aboutsummaryrefslogtreecommitdiff
path: root/opcodes
AgeCommit message (Collapse)AuthorFilesLines
2016-11-09X86: Remove the .s suffix from EVEX vpextrwH.J. Lu5-12/+18
The .s suffix indicates that the instruction is encoded by swapping 2 register operands. Since vpextrw takes an XMM register and an integer register, the .s suffix should be ignored for EVEX vpextrw. gas/ PR binutils/20799 * testsuite/gas/i386/opcode.s: Add a test for EVEX vpextrw. * testsuite/gas/i386/opcode-intel.d: Updated. * testsuite/gas/i386/opcode-suffix.d: Likewise. * testsuite/gas/i386/opcode.d: Likewise. * testsuite/gas/i386/x86-64-avx512bw-opts.s: Remove vpextrw tests. * testsuite/gas/i386/x86-64-avx512bw-opts-intel.d: Updated. * testsuite/gas/i386/x86-64-avx512bw-opts.d: Likewise. opcodes/ PR binutils/20799 * i386-dis-evex.h (evex_table): Replace EdqwS with Edqw. * i386-dis.c (EdqwS): Removed. (dqw_swap_mode): Likewise. (intel_operand_size): Don't check dqw_swap_mode. (OP_E_register): Likewise. (OP_E_memory): Likewise. (OP_G): Likewise. (OP_EX): Likewise. * i386-opc.tbl: Remove "S" from EVEX vpextrw. * i386-tbl.h: Regerated.
2016-11-09Update opcodes/ChangeLogH.J. Lu1-0/+1
2016-11-09X86: Merge AVX512F vmovqH.J. Lu3-81/+17
AVX512F vmovq doesn't support masking. We can't swap register operand in AVX512F vmovq with Reg64 since Reg64 != RegXMM. This patch merges AVX512F vmovq. * i386-opc.tbl: Merge AVX512F vmovq.
2016-11-08X86: Remove the THREE_BYTE_0F7A entryH.J. Lu2-295/+9
Remove the THREE_BYTE_0F7A entry which is leftover from SSE5. PR binutils/20701 * i386-dis.c (THREE_BYTE_0F7A): Removed. (dis386_twobyte): Don't use THREE_BYTE_0F7A. (three_byte_table): Remove THREE_BYTE_0F7A.
2016-11-07X86: Properly handle bad FPU opcodeH.J. Lu2-18/+37
Since Bad_Opcode and FGRPd9_2 were the same in i386-dis.c, all Bad_Opcode entries in float_reg were displaced as FGRPd9_2. This patch adds an entry for Bad_Opcode in fgrps to avoid treating it as FGRPd9_2. gas/ PR binutils/20775 * testsuite/gas/i386/i386.exp: Run fpu-bad. * testsuite/gas/i386/fpu-bad.d: New file. * testsuite/gas/i386/fpu-bad.s: Likewise. opcodes/ PR binutils/20775 * i386-dis.c (FGRPd9_2): Replace 0 with 1. (FGRPd9_4): Replace 1 with 2. (FGRPd9_5): Replace 2 with 3. (FGRPd9_6): Replace 3 with 4. (FGRPd9_7): Replace 4 with 5. (FGRPda_5): Replace 5 with 6. (FGRPdb_4): Replace 6 with 7. (FGRPde_3): Replace 7 with 8. (FGRPdf_4): Replace 8 with 9. (fgrps): Add an entry for Bad_Opcode.
2016-11-04arc/nps400: Validate address type operands correctlyAndrew Burgess3-2/+26
When we match against an address type operand within an instruction it is important that we match exactly the right address type operand early on, during the opcode selection phase. If we wait until the operand insertion phase to check that we have the correct address operand, then it is too late to select an alternative opcode. This becomes important only when we have multiple opcodes with the same mnemonic, and operand lists that differ only in the type of the address operands. This commit fixes this issue, and adds some example instructions that require this issue to be fixed (the instructions are identical except for the address type operand). gas/ChangeLog: * config/tc-arc.c (find_opcode_match): Use insert function to validate matching address type operands. * testsuite/gas/arc/nps400-10.d: New file. * testsuite/gas/arc/nps400-10.s: New file. opcodes/ChangeLog: * arc-opc.c (arc_flag_operands): Add F_DI14. (arc_flag_classes): Add C_DI14. * arc-nps400-tbl.h: Add new exc instructions.
2016-11-03arc: Implement NPS-400 dcmac instructionGraham Markall4-1/+99
gas/ChangeLog: * testsuite/gas/arc/nps-400-9.d: Added. * testsuite/gas/arc/nps-400-9.s: Added. include/ChangeLog: * opcode/arc.h: Add PROTOCOL_DECODE to insn_class_t. opcodes/ChangeLog: * arc-dis.c (arc_insn_length): Return length 8 for instructions with major opcode 0xa. * arc-nps-400-tbl.h: Add dcmac instruction. * arc-opc.c (arc_operands): Added operands for dcmac instruction. (insert_nps_rbdouble_64): Added. (extract_nps_rbdouble_64): Added. (insert_nps_proto_size): Added. (extract_nps_proto_size): Added.
2016-11-03arc: Change max instruction length to 64-bitsAndrew Burgess7-963/+745
The current handling for arc instructions longer than 32-bits is all handled as a special case in both the assembler and disassembler. The problem with this approach is that it leads to code duplication, selecting a long instruction is exactly the same process as selecting a short instruction, except over more bits, in both cases we select based on bit comparison, and initial operand insertion and extraction. This commit unifies both the long and short instruction worlds, converting the core opcodes library from being largely 32-bit focused, to being largely 64-bit focused. The changes are, on the whole, not too much. There's obviously a lot of type changes but otherwise the bulk of the code just works. Most of the actual functional changes are to code that previously handled the longer 48 or 64 bit instructions. The insert/extract handlers for these have now been brought into line with the short instruction insert/extract handlers. All of the special case handling code that was previously added has now been removed again. Overall, this commit reduces the amount of code in the arc assembler and disassembler. gas/ChangeLog: * config/tc-arc.c (struct arc_insn): Change type of insn field. (md_number_to_chars_midend): Support 6- and 8-byte values. (emit_insn0): Update debug output. (find_opcode_match): Likewise. (build_fake_opcode_hash_entry): Delete. (find_special_case_long_opcode): Delete. (find_special_case): Remove long format special case handling. (insert_operand): Change instruction type and update debug print format. (assemble_insn): Change instruction type, update debug print formats, and remove unneeded assert. include/ChangeLog: * opcode/arc.h (struct arc_opcode): Change type of opcode and mask fields. (struct arc_long_opcode): Delete. (struct arc_operand): Change types for insert and extract handlers. opcodes/ChangeLog: * arc-dis.c (struct arc_operand_iterator): Remove all fields relating to long instruction processing, add new limm field. (OPCODE): Rename to... (OPCODE_32BIT_INSN): ...this. (OPCODE_AC): Delete. (skip_this_opcode): Handle different instruction lengths, update macro name. (special_flag_p): Update parameter type. (find_format_from_table): Update for more instruction lengths. (find_format_long_instructions): Delete. (find_format): Update for more instruction lengths. (arc_insn_length): Likewise. (extract_operand_value): Update for more instruction lengths. (operand_iterator_next): Remove code relating to long instructions. (arc_opcode_to_insn_type): New function. (print_insn_arc):Update for more instructions lengths. * arc-ext.c (extInstruction_t): Change argument type. * arc-ext.h (extInstruction_t): Change argument type. * arc-fxi.h: Change type unsigned to unsigned long long extensively throughout. * arc-nps400-tbl.h: Add long instructions taken from arc_long_opcodes table in arc-opc.c. * arc-opc.c: Update parameter types on insert/extract handlers. (arc_long_opcodes): Delete. (arc_num_long_opcodes): Delete. (arc_opcode_len): Update for more instruction lengths.
2016-11-03arc: Swap highbyte and lowbyte in print_insn_arcGraham Markall2-4/+8
highbyte and lowbyte actually refer to the low byte and the high byte respectively, but are used consistently in this swapped order. This commit swaps them round so that highbyte refers to the high byte and lowbyte refers to the low byte. There should be no functional change after this commit. opcodes/ChangeLog: * arc-dis.c (print_insn_arc): Swap highbyte and lowbyte.
2016-11-03arc: Replace ARC_SHORT macro with arc_opcode_len functionGraham Markall3-4/+21
In preparation for moving to a world where arc instructions can be 2, 4, 6, or 8 bytes in length, replace the ARC_SHORT macro (which is either true of false) with an arc_opcode_len function that returns a length in bytes. There should be no functional change after this commit. gas/ChangeLog: * config/tc-arc.c (assemble_insn): Replace use of ARC_SHORT with arc_opcode_len. include/ChangeLog: * opcode/arc.h (arc_opcode_len): Declare. (ARC_SHORT): Delete. opcodes/ChangeLog: * arc-dis.c (find_format_from_table): Replace use of ARC_SHORT with arc_opcode_len. (find_format_long_instructions): Likewise. * arc-opc.c (arc_opcode_len): New function.
2016-11-03arc/opcodes/nps400: Fix some instruction masksAndrew Burgess2-3/+7
A few masks were incorrect, there were opcode bits that lives outside of the instruction mask, the effected instructions are decode1, zncv, and efabgt. Previously these instructions would assemble and disassemble correctly, and a correctly encoded binary should behave no differently. The only difference would be seen in a few incorrectly encoded binaries, previously these would have decoded to the above instructions, while now they will not. opcodes/ChangeLog: * arc-nps400-tbl.h: Fix some instruction masks.
