Age | Commit message (Collapse) | Author | Files | Lines |
|
APX uses the REX2 prefix to support EGPR for map0 and map1 of legacy
instructions. We added the NoEgpr flag in i386-gen.c for instructions
that do not support EGPR.
gas/ChangeLog:
2023-12-28 Lingling Kong <lingling.kong@intel.com>
H.J. Lu <hongjiu.lu@intel.com>
Lili Cui <lili.cui@intel.com>
Lin Hu <lin1.hu@intel.com>
* config/tc-i386.c
(enum i386_error): Add unsupported_EGPR_for_addressing
and invalid_pseudo_prefix.
(struct _i386_insn): Add rex2 and rex2_encoding for
gpr32.
(cpu_arch): Add apx_f.
(is_cpu): Ditto.
(register_number): Handle RegRex2 for gpr32.
(is_apx_rex2_encoding): New func. Test rex2 prefix encoding.
(build_rex2_prefix): New func. Build legacy insn in
opcode 0/1 use gpr32 with rex2 prefix.
(establish_rex): Handle rex2 and rex2_encoding.
(optimize_encoding): Handel add r16-r31 for registers.
(md_assemble): Handle apx encoding.
(parse_insn): Handle Prefix_REX2.
(check_EgprOperands): New func. Check if Egprs operands
are valid for the instruction
(match_template): Handle Egpr operands check.
(set_rex_rex2): New func. set i.rex and i.rex2.
(build_modrm_byte): Ditto.
(output_insn): Handle rex2 2-byte prefix output.
(check_register): Handle check egpr illegal without
target apx, 64-bit mode and with rex_prefix.
* doc/c-i386.texi: Document .apx.
* testsuite/gas/i386/ilp32/x86-64-opcode-inval-intel.d: D5 valid
in 64-bit mode.
* testsuite/gas/i386/ilp32/x86-64-opcode-inval.d: Ditto.
* testsuite/gas/i386/rex-bad: Adjust rex testcase.
* testsuite/gas/i386/x86-64-opcode-inval-intel.d: Ditto.
* testsuite/gas/i386/x86-64-opcode-inval.d: Ditto.
* testsuite/gas/i386/x86-64-opcode-inval.s: Ditto.
* testsuite/gas/i386/x86-64-pseudos-bad.l: Add illegal rex2 test.
* testsuite/gas/i386/x86-64-pseudos-bad.s: Ditto.
* testsuite/gas/i386/x86-64-pseudos.d: Add rex2 test.
* testsuite/gas/i386/x86-64-pseudos.s: Ditto.
* testsuite/gas/i386/x86-64.exp: Run APX tests.
* testsuite/gas/i386/x86-64-apx-egpr-inval.l: New test.
* testsuite/gas/i386/x86-64-apx-egpr-inval.s: New test.
* testsuite/gas/i386/x86-64-apx-rex2.d: New test.
* testsuite/gas/i386/x86-64-apx-rex2.s: New test.
include/ChangeLog:
* opcode/i386.h (REX2_OPCODE): New.
(REX2_M): Ditto.
opcodes/ChangeLog:
* i386-dis.c (struct instr_info): Add erex for gpr32.
Add last_erex_prefix for rex2 prefix.
(REX2_M): Extend for gpr32.
(PREFIX_REX2): Ditto.
(PREFIX_REX2_ILLEGAL): Ditto.
(ckprefix): Ditto.
(prefix_name): Ditto.
(print_insn): Ditto.
(print_register): Ditto.
(OP_E_memory): Ditto.
(OP_REG): Ditto.
(OP_EX): Ditto.
* i386-gen.c (rex2_disallowed): Some instructions are not allowed rex2 prefix.
(process_i386_opcode_modifier): Set NoEgpr for VEX and some special instructions.
(output_i386_opcode): Handle if_entry_needs_special_handle.
* i386-init.h : Regenerated.
* i386-mnem.h : Regenerated.
* i386-opc.h (enum i386_cpu): Add CpuAPX_F.
(NoEgpr): New.
(Prefix_NoOptimize): Ditto.
(Prefix_REX2): Ditto.
(RegRex2): Ditto.
* i386-opc.tbl: Add rex2 prefix.
* i386-reg.tbl: Add egprs (r16-r31).
* i386-tbl.h: Regenerated.
|
|
The pcalau12i + addi.d of TLS LD/GD/DESC relax to pcaddi.
