| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Introduce support for emulating the MIPS Boston development board. The
Boston board is built around an FPGA & 3 PCIe controllers, one of which
is connected to an Intel EG20T Platform Controller Hub. It is used
during the development & debug of new CPUs and the software intended to
run on them, and is essentially the successor to the older MIPS Malta
board.
This patch does not implement the EG20T, instead connecting an already
supported ICH-9 AHCI controller. Whilst this isn't accurate it's enough
for typical stock Boston software (eg. Linux kernels) to work with hard
disks given that both the ICH-9 & EG20T implement the AHCI
specification.
Boston boards typically boot kernels in the FIT image format, and this
patch will treat kernels provided to QEMU as such. When loading a kernel
directly, the board code will generate minimal firmware much as the
Malta board code does. This firmware will set up the CM, CPC & GIC
register base addresses then set argument registers & jump to the kernel
entry point. Alternatively, bootloader code may be loaded using the bios
argument in which case no firmware will be generated & execution will
proceed from the start of the boot code at the default MIPS boot
exception vector (offset 0x1fc00000 into (c)kseg1).
Currently real Boston boards are always used with FPGA bitfiles that
include a Global Interrupt Controller (GIC), so the interrupt
configuration is only defined for such cases. Therefore the board will
only allow use of CPUs which implement the CPS components, including the
GIC, and will otherwise exit with a message.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: Yongbok Kim <yongbok.kim@imgtec.com>
[yongbok.kim@imgtec.com:
isolated boston machine support for mips64el.
updated for recent Chardev changes.
ignore missing bios/kernel for qtest.
added default -drive to if=ide explicitly.
changed default memory size into 1G due to make check failure
on 32-bit hosts]
Signed-off-by: Yongbok Kim <yongbok.kim@imgtec.com>
|
|
This reverts commit d3473e147a754e999718bf6fcb015d9978c6a1ee.
This commit creates a board which defaults to having 2GB of RAM.
Unfortunately on 32-bit hosts we can't create boards with 2GB of RAM,
and so 'make check' fails. I missed this during testing of the
merge, unfortunately. Luckily the offending commit is the last
one in the merge request, so we can just revert it for now.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
Introduce support for emulating the MIPS Boston development board. The
Boston board is built around an FPGA & 3 PCIe controllers, one of which
is connected to an Intel EG20T Platform Controller Hub. It is used
during the development & debug of new CPUs and the software intended to
run on them, and is essentially the successor to the older MIPS Malta
board.
This patch does not implement the EG20T, instead connecting an already
supported ICH-9 AHCI controller. Whilst this isn't accurate it's enough
for typical stock Boston software (eg. Linux kernels) to work with hard
disks given that both the ICH-9 & EG20T implement the AHCI
specification.
Boston boards typically boot kernels in the FIT image format, and this
patch will treat kernels provided to QEMU as such. When loading a kernel
directly, the board code will generate minimal firmware much as the
Malta board code does. This firmware will set up the CM, CPC & GIC
register base addresses then set argument registers & jump to the kernel
entry point. Alternatively, bootloader code may be loaded using the bios
argument in which case no firmware will be generated & execution will
proceed from the start of the boot code at the default MIPS boot
exception vector (offset 0x1fc00000 into (c)kseg1).
Currently real Boston boards are always used with FPGA bitfiles that
include a Global Interrupt Controller (GIC), so the interrupt
configuration is only defined for such cases. Therefore the board will
only allow use of CPUs which implement the CPS components, including the
GIC, and will otherwise exit with a message.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: Yongbok Kim <yongbok.kim@imgtec.com>
[yongbok.kim@imgtec.com:
isolated boston machine support for mips64el.
updated for recent Chardev changes.
ignore missing bios/kernel for qtest.
added default -drive to if=ide explicitly]
Signed-off-by: Yongbok Kim <yongbok.kim@imgtec.com>
|
|
We've traditionally rejected orphans here and there, but not
systematically. For instance, the sun4m machines have an onboard SCSI
HBA (bus=0), and have always rejected bus>0. Other machines with an
onboard SCSI HBA don't.
