\wpri} &
\multicolumn{1}{c|}{MXR} &
\multicolumn{1}{c|}{SUM} &
\multicolumn{1}{c|}{\wpri} &
\\
\hline
1 & SXLEN-35 & 2 & 12 & 1 & 1 & 1 & \\
\end{tabular}
\begin{tabular}{cWWFccccWcc}
\\
&
\instbitrange{16}{15} &
\instbitrange{14}{13} &
\instbitrange{12}{9} &
\instbit{8} &
\instbit{7} &
\instbit{6} &
\instbit{5} &
\instbitrange{4}{2} &
\instbit{1} &
\instbit{0} \\
\hline
&
\multicolumn{1}{|c|}{XS[1:0]} &
\multicolumn{1}{c|}{FS[1:0]} &
\multicolumn{1}{c|}{\wpri} &
\multicolumn{1}{c|}{SPP} &
\multicolumn{1}{c|}{\wpri} &
\multicolumn{1}{c|}{UBE} &
\multicolumn{1}{c|}{SPIE} &
\multicolumn{1}{c|}{\wpri} &
\multicolumn{1}{c|}{SIE} &
\multicolumn{1}{c|}{\wpri} \\
\hline
& 2 & 2 & 4 & 1 & 1 & 1 & 1 & 3 & 1 & 1 \\
\end{tabular}
\end{center}
}
\vspace{-0.1in}
\caption{Supervisor-mode status register ({\tt sstatus}) for RV64.}
\label{sstatusreg}
\end{figure*}
The SPP bit indicates the privilege level at which a hart was executing before
entering supervisor mode. When a trap is taken, SPP is set to 0 if the trap
originated from user mode, or 1 otherwise. When an SRET instruction
(see Section~\ref{otherpriv}) is executed to return from the trap handler, the
privilege level is set to user mode if the SPP bit is 0, or supervisor mode if
the SPP bit is 1; SPP is then set to 0.
The SIE bit enables or disables all interrupts in supervisor mode.
When SIE is clear, interrupts are not taken while in supervisor mode.
When the hart is running in user-mode, the value in SIE is ignored, and
supervisor-level interrupts are enabled. The supervisor can disable
individual interrupt sources using the {\tt sie} CSR.
The SPIE bit indicates whether supervisor interrupts were enabled prior to
trapping into supervisor mode. When a trap is taken into supervisor
mode, SPIE is set to SIE, and SIE is set to 0. When an SRET instruction is
executed, SIE is set to SPIE, then SPIE is set to 1.
\begin{commentary}
The {\tt sstatus} register is a subset of the {\tt mstatus} register. In
a straightforward implementation, reading or writing any field in {\tt
sstatus} is equivalent to reading or writing the homonymous field in
{\tt mstatus}.
\end{commentary}
\subsubsection{Base ISA Control in {\tt sstatus} Register}
The UXL field controls the value of XLEN for U-mode, termed {\em UXLEN},
which may differ from the value of XLEN for S-mode, termed {\em SXLEN}. The
encoding of UXL is the same as that of the MXL field of {\tt misa}, shown in
Table~\ref{misabase}.
For RV32 systems, the UXL field does not exist, and UXLEN=32. For RV64
systems, it is a \warl\ field that encodes the current value of UXLEN.
In particular, the implementation may hardwire UXL so that UXLEN=SXLEN.
If UXLEN~$\ne$~SXLEN, instructions executed in the narrower mode must ignore
source register operand bits above the configured XLEN, and must sign-extend
results to fill the widest supported XLEN in the destination register.
If UXLEN~$<$~SXLEN, user-mode instruction-fetch addresses and load and store
effective addresses are taken modulo $2^{UXLEN}$. For example, when UXLEN=32
and SXLEN=64, user-mode memory accesses reference the lowest \wunits{4}{GiB}
of the address space.
\subsubsection{Memory Privilege in {\tt sstatus} Register}
\label{sec:sum}
The MXR (Make eXecutable Readable) bit modifies the privilege with which loads
access virtual memory. When MXR=0, only loads from pages marked readable (R=1
in Figure~\ref{sv32pte}) will succeed. When MXR=1, loads from pages marked
either readable or executable (R=1 or X=1) will succeed. MXR has no effect
when page-based virtual memory is not in effect.
The SUM (permit Supervisor User Memory access) bit modifies the privilege with
which S-mode loads and stores access virtual memory.
When SUM=0, S-mode memory accesses to pages that are accessible by U-mode (U=1
in Figure~\ref{sv32pte}) will fault. When SUM=1, these accesses are permitted.
SUM has no effect when page-based virtual memory is not in effect, nor when
executing in U-mode. Note that S-mode can never execute instructions from user
pages, regardless of the state of SUM.
\begin{commentary}
The SUM mechanism prevents supervisor software from inadvertently accessing
user memory. Operating systems can execute the majority of code with SUM clear;
the few code segments that should access user memory can temporarily set
SUM.
The SUM mechanism does not avail S-mode software of permission to execute
instructions in user code pages. Legitimate uses cases for execution from
user memory in supervisor context are rare in general and nonexistent in POSIX
environments. However, bugs in supervisors that lead to arbitrary code
execution are much easier to exploit if the supervisor exploit code can be
stored in a user buffer at a virtual address chosen by an attacker.
Some non-POSIX single address space operating systems do allow certain
privileged software to partially execute in supervisor mode, while most
programs run in user mode, all in a shared address space. This use case can
be realized by mapping the physical code pages at multiple virtual addresses
with different permissions, possibly with the assistance of the
instruction page-fault handler to direct supervisor software to use the
alternate mapping.
\end{commentary}
\subsubsection{Endianness Control in {\tt sstatus} Register}
The UBE bit is a \warl\ field that controls the endianness of explicit
memory accesses made from U-mode, which may differ from the endianness of
memory accesses in S-mode.
An implementation may hardwire UBE to specify always the same endianness
as for S-mode.
UBE controls whether explicit
load and store memory accesses made from U-mode are little-endian (UBE=0)
or big-endian (UBE=1).
UBE has no effect on instruction fetches, which are {\em implicit} memory
accesses that are always little-endian.
For {\em implicit} accesses to supervisor-level memory management data
structures, such as page tables, S-mode endianness always applies and UBE
is ignored.
\begin{commentary}
Standard RISC-V ABIs are expected to be purely little-endian-only or
big-endian-only, with no accommodation for mixing endianness.
Nevertheless, endianness control has been defined so as to permit an
OS of one endianness to execute user-mode programs of the opposite
endianness.
\end{commentary}
\subsection{Supervisor Trap Vector Base Address Register ({\tt stvec})}
The {\tt stvec} register is an SXLEN-bit read/write register that holds
trap vector configuration, consisting of a vector base address (BASE) and a
vector mode (MODE).
\begin{figure*}[h!]
{\footnotesize
\begin{center}
\begin{tabular}{J@{}R}
\instbitrange{SXLEN-1}{2} &
\instbitrange{1}{0} \\
\hline
\multicolumn{1}{|c|}{BASE[SXLEN-1:2] (\warl)} &
\multicolumn{1}{c|}{MODE (\warl)} \\
\hline
SXLEN-2 & 2 \\
\end{tabular}
\end{center}
}
\vspace{-0.1in}
\caption{Supervisor trap vector base address register ({\tt stvec}).}
\label{stvecreg}
\end{figure*}
The BASE field in {\tt stvec} is a \warl\ field that can hold any valid
virtual or physical address, subject to the following alignment constraints:
the address must be 4-byte aligned, and MODE settings other than Direct might
impose additional alignment constraints on the value in the BASE field.
\begin{table*}[h!]
\begin{center}
\begin{tabular}{|r|c|l|}
\hline
Value & Name & Description \\
\hline
0 & Direct & All exceptions set {\tt pc} to BASE. \\
1 & Vectored & Asynchronous interrupts set {\tt pc} to BASE+4$\times$cause. \\
$\ge$2 & --- & {\em Reserved} \\
\hline
\end{tabular}
\end{center}
\caption{Encoding of {\tt stvec} MODE field.}
\label{stvec-mode}
\end{table*}
The encoding of the MODE field is shown in Table~\ref{stvec-mode}. When
MODE=Direct, all traps into supervisor mode cause the {\tt pc} to be set to the
address in the BASE field. When MODE=Vectored, all synchronous exceptions
into supervisor mode cause the {\tt pc} to be set to the address in the BASE
field, whereas interrupts cause the {\tt pc} to be set to the address in
the BASE field plus four times the interrupt cause number. For example,
a supervisor-mode timer interrupt (see Table~\ref{scauses}) causes the {\tt pc}
to be set to BASE+{\tt 0x14}.