Relaxation is only performed when the TLS model transition is not possible.
|
|
Transitions between DESC->IE/LE and IE->LE are supported now.
1. For DESC -> LE:
pcalau12i $a0,%desc_pc_hi20(var) => lu12i.w $a0,%le_hi20(var)
addi.d $a0,$a0,%desc_pc_lo12(var) => ori $a0,$a0,%le_lo12(var)
ld.d $a1,$a0,%desc_ld(var) => NOP
jirl $ra,$a1,%desc_call(var) => NOP
add.d $a0,$a0,$tp
2. For DESC -> IE:
pcalau12i $a0,%desc_pc_hi20(var) => pcalau12i $a0,%ie_pc_hi20(var)
addi.d $a0,$a0,%desc_pc_lo12(var) => ld.d $a0,$a0,%ie_pc_lo12(var)
ld.d $a1,$a0,%desc_ld(var) => NOP
jirl $ra,$a1,%desc_call(var) => NOP
add.d $a0,$a0,$tp
3. For IE -> LE:
pcalau12i $a0,%ie_pc_hi20(var) => lu12i.w $a0,%le_hi20(var)
ld.d $a0,$a0,%ie_pc_lo12(var) => ori $a0,$a0,%le_lo12(var)
add.d $a0,$a0,$tp
4. When a tls variable is accessed using both DESC and IE, DESC transitions
to IE and uses the same GOT entry as IE.
|
|
The normal DESC instruction sequence is:
pcalau12i $a0,%desc_pc_hi20(var) #R_LARCH_TLS_DESC_PC_HI20
addi.d $a0,$a0,%desc_pc_lo12(var) #R_LARCH_TLS_DESC_PC_LO12
ld.d $ra,$a0,%desc_ld(var) #R_LARCH_TLS_DESC_LD
jirl $ra,$ra,%desc_call(var) #R_LARCH_TLS_DESC_CALL
add.d $a0,$a0,$tp
|
|
Print instruction description as comment in disassembly with s390
architecture specific option "insndesc":
- For objdump it can be enabled with option "-M insndesc"
- In gdb it can be enabled with "set disassembler-options insndesc"
Since comments are not column aligned the output can enhanced for
readability by postprocessing using a filter such as "expand":
... | expand -t 8,16,24,32,40,80
Or when using in combination with objdump option --visualize-jumps:
... | expand | sed -e 's/ *#/\t#/' | expand -t 1,80
Note that the instruction descriptions add about 128 KB to s390-opc.o:
s390-opc.o without instruction descriptions: 216368 bytes
s390-opc.o with instruction descriptions : 348432 bytes
binutils/
* NEWS: Mention new s390-specific disassembler option
"insndesc".
include/
* opcode/s390.h (struct s390_opcode): Add field to hold
instruction description.
opcodes/
* s390-mkopc.c: Copy instruction description from s390-opc.txt
into generated operation code table s390-opc.tab.
* s390-opc.c (s390_opformats): Provide NULL as description in
.insn pseudo-mnemonics opcode table.
* s390-dis.c: Add s390-specific disassembler option "insndesc"
and optionally print the instruction description as comment in
the disassembly when it is specified.
gas/
* testsuite/gas/s390/s390.exp: Add new test disassembly test
case "zarch-insndesc".
* testsuite/gas/s390/zarch-insndesc.s: New test case for s390-
specific disassembler option "insndesc".
* testsuite/gas/s390/zarch-insndesc.d: Likewise.
Signed-off-by: Jens Remus <jremus@linux.ibm.com>
Reviewed-by: Andreas Krebbel <krebbel@linux.ibm.com>
|
|
This patch add support for FEAT_ITE "Instrumentation Extension" adding
the "trcit" instruction.
This is enabled by the +ite march flag.
|
|
This patch add supports for FEAT_SPECRES2 "Enhanced speculation
restriction instructions" adding the "cosp" instruction.
This is mandatory v8.9-a/v9.4-a and optional v8.0-a+/v9.0-a+. It is
enabled by the +predres2 march flag.
|
|
R_LARCH_CALL36 is used for medium code model function call pcaddu18i+jirl, and
these two instructions must adjacent.
The LoongArch ABI v2.20 at here: https://github.com/loongson/la-abi-specs.
|
|
The description of instructions 'th.fmv.hw.x' and 'th.fmv.x.hw' of the
XTheadFmv extension in T-Head specific is incorrect, and it also has
some impact on the implementation of the binutils, so this patch
corrects this.