Commit a66c9dc made all orphans trigger a warning, and the previous
commit turned this into an error. The checks "here and there" are now
redundant. Drop them.
Note that the one in mips_jazz.c was wrong: it rejected bus > MAX_FD,
but MAX_FD is the number of floppy drives per bus.
Error messages change from
$ qemu-system-x86_64 -drive if=ide,bus=2
qemu-system-x86_64: Too many IDE buses defined (3 > 2)
$ qemu-system-mips64 -M magnum,accel=qtest -drive if=floppy,bus=2,id=fd1
qemu: too many floppy drives
$ qemu-system-sparc -M LX -drive if=scsi,bus=1
qemu: too many SCSI bus
to
$ qemu-system-x86_64 -drive if=ide,bus=2
qemu-system-x86_64: -drive if=ide,bus=2: machine type does not support if=ide,bus=2,unit=0
$ qemu-system-mips64 -M magnum,accel=qtest -drive if=floppy,bus=2,id=fd1
qemu-system-mips64: -drive if=floppy,bus=2,id=fd1: machine type does not support if=floppy,bus=2,unit=0
$ qemu-system-sparc -M LX -drive if=scsi,bus=1
qemu-system-sparc: -drive if=scsi,bus=1: machine type does not support if=scsi,bus=1,unit=0
Cc: John Snow <jsnow@redhat.com>
Cc: "Hervé Poussineau" <hpoussin@reactos.org>
Cc: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <1487153147-11530-9-git-send-email-armbru@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
|
|
Block backends defined with -drive if=ide are meant to be picked up by
machine initialization code: a suitable frontend gets created and
wired up automatically.
if=ide drives not picked up that way can still be used with -device as
if they had if=none, but that's unclean and best avoided. Unused ones
produce an "Orphaned drive without device" warning.
-drive parameter "if" is optional, and the default depends on the
machine type. If a machine type doesn't specify a default, the
default is "ide".
Many machine types default to if=ide, even though they don't actually
have an IDE controller. A future patch will change these defaults to
something more sensible. To prepare for it, this patch makes default
"ide" explicit for the machines that actually pick up if=ide drives:
* alpha: clipper
* arm/aarch64: spitz borzoi terrier tosa
* i386/x86_64: generic-pc-machine (with concrete subtypes pc-q35-*
pc-i440fx-* pc-* isapc xenfv)
* mips64el: fulong2e
* mips/mipsel/mips64el: malta mips
* ppc/ppc64: mac99 g3beige prep
* sh4/sh4eb: r2d
* sparc64: sun4u sun4v
Note that ppc64 machine powernv already sets an "ide" default
explicitly. Its IDE controller isn't implemented, yet.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1487153147-11530-2-git-send-email-armbru@redhat.com>
|
|
Pick a uniform chardev type name.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Some files contain multiple #includes of the same header file.
Removed most of those unnecessary duplicate entries using
scripts/clean-includes.
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Anand J <anand.indukala@gmail.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
|
|
No need to keep explicit_fe_open around if it affects only a
qemu_chr_fe_set_handlers(). Use an additional argument instead.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20161022095318.17775-24-marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
This also switches from qemu_chr_add_handlers() to
qemu_chr_fe_set_handlers(). Note that qemu_chr_fe_set_handlers() now
takes the focus when fe_open (qemu_chr_add_handlers() did take the
focus)
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20161022095318.17775-16-marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Similar to previous change, for the remaining CharDriverState front ends
users.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20161022095318.17775-13-marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
The CharDriverState.init() callback is no longer set since commit
a61ae7f88ce and thus unused. The only user, the malta FGPA display has
been converted to use an event "opened" callback instead.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20161022095318.17775-7-marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
The CharDriverState.init() callback was introduced in commit
ceecf1d158. It is only called from text_console_do_init(), but it is no
longer set since commit a61ae7f88 (init assignment has been removed by
accident).