Setting MODE=Vectored may impose a stricter alignment constraint on BASE.
\subsection{Supervisor Interrupt Registers ({\tt sip} and {\tt sie})}
The {\tt sip} register is an SXLEN-bit read/write register containing
information on pending interrupts, while {\tt sie} is the corresponding
SXLEN-bit read/write register containing interrupt enable bits.
Interrupt cause number \textit{i} (as reported in CSR {\tt scause},
Section~\ref{sec:scause}) corresponds with bit~\textit{i} in both
{\tt sip} and {\tt sie}.
Bits 15:0 are allocated to standard interrupt causes only, while bits 16
and above are available for platform or custom use.
\begin{figure}[h!]
{\footnotesize
\begin{center}
\begin{tabular}{@{}J}
\instbitrange{SXLEN-1}{0} \\
\hline
\multicolumn{1}{|c|}{Interrupts (\warl)} \\
\hline
SXLEN \\
\end{tabular}
\end{center}
}
\vspace{-0.1in}
\caption{Supervisor interrupt-pending register ({\tt sip}).}
\label{sipreg}
\end{figure}
\begin{figure}[h!]
{\footnotesize
\begin{center}
\begin{tabular}{@{}J}
\instbitrange{SXLEN-1}{0} \\
\hline
\multicolumn{1}{|c|}{Interrupts (\warl)} \\
\hline
SXLEN \\
\end{tabular}
\end{center}
}
\vspace{-0.1in}
\caption{Supervisor interrupt-enable register ({\tt sie}).}
\label{siereg}
\end{figure}
An interrupt \textit{i} will be taken if bit \textit{i} is set in both
{\tt sip} and {\tt sie}, and if supervisor-level interrupts are globally
enabled.
Supervisor-level interrupts are globally enabled if the hart's current
privilege mode is less than S, or if the current privilege mode is S
and the SIE bit in the {\tt sstatus} register is set.
Each individual bit in register {\tt sip} may be writable or may be
read-only.
When bit~\textit{i} in {\tt sip} is writable, a pending interrupt
\textit{i} can be cleared by writing 0 to this bit.
If interrupt \textit{i} can become pending but bit~\textit{i} in
{\tt sip} is read-only, the implementation must provide some other
mechanism for clearing the pending interrupt (which may involve a call to
the execution environment).
A bit in {\tt sie} must be writable if the corresponding interrupt can
ever become pending.
Bits of {\tt sie} that are not writable must be hardwired to zero.
The standard portions (bits 15:0) of registers {\tt sip} and {\tt sie}
are formatted as shown in Figures \ref{sipreg-standard} and
\ref{siereg-standard} respectively.
\begin{figure*}[h!]
{\footnotesize
\begin{center}
\setlength{\tabcolsep}{4pt}
\begin{tabular}{ScFcFcc}
\instbitrange{15}{10} &
\instbit{9} &
\instbitrange{8}{6} &
\instbit{5} &
\instbitrange{4}{2} &
\instbit{1} &
\instbit{0} \\
\hline
\multicolumn{1}{|c|}{0} &
\multicolumn{1}{c|}{SEIP} &
\multicolumn{1}{c|}{0} &
\multicolumn{1}{c|}{STIP} &
\multicolumn{1}{c|}{0} &
\multicolumn{1}{c|}{SSIP} &
\multicolumn{1}{c|}{0} \\
\hline
6 & 1 & 3 & 1 & 3 & 1 & 1 \\
\end{tabular}
\end{center}
}
\vspace{-0.1in}
\caption{Standard portion (bits 15:0) of {\tt sip}.}
\label{sipreg-standard}
\end{figure*}
\begin{figure*}[h!]
{\footnotesize
\begin{center}
\setlength{\tabcolsep}{4pt}
\begin{tabular}{ScFcFcc}
\instbitrange{15}{10} &
\instbit{9} &
\instbitrange{8}{6} &
\instbit{5} &
\instbitrange{4}{2} &
\instbit{1} &
\instbit{0} \\
\hline
\multicolumn{1}{|c|}{0} &
\multicolumn{1}{c|}{SEIE} &
\multicolumn{1}{c|}{0} &
\multicolumn{1}{c|}{STIE} &
\multicolumn{1}{c|}{0} &
\multicolumn{1}{c|}{SSIE} &
\multicolumn{1}{c|}{0} \\
\hline
6 & 1 & 3 & 1 & 3 & 1 & 1 \\
\end{tabular}
\end{center}
}
\vspace{-0.1in}
\caption{Standard portion (bits 15:0) of {\tt sie}.}
\label{siereg-standard}
\end{figure*}
Bits {\tt sip}.SEIP and {\tt sie}.SEIE are the interrupt-pending and
interrupt-enable bits for supervisor-level external interrupts.
If implemented, SEIP is read-only in {\tt sip}, and is set and cleared by
the execution environment, typically through a platform-specific
interrupt controller.
Bits {\tt sip}.STIP and {\tt sie}.STIE are the interrupt-pending and
interrupt-enable bits for supervisor-level timer interrupts.
If implemented, STIP is read-only in {\tt sip}, and is set and cleared by
the execution environment.
Bits {\tt sip}.SSIP and {\tt sie}.SSIE are the interrupt-pending and
interrupt-enable bits for supervisor-level software interrupts.
If implemented, SSIP is writable in {\tt sip}.
A supervisor-level software interrupt is triggered
on the current hart by writing 1 to SSIP,
while a pending supervisor-level software
interrupt can be cleared by writing 0 to SSIP.
\begin{commentary}
Interprocessor interrupts are sent to other harts by implementation-specific
means, which will ultimately cause the SSIP bit to be set in the recipient
hart's {\tt sip} register.
\end{commentary}
Each standard interrupt type (SEI, STI, or SSI) may not be implemented,
in which case the corresponding interrupt-pending and interrupt-enable
bits are hardwired to zeros.
All bits in {\tt sip} and {\tt sie} are \warl\ fields.
The implemented interrupts may be found by writing one to every bit
location in {\tt sie}, then reading back to see which bit positions hold
a one.
\begin{commentary}
The {\tt sip} and {\tt sie} registers are subsets of the {\tt mip} and {\tt
mie} registers. Reading any implemented field,
or writing any writable field, of {\tt sip}/{\tt sie}
effects a read or write of the homonymous field of {\tt mip}/{\tt mie}.
Bits 3, 7, and 11 of {\tt sip} and {\tt sie} correspond to the machine-mode
software, timer, and external interrupts, respectively. Since most platforms
will choose not to make these interrupts delegatable from M-mode to S-mode,
they are shown as hardwired to 0 in Figures~\ref{sipreg-standard} and
\ref{siereg-standard}.
\end{commentary}
Multiple simultaneous
interrupts destined for supervisor mode are handled in the following
decreasing priority order: SEI, SSI, STI.
Synchronous exceptions are of lower priority than all interrupts.
\subsection{Supervisor Timers and Performance Counters}
Supervisor software uses the same hardware performance monitoring facility
as user-mode software, including the {\tt time}, {\tt cycle}, and {\tt instret}
CSRs. The implementation should provide a mechanism to modify the
counter values.
The implementation must provide a facility for scheduling timer interrupts in
terms of the real-time counter, {\tt time}.
\subsection{Counter-Enable Register ({\tt scounteren})}
\begin{figure*}[h!]