For details see:
https://github.com/T-head-Semi/thead-extension-spec/pull/34
gas/ChangeLog:
* testsuite/gas/riscv/x-thead-fmv.d: Correct test.
* testsuite/gas/riscv/x-thead-fmv.s: Likewise.
include/ChangeLog:
* opcode/riscv-opc.h (MATCH_TH_FMV_HW_X): Correct coding.
(MASK_TH_FMV_HW_X): Likewise.
(MATCH_TH_FMV_X_HW): Likewise.
(MASK_TH_FMV_X_HW): Likewise.
opcodes/ChangeLog:
* riscv-opc.c: Correct operands.
|
|
I've reimplemented the .debug_names code in GDB -- it was quite far
from being correct, and the new implementation is much closer to what
is specified by DWARF.
However, the new writer in GDB needs to emit some symbol properties,
so that the reader can be fully functional. This patch adds a few new
DW_IDX_* constants, and tries to document the existing extensions as
well. (My patch series add more documentation of these to the GDB
manual as well.)
2023-12-10 Tom Tromey <tom@tromey.com>
* dwarf2.def (DW_IDX_GNU_internal, DW_IDX_GNU_external): Comment.
(DW_IDX_GNU_main, DW_IDX_GNU_language, DW_IDX_GNU_linkage_name):
New constants.
|
|
This adds a new PEI target pei-riscv64-little. Only objdump and objcopy
are supported.
bfd:
* .gitignore: Add pe-riscv64igen.c.
* Makefile.am (BFD64_BACKENDS): Add pei-riscv64.lo,
pe-riscv64igen.lo.
(BFD64_BACKENDS_CFILES): Add pei-riscv64.c.
(BUILD_CFILES): Add pe-riscv64igen.c.
(pe-riscv64igen.c): New rule.
* Makefile.in: Regenerate.
* bfd.c (bfd_get_sign_extend_vma): Add pei-riscv64-little.
* coff-riscv64.c: New file.
* coffcode.h (coff_set_arch_mach_hook, coff_set_flags)
(coff_write_object_contents): Add riscv64 (riscv64_pei_vec)
support.
* config.bfd (targ_selvecs): Add riscv64_pei_vec to all riscv*
targets.
* configure.ac: Handle riscv64_pei_vec.
* configure: Regenerate.
* libpei.h (GET_OPTHDR_IMAGE_BASE, PUT_OPTHDR_IMAGE_BASE)
(GET_OPTHDR_SIZE_OF_STACK_RESERVE)
(PUT_OPTHDR_SIZE_OF_STACK_RESERVE)
(GET_OPTHDR_SIZE_OF_STACK_COMMIT, PUT_OPTHDR_SIZE_OF_STACK_COMMIT)
(GET_OPTHDR_SIZE_OF_HEAP_RESERVE, PUT_OPTHDR_SIZE_OF_HEAP_RESERVE)
(GET_OPTHDR_SIZE_OF_HEAP_COMMIT, PUT_OPTHDR_SIZE_OF_HEAP_COMMIT)
(GET_PDATA_ENTRY, _bfd_XX_bfd_copy_private_bfd_data_common)
(_bfd_XX_bfd_copy_private_section_data)
(_bfd_XX_get_symbol_info, _bfd_XX_only_swap_filehdr_out)
(_bfd_XX_print_private_bfd_data_common)
(_bfd_XXi_final_link_postscript, _bfd_XXi_only_swap_filehdr_out)
(_bfd_XXi_swap_aouthdr_in, _bfd_XXi_swap_aouthdr_out)
(_bfd_XXi_swap_aux_in, _bfd_XXi_swap_aux_out)
(_bfd_XXi_swap_lineno_in, _bfd_XXi_swap_lineno_out)
(_bfd_XXi_swap_scnhdr_out, _bfd_XXi_swap_sym_in)
(_bfd_XXi_swap_sym_out, _bfd_XXi_swap_debugdir_in)
(_bfd_XXi_swap_debugdir_out, _bfd_XXi_write_codeview_record)
(_bfd_XXi_slurp_codeview_record) [COFF_WITH_peRiscV64]: Define.
(_bfd_peRiscV64_print_ce_compressed_pdata): Declare.