It seems correct to use an event callback instead and print the console
text on CHR_EVENT_OPENED. That way we can remove the single user of
CharDriverState init().
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20161022095318.17775-6-marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Since commit b6607a1a204d, serial_hds_isa_init() was introduced to
factor out serial_isa_init() loops. However, sun4uv shouldn't start from
0 when there is a mm serial on 0 already. Add a "from" argument to
serial_hds_isa_init().
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20161022095318.17775-5-marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Commit 9af9e0f, 6daf194d, be62a2eb and 312fd5f got rid of a bunch, but
they keep coming back. checkpatch.pl tries to flag them since commit
5d596c2, but it's not very good at it. Offenders tracked down with
Coccinelle script scripts/coccinelle/err-bad-newline.cocci, an updated
version of the script from commit 312fd5f.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <1470224274-31522-2-git-send-email-armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
|
|
The print routine provided as part of the in-built bootloader had a bug
in that it attempted to use a jump instruction as part of a loop, but
the target has its upper bits zeroed leading to control flow
transferring to 0xb0000814 rather than the intended 0xbfc00814. Fix this
by using a branch instruction instead, which seems more fit for purpose.
A simple way to test this is to build a Linux kernel with EVA enabled &
attempt to boot it in QEMU. It will attempt to print a message
indicating the configuration mismatch but QEMU would previously
incorrectly jump & wind up printing a continuous stream of the letter E.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: Leon Alrae <leon.alrae@imgtec.com>
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
Reviewed-by: Leon Alrae <leon.alrae@imgtec.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
|
|
Delay the host-bridge 'realization' until the
PCI root bus is attached.
Signed-off-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Tested-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Acked-by: Leon Alrae <leon.alrae@imgtec.com>
Tested-by: Leon Alrae <leon.alrae@imgtec.com>
|
|
Add GIC to CPS and expose its interrupt pins instead of CPU's.
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
|
|
This changes a cpu.h dependency into a cpu-qom.h dependency.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Make ITU available in the system if CPU supports multithreading
and is part of CPS.
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
|
|
If the user specifies smp > 1 and the CPU with CM GCR support, then
create Coherent Processing System (which takes care of instantiating CPUs)
rather than CPUs directly and connect i8259 and cbus to the pins exposed by
CPS. However, there is no GIC yet, thus CPS exposes CPU's IRQ pins so use
the same pin numbers as before.
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
|
|
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
|
|
Global smp_cpus is never zero (even if user provides -smp 0), thus clocks
and irqs are always initialized for each created CPU in the loop at the
beginning of mips_malta_init.
These two lines cause a leak of already allocated timer and irqs for the
first CPU - remove them.
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
|
|
Remove CPUMIPSState from the write_bootloader() argument list as it
is not used in the function.
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
|
|
Create Cluster Power Controller and add a link to the CPC MemoryRegion
in GCR. Guest can enable / map CPC to any physical address by writing to
the memory-mapped GCR_CPC_BASE register.
Set vp-start-reset property to 1 to allow only first VP to run from reset.
Others are brought up by the guest via CPC memory-mapped registers.
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
|
|
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
|
|
Implement generic MIPS Coherent Processing System (CPS) which in this
commit just creates VPs, but it will serve as a container also for
other components like Global Configuration Registers and Cluster Power
Controller.
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
|
|
Move declarations out of qemu-common.h for functions declared in
utils/ files: e.g. include/qemu/path.h for utils/path.c.
Move inline functions out of qemu-common.h and into new files (e.g.
include/qemu/bcd.h)
Signed-off-by: Veronia Bahaa <veroniabahaa@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Commit 57cb38b included qapi/error.h into qemu/osdep.h to get the
Error typedef. Since then, we've moved to include qemu/osdep.h
everywhere. Its file comment explains: "To avoid getting into
possible circular include dependencies, this file should not include
any other QEMU headers, with the exceptions of config-host.h,
compiler.h, os-posix.h and os-win32.h, all of which are doing a
similar job to this file and are under similar constraints."
qapi/error.h doesn't do a similar job, and it doesn't adhere to
similar constraints: it includes qapi-types.h. That's in excess of
100KiB of crap most .c files don't actually need.
