vl: replace deprecated qbus_reset_all registration

Replace deprecated qbus_reset_all by resettable_cold_reset_fn for
the sysbus reset registration.

Apart for the raspi machines, this does not impact the behavior
because:
+ at this point resettable just calls the old reset methods of devices
  and buses in the same order as qdev/qbus.
+ resettable handlers registered with qemu_register_reset are
  serialized; there is no interleaving.
+ eventual explicit calls to legacy reset API (device_reset or
  qdev/qbus_reset) inside this reset handler will not be masked out
  by resettable mechanism; they do not go through resettable api.

For the raspi machines, during the sysbus reset the sd-card is not
reset twice anymore but only once. This is a consequence of switching
both sysbus reset and changing parent to resettable; it detects the
second reset is not needed. This has no impact on the state after
reset; the sd-card reset method only reset local state and query
information from the block backend.

The raspi reset change can be observed by using the following command
(reset will occurs, then do Ctrl-C to end qemu; no firmware is
given here).
qemu-system-aarch64 -M raspi3 \
    -trace resettable_phase_hold_exec \
    -trace qdev_update_parent_bus \
    -trace resettable_change_parent \
    -trace qdev_reset -trace qbus_reset

Before the patch, the qdev/qbus_reset traces show when reset method are
called. After the patch, the resettable_phase_hold_exec show when reset
method are called.

The traced reset order of the raspi3 is listed below. I've added empty
lines and the tree structure.

 +->bcm2835-peripherals reset
 |
 |       +->sd-card reset
 |   +->sd-bus reset
 +->bcm2835_gpio reset
 |      -> dev_update_parent_bus (move the sd-card on the sdhci-bus)
 |      -> resettable_change_parent
 |
 +->bcm2835-dma reset
 |
 |   +->bcm2835-sdhost-bus reset
 +->bcm2835-sdhost reset
 |
 |       +->sd-card (reset ONLY BEFORE BEFORE THE PATCH)
 |   +->sdhci-bus reset
 +->generic-sdhci reset
 |
 +->bcm2835-rng reset
 +->bcm2835-property reset
 +->bcm2835-fb reset
 +->bcm2835-mbox reset
 +->bcm2835-aux reset
 +->pl011 reset
 +->bcm2835-ic reset
 +->bcm2836-control reset
System reset

In both case, the sd-card is reset (being on bcm2835_gpio/sd-bus) then moved
to generic-sdhci/sdhci-bus by the bcm2835_gpio reset method.

Before the patch, it is then reset again being part of generic-sdhci/sdhci-bus.
After the patch, it considered again for reset but its reset method is not
called because it is already flagged as reset.

Signed-off-by: Damien Hedde <damien.hedde@greensocs.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20200123132823.1117486-11-damien.hedde@greensocs.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>

1 files changed, 9 insertions, 1 deletions

diff --git a/vl.c b/vl.c
index b0f52c4..24951b5 100644
--- a/vl.c
+++ b/vl.c
@@ -4381,7 +4381,15 @@ int main(int argc, char **argv, char **envp)
 
     /* TODO: once all bus devices are qdevified, this should be done
      * when bus is created by qdev.c */
-    qemu_register_reset(qbus_reset_all_fn, sysbus_get_default());
+    /*
+     * TODO: If we had a main 'reset container' that the whole system
+     * lived in, we could reset that using the multi-phase reset
+     * APIs. For the moment, we just reset the sysbus, which will cause
+     * all devices hanging off it (and all their child buses, recursively)
+     * to be reset. Note that this will *not* reset any Device objects
+     * which are not attached to some part of the qbus tree!
+     */
+    qemu_register_reset(resettable_cold_reset_fn, sysbus_get_default());
     qemu_run_machine_init_done_notifiers();
 
     if (rom_check_and_register_reset() != 0) {