* peXXigen.c (_bfd_XXi_swap_aouthdr_in, _bfd_XXi_swap_aouthdr_out)
(_bfd_XXi_swap_scnhdr_out, pe_print_pdata)
(_bfd_XX_print_private_bfd_data_common)
(_bfd_XX_bfd_copy_private_section_data)
(_bfd_XXi_final_link_postscript): Support COFF_WITH_peRiscV64.
* pei-riscv64.c: New file.
* peicode.h (coff_swap_scnhdr_in, pe_ILF_build_a_bfd)
(pe_ILF_object_p): Support COFF_WITH_peRiscV64.
(jtab): Add dummy entry that traps.
* targets.c (_bfd_target_vector): Add riscv64_pei_vec.
binutils:
* testsuite/binutils-all/riscv/pei-riscv64.d: New.
* testsuite/binutils-all/riscv/pei-riscv64.s: New.
include:
* coff/riscv64.h: New file.
* coff/pe.h (IMAGE_FILE_MACHINE_RISCV32)
(IMAGE_FILE_MACHINE_RISCV64): Define.
|
|
Add support for jump visualization for the s390 architecture in
disassembly:
objdump -d --visualize-jumps ...
Annotate the (conditional) jump and branch relative instructions with
information required for jump visualization:
- jump: Unconditional jump / branch relative.
- condjump: Conditional jump / branch relative.
- jumpsr: Jump / branch relative to subroutine.
Unconditional jump and branch relative instructions are annotated as
jump.
Conditional jump and branch relative instructions, jump / branch
relative on count/index, and compare and jump / branch relative
instructions are annotated as condjump.
Jump and save (jas, jasl) and branch relative and save (bras, brasl)
instructions are annotated as jumpsr (jump to subroutine).
Provide instruction information required for jump visualization during
disassembly.
The instruction type is provided after determining the opcode.
For non-code it is set to dis_noninsn. Otherwise it defaults to
dis_nonbranch. No annotation is done for data reference instructions
(i.e. instruction types dis_dref and dis_dref2). Note that the
instruction type needs to be provided before printing of the
instruction, as it is used in print_address_func() to translate the
argument value into an address if it is assumed to be a PC-relative
offset. Note that this is never the case on s390, as
print_address_func() is only called with addresses and never with
offsets.
The target of the (conditional) jump and branch relative instructions
is provided during print, when the PC relative operand is decoded.
include/
* opcode/s390.h: Define opcode flags to annotate instruction
class information for jump visualization:
S390_INSTR_FLAG_CLASS_BRANCH, S390_INSTR_FLAG_CLASS_RELATIVE,
S390_INSTR_FLAG_CLASS_CONDITIONAL, and
S390_INSTR_FLAG_CLASS_SUBROUTINE.
Define opcode flags mask S390_INSTR_FLAG_CLASS_MASK for above
instruction class information.
Define helpers for common instruction class flag combinations:
S390_INSTR_FLAGS_CLASS_JUMP, S390_INSTR_FLAGS_CLASS_CONDJUMP,
and S390_INSTR_FLAGS_CLASS_JUMPSR.
opcodes/
* s390-mkopc.c: Add opcode flags to annotate information
for jump visualization: jump, condjump, and jumpsr.
* s390-opc.txt: Annotate (conditional) jump and branch relative
instructions with information for jump visualization.
* s390-dis.c (print_insn_s390, s390_print_insn_with_opcode):
Provide instruction information for jump visualization.
Signed-off-by: Jens Remus <jremus@linux.ibm.com>
Reviewed-by: Andreas Krebbel <krebbel@linux.ibm.com>
|
|
SiFive has define as set of flexible instruction for extending vector
coprocessor, it able to encoding opcode like .insn but with predefined
format.
List of instructions:
sf.vc.x
sf.vc.i
sf.vc.vv
sf.vc.xv
sf.vc.iv
sf.vc.fv
sf.vc.vvv
sf.vc.xvv
sf.vc.ivv
sf.vc.fvv
sf.vc.vvw
sf.vc.xvw
sf.vc.ivw
sf.vc.fvw
sf.vc.v.x
sf.vc.v.i
sf.vc.v.vv
sf.vc.v.xv
sf.vc.v.iv
sf.vc.v.fv
sf.vc.v.vvv
sf.vc.v.xvv
sf.vc.v.ivv
sf.vc.v.fvv
sf.vc.v.vvw
sf.vc.v.xvw
sf.vc.v.ivw
sf.vc.v.fvw
Spec of Xsfvcp
https://www.sifive.com/document-file/sifive-vector-coprocessor-interface-vcix-software
Co-authored-by: Hau Hsu <hau.hsu@sifive.com>
Co-authored-by: Kito Cheng <kito.cheng@sifive.com>
|
|
Back then when the support for the RISC-V vector crypto extensions
was merged, the specification was frozen, but not ratified.