Add the typedef to qemu/typedefs.h, and include that instead of
qapi/error.h. Include qapi/error.h in .c files that need it and don't
get it now. Include qapi-types.h in qom/object.h for uint16List.
Update scripts/clean-includes accordingly. Update it further to match
reality: replace config.h by config-target.h, add sysemu/os-posix.h,
sysemu/os-win32.h. Update the list of includes in the qemu/osdep.h
comment quoted above similarly.
This reduces the number of objects depending on qapi/error.h from "all
of them" to less than a third. Unfortunately, the number depending on
qapi-types.h shrinks only a little. More work is needed for that one.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
[Fix compilation without the spice devel packages. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Change all machine_init() users that simply call type_register*()
to use type_init().
Cc: Evgeny Voevodin <e.voevodin@samsung.com>
Cc: Maksim Kozlov <m.kozlov@samsung.com>
Cc: Igor Mitsyanko <i.mitsyanko@gmail.com>
Cc: Dmitry Solodkiy <d.solodkiy@samsung.com>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Rob Herring <robh@kernel.org>
Cc: Andrzej Zaborowski <balrogg@gmail.com>
Cc: Michael Walle <michael@walle.cc>
Cc: "Hervé Poussineau" <hpoussin@reactos.org>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: Leon Alrae <leon.alrae@imgtec.com>
Cc: Alexander Graf <agraf@suse.de>
Cc: David Gibson <david@gibson.dropbear.id.au>
Cc: Blue Swirl <blauwirbel@gmail.com>
Cc: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Acked-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
|
|
Some CPUs are of an opposite data-endianness to other components in the
system. Sometimes elfs have the data sections layed out with this CPU
data-endianness accounting for when loaded via the CPU, so byte swaps
(relative to other system components) will occur.
The leading example, is ARM's BE32 mode, which is is basically LE with
address manipulation on half-word and byte accesses to access the
hw/byte reversed address. This means that word data is invariant
across LE and BE32. This also means that instructions are still LE.
The expectation is that the elf will be loaded via the CPU in this
endianness scheme, which means the data in the elf is reversed at
compile time.
As QEMU loads via the system memory directly, rather than the CPU, we
need a mechanism to reverse elf data endianness to implement this
possibility.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
Floppy uses the DMA controller in rc4030 chipset, and not the i8259 from the ISA bus.
It's better to disable DMA than to call the wrong DMA controller.
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Message-id: 1453843944-26833-13-git-send-email-hpoussin@reactos.org
Signed-off-by: John Snow <jsnow@redhat.com>
|
|
i8257 DMA controller exists on one ISA bus, so let's specify it at initialization.
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Message-id: 1453843944-26833-3-git-send-email-hpoussin@reactos.org
Signed-off-by: John Snow <jsnow@redhat.com>
|
|
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Leon Alrae <leon.alrae@imgtec.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
|
|
We can have at most one ISA bus. If you try to create another one,
isa_bus_new() complains to stderr and returns null.
isa_bus_new() is called in two contexts, machine's init() and device's
realize() methods. Since complaining to stderr is not proper in the
latter context, convert isa_bus_new() to Error.
Machine's init():
* mips_jazz_init(), called from the init() methods of machines
"magnum" and "pica"
* mips_r4k_init(), the init() method of machine "mips"
* pc_init1() called from the init() methods of non-q35 PC machines
* typhoon_init(), called from clipper_init(), the init() method of
machine "clipper"
These callers always create the first ISA bus, hence isa_bus_new()
can't fail. Simply pass &error_abort.