{\footnotesize
\begin{center}
\setlength{\tabcolsep}{4pt}
\begin{tabular}{cccMcccccc}
\instbit{31} &
\instbit{30} &
\instbit{29} &
\instbitrange{28}{6} &
\instbit{5} &
\instbit{4} &
\instbit{3} &
\instbit{2} &
\instbit{1} &
\instbit{0} \\
\hline
\multicolumn{1}{|c|}{HPM31} &
\multicolumn{1}{c|}{HPM30} &
\multicolumn{1}{c|}{HPM29} &
\multicolumn{1}{c|}{...} &
\multicolumn{1}{c|}{HPM5} &
\multicolumn{1}{c|}{HPM4} &
\multicolumn{1}{c|}{HPM3} &
\multicolumn{1}{c|}{IR} &
\multicolumn{1}{c|}{TM} &
\multicolumn{1}{c|}{CY} \\
\hline
1 & 1 & 1 & 23 & 1 & 1 & 1 & 1 & 1 & 1 \\
\end{tabular}
\end{center}
}
\vspace{-0.1in}
\caption{Counter-enable register ({\tt scounteren}).}
\label{scounteren}
\end{figure*}
The counter-enable register {\tt scounteren} is a 32-bit register that
controls the availability of the hardware performance monitoring counters to
U-mode.
When the CY, TM, IR, or HPM{\em n} bit in the {\tt scounteren} register is
clear, attempts to read the {\tt cycle}, {\tt time}, {\tt instret}, or
{\tt hpmcounter{\em n}} register while executing in U-mode
will cause an illegal instruction exception. When one of these bits is set,
access to the corresponding register is permitted.
{\tt scounteren} must be implemented. However, any of the bits may contain
a hardwired value of zero, indicating reads to the corresponding counter will
cause an exception when executing in U-mode.
Hence, they are effectively \warl\ fields.
\subsection{Supervisor Scratch Register ({\tt sscratch})}
The {\tt sscratch} register is an SXLEN-bit read/write register,
dedicated for use by the supervisor. Typically, {\tt sscratch} is
used to hold a pointer to the hart-local supervisor context while the
hart is executing user code. At the beginning of a trap handler, {\tt
sscratch} is swapped with a user register to provide an initial
working register.
\begin{figure}[h!]
{\footnotesize
\begin{center}
\begin{tabular}{@{}J}
\instbitrange{SXLEN-1}{0} \\
\hline
\multicolumn{1}{|c|}{\tt sscratch} \\
\hline
SXLEN \\
\end{tabular}
\end{center}
}
\vspace{-0.1in}
\caption{Supervisor Scratch Register.}
\label{kregs}
\end{figure}
\subsection{Supervisor Exception Program Counter ({\tt sepc})}
{\tt sepc} is an SXLEN-bit read/write register formatted as shown in
Figure~\ref{epcreg}. The low bit of {\tt sepc} ({\tt sepc[0]}) is
always zero. On implementations that support only IALIGN=32, the two low bits
({\tt sepc[1:0]}) are always zero.
If an implementation allows IALIGN to be either 16 or 32 (by
changing CSR {\tt misa}, for example), then, whenever IALIGN=32, bit
{\tt sepc[1]} is masked on reads so that it appears to be 0. This
masking occurs also for the implicit read by the SRET instruction.
Though masked, {\tt sepc[1]} remains writable when IALIGN=32.
{\tt sepc} is a \warl\ register that must be able to hold all valid
virtual addresses. It need not be capable of holding all possible invalid
addresses. Implementations may convert some invalid address patterns into
other invalid addresses prior to writing them to {\tt sepc}.
When a trap is taken into S-mode, {\tt sepc} is written with the
virtual address of the instruction that was interrupted or that
encountered the exception. Otherwise, {\tt sepc} is never written by
the implementation, though it may be explicitly written by software.
\begin{figure}[h!]
{\footnotesize
\begin{center}
\begin{tabular}{@{}J}
\instbitrange{SXLEN-1}{0} \\
\hline
\multicolumn{1}{|c|}{\tt sepc} \\
\hline
SXLEN \\
\end{tabular}
\end{center}
}
\vspace{-0.1in}
\caption{Supervisor exception program counter register.}
\label{epcreg}
\end{figure}
\subsection{Supervisor Cause Register ({\tt scause})}
\label{sec:scause}
The {\tt scause} register is an SXLEN-bit read-write register formatted as
shown in Figure~\ref{scausereg}. When a trap is taken into S-mode, {\tt
scause} is written with a code indicating the event that caused the trap.
Otherwise, {\tt scause} is never written by the implementation, though it may be
explicitly written by software.
The Interrupt bit in the {\tt scause} register is set if the
trap was caused by an interrupt. The Exception Code field
contains a code identifying the last exception. Table~\ref{scauses}
lists the possible exception codes for the current supervisor ISAs.
The Exception Code is a \wlrl\ field. It is required to hold
the values 0--31 (i.e., bits 4--0 must be implemented), but otherwise
it is only guaranteed to hold supported exception codes.
\begin{figure*}[h!]
{\footnotesize
\begin{center}
\begin{tabular}{c@{}U}
\instbit{SXLEN-1} &
\instbitrange{SXLEN-2}{0} \\
\hline
\multicolumn{1}{|c|}{Interrupt} &
\multicolumn{1}{c|}{Exception Code (\wlrl)} \\
\hline
1 & SXLEN-1 \\
\end{tabular}
\end{center}
}
\vspace{-0.1in}
\caption{Supervisor Cause register {\tt scause}.}
\label{scausereg}
\end{figure*}
\begin{table*}[h!]
\begin{center}
\begin{tabular}{|r|r|l|l|}
\hline
Interrupt & Exception Code & Description \\
\hline
1 & 0 & {\em Reserved} \\
1 & 1 & Supervisor software interrupt \\
1 & 2--4 & {\em Reserved} \\
1 & 5 & Supervisor timer interrupt \\
1 & 6--8 & {\em Reserved} \\
1 & 9 & Supervisor external interrupt \\
1 & 10--15 & {\em Reserved} \\
1 & $\ge$16 & {\em Available for platform use} \\ \hline
0 & 0 & Instruction address misaligned \\
0 & 1 & Instruction access fault \\
0 & 2 & Illegal instruction \\
0 & 3 & Breakpoint \\
0 & 4 & Load address misaligned \\
0 & 5 & Load access fault \\
0 & 6 & Store/AMO address misaligned \\
0 & 7 & Store/AMO access fault \\
0 & 8 & Environment call from U-mode \\
0 & 9 & Environment call from S-mode \\
0 & 10--11 & {\em Reserved} \\
0 & 12 & Instruction page fault \\
0 & 13 & Load page fault \\
0 & 14 & {\em Reserved} \\
0 & 15 & Store/AMO page fault \\
0 & 16--23 & {\em Reserved} \\
0 & 24--31 & {\em Available for custom use} \\
0 & 32--47 & {\em Reserved} \\
0 & 48--63 & {\em Available for custom use} \\
0 & $\ge$64 & {\em Reserved} \\
\hline
\end{tabular}
\end{center}
\caption{Supervisor cause register ({\tt scause}) values after trap.
Synchronous exception priorities are given by Table~\ref{exception-priority}.}
\label{scauses}
\end{table*}
\subsection{Supervisor Trap Value ({\tt stval}) Register}
The {\tt stval} register is an SXLEN-bit read-write register formatted as shown
in Figure~\ref{stvalreg}. When a trap is taken into S-mode, {\tt stval} is
written with exception-specific information to assist software in handling the
trap. Otherwise, {\tt stval} is never written by the implementation, though
it may be explicitly written by software. The hardware platform will specify
which exceptions must set {\tt stval} informatively and which may
unconditionally set it to zero.
When a hardware breakpoint is triggered, or an instruction, load, or
store address-misaligned, access-fault, or page-fault exception occurs, {\tt stval}
is written with the faulting virtual address. On an illegal instruction trap,
{\tt stval} may be written with the first XLEN or ILEN bits of the faulting
instruction as described below. For other exceptions, {\tt stval} is set to
zero, but a future standard may redefine {\tt stval}'s setting for other
exceptions.
\begin{figure}[h!]