A frozen specification is allowed to change within tight bounds
before ratification and this has happend with the vector crypto
extensions.
The following changes were applied:
* A new extension Zvkb was defined, which is a strict subset of Zvbb.
* Zvkn and Zvks include now Zvkb instead of Zvbb.
This patch implements these changes between the frozen and the
ratified specification.
Note, that this technically an incompatible change of Zvkn and Zvks,
but I am not aware of any project that depends on the currently
implemented behaviour of Zvkn and Zvks. So this patch should be fine.
Reported-By: Jerry Shih <jerry.shih@sifive.com>
Reported-By: Eric Biggers <ebiggers@kernel.org>
Signed-off-by: Christoph Müllner <christoph.muellner@vrull.eu>
|
|
The following patch attempts to use x86 SHA ISA if available to speed
up in my testing about 2.5x sha1 build-id processing (in my case on
AMD Ryzen 5 3600) while producing the same result.
I believe AArch64 has similar HW acceleration for SHA1, perhaps it
could be added similarly.
Note, seems lld uses BLAKE3 rather than md5/sha1. I think it would be
a bad idea to lie to users, if they choose --buildid=sha1, we should
be using SHA1, not some other checksum, but perhaps we could add some other
--buildid= styles and perhaps make one of the new the default.
Tested on x86_64-linux, both on Intel i9-7960X (which doesn't have
sha_ni ISA support) without/with the patch and on AMD Ryzen 5 3600
(which does have it) without/with the patch.
2023-11-28 Jakub Jelinek <jakub@redhat.com>
include/
* sha1.h (sha1_process_bytes_fn): New typedef.
(sha1_choose_process_bytes): Declare.
libiberty/
* configure.ac (HAVE_X86_SHA1_HW_SUPPORT): New check.
* sha1.c: If HAVE_X86_SHA1_HW_SUPPORT is defined, include x86intrin.h
and cpuid.h.
(sha1_hw_process_bytes, sha1_hw_process_block,
sha1_choose_process_bytes): New functions.
* config.in: Regenerated.
* configure: Regenerated.
ld/
* ldbuildid.c (generate_build_id): Use sha1_choose_process_bytes ()
instead of &sha1_process_bytes.
|
|
Fold M_{S,Z}EXTH, deriving signed-ness from the incoming mnemonic. Fold
riscv_ext()'s calls md_assemblef(), the first of which were entirely
identical, while the other pair differed in just a single character.
Acked-by: Palmer Dabbelt <palmer@rivosinc.com>
|
|
T-Head has a range of vendor-specific instructions. Therefore
it makes sense to group them into smaller chunks in form of
vendor extensions.
This patch adds permutation instructions for the "XTheadVector"
extension. The 'th' prefix and the "XTheadVector" extension
are documented in a PR for the RISC-V toolchain conventions ([1]).
[1] https://github.com/riscv-non-isa/riscv-toolchain-conventions/pull/19
Co-developed-by: Lifang Xia <lifang_xia@linux.alibaba.com>
Co-developed-by: Christoph Müllner <christoph.muellner@vrull.eu>
gas/ChangeLog:
* testsuite/gas/riscv/x-thead-vector.d: Add tests for
permutation instructions.
* testsuite/gas/riscv/x-thead-vector.s: Likewise.
include/ChangeLog:
* opcode/riscv-opc.h (MATCH_TH_VMVXS): New.
opcodes/ChangeLog:
* riscv-opc.c: Likewise.
|
|
T-Head has a range of vendor-specific instructions. Therefore
it makes sense to group them into smaller chunks in form of
vendor extensions.
This patch adds mask instructions for the "XTheadVector"
extension. The 'th' prefix and the "XTheadVector" extension
are documented in a PR for the RISC-V toolchain conventions ([1]).