Device's realize():
* i82378_realize(), of PCI device "i82378"
* ich9_lpc_realize(), of PCI device "ICH9-LPC"
* pci_ebus_realize(), of PCI device "ebus"
* piix3_realize(), of PCI device "pci-piix3", abstract parent of
"PIIX3" and "PIIX3-xen"
* piix4_realize(), of PCI device "PIIX4"
* vt82c686b_realize(), of PCI device "VT82C686B"
Propagate the error. Note that these devices are typically created
only by machine init() methods with qdev_init_nofail() or similar. If
we screwed up and created an ISA bus before that call, we now give up
right away. Before, we'd hobble on, and typically die in
isa_bus_irqs(). Similar if someone finds a way to hot-plug one of
these critters.
Cc: Richard Henderson <rth@twiddle.net>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: "Hervé Poussineau" <hpoussin@reactos.org>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Markus Armbruster <armbru@pond.sub.org>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Hervé Poussineau <hpoussin@reactos.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-Id: <1450370121-5768-11-git-send-email-armbru@redhat.com>
|
|
Signed-off-by: Cao jin <caoj.fnst@cn.fujitsu.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
|
|
The GT64xxx's internal registers can be placed above the first 4 GiB
in the address space, but not above the first 64 GiB. Correctly cast
the register to a 64-bit integer, and mask away bits above bit 35.
Datasheet at http://pdf.datasheetarchive.com/datasheetsmain/Datasheets-33/DSA-655889.pdf
(bug reported by Coverity).
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
|
|
Commit 71c199c81d29 ("mips_malta: provide ememsize env variable to
kernels") changed the meaning of loaderparams.ram_size to be the whole
of RAM rather than just the low part below where the boot code is placed
for KVM, but it didn't update the PC initialisation for KVM to use
ram_low_size. Fix that now.
Fixes: 71c199c81d29 ("mips_malta: provide ememsize env variable to kernels")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Leon Alrae <leon.alrae@imgtec.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
Reviewed-by: Leon Alrae <leon.alrae@imgtec.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
|
|
* First batch of MAINTAINERS updates
* IOAPIC fixes (to pass kvm-unit-tests with -machine kernel_irqchip=off)
* NBD API upgrades from Daniel
* strtosz fixes from Marc-André
* improved support for readonly=on on scsi-generic devices
* new "info ioapic" and "info lapic" monitor commands
* Peter Crosthwaite's ELF_MACHINE cleanups
* docs patches from Thomas and Daniel
# gpg: Signature made Fri 25 Sep 2015 11:20:52 BST using RSA key ID 78C7AE83
# gpg: Good signature from "Paolo Bonzini <bonzini@gnu.org>"
# gpg: aka "Paolo Bonzini <pbonzini@redhat.com>"
* remotes/bonzini/tags/for-upstream: (52 commits)
doc: Refresh URLs in the qemu-tech documentation
docs: describe the QEMU build system structure / design
typedef: add typedef for QemuOpts
i386: interrupt poll processing
i386: partial revert of interrupt poll fix
ppc: Rename ELF_MACHINE to be PPC specific
i386: Rename ELF_MACHINE to be x86 specific
alpha: Remove ELF_MACHINE from cpu.h
mips: Remove ELF_MACHINE from cpu.h
sparc: Remove ELF_MACHINE from cpu.h
s390: Remove ELF_MACHINE from cpu.h
sh4: Remove ELF_MACHINE from cpu.h
xtensa: Remove ELF_MACHINE from cpu.h
tricore: Remove ELF_MACHINE from cpu.h
or32: Remove ELF_MACHINE from cpu.h
lm32: Remove ELF_MACHINE from cpu.h
unicore: Remove ELF_MACHINE from cpu.h
moxie: Remove ELF_MACHINE from cpu.h
cris: Remove ELF_MACHINE from cpu.h
m68k: Remove ELF_MACHINE from cpu.h
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
Originally, timers were ticks based, and it made sense to
add ticks to current time to know when to trigger an alarm.