{\footnotesize
\begin{center}
\begin{tabular}{@{}J}
\instbitrange{SXLEN-1}{0} \\
\hline
\multicolumn{1}{|c|}{\tt stval} \\
\hline
SXLEN \\
\end{tabular}
\end{center}
}
\vspace{-0.1in}
\caption{Supervisor Trap Value register.}
\label{stvalreg}
\end{figure}
For misaligned loads and stores that cause access-fault or page-fault
exceptions, {\tt stval} will contain the virtual address of the
portion of the access that caused the fault. For
instruction access-fault or page-fault exceptions on systems
with variable-length instructions, {\tt stval} will contain the
virtual address of the portion of the instruction that caused
the fault while {\tt sepc} will point to the beginning of the
instruction.
The {\tt stval} register can optionally also be used to return the
faulting instruction bits on an illegal instruction exception ({\tt
sepc} points to the faulting instruction in memory).
If this feature is not provided, then {\tt stval} is set to zero on
an illegal instruction fault.
If this feature is provided, after an illegal instruction trap, {\tt stval}
will contain the shortest of:
\begin{compactitem}
\item the actual faulting instruction
\item the first ILEN bits of the faulting instruction
\item the first XLEN bits of the faulting instruction
\end{compactitem}
The value loaded into {\tt stval} is right-justified and all unused upper
bits are cleared to zero.
{\tt stval} is a \warl\ register that must be able to hold all valid
virtual addresses and the value 0. It need not be capable of holding all
possible invalid addresses. Implementations may convert some invalid address
patterns into other invalid addresses prior to writing them to {\tt stval}.
If the feature to return the faulting instruction bits is implemented, {\tt
stval} must also be able to hold all values less than $2^N$, where $N$ is the
smaller of XLEN and ILEN.
\subsection{Supervisor Address Translation and Protection ({\tt satp}) Register}
\label{sec:satp}
The {\tt satp} register is an SXLEN-bit read/write register, formatted as shown
in Figure~\ref{rv32satp} for SXLEN=32 and Figure~\ref{rv64satp} for SXLEN=64, which
controls supervisor-mode address translation and protection.
This register holds the physical page number (PPN) of the root page
table, i.e., its supervisor physical address divided by \wunits{4}{KiB};
an address space identifier (ASID), which facilitates address-translation
fences on a per-address-space basis; and the MODE field, which selects the
current address-translation scheme. Further details on the access to this
register are described in Section~\ref{virt-control}.
\begin{figure}[h!]
{\footnotesize
\begin{center}
\begin{tabular}{c@{}E@{}K}
\instbit{31} &
\instbitrange{30}{22} &
\instbitrange{21}{0} \\
\hline
\multicolumn{1}{|c|}{{\tt MODE} (\warl)} &
\multicolumn{1}{|c|}{{\tt ASID} (\warl)} &
\multicolumn{1}{|c|}{{\tt PPN} (\warl)} \\
\hline
1 & 9 & 22 \\
\end{tabular}
\end{center}
}
\vspace{-0.1in}
\caption{RV32 Supervisor address translation and protection register {\tt satp}.}
\label{rv32satp}
\end{figure}
\begin{commentary}
Storing a PPN in {\tt satp}, rather than a physical address, supports
a physical address space larger than \wunits{4}{GiB} for RV32.
\end{commentary}
\begin{figure}[h!]
{\footnotesize
\begin{center}
\begin{tabular}{@{}S@{}T@{}U}
\instbitrange{63}{60} &
\instbitrange{59}{44} &
\instbitrange{43}{0} \\
\hline
\multicolumn{1}{|c|}{{\tt MODE} (\warl)} &
\multicolumn{1}{|c|}{{\tt ASID} (\warl)} &
\multicolumn{1}{|c|}{{\tt PPN} (\warl)} \\
\hline
4 & 16 & 44 \\
\end{tabular}
\end{center}
}
\vspace{-0.1in}
\caption{RV64 Supervisor address translation and protection register {\tt satp}, for MODE
values Bare, Sv39, and Sv48.}
\label{rv64satp}
\end{figure}
\begin{samepage-commentary}
We store the ASID and the page table base address in the same CSR to allow the
pair to be changed atomically on a context switch. Swapping them
non-atomically could pollute the old virtual address space with new
translations, or vice-versa. This approach also slightly reduces the cost of
a context switch.
\end{samepage-commentary}
Table~\ref{tab:satp-mode} shows the encodings of the MODE field for RV32 and
RV64. When MODE=Bare, supervisor virtual addresses are equal to
supervisor physical addresses, and there is no additional memory protection
beyond the physical memory protection scheme described in
Section~\ref{sec:pmp}. In this case, the remaining fields in {\tt satp}
have no effect.
For RV32, the only other valid setting for MODE is Sv32, a paged
virtual-memory scheme described in Section~\ref{sec:sv32}.
For RV64, two paged virtual-memory schemes are defined: Sv39 and Sv48,
described in Sections~\ref{sec:sv39} and \ref{sec:sv48}, respectively.
Two additional schemes, Sv57 and Sv64, will be defined in a later version
of this specification. The remaining MODE settings are reserved
for future use and may define different interpretations of the other fields in
{\tt satp}.
Implementations are not required to support all MODE settings,
and if {\tt satp} is written with an unsupported MODE, the entire write has
no effect; no fields in {\tt satp} are modified.
\begin{table}[h]
\begin{center}
\begin{tabular}{|c|c|l|}
\hline
\multicolumn{3}{|c|}{RV32} \\
\hline
Value & Name & Description \\
\hline
0 & Bare & No translation or protection. \\
1 & Sv32 & Page-based 32-bit virtual addressing (see Section~\ref{sec:sv32}). \\
\hline \hline
\multicolumn{3}{|c|}{RV64} \\
\hline
Value & Name & Description \\
\hline
0 & Bare & No translation or protection. \\
1--7 & --- & {\em Reserved} \\
8 & Sv39 & Page-based 39-bit virtual addressing (see Section~\ref{sec:sv39}). \\
9 & Sv48 & Page-based 48-bit virtual addressing (see Section~\ref{sec:sv48}). \\
10 & {\em Sv57} & {\em Reserved for page-based 57-bit virtual addressing.} \\
11 & {\em Sv64} & {\em Reserved for page-based 64-bit virtual addressing.} \\
12--15 & --- & {\em Reserved} \\
\hline
\end{tabular}
\end{center}
\caption{Encoding of {\tt satp} MODE field.}
\label{tab:satp-mode}
\end{table}
The number of supervisor physical address bits is implementation-defined; any
unimplemented address bits are hardwired to zero in the {\tt satp} register.
The number of ASID bits is also implementation-defined and may be zero. The
number of implemented ASID bits, termed {\mbox {\em ASIDLEN}}, may be
determined by writing one to every bit position in the ASID field, then
reading back the value in {\tt satp} to see which bit positions in the ASID
field hold a one. The least-significant bits of ASID are implemented first:
that is, if ASIDLEN~$>$~0, ASID[ASIDLEN-1:0] is writable. The maximal value
of ASIDLEN, termed ASIDMAX, is 9 for Sv32 or 16 for Sv39 and Sv48.
\begin{commentary}
For many applications, the choice of page size has a substantial
performance impact. A large page size increases TLB reach and loosens
the associativity constraints on virtually-indexed, physically-tagged
caches. At the same time, large pages exacerbate internal
fragmentation, wasting physical memory and possibly cache capacity.
After much deliberation, we have settled on a conventional page size
of 4 KiB for both RV32 and RV64. We expect this decision to ease the
porting of low-level runtime software and device drivers. The TLB
reach problem is ameliorated by transparent superpage support in
modern operating systems~\cite{transparent-superpages}. Additionally,
multi-level TLB hierarchies are quite inexpensive relative to the
multi-level cache hierarchies whose address space they map.