[1] https://github.com/riscv-non-isa/riscv-toolchain-conventions/pull/19
Co-developed-by: Lifang Xia <lifang_xia@linux.alibaba.com>
Co-developed-by: Christoph Müllner <christoph.muellner@vrull.eu>
gas/ChangeLog:
* testsuite/gas/riscv/x-thead-vector.d: Add tests for
mask instructions.
* testsuite/gas/riscv/x-thead-vector.s: Likewise.
include/ChangeLog:
* opcode/riscv-opc.h (MATCH_TH_VMPOPCM): New.
opcodes/ChangeLog:
* riscv-opc.c: Likewise.
|
|
extension
T-Head has a range of vendor-specific instructions. Therefore
it makes sense to group them into smaller chunks in form of
vendor extensions.
This patch adds floating-point arithmetic instructions for the
"XTheadVector" extension. The 'th' prefix and the
"XTheadVector" extension are documented in a PR for the
RISC-V toolchain conventions ([1]).
[1] https://github.com/riscv-non-isa/riscv-toolchain-conventions/pull/19
Co-developed-by: Lifang Xia <lifang_xia@linux.alibaba.com>
Co-developed-by: Christoph Müllner <christoph.muellner@vrull.eu>
gas/ChangeLog:
* testsuite/gas/riscv/x-thead-vector.d: Add tests for
floating-point arithmetic instructions.
* testsuite/gas/riscv/x-thead-vector.s: Likewise.
include/ChangeLog:
* opcode/riscv-opc.h (MATCH_TH_VFSQRTV): New.
opcodes/ChangeLog:
* riscv-opc.c: Likewise.
|
|
extension
T-Head has a range of vendor-specific instructions. Therefore
it makes sense to group them into smaller chunks in form of
vendor extensions.
This patch adds fixed-point arithmetic instructions for the
"XTheadVector" extension. The 'th' prefix and the
"XTheadVector" extension are documented in a PR for the
RISC-V toolchain conventions ([1]).
[1] https://github.com/riscv-non-isa/riscv-toolchain-conventions/pull/19
Co-developed-by: Lifang Xia <lifang_xia@linux.alibaba.com>
Co-developed-by: Christoph Müllner <christoph.muellner@vrull.eu>
gas/ChangeLog:
* testsuite/gas/riscv/x-thead-vector.d: Add tests for
fixed-point arithmetic instructions.
* testsuite/gas/riscv/x-thead-vector.s: Likewise.
include/ChangeLog:
* opcode/riscv-opc.h (MATCH_TH_VAADDVV): New.
opcodes/ChangeLog:
* riscv-opc.c: Likewise.
|
|
T-Head has a range of vendor-specific instructions. Therefore
it makes sense to group them into smaller chunks in form of
vendor extensions.
This patch adds integer arithmetic instructions for the
"XTheadVector" extension. The 'th' prefix and the
"XTheadVector" extension are documented in a PR for the
RISC-V toolchain conventions ([1]).
[1] https://github.com/riscv-non-isa/riscv-toolchain-conventions/pull/19
Co-developed-by: Lifang Xia <lifang_xia@linux.alibaba.com>
Co-developed-by: Christoph Müllner <christoph.muellner@vrull.eu>
gas/ChangeLog:
* testsuite/gas/riscv/x-thead-vector.d: Add tests for
integer arithmetic instructions.
* testsuite/gas/riscv/x-thead-vector.s: Likewise.
include/ChangeLog:
* opcode/riscv-opc.h (MATCH_TH_VADCVVM): New.
opcodes/ChangeLog:
* riscv-opc.c: Likewise.
|
|
T-Head has a range of vendor-specific instructions. Therefore
it makes sense to group them into smaller chunks in form of
vendor extensions.
This patch adds the sub-extension "XTheadZvamo" for the
"XTheadVector" extension, and it provides AMO instructions
for T-Head VECTOR vendor extension. The 'th' prefix and the
"XTheadVector" extension are documented in a PR for the
RISC-V toolchain conventions ([1]).
[1] https://github.com/riscv-non-isa/riscv-toolchain-conventions/pull/19
Co-developed-by: Lifang Xia <lifang_xia@linux.alibaba.com>
Co-developed-by: Christoph Müllner <christoph.muellner@vrull.eu>
bfd/ChangeLog:
* elfxx-riscv.c (riscv_multi_subset_supports): Add support
for "XTheadZvamo" extension.