But since commit:
7447545 change all other clock references to use nanosecond resolution accessors
All timers use nanoseconds and we need to convert ticks to nanoseconds, by
doing something like:
y = muldiv64(x, get_ticks_per_sec(), TIMER_FREQ)
where x is the number of device ticks and y the number of system ticks.
y is used as nanoseconds in timer functions,
it works because 1 tick is 1 nanosecond.
(get_ticks_per_sec() is 10^9)
But as MIPS timer frequency is 100 MHz, we can also do:
y = x * 10; /* 100 MHz period is 10 ns */
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Reviewed-by: Leon Alrae <leon.alrae@imgtec.com>
|
|
The only generic code relying on this is linux-user, but linux users'
default behaviour of defaulting ELF_MACHINE to ELF_ARCH will handle
this.
The bootloaders can just pass EM_MIPS directly, as that is
architecture specific code.
This removes another architecture specific definition from the global
namespace.
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: Leon Alrae <leon.alrae@imgtec.com>
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Acked-By: Riku Voipio <riku.voipio@linaro.org>
Signed-off-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
The script used for converting from QEMUMachine had used one
DEFINE_MACHINE() per machine registered. In cases where multiple
machines are registered from one source file, avoid the excessive
generation of module init functions by reverting this unrolling.
Signed-off-by: Andreas Färber <afaerber@suse.de>
|
|
Convert all machines to use DEFINE_MACHINE() instead of QEMUMachine
automatically using a script.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
[AF: Style cleanups, convert imx25_pdk machine]
Signed-off-by: Andreas Färber <afaerber@suse.de>
|
|
into staging
Error reporting patches
# gpg: Signature made Fri 18 Sep 2015 13:42:49 BST using RSA key ID EB918653
# gpg: Good signature from "Markus Armbruster <armbru@redhat.com>"
# gpg: aka "Markus Armbruster <armbru@pond.sub.org>"
* remotes/armbru/tags/pull-error-2015-09-18:
memory: Fix bad error handling in memory_region_init_ram_ptr()
loader: Fix memory_region_init_resizeable_ram() error handling
Fix bad error handling after memory_region_init_ram()
error: New error_fatal
MAINTAINERS: Add "Error reporting" entry
error: Copy location information in error_copy()
hmp: Allow for error message hints on HMP
error: only prepend timestamp on stderr
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
Symptom:
$ qemu-system-x86_64 -m 10000000
Unexpected error in ram_block_add() at /work/armbru/qemu/exec.c:1456:
upstream-qemu: cannot set up guest memory 'pc.ram': Cannot allocate memory
Aborted (core dumped)
Root cause: commit ef701d7 screwed up handling of out-of-memory
conditions. Before the commit, we report the error and exit(1), in
one place, ram_block_add(). The commit lifts the error handling up
the call chain some, to three places. Fine. Except it uses
&error_abort in these places, changing the behavior from exit(1) to
abort(), and thus undoing the work of commit 3922825 "exec: Don't
abort when we can't allocate guest memory".
The three places are:
* memory_region_init_ram()
Commit 4994653 (right after commit ef701d7) lifted the error
handling further, through memory_region_init_ram(), multiplying the
incorrect use of &error_abort. Later on, imitation of existing
(bad) code may have created more.
* memory_region_init_ram_ptr()
The &error_abort is still there.
* memory_region_init_rom_device()
Doesn't need fixing, because commit 33e0eb5 (soon after commit
ef701d7) lifted the error handling further, and in the process
changed it from &error_abort to passing it up the call chain.
Correct, because the callers are realize() methods.
Fix the error handling after memory_region_init_ram() with a
Coccinelle semantic patch:
@r@
expression mr, owner, name, size, err;
position p;
@@
memory_region_init_ram(mr, owner, name, size,
(
- &error_abort
+ &error_fatal
|
err@p
)
);
@script:python@
p << r.p;
@@
print "%s:%s:%s" % (p[0].file, p[0].line, p[0].column)
When the last argument is &error_abort, it gets replaced by
&error_fatal. This is the fix.
