1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
|
# Copyright 2010-2016 Free Software Foundation, Inc.
# This program is free software; you can redistribute it and/or modify
# it under the terms of the GNU General Public License as published by
# the Free Software Foundation; either version 3 of the License, or
# (at your option) any later version.
#
# This program is distributed in the hope that it will be useful,
# but WITHOUT ANY WARRANTY; without even the implied warranty of
# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
# GNU General Public License for more details.
#
# You should have received a copy of the GNU General Public License
# along with this program. If not, see <http://www.gnu.org/licenses/>. */
# In some cases gdbserver cannot find the DT_DEBUG library list on its own and
# it needs to fall back to GDB solib-svr4.c look up via symbols from the main
# executable.
# gdbserver :1234 ld-linux-x86-64.so.2 /bin/prog
# gdb /bin/prog
# (gdb) target remote ...
load_lib gdbserver-support.exp
load_lib prelink-support.exp
if {[skip_gdbserver_tests] || [skip_shlib_tests]} {
return
}
# This test case (currently) does not support remote targets, since it
# assumes the ELF interpreter can be found on the host system
if [is_remote target] then {
return
}
standard_testfile solib-list-main.c
set srclibfile ${testfile}-lib.c
set binlibfile [standard_output_file ${testfile}.so]
set executable ${testfile}
set objfile ${binfile}.o
if { [get_compiler_info]
|| [gdb_compile_shlib "${srcdir}/${subdir}/${srclibfile}" "${binlibfile}" [list debug ldflags=-Wl,-soname,${binlibfile}]] != ""
|| [gdb_compile "${srcdir}/${subdir}/${srcfile}" "${objfile}" object {debug}] != ""
|| [gdb_compile "${objfile} ${binlibfile}" "${binfile}" executable {}] != "" } {
untested "could not compile sources"
return -1
}
set interp_system [section_get ${binfile} .interp]
verbose -log "system interpreter is: $interp_system"
foreach nonstop { 0 1 } { with_test_prefix "non-stop $nonstop" {
# clean_restart assumes ${objdir}/${subdir}/ which is not applicable
# for ${interp_system}.
gdb_exit
gdb_start
gdb_reinitialize_dir $srcdir/$subdir
gdb_load ${interp_system}
gdb_load_shlibs ${binfile}
gdb_load_shlibs ${binlibfile}
# Make sure we're disconnected, in case we're testing with an
# extended-remote board, therefore already connected.
gdb_test "disconnect" ".*"
gdb_test "set non-stop $nonstop"
# It is required for the non-stop mode, GDB would try to step over
# _dl_debug_state breakpoint will still only ld.so loaded in gdbserver.
# But GDB having symbols from the main executable it would try to use
# displaced-stepping buffer at unmapped that time address _start.
gdb_test "set displaced-stepping off"
set res [gdbserver_spawn ${binfile}]
set gdbserver_protocol [lindex $res 0]
set gdbserver_gdbport [lindex $res 1]
# Load BINFILE after gdbserver_spawn (so that gdbserver executes ld.so)
# but before "target remote" below so that qSymbol data get already
# initialized from BINFILE (and not from ld.so first needing a change to
# BINFILE later).
gdb_test "file ${binfile}" {Reading symbols from .*\.\.\.done\..*} "file binfile" \
{(Are you sure you want to change the file|Load new symbol table from ".*")\? \(y or n\) } "y"
set test "target $gdbserver_protocol"
gdb_test_multiple "target $gdbserver_protocol $gdbserver_gdbport" $test {
-re "Remote debugging using .*\r\n$gdb_prompt " {
# Do not anchor end, there may be more output in non-stop mode.
pass $test
}
}
gdb_test "continue" "Program received signal SIGUSR1, .*"
gdb_test "sharedlibrary" ".*"
gdb_test "p libvar" " = 23"
}}
|