2016-11-03X86: Reuse opcode 0x80 decoder for opcode 0x82H.J. Lu2-58/+24
Since opcode 0x82 is an alias of opcode 0x80, we can reuse opcode 0x80 decoder. * i386-dis.c (REG_82): Removed. (X86_64_82_REG_0): Likewise. (X86_64_82_REG_1): Likewise. (X86_64_82_REG_2): Likewise. (X86_64_82_REG_3): Likewise. (X86_64_82_REG_4): Likewise. (X86_64_82_REG_5): Likewise. (X86_64_82_REG_6): Likewise. (X86_64_82_REG_7): Likewise. (X86_64_82): New. (dis386): Use X86_64_82 instead of REG_82. (reg_table): Remove REG_82. (x86_64_table): Add X86_64_82. Remove X86_64_82_REG_0, X86_64_82_REG_1, X86_64_82_REG_2, X86_64_82_REG_3, X86_64_82_REG_4, X86_64_82_REG_5, X86_64_82_REG_6 and X86_64_82_REG_7.
2016-11-03X86: Decode opcode 0x82 as opcode 0x80 in 32-bit modeH.J. Lu2-1/+79
Update x86 disassembler to treat opcode 0x82 as an aliase of opcode 0x80 in 32-bit mode. gas/ PR binutils/20754 * testsuite/gas/i386/opcode.s: Add tests for opcode 0x82. * testsuite/gas/i386/opcode-intel.d: Updated. * testsuite/gas/i386/opcode.d: Likewise. opcodes/ PR binutils/20754 * i386-dis.c (REG_82): New. (X86_64_82_REG_0): Likewise. (X86_64_82_REG_1): Likewise. (X86_64_82_REG_2): Likewise. (X86_64_82_REG_3): Likewise. (X86_64_82_REG_4): Likewise. (X86_64_82_REG_5): Likewise. (X86_64_82_REG_6): Likewise. (X86_64_82_REG_7): Likewise. (dis386): Use REG_82. (reg_table): Add REG_82. (x86_64_table): Add X86_64_82_REG_0, X86_64_82_REG_1, X86_64_82_REG_2, X86_64_82_REG_3, X86_64_82_REG_4, X86_64_82_REG_5, X86_64_82_REG_6 and X86_64_82_REG_7.
2016-11-03X86: Rename REG_82 to REG_83H.J. Lu2-3/+10
The REG_82 entry in x86 disassembler is for opcode 0x83, not opcode 0x82. * i386-dis.c (REG_82): Renamed to ... (REG_83): This. (dis386): Updated. (reg_table): Likewise.
2016-11-02Enable Intel AVX512_4VNNIW instructionsIgor Tsimbalist8-5340/+5517
gas/ * config/tc-i386.c: (cpu_arch) Add .avx512_4vnniw. (cpu_noarch): Add noavx512_4vnniw. * doc/c-i386.texi: Document avx512_4vnniw, noavx512_4vnniw. * testsuite/gas/i386/i386.exp: Run AVX512_4VNNIW tests. * testsuite/gas/i386/avx512_4vnniwd_vl-intel.d: New test. * testsuite/gas/i386/avx512_4vnniwd_vl.d: Ditto. * testsuite/gas/i386/avx512_4vnniwd_vl.s: Ditto. * testsuite/gas/i386/avx512_4vnniwd-intel.d: Ditto. * testsuite/gas/i386/avx512_4vnniwd.d: Ditto. * testsuite/gas/i386/avx512_4vnniwd.s: Ditto. * testsuite/gas/i386/x86-64-avx512_4vnniwd_vl-intel.d: Ditto. * testsuite/gas/i386/x86-64-avx512_4vnniwd_vl.d: Ditto. * testsuite/gas/i386/x86-64-avx512_4vnniwd_vl.s: Ditto. * testsuite/gas/i386/x86-64-avx512_4vnniwd-intel.d: Ditto. * testsuite/gas/i386/x86-64-avx512_4vnniwd.d: Ditto. * testsuite/gas/i386/x86-64-avx512_4vnniwd.s: Ditto. opcodes/ * i386-dis.c (enum): Add PREFIX_EVEX_0F3852, PREFIX_EVEX_0F3853. * i386-dis-evex.h (evex_table): Updated. * i386-gen.c (cpu_flag_init): Add CPU_AVX512_4VNNIW_FLAGS, CPU_ANY_AVX512_4VNNIW_FLAGS. Update CPU_ANY_AVX512F_FLAGS. (cpu_flags): Add CpuAVX512_4VNNIW. * i386-opc.h (enum): (AVX512_4VNNIW): New. (i386_cpu_flags): Add cpuavx512_4vnniw. * i386-opc.tbl: Add Intel AVX512_4VNNIW instructions. * i386-init.h: Regenerate. * i386-tbl.h: Ditto.
2016-11-02Enable Intel AVX512_4FMAPS instructionsIgor Tsimbalist7-10561/+10779
gas/ * config/tc-i386.c (cpu_arch): Add .avx512_4fmaps. (cpu_noarch): Add noavx512_4fmaps. (process_operands): Handle implicit quad group. * doc/c-i386.texi: Document avx512_4fmaps, noavx512_4fmaps. * testsuite/gas/i386/i386.exp: Add AVX512_4FMAPS tests. * testsuite/gas/i386/avx512_4fmaps_vl-intel.d: New test. * testsuite/gas/i386/avx512_4fmaps_vl.d: Ditto. * testsuite/gas/i386/avx512_4fmaps_vl.s: Ditto. * testsuite/gas/i386/avx512_4fmaps-intel.d: Ditto. * testsuite/gas/i386/avx512_4fmaps.d: Ditto. * testsuite/gas/i386/avx512_4fmaps.s: Ditto. * testsuite/gas/i386/avx512_4fmaps-warn.l: Ditto. * testsuite/gas/i386/avx512_4fmaps-warn.s: Ditto. * testsuite/gas/i386/avx512_4fmaps_vl-warn.l: Ditto. * testsuite/gas/i386/avx512_4fmaps_vl-warn.s: Ditto. * testsuite/gas/i386/x86-64-avx512_4fmaps_vl-intel.d: Ditto. * testsuite/gas/i386/x86-64-avx512_4fmaps_vl.d: Ditto. * testsuite/gas/i386/x86-64-avx512_4fmaps_vl.s: Ditto. * testsuite/gas/i386/x86-64-avx512_4fmaps-intel.d: Ditto. * testsuite/gas/i386/x86-64-avx512_4fmaps.d: Ditto. * testsuite/gas/i386/x86-64-avx512_4fmaps.s: Ditto. * testsuite/gas/i386/x86-64-avx512_4fmaps-warn.l: Ditto. * testsuite/gas/i386/x86-64-avx512_4fmaps-warn.s: Ditto. * testsuite/gas/i386/x86-64-avx512_4fmaps_vl-warn.l: Ditto. * testsuite/gas/i386/x86-64-avx512_4fmaps_vl-warn.s: Ditto. opcodes/ * i386-dis.c. (enum): Add PREFIX_EVEX_0F389A, PREFIX_EVEX_0F389B, PREFIX_EVEX_0F38AA, PREFIX_EVEX_0F38AB. * i386-dis-evex.h (evex_table): Updated. * i386-gen.c (cpu_flag_init): Add CPU_AVX512_4FMAPS_FLAGS, CPU_ANY_AVX512_4FMAPS_FLAGS. Update CPU_ANY_AVX512F_FLAGS. (cpu_flags): Add CpuAVX512_4FMAPS. (opcode_modifiers): Add ImplicitQuadGroup modifier. * i386-opc.h (AVX512_4FMAP): New. (i386_cpu_flags): Add cpuavx512_4fmaps. (ImplicitQuadGroup): New. (i386_opcode_modifier): Add implicitquadgroup. * i386-opc.tbl: Add Intel AVX512_4FMAPS instructions. * i386-init.h: Regenerate. * i386-tbl.h: Ditto.
2016-11-01Add support for RISC-V architecture.Nick Clifton6-0/+1147
bfd * Makefile.am: Add entries for riscv32-elf and riscv64-elf. * config.bdf: Likewise. * configure.ac: Likewise. * Makefile.in: Regenerate. * configure: Regenerate. * archures.c: Add bfd_riscv_arch. * reloc.c: Add riscv relocs. * targets.c: Add riscv_elf32_vec and riscv_elf64_vec. * bfd-in2.h: Regenerate. * libbfd.h: Regenerate. * elf-bfd.h: Add RISCV_ELF_DATA to enum elf_target_id. * elfnn-riscv.c: New file. * elfxx-riscv.c: New file. * elfxx-riscv.h: New file. binutils* readelf.c (guess_is_rela): Add EM_RISCV. (get_machine_name): Likewise. (dump_relocations): Add support for riscv relocations. (get_machine_flags): Add support for riscv flags. (is_32bit_abs_reloc): Add R_RISCV_32. (is_64bit_abs_reloc): Add R_RISCV_64. (is_none_reloc): Add R_RISCV_NONE. * testsuite/binutils-all/objdump.exp (cpus_expected): Add riscv. Expect the debug_ranges test to fail. gas * Makefile.am: Add riscv files. * Makefile.in: Regenerate. * NEWS: Mention the support for this architecture. * configure.in: Define a default architecture. * configure: Regenerate. * configure.tgt: Add entries for riscv. * doc/as.texinfo: Likewise. * testsuite/gas/all/gas.exp: Expect the redef tests to fail. * testsuite/gas/elf/elf.exp: Expect the groupauto tests to fail. * config/tc-riscv.c: New file. * config/tc-riscv.h: New file. * doc/c-riscv.texi: New file. * testsuite/gas/riscv: New directory. * testsuite/gas/riscv/riscv.exp: New file. * testsuite/gas/riscv/t_insns.d: New file. * testsuite/gas/riscv/t_insns.s: New file. ld * Makefile.am: Add riscv files. * Makefile.in: Regenerate. * NEWS: Mention the support for this target. * configure.tgt: Add riscv entries. * emulparams/elf32lriscv-defs.sh: New file. * emulparams/elf32lriscv.sh: New file. * emulparams/elf64lriscv-defs.sh: New file. * emulparams/elf64lriscv.sh: New file. * emultempl/riscvelf.em: New file. opcodes * configure.ac: Add entry for bfd_riscv_arch. * configure: Regenerate. * disassemble.c (disassembler): Add support for riscv. (disassembler_usage): Likewise. * riscv-dis.c: New file. * riscv-opc.c: New file. include * dis-asm.h: Add prototypes for print_insn_riscv and print_riscv_disassembler_options. * elf/riscv.h: New file. * opcode/riscv-opc.h: New file. * opcode/riscv.h: New file.