If the last argument is anything else, its position is reported. This
lets us check the fix is complete. Four positions get reported:
* ram_backend_memory_alloc()
Error is passed up the call chain, ultimately through
user_creatable_complete(). As far as I can tell, it's callers all
handle the error sanely.
* fsl_imx25_realize(), fsl_imx31_realize(), dp8393x_realize()
DeviceClass.realize() methods, errors handled sanely further up the
call chain.
We're good. Test case again behaves:
$ qemu-system-x86_64 -m 10000000
qemu-system-x86_64: cannot set up guest memory 'pc.ram': Cannot allocate memory
[Exit 1 ]
The next commits will repair the rest of commit ef701d7's damage.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <1441983105-26376-3-git-send-email-armbru@redhat.com>
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
|
|
cpu_mips_get_random() function is used to generate a random index from
CP0.Wired to TLBSize-1 range. Current implementation avoids generating
the same as before value, hence the while loop. If the guest sets
CP0.Wired to TLBSize-1 (which actually does not sound to be very
practical) QEMU will get stuck in the loop infinitely as we always
generate the same index.
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
|
|
The LFSR algorithm, used for generating random TLB indexes for TLBWR
instruction, was inclined to produce a degenerate sequence in some cases.
For example, for 16-entry TLB size and Wired=1, it gives: 15, 6, 7, 2,
7, 2, 7, 2, 7, 2, 7, 2, 7, 2, 7, 2, 7, 2, 7, 2, 7, 2, 7, 2, 7, 2, 7, 2...
When replaced with LCG algorithm from ISO/IEC 9899 standard, the sequence
looks much better, with about the same computational effort needed.
Signed-off-by: Serge Vakulenko <serge.vakulenko@gmail.com>
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
Reviewed-by: Leon Alrae <leon.alrae@imgtec.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
|
|
* Support for jemalloc
* qemu_mutex_lock_iothread "No such process" fix
* cutils: qemu_strto* wrappers
* iohandler.c simplification
* Many other fixes and misc patches.
And some MTTCG work (with Emilio's fixes squashed):
* Signal-free TCG kick
* Removing spinlock in favor of QemuMutex
* User-mode emulation multi-threading fixes/docs
# gpg: Signature made Thu 10 Sep 2015 09:03:07 BST using RSA key ID 78C7AE83
# gpg: Good signature from "Paolo Bonzini <bonzini@gnu.org>"
# gpg: aka "Paolo Bonzini <pbonzini@redhat.com>"
* remotes/bonzini/tags/for-upstream: (44 commits)
cutils: work around platform differences in strto{l,ul,ll,ull}
cpu-exec: fix lock hierarchy for user-mode emulation
exec: make mmap_lock/mmap_unlock globally available
tcg: comment on which functions have to be called with mmap_lock held
tcg: add memory barriers in page_find_alloc accesses
remove unused spinlock.
replace spinlock by QemuMutex.
cpus: remove tcg_halt_cond and tcg_cpu_thread globals
cpus: protect work list with work_mutex
scripts/dump-guest-memory.py: fix after RAMBlock change
configure: Add support for jemalloc
add macro file for coccinelle
configure: factor out adding disas configure
vhost-scsi: fix wrong vhost-scsi firmware path
checkpatch: remove tests that are not relevant outside the kernel
checkpatch: adapt some tests to QEMU
CODING_STYLE: update mixed declaration rules
qmp: Add example usage of strto*l() qemu wrapper
cutils: Add qemu_strtoull() wrapper
cutils: Add qemu_strtoll() wrapper
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
The free() and g_free() functions both happily accept
NULL on any platform QEMU builds on. As such putting a
conditional 'if (foo)' check before calls to 'free(foo)'
merely serves to bloat the lines of code.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
|
|
This is unused. cpu_exit now is almost exclusively an internal function
to the CPU execution loop. In a few patches, we'll change the remaining
occurrences to qemu_cpu_kick, making it truly internal.
Reviewed-by: Richard henderson <rth@twiddle.net>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