\end{commentary}
Note that writing {\tt satp} does not imply any ordering constraints
between page-table updates and subsequent address translations.
If the new address space's page tables have been modified, or if an
ASID is reused, it may be necessary to execute an SFENCE.VMA instruction
(see Section~\ref{sec:sfence.vma}) after writing {\tt satp}.
\begin{commentary}
Not imposing upon implementations to flush address-translation caches
upon {\tt satp} writes reduces the cost of context switches, provided
a sufficiently large ASID space.
\end{commentary}
\section{Supervisor Instructions}
In addition to the SRET instruction defined in
Section~\ref{otherpriv}, one new supervisor-level instruction is
provided.
\subsection{Supervisor Memory-Management Fence Instruction}
\label{sec:sfence.vma}
\vspace{-0.2in}
\begin{center}
\begin{tabular}{O@{}R@{}R@{}F@{}R@{}S}
\\
\instbitrange{31}{25} &
\instbitrange{24}{20} &
\instbitrange{19}{15} &
\instbitrange{14}{12} &
\instbitrange{11}{7} &
\instbitrange{6}{0} \\
\hline
\multicolumn{1}{|c|}{funct7} &
\multicolumn{1}{c|}{rs2} &
\multicolumn{1}{c|}{rs1} &
\multicolumn{1}{c|}{funct3} &
\multicolumn{1}{c|}{rd} &
\multicolumn{1}{c|}{opcode} \\
\hline
7 & 5 & 5 & 3 & 5 & 7 \\
SFENCE.VMA & asid & vaddr & PRIV & 0 & SYSTEM \\
\end{tabular}
\end{center}
The supervisor memory-management fence instruction SFENCE.VMA is used to
synchronize updates to in-memory memory-management data structures with
current execution. Instruction execution causes implicit reads and writes to
these data structures; however, these implicit references are ordinarily not
ordered with respect to explicit loads and stores. Executing
an SFENCE.VMA instruction guarantees that any previous stores already visible
to the current RISC-V hart are ordered before all subsequent implicit references
from that hart to the memory-management data structures.
Further details on the behavior of this instruction are
described in Section~\ref{virt-control} and Section~\ref{pmp-vmem}.
\begin{commentary}
The SFENCE.VMA is used to flush any local hardware caches related to
address translation. It is specified as a fence rather than a TLB
flush to provide cleaner semantics with respect to which instructions
are affected by the flush operation and to support a wider variety of
dynamic caching structures and memory-management schemes. SFENCE.VMA
is also used by higher privilege levels to synchronize page table
writes and the address translation hardware.
\end{commentary}
SFENCE.VMA orders only the local hart's implicit references to the
memory-management data structures.
\begin{commentary}
Consequently, other harts must be notified separately when the
memory-management data structures have been modified.
One approach is to use 1)
a local data fence to ensure local writes are visible globally, then
2) an interprocessor interrupt to the other thread, then 3) a local
SFENCE.VMA in the interrupt handler of the remote thread, and finally
4) signal back to originating thread that operation is complete. This
is, of course, the RISC-V analog to a TLB shootdown.
\end{commentary}
For the common case that the translation data structures have only been
modified for a single address mapping (i.e., one page or superpage), {\em rs1}
can specify a virtual address within that mapping to effect a translation
fence for that mapping only. Furthermore, for the common case that the
translation data structures have only been modified for a single address-space
identifier, {\em rs2} can specify the address space. The behavior of
SFENCE.VMA depends on {\em rs1} and {\em rs2} as follows:
\begin{itemize}
\item If {\em rs1}={\tt x0} and {\em rs2}={\tt x0}, the fence orders all
reads and writes made to any level of the page tables, for all
address spaces.
\item If {\em rs1}={\tt x0} and {\em rs2}$\neq${\tt x0}, the fence orders
all reads and writes made to any level of the page tables, but only
for the address space identified by integer register {\em rs2}.
Accesses to {\em global} mappings (see Section~\ref{sec:translation})
are not ordered.
\item If {\em rs1}$\neq${\tt x0} and {\em rs2}={\tt x0}, the fence orders
only reads and writes made to the leaf page table entry corresponding
to the virtual address in {\em rs1}, for all address spaces.
\item If {\em rs1}$\neq${\tt x0} and {\em rs2}$\neq${\tt x0}, the fence
orders only reads and writes made to the leaf page table entry
corresponding to the virtual address in {\em rs1}, for the address
space identified by integer register {\em rs2}.
Accesses to global mappings are not ordered.
\end{itemize}
When {\em rs2}$\neq${\tt x0}, bits SXLEN-1:ASIDMAX of the value held in {\em
rs2} are reserved for future use and should be zeroed by software and ignored
by current implementations. Furthermore, if ASIDLEN~$<$~ASIDMAX, the
implementation shall ignore bits ASIDMAX-1:ASIDLEN of the value held in {\em
rs2}.
\begin{commentary}
Simpler implementations can ignore the virtual address in {\em rs1} and
the ASID value in {\em rs2} and always perform a global fence.
\end{commentary}
Implementations may perform implicit reads of the translation data structures
pointed to by the current {\tt satp} register arbitrarily early and
speculatively. The results of these reads may be held in an incoherent cache
but not shared with other harts. Cache entries may only be established for
the ASID currently loaded into the {\tt satp} register, or for global entries.
The cache may only satisfy implicit reads for entries that have been
established for the ASID currently loaded into {\tt satp}, or for global
entries. Changes in the {\tt satp} register do not necessarily flush any such
translation caches. To ensure the implicit reads observe writes to the same
memory locations, an SFENCE.VMA instruction must be executed after the writes
to flush the relevant cached translations.
Implementations must only perform implicit reads of the translation
data structures pointed to by the current contents of the {\tt satp}
register, and must only raise exceptions for implicit accesses that are
generated as a result of instruction execution, not those that are
performed speculatively.
\begin{commentary}
The following common situations typically require executing an
SFENCE.VMA instruction:
\vspace{-0.1in}
\begin{itemize}
\item When software recycles an ASID (i.e., reassociates it with a different
page table), it should {\em first} change {\tt satp} to point to the new page
table using the recycled ASID, {\em then} execute SFENCE.VMA with {\em
rs1}={\tt x0} and {\em rs2} set to the recycled ASID. Alternatively, software
can execute the same SFENCE.VMA instruction while a different ASID is loaded
into {\tt satp}, provided the next time {\tt satp} is loaded with the recycled
ASID, it is simultaneously loaded with the new page table.
\item If the implementation does not provide ASIDs, or software chooses to
always use ASID 0, then after every {\tt satp} write, software should execute
SFENCE.VMA with {\em rs1}={\tt x0}. In the common case that no global
translations have been modified, {\em rs2} should be set to a register other than
{\tt x0} but which contains the value zero, so that global translations are
not flushed.
\item If software modifies a non-leaf PTE, it should execute SFENCE.VMA with
{\em rs1}={\tt x0}. If any PTE along the traversal path had its G bit set,
{\em rs2} must be {\tt x0}; otherwise, {\em rs2} should be set to the ASID for
which the translation is being modified.
\item If software modifies a leaf PTE, it should execute SFENCE.VMA with {\em
rs1} set to a virtual address within the page. If any PTE along the traversal
path had its G bit set, {\em rs2} must be {\tt x0}; otherwise, {\em rs2}
should be set to the ASID for which the translation is being modified.
\item For the special cases of increasing the permissions on a leaf PTE and
changing an invalid PTE to a valid leaf, software may choose to execute
the SFENCE.VMA lazily. After modifying the PTE but before executing
SFENCE.VMA, either the new or old permissions will be used. In the latter
case, a page-fault exception might occur, at which point software should
execute SFENCE.VMA in accordance with the previous bullet point.
\end{itemize}
\end{commentary}
For forward compatibility with future versions of this specification,
supervisor software should adhere to the following constraints on ASID usage.