2016-10-21X86: Remove pcommit instructionH.J. Lu7-5391/+5365
Remove x86 pcommit instruction support, which has been deprecated: https://software.intel.com/en-us/blogs/2016/09/12/deprecate-pcommit-instruction gas/ * config/tc-i386.c (cpu_arch): Remove .pcommit. * doc/c-i386.texi: Likewise. * testsuite/gas/i386/i386.exp: Remove pcommit tests. * testsuite/gas/i386/pcommit-intel.d: Removed. * testsuite/gas/i386/pcommit.d: Likewise. * testsuite/gas/i386/pcommit.s: Likewise. * testsuite/gas/i386/x86-64-pcommit-intel.d: Likewise. * testsuite/gas/i386/x86-64-pcommit.d: Likewise. * testsuite/gas/i386/x86-64-pcommit.s: Likewise. opcodes/ * i386-dis.c (PREFIX_RM_0_0FAE_REG_7): Removed. (prefix_table): Remove the PREFIX_RM_0_0FAE_REG_7 entry. (rm_table): Update the RM_0FAE_REG_7 entry. * i386-gen.c (cpu_flag_init): Remove CPU_PCOMMIT_FLAGS. (cpu_flags): Remove CpuPCOMMIT. * i386-opc.h (CpuPCOMMIT): Removed. (i386_cpu_flags): Remove cpupcommit. * i386-opc.tbl: Remove pcommit. * i386-init.h: Regenerated. * i386-tbl.h: Likewise.
2016-10-20Check invalid mask registersH.J. Lu2-17/+43
In 32-bit, the REX_B bit in the 3-byte VEX prefix is ignored and the the highest bit in VEX.vvvv is either 1 or ignored. In 64-bit, we need to check invalid mask registers. gas/ PR binutis/20705 * testsuite/gas/i386/i386.exp: Run x86-64-opcode-bad. * testsuite/gas/i386/x86-64-opcode-bad.d: New file. * testsuite/gas/i386/x86-64-opcode-bad.s: Likewise. opcodes/ PR binutis/20705 * i386-dis.c (get_valid_dis386): Ignore the REX_B bit and the highest bit in VEX.vvvv for the 3-byte VEX prefix in 32-bit mode. Don't check vex.register_specifier in 32-bit mode. (OP_E_register): Check invalid mask registers. (OP_G): Likewise. (OP_VEX): Likewise.
2016-10-18Check addr32flag instead of sizeflag for rip/eipH.J. Lu2-2/+8
Since the address size prefix, 0x67, is ignored for MPX instructions in 64-bit mode, we should check addr32flag instead of sizeflag for rip/eip. PR binutis/20699 * i386-dis.c (OP_E_memory): Check addr32flag instead of sizeflag for rip/eip.
2016-10-18Remove the remaining SSE5 supportH.J. Lu2-1/+6
PR binutis/20704 * i386-dis.c (three_byte_table): Remove the remaining SSE5 support.
2016-10-18AArch64/opcodes: Correct an `index' global shadowing errorMaciej W. Rozycki2-4/+9
Fix a commit 4df068de5214 ("Add support for SVE addressing modes") build regression: cc1: warnings being treated as errors .../opcodes/aarch64-dis.c: In function 'aarch64_ext_sve_addr_rr_lsl': .../opcodes/aarch64-dis.c:1324: error: declaration of 'index' shadows a global declaration /usr/include/string.h:303: error: shadowed declaration is here make[3]: *** [aarch64-dis.lo] Error 1 in a way following commit 91d6fa6a035c ("Add -Wshadow to the gcc command line options used when compiling the binutils."). opcodes/ * aarch64-dis.c (aarch64_ext_sve_addr_rr_lsl): Rename `index' local variable to `index_regno'.
2016-10-17Removed pseudo invalid instructions opcodes.Cupertino Miranda2-93/+4
The disassember was generating invXXX instructions for cases when in reality we had llockd or scondd instrutions. opcodes/ChangeLog: Cupertino Miranda <cmiranda@synopsys.com> arc-tbl.h: Removed any "inv.+" instructions from the table. gas/ChangeLog: Cupertino Miranda <cmiranda@synopsys.com> testsuite/arc/dis-inv.s: Test to validate patch. testsuite/arc/dis-inv.d: Likewise.
2016-10-14[ARC] Disassembler: fix LIMM detection for short instructions.Claudiu Zissulescu2-2/+8
The ARC (short) instructions are using a special register number to indicate is the instruction uses a long immediate (LIMM). In the case of short instruction, this LIMM indicator depends on the ISA version used. Thus, for ARCv1 processors, the LIMM indicator is 0x3E, the same value used in "long" instructions. However, for the ARCv2 processors, this LIMM indicator is 0x1E. This patch fixes the LIMM detection for ARCv1 ISA and adds two tests. gas/ 2016-10-13 Claudiu Zissulescu <claziss@synopsys.com> * testsuite/gas/arc/shortlimm_a7.d: New file. * testsuite/gas/arc/shortlimm_a7.s: Likewise. * testsuite/gas/arc/shortlimm_hs.d: Likewise. * testsuite/gas/arc/shortlimm_hs.s: Likewise. include/ 2016-10-13 Claudiu Zissulescu <claziss@synopsys.com> * opcode/arc.h (ARC_OPCODE_ARCV2): New define. opcodes/ 2016-10-13 Claudiu Zissulescu <claziss@synopsys.com> * arc-dis.c (find_format_from_table): Discriminate LIMM indicator usage on ISA basis.
2016-10-11[AArch64] PR target/20666, fix wrong encoding of new introduced BFC pseudoJiong Wang2-1/+6
opcode/ PR target/20666 * aarch64-asm.c (convert_bfc_to_bfm): Fix dest index. gas/ * testsuite/gas/aarch64/alias-2.d: Update expected results.
2016-10-07[AArch64] PR target/20667, fix disassembler for the "special" optional ↵Jiong Wang2-4/+14
SYS_Rt operand for "ic"/"tlbi" gas/ PR target/20667 * testsuite/gas/aarch64/sys-rt-reg.s: Test source for instructions using SYS_Rt reg. * testsuite/gas/aarch64/sys-rt-reg.d: New testcase. opcodes/ PR target/20667 * aarch64-opc.c (aarch64_print_operand): Always print operand if it's available.
2016-10-07bfd_merge_private_bfd_data tidyAlan Modra2-1/+4
bfd_merge_private_bfd_data and _bfd_generic_verify_endian_match are linker functions, so move them to linker.c. bfd/ * Makefile.am (LIBBFD_H_FILES): Update. * doc/Makefile.am (LIBBFD_H_DEP): Likewise. * cpu-sh.c (sh_merge_bfd_arch): Move to.. * elf32-sh.c: ..here, and make static. * elf32-arc.c (arc_elf_merge_private_bfd_data): Delete extraneous error. * elf32-cris.c (cris_elf_merge_private_bfd_data): Don't call _bfd_generic_verify_endian_match. * elf32-microblaze.c (microblaze_elf_merge_private_bfd_data): Delete. (bfd_elf32_bfd_merge_private_bfd_data): Define as _bfd_generic_verify_endian_match. * elf32-mt.c (mt_elf_merge_private_bfd_data): Don't test boolean == FALSE. * elf32-xgate.c (_bfd_xgate_elf_merge_private_bfd_data): Delete. (bfd_elf32_bfd_merge_private_bfd_data): Don't define. * elf32-xgate.h (_bfd_xgate_elf_merge_private_bfd_data): Delete. * libbfd-in.h (_bfd_generic_verify_endian_match): Delete. * libbfd.c (_bfd_generic_verify_endian_match): Move to.. * linker.c: ..here, and make internal. * bfd.c (bfd_merge_private_bfd_data): Move to.. * linker.c: ..here. * Makefile.in: Regenerate. * doc/Makefile.in: Regenerate. * bfd-in2.h: Regenerate. * libbfd.h: Regenerate. opcodes/ * sh-opc.h (sh_merge_bfd_arch): Delete prototype.
