diff options
Diffstat (limited to 'tcl/board')
| -rw-r--r-- | tcl/board/arm_evaluator7t.cfg | 2 | ||||
| -rw-r--r-- | tcl/board/at91sam9g20-ek.cfg | 2 | ||||
| -rw-r--r-- | tcl/board/digilent_atlys.cfg | 2 | ||||
| -rw-r--r-- | tcl/board/hitex_lpc2929.cfg | 2 | ||||
| -rw-r--r-- | tcl/board/mini2440.cfg | 2 | ||||
| -rw-r--r-- | tcl/board/uptech_2410.cfg | 2 |
6 files changed, 6 insertions, 6 deletions
diff --git a/tcl/board/arm_evaluator7t.cfg b/tcl/board/arm_evaluator7t.cfg index 96d859c..ef4b782 100644 --- a/tcl/board/arm_evaluator7t.cfg +++ b/tcl/board/arm_evaluator7t.cfg @@ -5,5 +5,5 @@ source [find target/samsung_s3c4510.cfg] # # FIXME: # Add (A) sdram configuration -# Add (B) flash cfi programing configuration +# Add (B) flash cfi programming configuration # diff --git a/tcl/board/at91sam9g20-ek.cfg b/tcl/board/at91sam9g20-ek.cfg index 59ee4d2..e1cbb91 100644 --- a/tcl/board/at91sam9g20-ek.cfg +++ b/tcl/board/at91sam9g20-ek.cfg @@ -153,7 +153,7 @@ proc at91sam9g20_reset_init { } { nand probe nandflash_cs3 - # The AT91SAM9G20-EK evaluation board has build-in serial data flash also. + # The AT91SAM9G20-EK evaluation board has built-in serial data flash also. # Now setup SDRAM. This is tricky and configuration is very important for reliability! The current calculations # are based on 2 x Micron MT48LC16M16A2-75 memory (4 M x 16 bit x 4 banks). If you use this file as a reference diff --git a/tcl/board/digilent_atlys.cfg b/tcl/board/digilent_atlys.cfg index f298e3d..3eb6219 100644 --- a/tcl/board/digilent_atlys.cfg +++ b/tcl/board/digilent_atlys.cfg @@ -5,7 +5,7 @@ # ID 1443:0007 Digilent Development board JTAG # # However, the ixo-usb-jtag project provides an alternative open firmware for -# the on board programmer. When using thie firmware the board will then +# the on board programmer. When using this firmware the board will then # enumerate as: # ID 16c0:06ad Van Ooijen Technische Informatica # (With SerialNumber == hw_nexys) diff --git a/tcl/board/hitex_lpc2929.cfg b/tcl/board/hitex_lpc2929.cfg index 2fe1f3c..8268306 100644 --- a/tcl/board/hitex_lpc2929.cfg +++ b/tcl/board/hitex_lpc2929.cfg @@ -34,7 +34,7 @@ flash bank $_FLASHNAME cfi 0x5C000000 0x400000 2 2 $_TARGETNAME jedec_probe $_TARGETNAME configure -event reset-init { # Flash - mww 0x20200010 0x00000007 ;# FBWST: 7 wait states, not chached + mww 0x20200010 0x00000007 ;# FBWST: 7 wait states, not cached # Use PLL mww 0xFFFF8020 0x00000001 ;# XTAL_OSC_CONTROL: enable, 1-20 MHz diff --git a/tcl/board/mini2440.cfg b/tcl/board/mini2440.cfg index 9dca5a3..3d01b38 100644 --- a/tcl/board/mini2440.cfg +++ b/tcl/board/mini2440.cfg @@ -38,7 +38,7 @@ # it's apt-get install libusb-dev. When I made my config I only included # --enable-jlink and --enable-usbdevs # -# I HAVE NOT Tested this throughly, so there could still be problems. +# I HAVE NOT Tested this thoroughly, so there could still be problems. # But it should get you way ahead of the game from where I started. # If you find problems (and fixes) please post them to # openocd-development@lists.berlios.de and join the developers and diff --git a/tcl/board/uptech_2410.cfg b/tcl/board/uptech_2410.cfg index 227cf42..0a2c475 100644 --- a/tcl/board/uptech_2410.cfg +++ b/tcl/board/uptech_2410.cfg @@ -1,5 +1,5 @@ # Target Configuration for the Uptech 2410 board. -# This configuration hould also work on smdk2410, but I havn't tested it yet. +# This configuration should also work on smdk2410, but I haven't tested it yet. # Author: xionglingfeng@Gmail.com source [find target/samsung_s3c2410.cfg] |