Supervisor software that uses ASIDs should use a nonzero ASID value to refer to
the same address space across all harts in the SEE and should not use an ASID
value of 0. Supervisor software that does not use ASIDs should always set the
ASID field in the {\tt satp} CSR to 0.
\begin{commentary}
A future extension may define ASIDs to be global across the SEE, facilitating
such optimizations as multicast TLB shootdown and sharing translation caches
between harts.
The extension will provide a mechanism so that existing supervisor software
that always uses ASID 0 will continue to function as it currently does.
\end{commentary}
\section{Sv32: Page-Based 32-bit Virtual-Memory Systems}
\label{sec:sv32}
When Sv32 is written to the MODE field in the {\tt satp} register (see
Section~\ref{sec:satp}), the supervisor operates in a 32-bit paged
virtual-memory system. In this mode, supervisor and user virtual addresses
are translated into supervisor physical addresses by traversing a radix-tree
page table. Sv32 is supported on RV32 systems and is designed to include
mechanisms sufficient for supporting modern Unix-based operating systems.
\begin{commentary}
The initial RISC-V paged virtual-memory architectures have been
designed as straightforward implementations to support existing
operating systems. We have architected page table layouts to support
a hardware page-table walker. Software TLB refills are a performance
bottleneck on high-performance systems, and are especially troublesome
with decoupled specialized coprocessors. An implementation can choose
to implement software TLB refills using a machine-mode trap handler as
an extension to M-mode.
\end{commentary}
\subsection{Addressing and Memory Protection}
\label{sec:translation}
Sv32 implementations support a 32-bit virtual address space, divided
into \wunits{4}{KiB} pages. An Sv32 virtual address is partitioned
into a virtual page number (VPN) and page offset, as shown in
Figure~\ref{sv32va}. When Sv32 virtual memory mode is selected in the
MODE field of the {\tt satp} register, supervisor virtual addresses
are translated into supervisor physical addresses via a two-level page
table. The 20-bit VPN is translated into a 22-bit physical page
number (PPN), while the 12-bit page offset is untranslated. The
resulting supervisor-level physical addresses are then checked using
any physical memory protection structures (Sections~\ref{sec:pmp}),
before being directly converted to machine-level physical addresses.
\begin{figure*}[h!]
{\footnotesize
\begin{center}
\begin{tabular}{@{}O@{}O@{}E}
\instbitrange{31}{22} &
\instbitrange{21}{12} &
\instbitrange{11}{0} \\
\hline
\multicolumn{1}{|c|}{VPN[1]} &
\multicolumn{1}{c|}{VPN[0]} &
\multicolumn{1}{c|}{page offset} \\
\hline
10 & 10 & 12 \\
\end{tabular}
\end{center}
}
\vspace{-0.1in}
\caption{Sv32 virtual address.}
\label{sv32va}
\end{figure*}
\begin{figure*}[h!]
{\footnotesize
\begin{center}
\begin{tabular}{@{}E@{}O@{}E}
\instbitrange{33}{22} &
\instbitrange{21}{12} &
\instbitrange{11}{0} \\
\hline
\multicolumn{1}{|c|}{PPN[1]} &
\multicolumn{1}{c|}{PPN[0]} &
\multicolumn{1}{c|}{page offset} \\
\hline
12 & 10 & 12 \\
\end{tabular}
\end{center}
}
\vspace{-0.1in}
\caption{Sv32 physical address.}
\label{rv32va}
\end{figure*}
\begin{figure*}[h!]
{\footnotesize
\begin{center}
\begin{tabular}{@{}E@{}O@{}Fcccccccc}
\instbitrange{31}{20} &
\instbitrange{19}{10} &
\instbitrange{9}{8} &
\instbit{7} &
\instbit{6} &
\instbit{5} &
\instbit{4} &
\instbit{3} &
\instbit{2} &
\instbit{1} &
\instbit{0} \\
\hline
\multicolumn{1}{|c|}{PPN[1]} &
\multicolumn{1}{c|}{PPN[0]} &
\multicolumn{1}{c|}{RSW} &
\multicolumn{1}{c|}{D} &
\multicolumn{1}{c|}{A} &
\multicolumn{1}{c|}{G} &
\multicolumn{1}{c|}{U} &
\multicolumn{1}{c|}{X} &
\multicolumn{1}{c|}{W} &
\multicolumn{1}{c|}{R} &
\multicolumn{1}{c|}{V} \\
\hline
12 & 10 & 2 & 1 & 1 & 1 & 1 & 1 & 1 & 1 & 1\\
\end{tabular}
\end{center}
}
\vspace{-0.1in}
\caption{Sv32 page table entry.}
\label{sv32pte}
\end{figure*}
Sv32 page tables consist of $2^{10}$ page-table entries (PTEs), each
of four bytes. A page table is exactly the size of a page and must
always be aligned to a page boundary. The physical page number of the
root page table is stored in the {\tt satp} register.
The PTE format for Sv32 is shown in Figures~\ref{sv32pte}. The V bit
indicates whether the PTE is valid; if it is 0, all other bits in the PTE are
don't-cares and may be used freely by software. The permission bits, R, W,
and X, indicate whether the page is readable, writable, and executable,
respectively. When all three are zero, the PTE is a pointer to the next level
of the page table; otherwise, it is a leaf PTE. Writable pages must also be
marked readable; the contrary combinations are reserved for future use.
Table~\ref{pteperm} summarizes the encoding of the permission bits.
\begin{table*}[h!]
\begin{center}
\begin{tabular}{|c|c|c||l|}
\hline
X & W & R & Meaning \\
\hline
0 & 0 & 0 & Pointer to next level of page table. \\
0 & 0 & 1 & Read-only page. \\
0 & 1 & 0 & {\em Reserved for future use.} \\
0 & 1 & 1 & Read-write page. \\
1 & 0 & 0 & Execute-only page. \\
1 & 0 & 1 & Read-execute page. \\
1 & 1 & 0 & {\em Reserved for future use.} \\
1 & 1 & 1 & Read-write-execute page. \\
\hline
\end{tabular}
\end{center}
\caption{Encoding of PTE R/W/X fields.}
\label{pteperm}
\end{table*}
Attempting to fetch an instruction from a page that does not have execute
permissions raises a fetch page-fault exception. Attempting to execute
a load or load-reserved instruction whose effective address lies within
a page without read permissions raises a load page-fault exception.
Attempting to execute a store, store-conditional (regardless of success),
or AMO instruction whose effective address lies within a page without
write permissions raises a store page-fault exception.
\begin{commentary}
AMOs never raise load page-fault exceptions. Since any unreadable page is
also unwritable, attempting to perform an AMO on an unreadable page always
raises a store page-fault exception.
\end{commentary}
The U bit indicates whether the page is accessible to user mode.
U-mode software may only access the page when U=1. If the SUM bit
in the {\tt sstatus} register is
set, supervisor mode software may also access pages with U=1.
However, supervisor code normally operates with the SUM bit clear, in
which case, supervisor code will fault on accesses to user-mode pages.
Irrespective of SUM, the supervisor may not execute code on pages with U=1.
\begin{commentary}
An alternative PTE format would support different permissions for supervisor
and user. We omitted this feature because it would be largely redundant with
the SUM mechanism (see Section~\ref{sec:sum}) and would require more encoding
space in the PTE.
\end{commentary}
The G bit designates a {\em global} mapping. Global mappings are those that
exist in all address spaces. For non-leaf PTEs, the global setting implies
that all mappings in the subsequent levels of the page table are global. Note
that failing to mark a global mapping as global merely reduces performance,
whereas marking a non-global mapping as global is a software bug that,
after switching to an address space with a different non-global mapping for
that address range, can unpredictably result in either mapping being used.
\begin{commentary}
Global mappings need not be stored redundantly in address-translation caches
for multiple ASIDs. Additionally, they need not be flushed from local
address-translation caches when an SFENCE.VMA instruction is executed with
{\em rs2}$\neq${\tt x0}.
\end{commentary}
The RSW field is reserved for use by supervisor software; the implementation
shall ignore this field.