2016-10-06-Wimplicit-fallthrough warning fixesAlan Modra13-4/+47
Comment changes. bfd/ * coff-h8300.c: Spell fall through comments consistently. * coffgen.c: Likewise. * elf32-hppa.c: Likewise. * elf32-ppc.c: Likewise. * elf32-score.c: Likewise. * elf32-score7.c: Likewise. * elf64-ppc.c: Likewise. * elfxx-aarch64.c: Likewise. * elfxx-mips.c: Likewise. * cpu-ns32k.c: Add missing fall through comments. * elf-m10300.c: Likewise. * elf32-arm.c: Likewise. * elf32-avr.c: Likewise. * elf32-bfin.c: Likewise. * elf32-frv.c: Likewise. * elf32-i386.c: Likewise. * elf32-microblaze.c: Likewise. * elf32-nds32.c: Likewise. * elf32-ppc.c: Likewise. * elf32-rl78.c: Likewise. * elf32-rx.c: Likewise. * elf32-s390.c: Likewise. * elf32-sh.c: Likewise. * elf32-tic6x.c: Likewise. * elf64-ia64-vms.c: Likewise. * elf64-ppc.c: Likewise. * elf64-s390.c: Likewise. * elf64-x86-64.c: Likewise. * elflink.c: Likewise. * elfnn-aarch64.c: Likewise. * elfnn-ia64.c: Likewise. * ieee.c: Likewise. * oasys.c: Likewise. * pdp11.c: Likewise. * srec.c: Likewise. * versados.c: Likewise. opcodes/ * aarch64-opc.c: Spell fall through comments consistently. * i386-dis.c: Likewise. * aarch64-dis.c: Add missing fall through comments. * aarch64-opc.c: Likewise. * arc-dis.c: Likewise. * arm-dis.c: Likewise. * i386-dis.c: Likewise. * m68k-dis.c: Likewise. * mep-asm.c: Likewise. * ns32k-dis.c: Likewise. * sh-dis.c: Likewise. * tic4x-dis.c: Likewise. * tic6x-dis.c: Likewise. * vax-dis.c: Likewise. binutils/ * dlltool.c: Spell fall through comments consistently. * objcopy.c: Likewise. * readelf.c: Likewise. * dwarf.c: Add missing fall through comments. * elfcomm.c: Likewise. * sysinfo.y: Likewise. * readelf.c: Likewise. Also remove extraneous comments. gas/ * app.c: Add missing fall through comments. * dw2gencfi.c: Likewise. * expr.c: Likewise. * config/tc-alpha.c: Likewise. * config/tc-arc.c: Likewise. * config/tc-arm.c: Likewise. * config/tc-cr16.c: Likewise. * config/tc-crx.c: Likewise. * config/tc-dlx.c: Likewise. * config/tc-h8300.c: Likewise. * config/tc-hppa.c: Likewise. * config/tc-i370.c: Likewise. * config/tc-i386.c: Likewise. * config/tc-i960.c: Likewise. * config/tc-ia64.c: Likewise. * config/tc-m68hc11.c: Likewise. * config/tc-m68k.c: Likewise. * config/tc-mep.c: Likewise. * config/tc-metag.c: Likewise. * config/tc-microblaze.c: Likewise. * config/tc-mips.c: Likewise. * config/tc-ns32k.c: Likewise. * config/tc-rx.c: Likewise. * config/tc-score.c: Likewise. * config/tc-score7.c: Likewise. * config/tc-sh.c: Likewise. * config/tc-tic4x.c: Likewise. * config/tc-vax.c: Likewise. * config/tc-xstormy16.c: Likewise. * config/tc-z80.c: Likewise. * config/tc-z8k.c: Likewise. * config/obj-elf.c: Likewise. * config/tc-i386.c: Likewise. * depend.c: Spell fall through comments consistently. * config/tc-arm.c: Likewise. * config/tc-d10v.c: Likewise. * config/tc-i960.c: Likewise. * config/tc-ia64.c: Likewise. * config/tc-m68k.c: Likewise. * config/tc-mcore.c: Likewise. * config/tc-mep.c: Likewise. * config/tc-ns32k.c: Likewise. * config/tc-visium.c: Likewise. * config/tc-xstormy16.c: Likewise. * config/tc-z8k.c: Likewise. gprof/ * gprof.c: Add missing fall through comments. ld/ * lexsup.c: Spell fall through comments consistently and add missing fall through comments.
2016-10-06-Wimplicit-fallthrough error fixesAlan Modra4-99/+108
Well, not all are errors, but a little more substantive than just fiddling with comments. bfd/ * coffcode.h (coff_slurp_symbol_table): Revert accidental commit made 2015-01-08. * elf32-nds32.c (nds32_elf_grok_psinfo): Add missing break. * reloc.c (bfd_default_reloc_type_lookup): Add missing breaks. opcodes/ * arc-ext.c (create_map): Add missing break. * msp430-decode.opc (encode_as): Likewise. * msp430-decode.c: Regenerate. binutils/ * coffdump.c (dump_coff_where): Add missing break. * stabs.c (stab_xcoff_builtin_type): Likewise. gas/ * config/tc-arc.c (find_opcode_match): Add missing break. * config/tc-i960.c (get_cdisp): Likewise. * config/tc-metag.c (parse_swap, md_apply_fix): Likewise. * config/tc-mt.c (md_parse_option): Likewise. * config/tc-nds32.c (nds32_apply_fix): Likewise. * config/tc-hppa.c (pa_ip): Assert rather than testing last condition of multiple if statements. * config/tc-s390.c (s390_exp_compare): Return 0 on error. * config/tc-tic4x.c (tic4x_operand_parse): Add as_bad and break out of case rather than falling into next case. Formatting. ld/ * plugin.c (asymbol_from_plugin_symbol): Avoid compiler warning by adding return.
2016-10-06Don't use boolean OR in arithmetic expressionsAlan Modra3-2/+7
bfd/ * elf32-epiphany.c (epiphany_final_link_relocate): Use bitwise OR in arithmetic expression, not boolean OR. opcodes/ * cr16-dis.c (print_insn_cr16): Don't use boolean OR in arithmetic. * crx-dis.c (print_insn_crx): Likewise.
2016-09-30Don't assign alt twiceH.J. Lu2-1/+5
PR binutils/20657 * i386-dis.c (putop): Don't assign alt twice.
2016-09-30[AArch64] PR target/20553, fix opcode mask for SIMD multiply by elementJiong Wang2-4/+9
opcode/ PR target/20553 * aarch64-tbl.h (fmla, fmls, fmul, fmulx): Fix opcode mask field. gas/ * testsuite/gas/aarch64/advsimd-fp16.s (indexed_elem): New high index testcases for H and S variants. New low index testcases for D variant. * testsuite/gas/aarch64/advsimd-fp16.d: Update expected results.
2016-09-29Disallow 3-operand cmp[l][i] for ppc64Alan Modra2-73/+39
cmp[l][o] get an optional L field only when generating 32-bit code. dcbf, tlbie and tlbiel keep their optional L field, ditto for R field of tbegin. cmprb, tsr., wlcr[all] and mtsle all change to a compulsory L field. L field of dcbf and wclr is 2 bits. PR 20641 include/ * opcode/ppc.h (PPC_OPERAND_OPTIONAL32): Define. opcodes/ * ppc-opc.c (L): Make compulsory. (LOPT): New, optional form of L. (HTM_R): Define as LOPT. (L0, L1): Delete. (L32OPT): New, optional for 32-bit L. (L2OPT): New, 2-bit L for dcbf. (SVC_LEC): Update. (L2): Define. (insert_l0, extract_l0, insert_l1, extract_l2): Delete. (powerpc_opcodes <cmpli, cmpi, cmpl, cmp>): Use L32OPT. <dcbf>: Use L2OPT. <tlbiel, tlbie>: Use LOPT. <wclr, wclrall>: Use L2. gas/ * config/tc-ppc.c (md_assemble): Handle PPC_OPERAND_OPTIONAL32. * testsuite/gas/ppc/power8.s: Provide tbegin. operand. * testsuite/gas/ppc/power9.d: Update cmprb disassembly.
2016-09-26When building target binaries, ensure that the warning flags selected for ↵Vlad Zakharov3-6/+56
the command line match the target compiler. bfd * warning.m4 (AC_EGREP_CPP_FOR_BUILD): Introduce macro to verify CC_FOR_BUILD compiler. (AM_BINUTILS_WARNINGS): Introduce ac_cpp_for_build variable and add CC_FOR_BUILD compiler checks. * Makefile.in: Regenerate. * configure: Likewise. * doc/Makefile.in: Likewise. binutils * Makefile.am: Replace AM_CLFAGS with AM_CFLAGS_FOR_BUILD when building with CC_FOR_BUILD compiler. * Makefile.in: Regenerate. * configure: Likewise. * doc/Makefile.in: Likewise. gas * Makefile.in: Regenerate. * configure: Likewise. * doc/Makefile.in: Likewise. gold * Makefile.in: Regenerate. * configure: Likewise. * testsuite/Makefile.in: Likewise. gprof * Makefile.in: Regenerate. * configure: Likewise. ld * Makefile.in: Regenerate. * configure: Likewise. opcodes * Makefile.in: Regenerate. * configure: Likewise.
2016-09-26[ARC] ISA alignment.Claudiu Zissulescu4-35/+67
include/ 2016-09-26 Claudiu Zissulescu <claziss@synopsys.com> * opcode/arc.h (insn_class_t): Add two new classes. opcodes/ 2016-09-26 Claudiu Zissulescu <claziss@synopsys.com> * arc-ext-tbl.h (EXTINSN2OPF): Define. (EXTINSN2OP): Use EXTINSN2OPF. (bspeekm, bspop, modapp): New extension instructions. * arc-opc.c (F_DNZ_ND): Define. (F_DNZ_D): Likewise. (F_SIZEB1): Changed. (C_DNZ_D): Define. (C_HARD): Changed. * arc-tbl.h (dbnz): New instruction. (prealloc): Allow it for ARC EM. (xbfu): Likewise.