(riscv_multi_subset_supports_ext): Likewise.
gas/ChangeLog:
* doc/c-riscv.texi:
* testsuite/gas/riscv/x-thead-vector-zvamo.d: New test.
* testsuite/gas/riscv/x-thead-vector-zvamo.s: New test.
include/ChangeLog:
* opcode/riscv-opc.h (MATCH_TH_VAMOADDWV): New.
* opcode/riscv.h (enum riscv_insn_class): Add insn class.
opcodes/ChangeLog:
* riscv-opc.c: Likewise.
|
|
T-Head has a range of vendor-specific instructions. Therefore it
makes sense to group them into smaller chunks in form of vendor
extensions.
This patch adds provides load/store segment instructions for T-Head VECTOR
vendor extension, which same as the "Zvlsseg" extension in RVI 0.71 vector
extension, but belongs to the "XTheadVector" extension. The 'th' prefix
and the "XTheadVector" extension are documented in a PR for the
RISC-V toolchain conventions ([1]).
[1] https://github.com/riscv-non-isa/riscv-toolchain-conventions/pull/19
Co-developed-by: Lifang Xia <lifang_xia@linux.alibaba.com>
Co-developed-by: Christoph Müllner <christoph.muellner@vrull.eu>
gas/ChangeLog:
* testsuite/gas/riscv/x-thead-vector.d: Add test.
* testsuite/gas/riscv/x-thead-vector.s: Likewise.
include/ChangeLog:
* opcode/riscv-opc.h (MATCH_TH_VLSEG2BV): New.
opcodes/ChangeLog:
* riscv-opc.c: Likewise.
|
|
T-Head has a range of vendor-specific instructions. Therefore
it makes sense to group them into smaller chunks in form of
vendor extensions.
This patch adds load/store instructions for the "XTheadVector"
extension. The 'th' prefix and the "XTheadVector" extension are
documented in a PR for the RISC-V toolchain conventions ([1]).
[1] https://github.com/riscv-non-isa/riscv-toolchain-conventions/pull/19
Co-developed-by: Lifang Xia <lifang_xia@linux.alibaba.com>
Co-developed-by: Christoph Müllner <christoph.muellner@vrull.eu>
gas/ChangeLog:
* testsuite/gas/riscv/x-thead-vector.d: Add tests for
load/store instructions.
* testsuite/gas/riscv/x-thead-vector.s: Likewise.
include/ChangeLog:
* opcode/riscv-opc.h (MATCH_TH_VLBV): New.
opcodes/ChangeLog:
* riscv-opc.c: Likewise.
|
|
T-Head has a range of vendor-specific instructions.
Therefore it makes sense to group them into smaller chunks
in form of vendor extensions.
This patch adds the CSRs for XTheadVector. Because of the
conflict between encoding and teh 'V' extension, it is implemented
by alias. The 'th' prefix and the "XTheadVector" extension are
documented in a PR for the RISC-V toolchain conventions ([1]).
[1] https://github.com/riscv-non-isa/riscv-toolchain-conventions/pull/19
Co-developed-by: Lifang Xia <lifang_xia@linux.alibaba.com>
Co-developed-by: Christoph Müllner <christoph.muellner@vrull.eu>
gas/ChangeLog:
* config/tc-riscv.c (enum riscv_csr_class): Add the class for
the CSRs of the "XTheadVector" extension.
(riscv_csr_address): Likewise.
* testsuite/gas/riscv/x-thead-vector-csr-warn.d: New test.
* testsuite/gas/riscv/x-thead-vector-csr-warn.l: New test.
* testsuite/gas/riscv/x-thead-vector-csr.d: New test.
* testsuite/gas/riscv/x-thead-vector-csr.s: New test.
include/ChangeLog:
* opcode/riscv-opc.h (DECLARE_CSR_ALIAS): Likewise.
opcodes/ChangeLog:
* riscv-dis.c (print_insn_args): Prefix the CSRs disassembly with 'th'.
|
|
T-Head has a range of vendor-specific instructions ([2]).
Therefore it makes sense to group them into smaller chunks
in form of vendor extensions.
This patch adds the "XTheadVector" extension, a collection of
T-Head-specific vector instructions. The 'th' prefix and the
"XTheadVector" extension are documented in a PR for the RISC-V
toolchain conventions ([1]).