Each leaf PTE contains an accessed (A) and dirty (D) bit. The A bit indicates
the virtual page has been read, written, or fetched from since the last time
the A bit was cleared. The D bit indicates the virtual page has been written
since the last time the D bit was cleared.
Two schemes to manage the A and D bits are permitted:
\begin{itemize}
\item When a virtual page is accessed and the A bit is clear, or is
written and the D bit is clear, a page-fault exception is raised.
\item When a virtual page is accessed and the A bit is clear, or is
written and the D bit is clear, the implementation sets the
corresponding bit(s) in the PTE. The PTE update must be atomic with
respect to other accesses to the PTE, and must atomically check
that the PTE is valid and grants sufficient permissions. The
PTE update must be exact (i.e., not speculative), and observed
in program order by the local hart. Furthermore, the PTE update
must appear in the global memory order no later than the explicit
memory access, or any subsequent explicit memory access to that
virtual page by the local hart. The ordering on loads and stores
provided by FENCE instructions and the acquire/release bits on atomic
instructions also orders the PTE updates associated with those loads
and stores as observed by remote harts.
The PTE update is not required to be atomic with respect to the explicit
memory access that caused the update, and the sequence is interruptible.
However, the hart must not perform the explicit memory access before the
PTE update is globally visible.
\end{itemize}
All harts in a system must employ the same PTE-update scheme as each other.
\begin{commentary}
Mandating that the PTE updates to be exact, atomic, and in program order
simplifies the specification, and makes the feature more useful for system
software. Simple implementations may instead generate page-fault exceptions.
The A and D bits are never cleared by the implementation. If the
supervisor software does not rely on accessed and/or dirty bits,
e.g. if it does not swap memory pages to secondary storage or if the
pages are being used to map I/O space, it should always set them to 1
in the PTE to improve performance.
\end{commentary}
Any level of PTE may be a leaf PTE, so in addition to 4 KiB pages, Sv32
supports 4 MiB {\em megapages}. A megapage must be virtually and
physically aligned to a 4 MiB boundary; a page-fault exception is raised
if the physical address is insufficiently aligned.
For non-leaf PTEs, the D, A, and U bits are reserved for future use and
must be cleared by software for forward compatibility.
For implementations with both page-based virtual memory and the ``A'' standard
extension, the LR/SC reservation set must lie completely within a single
base page (i.e., a naturally aligned \wunits{4}{KiB} region).
\subsection{Virtual Address Translation Process}
\label{sv32algorithm}
A virtual address $va$ is translated into a physical address $pa$ as
follows:
\begin{enumerate}
\item Let $a$ be ${\tt satp}.ppn \times \textrm{PAGESIZE}$, and let $i=\textrm{LEVELS} - 1$. (For Sv32, PAGESIZE=$2^{12}$ and LEVELS=2.)
\item Let $pte$ be the value of the PTE at address
$a+va.vpn[i]\times \textrm{PTESIZE}$. (For Sv32, PTESIZE=4.)
If accessing $pte$ violates a PMA or PMP check, raise an
access-fault exception corresponding to the original access type.
\item If $pte.v=0$, or if $pte.r=0$ and $pte.w=1$, stop and raise a
page-fault exception corresponding to the original access type.
\item Otherwise, the PTE is valid.
If $pte.r=1$ or $pte.x=1$, go to step 5.
Otherwise, this PTE is a pointer to the next level of the page table. Let
$i=i-1$. If $i<0$, stop and raise a page-fault exception
corresponding to the original access type. Otherwise, let
$a=pte.ppn \times \textrm{PAGESIZE}$ and go to step 2.
\item A leaf PTE has been found. Determine if the requested memory access is
allowed by the $pte.r$, $pte.w$, $pte.x$, and $pte.u$ bits, given the
current privilege mode and the value of the SUM and MXR fields of
the {\tt mstatus} register. If not, stop and raise a page-fault
exception corresponding to the original access type.
\item If $i>0$ and $pte.ppn[i-1:0]\neq 0$, this is a misaligned superpage;
stop and raise a page-fault exception corresponding to the original access type.
\item If $pte.a=0$, or if the memory access is a store and $pte.d=0$, either
raise a page-fault exception corresponding to the original access type, or:
\begin{itemize}
\item Set $pte.a$ to 1 and, if the memory access is a store, also set
$pte.d$ to 1.
\item If this access violates a PMA or PMP check, raise an access-fault exception
corresponding to the original access type.
\item This update and the loading of $pte$ in step 2 must be atomic; in
particular, no intervening store to the PTE may be perceived to have
occurred in-between.
\end{itemize}
\item The translation is successful. The translated physical address is
given as follows:
\begin{itemize}
\item $\textit{pa.pgoff} = \textit{va.pgoff}$.
\item If $i>0$, then this is a superpage translation and $pa.ppn[i-1:0]=va.vpn[i-1:0]$.
\item $pa.ppn[\textrm{LEVELS} - 1:i] = pte.ppn[\textrm{LEVELS} - 1:i]$.
\end{itemize}
\end{enumerate}
\section{Sv39: Page-Based 39-bit Virtual-Memory System}
\label{sec:sv39}
This section describes a simple paged virtual-memory system designed
for RV64 systems, which supports 39-bit virtual address spaces. The
design of Sv39 follows the overall scheme of Sv32, and this section
details only the differences between the schemes.
\begin{commentary}
We specified multiple virtual memory systems for RV64 to relieve the tension
between providing a large address space and minimizing address-translation
cost. For many systems, \wunits{512}{GiB} of virtual-address space is ample,
and so Sv39 suffices. Sv48 increases the virtual address space to
\wunits{256}{TiB}, but increases the physical memory
capacity dedicated to page tables, the latency of page-table traversals, and
the size of hardware structures that store virtual addresses.
\end{commentary}
\subsection{Addressing and Memory Protection}
Sv39 implementations support a 39-bit virtual address space, divided
into \wunits{4}{KiB} pages. An Sv39 address is partitioned as
shown in Figure~\ref{sv39va}.
Instruction fetch addresses and load and store effective addresses,
which are 64 bits, must have bits 63--39 all equal to bit 38, or else
a page-fault exception will occur. The 27-bit VPN is translated into a
44-bit PPN via a three-level page table, while the 12-bit page offset
is untranslated.
\begin{commentary}
When mapping between narrower and wider addresses, RISC-V usually
zero-extends a narrower address to a wider size. The mapping
between 64-bit virtual addresses and the 39-bit usable address
space of Sv39 is not based on zero-extension but instead follows an
entrenched convention that allows an OS to use one or a few of the
most-significant bits of a full-size (64-bit) virtual address to
quickly distinguish user and supervisor address regions.
\end{commentary}
\begin{figure*}[h!]
{\footnotesize
\begin{center}
\begin{tabular}{@{}O@{}O@{}O@{}O}
\instbitrange{38}{30} &
\instbitrange{29}{21} &
\instbitrange{20}{12} &
\instbitrange{11}{0} \\
\hline
\multicolumn{1}{|c|}{VPN[2]} &
\multicolumn{1}{c|}{VPN[1]} &
\multicolumn{1}{c|}{VPN[0]} &
\multicolumn{1}{c|}{page offset} \\
\hline
9 & 9 & 9 & 12 \\
\end{tabular}
\end{center}
}
\vspace{-0.1in}
\caption{Sv39 virtual address.}
\label{sv39va}
\end{figure*}
\begin{figure*}[h!]
{\footnotesize
\begin{center}
\begin{tabular}{@{}T@{}O@{}O@{}O}
\instbitrange{55}{30} &
\instbitrange{29}{21} &
\instbitrange{20}{12} &
\instbitrange{11}{0} \\
\hline
\multicolumn{1}{|c|}{PPN[2]} &
\multicolumn{1}{c|}{PPN[1]} &
\multicolumn{1}{c|}{PPN[0]} &
\multicolumn{1}{c|}{page offset} \\
\hline
26 & 9 & 9 & 12 \\
\end{tabular}
\end{center}
}
\vspace{-0.1in}
\caption{Sv39 physical address.}
\label{sv39pa}
\end{figure*}
\begin{figure*}[h!]