2016-09-21[AArch64] Print spaces after commas in addressesRichard Sandiford2-8/+14
I got an off-list request to make the AArch64 disassembler print spaces after commas in addresses. This patch does that. The same code is used to print operands in "did you mean" errors, so to keep things consistent, the patch also prints spaces between operands in those messages. opcodes/ * aarch64-opc.c (print_immediate_offset_address): Print spaces after commas in addresses. (aarch64_print_operand): Likewise. gas/ * config/tc-aarch64.c (print_operands): Print spaces between operands. * testsuite/gas/aarch64/ilp32-basic.d: Expect spaces after "," in addresses. * testsuite/gas/aarch64/ldst-reg-imm-post-ind.d: Likewise. * testsuite/gas/aarch64/ldst-reg-imm-pre-ind.d: Likewise. * testsuite/gas/aarch64/ldst-reg-pair.d: Likewise. * testsuite/gas/aarch64/ldst-reg-reg-offset.d: Likewise. * testsuite/gas/aarch64/ldst-reg-uns-imm.d: Likewise. * testsuite/gas/aarch64/ldst-reg-unscaled-imm.d: Likewise. * testsuite/gas/aarch64/reloc-insn.d: Likewise. * testsuite/gas/aarch64/sve.d: Likewise. * testsuite/gas/aarch64/symbol.d: Likewise. * testsuite/gas/aarch64/system.d: Likewise. * testsuite/gas/aarch64/tls-desc.d: Likewise. * testsuite/gas/aarch64/sve-invalid.l: Expect spaces after "," in suggested alternatives. * testsuite/gas/aarch64/verbose-error.l: Likewise. ld/ * testsuite/ld-aarch64/emit-relocs-28.d: Expect spaces after "," in addresses. * testsuite/ld-aarch64/emit-relocs-301-be.d: Likewise. * testsuite/ld-aarch64/emit-relocs-301.d: Likewise. * testsuite/ld-aarch64/emit-relocs-302-be.d: Likewise. * testsuite/ld-aarch64/emit-relocs-302.d: Likewise. * testsuite/ld-aarch64/emit-relocs-310-be.d: Likewise. * testsuite/ld-aarch64/emit-relocs-310.d: Likewise. * testsuite/ld-aarch64/emit-relocs-313.d: Likewise. * testsuite/ld-aarch64/emit-relocs-515-be.d: Likewise. * testsuite/ld-aarch64/emit-relocs-515.d: Likewise. * testsuite/ld-aarch64/emit-relocs-516-be.d: Likewise. * testsuite/ld-aarch64/emit-relocs-516.d: Likewise. * testsuite/ld-aarch64/emit-relocs-531.d: Likewise. * testsuite/ld-aarch64/emit-relocs-532.d: Likewise. * testsuite/ld-aarch64/emit-relocs-533.d: Likewise. * testsuite/ld-aarch64/emit-relocs-534.d: Likewise. * testsuite/ld-aarch64/emit-relocs-535.d: Likewise. * testsuite/ld-aarch64/emit-relocs-536.d: Likewise. * testsuite/ld-aarch64/emit-relocs-537.d: Likewise. * testsuite/ld-aarch64/emit-relocs-538.d: Likewise. * testsuite/ld-aarch64/erratum835769.d: Likewise. * testsuite/ld-aarch64/erratum843419.d: Likewise. * testsuite/ld-aarch64/farcall-b-plt.d: Likewise. * testsuite/ld-aarch64/farcall-bl-plt.d: Likewise. * testsuite/ld-aarch64/gc-plt-relocs.d: Likewise. * testsuite/ld-aarch64/ifunc-21.d: Likewise. * testsuite/ld-aarch64/ifunc-7c.d: Likewise. * testsuite/ld-aarch64/tls-desc-ie.d: Likewise. * testsuite/ld-aarch64/tls-large-desc-be.d: Likewise. * testsuite/ld-aarch64/tls-large-desc.d: Likewise. * testsuite/ld-aarch64/tls-large-ie-be.d: Likewise. * testsuite/ld-aarch64/tls-large-ie.d: Likewise. * testsuite/ld-aarch64/tls-relax-all.d: Likewise. * testsuite/ld-aarch64/tls-relax-gd-ie.d: Likewise. * testsuite/ld-aarch64/tls-relax-gdesc-ie-2.d: Likewise. * testsuite/ld-aarch64/tls-relax-gdesc-ie.d: Likewise. * testsuite/ld-aarch64/tls-relax-large-desc-ie-be.d: Likewise. * testsuite/ld-aarch64/tls-relax-large-desc-ie.d: Likewise. * testsuite/ld-aarch64/tls-tiny-desc.d: Likewise. * testsuite/ld-aarch64/tls-tiny-gd.d: Likewise.
2016-09-21[AArch64] Use "must" rather than "should" in error messagesRichard Sandiford2-3/+8
One of the review comments from the SVE series was that it would be better to use "must" rather than "should" in error messages. I think this patch fixes all cases in the AArch64 code. It also uses "must be" instead of "expected to be". opcodes/ * aarch64-opc.c (operand_general_constraint_met_p): Use "must be" rather than "should be" or "expected to be" in error messages. gas/ * config/tc-aarch64.c (output_operand_error_record): Use "must be" rather than "should be" or "expected to be" in error messages. (parse_operands): Likewise. * testsuite/gas/aarch64/diagnostic.l: Likewise. * testsuite/gas/aarch64/legacy_reg_names.l: Likewise. * testsuite/gas/aarch64/sve-invalid.l: Likewise. * testsuite/gas/aarch64/sve-reg-diagnostic.l: Likewise.
2016-09-21[AArch64] Add SVE condition codesRichard Sandiford3-20/+72
SVE defines new names for existing NZCV conditions, to reflect the result of instructions like PTEST. This patch adds support for these names. The patch also adds comments to the disassembly output to show the alternative names of a condition code. For example: cinv x0, x1, cc becomes: cinv x0, x1, cc // cc = lo, ul, last and: b.cc f0 <...> becomes: b.cc f0 <...> // b.lo, b.ul, b.last Doing this for the SVE names follows the practice recommended by the SVE specification and is definitely useful when reading SVE code. If the feeling is that it's too distracting elsewhere, we could add an option to turn it off. include/ * opcode/aarch64.h (aarch64_cond): Bump array size to 4. opcodes/ * aarch64-dis.c (remove_dot_suffix): New function, split out from... (print_mnemonic_name): ...here. (print_comment): New function. (print_aarch64_insn): Call it. * aarch64-opc.c (aarch64_conds): Add SVE names. (aarch64_print_operand): Print alternative condition names in a comment. gas/ * config/tc-aarch64.c (opcode_lookup): Search for the end of a condition name, rather than assuming that it will have exactly 2 characters. (parse_operands): Likewise. * testsuite/gas/aarch64/alias.d: Add new condition-code comments to the expected output. * testsuite/gas/aarch64/beq_1.d: Likewise. * testsuite/gas/aarch64/float-fp16.d: Likewise. * testsuite/gas/aarch64/int-insns.d: Likewise. * testsuite/gas/aarch64/no-aliases.d: Likewise. * testsuite/gas/aarch64/programmer-friendly.d: Likewise. * testsuite/gas/aarch64/reloc-insn.d: Likewise. * testsuite/gas/aarch64/b_c_1.d, testsuite/gas/aarch64/b_c_1.s: New test. ld/ * testsuite/ld-aarch64/emit-relocs-280.d: Match branch comments. * testsuite/ld-aarch64/weak-undefined.d: Likewise.
2016-09-21[AArch64][SVE 31/32] Add SVE instructionsRichard Sandiford8-116/+9454
This patch adds the SVE instruction definitions and associated OP_* enum values. include/ * opcode/aarch64.h (AARCH64_FEATURE_SVE): New macro. (OP_MOV_P_P, OP_MOV_Z_P_Z, OP_MOV_Z_V, OP_MOV_Z_Z, OP_MOV_Z_Zi) (OP_MOVM_P_P_P, OP_MOVS_P_P, OP_MOVZS_P_P_P, OP_MOVZ_P_P_P) (OP_NOTS_P_P_P_Z, OP_NOT_P_P_P_Z): New aarch64_ops. opcodes/ * aarch64-tbl.h (OP_SVE_B, OP_SVE_BB, OP_SVE_BBBU, OP_SVE_BMB) (OP_SVE_BPB, OP_SVE_BUB, OP_SVE_BUBB, OP_SVE_BUU, OP_SVE_BZ) (OP_SVE_BZB, OP_SVE_BZBB, OP_SVE_BZU, OP_SVE_DD, OP_SVE_DDD) (OP_SVE_DMD, OP_SVE_DMH, OP_SVE_DMS, OP_SVE_DU, OP_SVE_DUD, OP_SVE_DUU) (OP_SVE_DUV_BHS, OP_SVE_DUV_BHSD, OP_SVE_DZD, OP_SVE_DZU, OP_SVE_HB) (OP_SVE_HMD, OP_SVE_HMS, OP_SVE_HU, OP_SVE_HUU, OP_SVE_HZU, OP_SVE_RR) (OP_SVE_RURV_BHSD, OP_SVE_RUV_BHSD, OP_SVE_SMD, OP_SVE_SMH, OP_SVE_SMS) (OP_SVE_SU, OP_SVE_SUS, OP_SVE_SUU, OP_SVE_SZS, OP_SVE_SZU, OP_SVE_UB) (OP_SVE_UUD, OP_SVE_UUS, OP_SVE_VMR_BHSD, OP_SVE_VMU_SD) (OP_SVE_VMVD_BHS, OP_SVE_VMVU_BHSD, OP_SVE_VMVU_SD, OP_SVE_VMVV_BHSD) (OP_SVE_VMVV_SD, OP_SVE_VMV_BHSD, OP_SVE_VMV_HSD, OP_SVE_VMV_SD) (OP_SVE_VM_SD, OP_SVE_VPU_BHSD, OP_SVE_VPV_BHSD, OP_SVE_VRR_BHSD) (OP_SVE_VRU_BHSD, OP_SVE_VR_BHSD, OP_SVE_VUR_BHSD, OP_SVE_VUU_BHSD) (OP_SVE_VUVV_BHSD, OP_SVE_VUVV_SD, OP_SVE_VUV_BHSD, OP_SVE_VUV_SD) (OP_SVE_VU_BHSD, OP_SVE_VU_HSD, OP_SVE_VU_SD, OP_SVE_VVD_BHS) (OP_SVE_VVU_BHSD, OP_SVE_VVVU_SD, OP_SVE_VVV_BHSD, OP_SVE_VVV_SD) (OP_SVE_VV_BHSD, OP_SVE_VV_HSD_BHS, OP_SVE_VV_SD, OP_SVE_VWW_BHSD) (OP_SVE_VXX_BHSD, OP_SVE_VZVD_BHS, OP_SVE_VZVU_BHSD, OP_SVE_VZVV_BHSD) (OP_SVE_VZVV_SD, OP_SVE_VZV_SD, OP_SVE_V_SD, OP_SVE_WU, OP_SVE_WV_BHSD) (OP_SVE_XU, OP_SVE_XUV_BHSD, OP_SVE_XVW_BHSD, OP_SVE_XV_BHSD) (OP_SVE_XWU, OP_SVE_XXU): New macros. (aarch64_feature_sve): New variable. (SVE): New macro. (_SVE_INSN): Likewise. (aarch64_opcode_table): Add SVE instructions. * aarch64-opc.h (extract_fields): Declare. * aarch64-opc-2.c: Regenerate. * aarch64-asm.c (do_misc_encoding): Handle the new SVE aarch64_ops. * aarch64-asm-2.c: Regenerate. * aarch64-dis.c (extract_fields): Make global. (do_misc_decoding): Handle the new SVE aarch64_ops. * aarch64-dis-2.c: Regenerate. gas/ * doc/c-aarch64.texi: Document the "sve" feature. * config/tc-aarch64.c (REG_TYPE_R_Z_BHSDQ_VZP): New register type. (get_reg_expected_msg): Handle it. (parse_operands): When parsing operands of an SVE instruction, disallow immediates that match REG_TYPE_R_Z_BHSDQ_VZP. (aarch64_features): Add an entry for SVE.
2016-09-21[AArch64][SVE 30/32] Add SVE instruction classesRichard Sandiford5-0/+217
The main purpose of the SVE aarch64_insn_classes is to describe how an index into an aarch64_opnd_qualifier_seq_t is represented in the instruction encoding. Other instructions usually use flags for this information, but (a) we're running out of those and (b) the iclass would otherwise be unused for SVE. include/ * opcode/aarch64.h (sve_cpy, sve_index, sve_limm, sve_misc) (sve_movprfx, sve_pred_zm, sve_shift_pred, sve_shift_unpred) (sve_size_bhs, sve_size_bhsd, sve_size_hsd, sve_size_sd): New aarch64_insn_classes. opcodes/ * aarch64-opc.h (FLD_SVE_M_4, FLD_SVE_M_14, FLD_SVE_M_16) (FLD_SVE_sz, FLD_SVE_tsz, FLD_SVE_tszl_8, FLD_SVE_tszl_19): New aarch64_field_kinds. * aarch64-opc.c (fields): Add corresponding entries. * aarch64-asm.c (aarch64_get_variant): New function. (aarch64_encode_variant_using_iclass): Likewise. (aarch64_opcode_encode): Call it. * aarch64-dis.c (aarch64_decode_variant_using_iclass): New function. (aarch64_opcode_decode): Call it.
2016-09-21[AArch64][SVE 29/32] Add new SVE core & FP register operandsRichard Sandiford7-20/+75
SVE uses some new fields to store W, X and scalar FP registers. This patch adds corresponding operands. include/ * opcode/aarch64.h (AARCH64_OPND_SVE_Rm): New aarch64_opnd. (AARCH64_OPND_SVE_Rn_SP, AARCH64_OPND_SVE_VZn, AARCH64_OPND_SVE_Vd) (AARCH64_OPND_SVE_Vm, AARCH64_OPND_SVE_Vn): Likewise. opcodes/ * aarch64-tbl.h (AARCH64_OPERANDS): Add entries for the new SVE core and FP register operands. * aarch64-opc.h (FLD_SVE_Rm, FLD_SVE_Rn, FLD_SVE_Vd, FLD_SVE_Vm) (FLD_SVE_Vn): New aarch64_field_kinds. * aarch64-opc.c (fields): Add corresponding entries. (aarch64_print_operand): Handle the new SVE core and FP register operands. * aarch64-opc-2.c: Regenerate. * aarch64-asm-2.c: Likewise. * aarch64-dis-2.c: Likewise. gas/ * config/tc-aarch64.c (parse_operands): Handle the new SVE core and FP register operands.
2016-09-21[AArch64][SVE 28/32] Add SVE FP immediate operandsRichard Sandiford11-50/+239
This patch adds support for the new SVE floating-point immediate operands. One operand uses the same 8-bit encoding as base AArch64, but in a different position. The others use a single bit to select between two values. One of the single-bit operands is a choice between 0 and 1, where 0 is not a valid 8-bit encoding. I think the cleanest way of handling these single-bit immediates is therefore to use the IEEE float encoding itself as the immediate value and select between the two possible values when encoding and decoding. As described in the covering note for the patch that added F_STRICT, we get better error messages by accepting unsuffixed vector registers and leaving the qualifier matching code to report an error. This means that we carry on parsing the other operands, and so can try to parse FP immediates for invalid instructions like: fcpy z0, #2.5 In this case there is no suffix to tell us whether the immediate should be treated as single or double precision. Again, we get better error messages by picking one (arbitrary) immediate size and reporting an error for the missing suffix later. include/ * opcode/aarch64.h (AARCH64_OPND_SVE_FPIMM8): New aarch64_opnd. (AARCH64_OPND_SVE_I1_HALF_ONE, AARCH64_OPND_SVE_I1_HALF_TWO) (AARCH64_OPND_SVE_I1_ZERO_ONE): Likewise. opcodes/ * aarch64-tbl.h (AARCH64_OPERANDS): Add entries for the new SVE FP immediate operands. * aarch64-opc.h (FLD_SVE_i1): New aarch64_field_kind. * aarch64-opc.c (fields): Add corresponding entry. (operand_general_constraint_met_p): Handle the new SVE FP immediate operands. (aarch64_print_operand): Likewise. * aarch64-opc-2.c: Regenerate. * aarch64-asm.h (ins_sve_float_half_one, ins_sve_float_half_two) (ins_sve_float_zero_one): New inserters. * aarch64-asm.c (aarch64_ins_sve_float_half_one): New function. (aarch64_ins_sve_float_half_two): Likewise. (aarch64_ins_sve_float_zero_one): Likewise. * aarch64-asm-2.c: Regenerate. * aarch64-dis.h (ext_sve_float_half_one, ext_sve_float_half_two) (ext_sve_float_zero_one): New extractors. * aarch64-dis.c (aarch64_ext_sve_float_half_one): New function. (aarch64_ext_sve_float_half_two): Likewise. (aarch64_ext_sve_float_zero_one): Likewise. * aarch64-dis-2.c: Regenerate. gas/ * config/tc-aarch64.c (double_precision_operand_p): New function. (parse_operands): Use it to calculate the dp_p input to parse_aarch64_imm_float. Handle the new SVE FP immediate operands.
2016-09-21[AArch64][SVE 27/32] Add SVE integer immediate operandsRichard Sandiford11-100/+647
This patch adds the new SVE integer immediate operands. There are three kinds: - simple signed and unsigned ranges, but with new widths and positions. - 13-bit logical immediates. These have the same form as in base AArch64, but at a different bit position. In the case of the "MOV Zn.<T>, #<limm>" alias of DUPM, the logical immediate <limm> is not allowed to be a valid DUP immediate, since DUP is preferred over DUPM for constants that both instructions can handle. - a new 9-bit arithmetic immediate, of the form "<imm8>{, LSL #8}". In some contexts the operand is signed and in others it's unsigned. As an extension, we allow shifted immediates to be written as a single integer, e.g. "#256" is equivalent to "#1, LSL #8". We also use the shiftless form as the preferred disassembly, except for the special case of "#0, LSL #8" (a redundant encoding of 0). include/ * opcode/aarch64.h (AARCH64_OPND_SIMM5): New aarch64_opnd. (AARCH64_OPND_SVE_AIMM, AARCH64_OPND_SVE_ASIMM) (AARCH64_OPND_SVE_INV_LIMM, AARCH64_OPND_SVE_LIMM) (AARCH64_OPND_SVE_LIMM_MOV, AARCH64_OPND_SVE_SHLIMM_PRED) (AARCH64_OPND_SVE_SHLIMM_UNPRED, AARCH64_OPND_SVE_SHRIMM_PRED) (AARCH64_OPND_SVE_SHRIMM_UNPRED, AARCH64_OPND_SVE_SIMM5) (AARCH64_OPND_SVE_SIMM5B, AARCH64_OPND_SVE_SIMM6) (AARCH64_OPND_SVE_SIMM8, AARCH64_OPND_SVE_UIMM3) (AARCH64_OPND_SVE_UIMM7, AARCH64_OPND_SVE_UIMM8) (AARCH64_OPND_SVE_UIMM8_53): Likewise. (aarch64_sve_dupm_mov_immediate_p): Declare. opcodes/ * aarch64-tbl.h (AARCH64_OPERANDS): Add entries for the new SVE integer immediate operands. * aarch64-opc.h (FLD_SVE_immN, FLD_SVE_imm3, FLD_SVE_imm5) (FLD_SVE_imm5b, FLD_SVE_imm7, FLD_SVE_imm8, FLD_SVE_imm9) (FLD_SVE_immr, FLD_SVE_imms, FLD_SVE_tszh): New aarch64_field_kinds. * aarch64-opc.c (fields): Add corresponding entries. (operand_general_constraint_met_p): Handle the new SVE integer immediate operands. (aarch64_print_operand): Likewise. (aarch64_sve_dupm_mov_immediate_p): New function. * aarch64-opc-2.c: Regenerate. * aarch64-asm.h (ins_inv_limm, ins_sve_aimm, ins_sve_asimm) (ins_sve_limm_mov, ins_sve_shlimm, ins_sve_shrimm): New inserters. * aarch64-asm.c (aarch64_ins_limm_1): New function, split out from... (aarch64_ins_limm): ...here. (aarch64_ins_inv_limm): New function. (aarch64_ins_sve_aimm): Likewise. (aarch64_ins_sve_asimm): Likewise. (aarch64_ins_sve_limm_mov): Likewise. (aarch64_ins_sve_shlimm): Likewise. (aarch64_ins_sve_shrimm): Likewise. * aarch64-asm-2.c: Regenerate. * aarch64-dis.h (ext_inv_limm, ext_sve_aimm, ext_sve_asimm) (ext_sve_limm_mov, ext_sve_shlimm, ext_sve_shrimm): New extractors. * aarch64-dis.c (decode_limm): New function, split out from... (aarch64_ext_limm): ...here. (aarch64_ext_inv_limm): New function. (decode_sve_aimm): Likewise. (aarch64_ext_sve_aimm): Likewise. (aarch64_ext_sve_asimm): Likewise. (aarch64_ext_sve_limm_mov): Likewise. (aarch64_top_bit): Likewise. (aarch64_ext_sve_shlimm): Likewise. (aarch64_ext_sve_shrimm): Likewise. * aarch64-dis-2.c: Regenerate. gas/ * config/tc-aarch64.c (parse_operands): Handle the new SVE integer immediate operands.