{\footnotesize
\begin{center}
\begin{tabular}{@{}Y@{}Y@{}Y@{}Y@{}Fcccccccc}
\instbitrange{63}{54} &
\instbitrange{53}{28} &
\instbitrange{27}{19} &
\instbitrange{18}{10} &
\instbitrange{9}{8} &
\instbit{7} &
\instbit{6} &
\instbit{5} &
\instbit{4} &
\instbit{3} &
\instbit{2} &
\instbit{1} &
\instbit{0} \\
\hline
\multicolumn{1}{|c|}{\it Reserved} &
\multicolumn{1}{c|}{PPN[2]} &
\multicolumn{1}{c|}{PPN[1]} &
\multicolumn{1}{c|}{PPN[0]} &
\multicolumn{1}{c|}{RSW} &
\multicolumn{1}{c|}{D} &
\multicolumn{1}{c|}{A} &
\multicolumn{1}{c|}{G} &
\multicolumn{1}{c|}{U} &
\multicolumn{1}{c|}{X} &
\multicolumn{1}{c|}{W} &
\multicolumn{1}{c|}{R} &
\multicolumn{1}{c|}{V} \\
\hline
10 & 26 & 9 & 9 & 2 & 1 & 1 & 1 & 1 & 1 & 1 & 1 & 1\\
\end{tabular}
\end{center}
}
\vspace{-0.1in}
\caption{Sv39 page table entry.}
\label{sv39pte}
\end{figure*}
Sv39 page tables contain $2^9$ page table entries (PTEs), eight
bytes each. A page table is exactly the size of a page and must
always be aligned to a page boundary. The physical page number of the
root page table is stored in the {\tt satp} register's PPN field.
The PTE format for Sv39 is shown in Figure~\ref{sv39pte}. Bits 9--0
have the same meaning as for Sv32. Bits 63--54 are reserved
for future use and must be zeroed by software for forward compatibility.
\begin{commentary}
We reserved several PTE bits for a possible extension that improves
support for sparse address spaces by allowing page-table levels to be
skipped, reducing memory usage and TLB refill latency. These reserved
bits may also be used to facilitate research experimentation. The
cost is reducing the physical address space, but \wunits{64}{PiB} is
presently ample. When it no longer suffices, the reserved
bits that remain unallocated could be used to expand the physical
address space.
\end{commentary}
Any level of PTE may be a leaf PTE, so in addition to \wunits{4}{KiB}
pages, Sv39 supports \wunits{2}{MiB} {\em megapages} and
\wunits{1}{GiB} {\em gigapages}, each of which must be virtually and
physically aligned to a boundary equal to its size.
A page-fault exception is raised if the physical address is insufficiently
aligned.
The algorithm for virtual-to-physical address translation is the same as in
Section~\ref{sv32algorithm}, except LEVELS equals 3 and PTESIZE equals 8.
\section{Sv48: Page-Based 48-bit Virtual-Memory System}
\label{sec:sv48}
This section describes a simple paged virtual-memory system designed
for RV64 systems, which supports 48-bit virtual address spaces. Sv48
is intended for systems for which a 39-bit virtual address space is
insufficient. It closely follows the design of Sv39, simply adding an
additional level of page table, and so this chapter only details the
differences between the two schemes.
Implementations that support Sv48 must also support Sv39.
\begin{commentary}
Systems that support Sv48 can also support Sv39 at essentially no cost, and so
should do so to maintain compatibility with supervisor software that assumes
Sv39.
\end{commentary}
\subsection{Addressing and Memory Protection}
Sv48 implementations support a 48-bit virtual address space, divided
into \wunits{4}{KiB} pages. An Sv48 address is partitioned as
shown in Figure~\ref{sv48va}.
Instruction fetch addresses and load and store effective addresses,
which are 64 bits, must have bits 63--48 all equal to bit 47, or else
a page-fault exception will occur. The 36-bit VPN is translated into a
44-bit PPN via a four-level page table, while the 12-bit page offset
is untranslated.
\begin{figure*}[h!]
{\footnotesize
\begin{center}
\begin{tabular}{@{}O@{}O@{}O@{}O@{}O}
\instbitrange{47}{39} &
\instbitrange{38}{30} &
\instbitrange{29}{21} &
\instbitrange{20}{12} &
\instbitrange{11}{0} \\
\hline
\multicolumn{1}{|c|}{VPN[3]} &
\multicolumn{1}{c|}{VPN[2]} &
\multicolumn{1}{c|}{VPN[1]} &
\multicolumn{1}{c|}{VPN[0]} &
\multicolumn{1}{c|}{page offset} \\
\hline
9 & 9 & 9 & 9 & 12 \\
\end{tabular}
\end{center}
}
\vspace{-0.1in}
\caption{Sv48 virtual address.}
\label{sv48va}
\end{figure*}
\begin{figure*}[h!]
{\footnotesize
\begin{center}
\begin{tabular}{@{}E@{}O@{}O@{}O@{}O}
\instbitrange{55}{39} &
\instbitrange{38}{30} &
\instbitrange{29}{21} &
\instbitrange{20}{12} &
\instbitrange{11}{0} \\
\hline
\multicolumn{1}{|c|}{PPN[3]} &
\multicolumn{1}{c|}{PPN[2]} &
\multicolumn{1}{c|}{PPN[1]} &
\multicolumn{1}{c|}{PPN[0]} &
\multicolumn{1}{c|}{page offset} \\
\hline
17 & 9 & 9 & 9 & 12 \\
\end{tabular}
\end{center}
}
\vspace{-0.1in}
\caption{Sv48 physical address.}
\label{sv48pa}
\end{figure*}
\begin{figure*}[h!]
{\footnotesize
\begin{center}
\begin{tabular}{@{}Y@{}Y@{}Y@{}Y@{}Y@{}Fcccccccc}
\instbitrange{63}{54} &
\instbitrange{53}{37} &
\instbitrange{36}{28} &
\instbitrange{27}{19} &
\instbitrange{18}{10} &
\instbitrange{9}{8} &
\instbit{7} &
\instbit{6} &
\instbit{5} &
\instbit{4} &
\instbit{3} &
\instbit{2} &
\instbit{1} &
\instbit{0} \\
\hline
\multicolumn{1}{|c|}{\it Reserved} &
\multicolumn{1}{c|}{PPN[3]} &
\multicolumn{1}{c|}{PPN[2]} &
\multicolumn{1}{c|}{PPN[1]} &
\multicolumn{1}{c|}{PPN[0]} &
\multicolumn{1}{c|}{RSW} &
\multicolumn{1}{c|}{D} &
\multicolumn{1}{c|}{A} &
\multicolumn{1}{c|}{G} &
\multicolumn{1}{c|}{U} &
\multicolumn{1}{c|}{X} &
\multicolumn{1}{c|}{W} &
\multicolumn{1}{c|}{R} &
\multicolumn{1}{c|}{V} \\
\hline
10 & 17 & 9 & 9 & 9 & 2 & 1 & 1 & 1 & 1 & 1 & 1 & 1 & 1\\
\end{tabular}
\end{center}
}
\vspace{-0.1in}
\caption{Sv48 page table entry.}
\label{sv48pte}
\end{figure*}
The PTE format for Sv48 is shown in Figure~\ref{sv48pte}. Bits 9--0
have the same meaning as for Sv32. Any level of PTE may be a leaf
PTE, so in addition to \wunits{4}{KiB} pages, Sv48 supports
\wunits{2}{MiB} {\em megapages}, \wunits{1}{GiB} {\em gigapages}, and
\wunits{512}{GiB} {\em terapages}, each of which must be virtually and
physically aligned to a boundary equal to its size.
A page-fault exception is raised if the physical address is insufficiently
aligned.
The algorithm for virtual-to-physical address translation is the same
as in Section~\ref{sv32algorithm}, except LEVELS equals 4 and PTESIZE
equals 8.
|