2016-09-21[AArch64][SVE 26/32] Add SVE MUL VL addressing modesRichard Sandiford10-38/+290
This patch adds support for addresses of the form: [<base>, #<offset>, MUL VL] This involves adding a new AARCH64_MOD_MUL_VL modifier, which is why I split it out from the other addressing modes. For LD2, LD3 and LD4, the offset must be a multiple of the structure size, so for LD3 the possible values are 0, 3, 6, .... The patch therefore extends value_aligned_p to handle non-power-of-2 alignments. include/ * opcode/aarch64.h (AARCH64_OPND_SVE_ADDR_RI_S4xVL): New aarch64_opnd. (AARCH64_OPND_SVE_ADDR_RI_S4x2xVL, AARCH64_OPND_SVE_ADDR_RI_S4x3xVL) (AARCH64_OPND_SVE_ADDR_RI_S4x4xVL, AARCH64_OPND_SVE_ADDR_RI_S6xVL) (AARCH64_OPND_SVE_ADDR_RI_S9xVL): Likewise. (AARCH64_MOD_MUL_VL): New aarch64_modifier_kind. opcodes/ * aarch64-tbl.h (AARCH64_OPERANDS): Add entries for new MUL VL operands. * aarch64-opc.c (aarch64_operand_modifiers): Initialize the AARCH64_MOD_MUL_VL entry. (value_aligned_p): Cope with non-power-of-two alignments. (operand_general_constraint_met_p): Handle the new MUL VL addresses. (print_immediate_offset_address): Likewise. (aarch64_print_operand): Likewise. * aarch64-opc-2.c: Regenerate. * aarch64-asm.h (ins_sve_addr_ri_s4xvl, ins_sve_addr_ri_s6xvl) (ins_sve_addr_ri_s9xvl): New inserters. * aarch64-asm.c (aarch64_ins_sve_addr_ri_s4xvl): New function. (aarch64_ins_sve_addr_ri_s6xvl): Likewise. (aarch64_ins_sve_addr_ri_s9xvl): Likewise. * aarch64-asm-2.c: Regenerate. * aarch64-dis.h (ext_sve_addr_ri_s4xvl, ext_sve_addr_ri_s6xvl) (ext_sve_addr_ri_s9xvl): New extractors. * aarch64-dis.c (aarch64_ext_sve_addr_reg_mul_vl): New function. (aarch64_ext_sve_addr_ri_s4xvl): Likewise. (aarch64_ext_sve_addr_ri_s6xvl): Likewise. (aarch64_ext_sve_addr_ri_s9xvl): Likewise. * aarch64-dis-2.c: Regenerate. gas/ * config/tc-aarch64.c (SHIFTED_NONE, SHIFTED_MUL_VL): New parse_shift_modes. (parse_shift): Handle SHIFTED_MUL_VL. (parse_address_main): Add an imm_shift_mode parameter. (parse_address, parse_sve_address): Update accordingly. (parse_operands): Handle MUL VL addressing modes.
2016-09-21[AArch64][SVE 25/32] Add support for SVE addressing modesRichard Sandiford11-41/+739
This patch adds most of the new SVE addressing modes and associated operands. A follow-on patch adds MUL VL, since handling it separately makes the changes easier to read. The patch also introduces a new "operand-dependent data" field to the operand flags, based closely on the existing one for opcode flags. For SVE this new field needs only 2 bits, but it could be widened in future if necessary. include/ * opcode/aarch64.h (AARCH64_OPND_SVE_ADDR_RI_U6): New aarch64_opnd. (AARCH64_OPND_SVE_ADDR_RI_U6x2, AARCH64_OPND_SVE_ADDR_RI_U6x4) (AARCH64_OPND_SVE_ADDR_RI_U6x8, AARCH64_OPND_SVE_ADDR_RR) (AARCH64_OPND_SVE_ADDR_RR_LSL1, AARCH64_OPND_SVE_ADDR_RR_LSL2) (AARCH64_OPND_SVE_ADDR_RR_LSL3, AARCH64_OPND_SVE_ADDR_RX) (AARCH64_OPND_SVE_ADDR_RX_LSL1, AARCH64_OPND_SVE_ADDR_RX_LSL2) (AARCH64_OPND_SVE_ADDR_RX_LSL3, AARCH64_OPND_SVE_ADDR_RZ) (AARCH64_OPND_SVE_ADDR_RZ_LSL1, AARCH64_OPND_SVE_ADDR_RZ_LSL2) (AARCH64_OPND_SVE_ADDR_RZ_LSL3, AARCH64_OPND_SVE_ADDR_RZ_XTW_14) (AARCH64_OPND_SVE_ADDR_RZ_XTW_22, AARCH64_OPND_SVE_ADDR_RZ_XTW1_14) (AARCH64_OPND_SVE_ADDR_RZ_XTW1_22, AARCH64_OPND_SVE_ADDR_RZ_XTW2_14) (AARCH64_OPND_SVE_ADDR_RZ_XTW2_22, AARCH64_OPND_SVE_ADDR_RZ_XTW3_14) (AARCH64_OPND_SVE_ADDR_RZ_XTW3_22, AARCH64_OPND_SVE_ADDR_ZI_U5) (AARCH64_OPND_SVE_ADDR_ZI_U5x2, AARCH64_OPND_SVE_ADDR_ZI_U5x4) (AARCH64_OPND_SVE_ADDR_ZI_U5x8, AARCH64_OPND_SVE_ADDR_ZZ_LSL) (AARCH64_OPND_SVE_ADDR_ZZ_SXTW, AARCH64_OPND_SVE_ADDR_ZZ_UXTW): Likewise. opcodes/ * aarch64-tbl.h (AARCH64_OPERANDS): Add entries for the new SVE address operands. * aarch64-opc.h (FLD_SVE_imm6, FLD_SVE_msz, FLD_SVE_xs_14) (FLD_SVE_xs_22): New aarch64_field_kinds. (OPD_F_OD_MASK, OPD_F_OD_LSB, OPD_F_NO_ZR): New flags. (get_operand_specific_data): New function. * aarch64-opc.c (fields): Add entries for FLD_SVE_imm6, FLD_SVE_msz, FLD_SVE_xs_14 and FLD_SVE_xs_22. (operand_general_constraint_met_p): Handle the new SVE address operands. (sve_reg): New array. (get_addr_sve_reg_name): New function. (aarch64_print_operand): Handle the new SVE address operands. * aarch64-opc-2.c: Regenerate. * aarch64-asm.h (ins_sve_addr_ri_u6, ins_sve_addr_rr_lsl) (ins_sve_addr_rz_xtw, ins_sve_addr_zi_u5, ins_sve_addr_zz_lsl) (ins_sve_addr_zz_sxtw, ins_sve_addr_zz_uxtw): New inserters. * aarch64-asm.c (aarch64_ins_sve_addr_ri_u6): New function. (aarch64_ins_sve_addr_rr_lsl): Likewise. (aarch64_ins_sve_addr_rz_xtw): Likewise. (aarch64_ins_sve_addr_zi_u5): Likewise. (aarch64_ins_sve_addr_zz): Likewise. (aarch64_ins_sve_addr_zz_lsl): Likewise. (aarch64_ins_sve_addr_zz_sxtw): Likewise. (aarch64_ins_sve_addr_zz_uxtw): Likewise. * aarch64-asm-2.c: Regenerate. * aarch64-dis.h (ext_sve_addr_ri_u6, ext_sve_addr_rr_lsl) (ext_sve_addr_rz_xtw, ext_sve_addr_zi_u5, ext_sve_addr_zz_lsl) (ext_sve_addr_zz_sxtw, ext_sve_addr_zz_uxtw): New extractors. * aarch64-dis.c (aarch64_ext_sve_add_reg_imm): New function. (aarch64_ext_sve_addr_ri_u6): Likewise. (aarch64_ext_sve_addr_rr_lsl): Likewise. (aarch64_ext_sve_addr_rz_xtw): Likewise. (aarch64_ext_sve_addr_zi_u5): Likewise. (aarch64_ext_sve_addr_zz): Likewise. (aarch64_ext_sve_addr_zz_lsl): Likewise. (aarch64_ext_sve_addr_zz_sxtw): Likewise. (aarch64_ext_sve_addr_zz_uxtw): Likewise. * aarch64-dis-2.c: Regenerate. gas/ * config/tc-aarch64.c (REG_TYPE_SVE_BASE, REG_TYPE_SVE_OFFSET): New register types. (get_reg_expected_msg): Handle them. (aarch64_addr_reg_parse): New function, split out from aarch64_reg_parse_32_64. Handle Z registers too. (aarch64_reg_parse_32_64): Call it. (parse_address_main): Add base_qualifier, offset_qualifier, base_type and offset_type parameters. Handle SVE base and offset registers. (parse_address): Update call to parse_address_main. (parse_sve_address): New function. (parse_operands): Parse the new SVE address operands.
2016-09-21[AArch64][SVE 24/32] Add AARCH64_OPND_SVE_PATTERN_SCALEDRichard Sandiford11-17/+126
Some SVE instructions count the number of elements in a given vector pattern and allow a scale factor of [1, 16] to be applied to the result. This scale factor is written ", MUL #n", where "MUL" is a new operator. E.g.: UQINCD X0, POW2, MUL #2 This patch adds support for this kind of operand. All existing operators were shifts of some kind, so there was a natural range of [0, 63] regardless of context. This was then narrowered further by later checks (e.g. to [0, 31] when used for 32-bit values). In contrast, MUL doesn't really have a natural context-independent range. Rather than pick one arbitrarily, it seemed better to make the "shift" amount a full 64-bit value and leave the range test to the usual operand-checking code. I've rearranged the fields of aarch64_opnd_info so that this doesn't increase the size of the structure (although I don't think its size is critical anyway). include/ * opcode/aarch64.h (AARCH64_OPND_SVE_PATTERN_SCALED): New aarch64_opnd. (AARCH64_MOD_MUL): New aarch64_modifier_kind. (aarch64_opnd_info): Make shifter.amount an int64_t and rearrange the fields. opcodes/ * aarch64-tbl.h (AARCH64_OPERANDS): Add an entry for AARCH64_OPND_SVE_PATTERN_SCALED. * aarch64-opc.h (FLD_SVE_imm4): New aarch64_field_kind. * aarch64-opc.c (fields): Add a corresponding entry. (set_multiplier_out_of_range_error): New function. (aarch64_operand_modifiers): Add entry for AARCH64_MOD_MUL. (operand_general_constraint_met_p): Handle AARCH64_OPND_SVE_PATTERN_SCALED. (print_register_offset_address): Use PRIi64 to print the shift amount. (aarch64_print_operand): Likewise. Handle AARCH64_OPND_SVE_PATTERN_SCALED. * aarch64-opc-2.c: Regenerate. * aarch64-asm.h (ins_sve_scale): New inserter. * aarch64-asm.c (aarch64_ins_sve_scale): New function. * aarch64-asm-2.c: Regenerate. * aarch64-dis.h (ext_sve_scale): New inserter. * aarch64-dis.c (aarch64_ext_sve_scale): New function. * aarch64-dis-2.c: Regenerate. gas/ * config/tc-aarch64.c (SHIFTED_MUL): New parse_shift_mode. (parse_shift): Handle it. Reject AARCH64_MOD_MUL for all other shift modes. Skip range tests for AARCH64_MOD_MUL. (process_omitted_operand): Handle AARCH64_OPND_SVE_PATTERN_SCALED. (parse_operands): Likewise.
2016-09-21[AArch64][SVE 23/32] Add SVE pattern and prfop operandsRichard Sandiford7-11/+127
The SVE instructions have two enumerated operands: one to select a vector pattern and another to select a prefetch operation. The latter is a cut-down version of the base AArch64 prefetch operation. Both types of operand can also be specified as raw enum values such as #31. Reserved values can only be specified this way. If it hadn't been for the pattern operand, I would have been tempted to use the existing parsing for prefetch operations and add extra checks for SVE. However, since the patterns needed new enum parsing code anyway, it seeemed cleaner to reuse it for the prefetches too. Because of the small number of enum values, I don't think we'd gain anything by using hash tables. include/ * opcode/aarch64.h (AARCH64_OPND_SVE_PATTERN): New aarch64_opnd. (AARCH64_OPND_SVE_PRFOP): Likewise. (aarch64_sve_pattern_array): Declare. (aarch64_sve_prfop_array): Likewise. opcodes/ * aarch64-tbl.h (AARCH64_OPERANDS): Add entries for AARCH64_OPND_SVE_PATTERN and AARCH64_OPND_SVE_PRFOP. * aarch64-opc.h (FLD_SVE_pattern): New aarch64_field_kind. (FLD_SVE_prfop): Likewise. * aarch64-opc.c: Include libiberty.h. (aarch64_sve_pattern_array): New variable. (aarch64_sve_prfop_array): Likewise. (fields): Add entries for FLD_SVE_pattern and FLD_SVE_prfop. (aarch64_print_operand): Handle AARCH64_OPND_SVE_PATTERN and AARCH64_OPND_SVE_PRFOP. * aarch64-asm-2.c: Regenerate. * aarch64-dis-2.c: Likewise. * aarch64-opc-2.c: Likewise. gas/ * config/tc-aarch64.c (parse_enum_string): New function. (po_enum_or_fail): New macro. (parse_operands): Handle AARCH64_OPND_SVE_PATTERN and AARCH64_OPND_SVE_PRFOP.
2016-09-21[AArch64][SVE 22/32] Add qualifiers for merging and zeroing predicationRichard Sandiford2-0/+13
This patch adds qualifiers to represent /z and /m suffixes on predicate registers. include/ * opcode/aarch64.h (AARCH64_OPND_QLF_P_Z): New aarch64_opnd_qualifier. (AARCH64_OPND_QLF_P_M): Likewise. opcodes/ * aarch64-opc.c (aarch64_opnd_qualifiers): Add entries for AARCH64_OPND_QLF_P_[ZM]. (aarch64_print_operand): Print /z and /m where appropriate. gas/ * config/tc-aarch64.c (vector_el_type): Add NT_zero and NT_merge. (parse_vector_type_for_operand): Assert that the skipped character is a '.'. (parse_predication_for_operand): New function. (parse_typed_reg): Parse /z and /m suffixes for predicate registers. (vectype_to_qualifier): Handle NT_zero and NT_merge.
2016-09-21[AArch64][SVE 21/32] Add Zn and Pn registersRichard Sandiford11-1/+291
This patch adds the Zn and Pn registers, and associated fields and operands. include/ * opcode/aarch64.h (AARCH64_OPND_CLASS_SVE_REG): New aarch64_operand_class. (AARCH64_OPND_CLASS_PRED_REG): Likewise. (AARCH64_OPND_SVE_Pd, AARCH64_OPND_SVE_Pg3, AARCH64_OPND_SVE_Pg4_5) (AARCH64_OPND_SVE_Pg4_10, AARCH64_OPND_SVE_Pg4_16) (AARCH64_OPND_SVE_Pm, AARCH64_OPND_SVE_Pn, AARCH64_OPND_SVE_Pt) (AARCH64_OPND_SVE_Za_5, AARCH64_OPND_SVE_Za_16, AARCH64_OPND_SVE_Zd) (AARCH64_OPND_SVE_Zm_5, AARCH64_OPND_SVE_Zm_16, AARCH64_OPND_SVE_Zn) (AARCH64_OPND_SVE_Zn_INDEX, AARCH64_OPND_SVE_ZnxN) (AARCH64_OPND_SVE_Zt, AARCH64_OPND_SVE_ZtxN): New aarch64_opnds. opcodes/ * aarch64-tbl.h (AARCH64_OPERANDS): Add entries for new SVE operands. * aarch64-opc.h (FLD_SVE_Pd, FLD_SVE_Pg3, FLD_SVE_Pg4_5) (FLD_SVE_Pg4_10, FLD_SVE_Pg4_16, FLD_SVE_Pm, FLD_SVE_Pn, FLD_SVE_Pt) (FLD_SVE_Za_5, FLD_SVE_Za_16, FLD_SVE_Zd, FLD_SVE_Zm_5, FLD_SVE_Zm_16) (FLD_SVE_Zn, FLD_SVE_Zt, FLD_SVE_tzsh): New aarch64_field_kinds. * aarch64-opc.c (fields): Add corresponding entries here. (operand_general_constraint_met_p): Check that SVE register lists have the correct length. Check the ranges of SVE index registers. Check for cases where p8-p15 are used in 3-bit predicate fields. (aarch64_print_operand): Handle the new SVE operands. * aarch64-opc-2.c: Regenerate. * aarch64-asm.h (ins_sve_index, ins_sve_reglist): New inserters. * aarch64-asm.c (aarch64_ins_sve_index): New function. (aarch64_ins_sve_reglist): Likewise. * aarch64-asm-2.c: Regenerate. * aarch64-dis.h (ext_sve_index, ext_sve_reglist): New extractors. * aarch64-dis.c (aarch64_ext_sve_index): New function. (aarch64_ext_sve_reglist): Likewise. * aarch64-dis-2.c: Regenerate. gas/ * config/tc-aarch64.c (NTA_HASVARWIDTH): New macro. (AARCH64_REG_TYPES): Add ZN and PN. (get_reg_expected_msg): Handle them. (parse_vector_type_for_operand): Add a reg_type parameter. Skip the width for Zn and Pn registers. (parse_typed_reg): Extend vector handling to Zn and Pn. Update the call to parse_vector_type_for_operand. Set HASVARTYPE for Zn and Pn, expecting the width to be 0. (parse_vector_reg_list): Restrict error about [BHSD]nn operands to REG_TYPE_VN. (vectype_to_qualifier): Use S_[BHSD] qualifiers for NTA_HASVARWIDTH. (parse_operands): Handle the new Zn and Pn operands. (REGSET16): New macro, split out from... (REGSET31): ...here. (reg_names): Add Zn and Pn entries.
2016-09-21[AArch64][SVE 20/32] Add support for tied operandsRichard Sandiford3-16/+41
SVE has some instructions in which the same register appears twice in the assembly string, once as an input and once as an output. This patch adds a general mechanism for that. The patch needs to add new information to the instruction entries. One option would have been to extend the flags field of the opcode to 64 bits (since we already rely on 64-bit integers being available on the host). However, the *_INSN macros mean that it's easy to add new information as top-level fields without affecting the existing table entries too much. Going for that option seemed to give slightly neater code. include/ * opcode/aarch64.h (aarch64_opcode): Add a tied_operand field. (AARCH64_OPDE_UNTIED_OPERAND): New aarch64_operand_error_kind. opcodes/ * aarch64-tbl.h (CORE_INSN, __FP_INSN, SIMD_INSN, CRYP_INSN) (_CRC_INSN, _LSE_INSN, _LOR_INSN, RDMA_INSN, FP16_INSN, SF16_INSN) (V8_2_INSN, aarch64_opcode_table): Initialize tied_operand field. * aarch64-opc.c (aarch64_match_operands_constraint): Check for tied operands. gas/ * config/tc-aarch64.c (output_operand_error_record): Handle AARCH64_OPDE_UNTIED_OPERAND.
generated by cgit v1.1 at 2024-07-14 18:38:09 +0000