Here are some things that need to be explained:
The "XTheadVector" extension is not a custom-extension, but
a non-standard non-conforming extension. The encoding space
of the "TheadVector" instructions overlaps with those of
the 'V' extension. This encoding space conflict is not on
purpose, but the result of issues in the past that have
been resolved since. Therefore, the "XTheadVector" extension
and the 'V' extension are in conflict.
[1] https://github.com/riscv-non-isa/riscv-toolchain-conventions/pull/19
[2] https://github.com/T-head-Semi/thead-extension-spec/releases/download/2.3.0/xthead-2023-11-10-2.3.0.pdf
Co-developed-by: Lifang Xia <lifang_xia@linux.alibaba.com>
Co-developed-by: Christoph Müllner <christoph.muellner@vrull.eu>
bfd/ChangeLog:
* elfxx-riscv.c (riscv_parse_check_conflicts): The
"XTheadVector" extension and the 'V' extension are in conflict.
(riscv_multi_subset_supports): Likewise..
(riscv_multi_subset_supports_ext): Likewise.
gas/ChangeLog:
* doc/c-riscv.texi:
* testsuite/gas/riscv/x-thead-vector-fail.d: New test.
* testsuite/gas/riscv/x-thead-vector-fail.l: New test.
* testsuite/gas/riscv/x-thead-vector.s: New test.
include/ChangeLog:
* opcode/riscv.h (enum riscv_insn_class):
|
|
This patch adds the permission model enhancement and memory
attribute index enhancement features and their corresponding
system registers in AArch64 assembler.
Permission Indirection Extension (FEAT_S1PIE, FEAT_S2PIE)
Permission Overlay Extension (FEAT_S1POE, FEAT_S2POE)
Memory Attribute Index Enhancement (FEAT_AIE)
Extension to Translation Control Registers (FEAT_TCR2)
These features are available by default from Armv9.4-A architecture.
|
|
This patch adds 3 new AT system instructions through FEAT_ATS1A
feature, which are available by default from Armv9.4-A architecture.
|
|
This patch also adds support for:
1. FEAT_RASv2 feature and "ERXGSR_EL1" system register.
RASv2 feature is enabled by passing +rasv2 to -march
(eg: -march=armv8-a+rasv2).
2. FEAT_SCTLR2 and following system registers.
SCTLR2_EL1, SCTLR2_EL12, SCTLR2_EL2 and SCTLR2_EL3.
3. FEAT_FGT2 and following system registers.
HDFGRTR2_EL2, HDFGWTR2_EL2, HFGRTR2_EL2, HFGWTR2_EL2
4. FEAT_PFAR and following system registers.
PFAR_EL1, PFAR_EL2 and PFAR_EL12.
FEAT_RASv2, FEAT_SCTLR2, FEAT_FGT2 and FEAT_PFAR features are by default
enabled from Armv9.4-A architecture.
This patch also adds support for two read only system registers
id_aa64mmfr3_el1 and id_aa64mmfr4_el1, which are available from
Armv8-A Architecture.
|
|
This patch adds features to the Statistical Profiling Extension,
identified as FEAT_SPEv1p4, FEAT_SPE_FDS, and FEAT_SPE_CRR, which
are enabled by default from Armv9.4-A.
Also adds support for system register "pmsdsfr_el1".
|
|
Teach bfd and readelf about some recent gfx11 architectures. This code
is taken from the rocgdb 5.7.x branch [1].
[1] https://github.com/rocm-Developer-Tools/rocgdb/tree/rocm-5.7.x
bfd/ChangeLog:
* archures.c (bfd_mach_amdgcn_gfx1100, bfd_mach_amdgcn_gfx1101,
bfd_mach_amdgcn_gfx1102): New.
* bfd-in2.h (bfd_mach_amdgcn_gfx1100, bfd_mach_amdgcn_gfx1101,
bfd_mach_amdgcn_gfx1102): New.
* cpu-amdgcn.c (arch_info_struct): Add entries for
bfd_mach_amdgcn_gfx1100, bfd_mach_amdgcn_gfx1101,
bfd_mach_amdgcn_gfx1102.
binutils/ChangeLog:
* readelf.c (decode_AMDGPU_machine_flags): Handle gfx1100,
gfx1101, gfx1102.
include/ChangeLog:
* elf/amdgpu.h (EF_AMDGPU_MACH_AMDGCN_GFX1100,
EF_AMDGPU_MACH_AMDGCN_GFX1101,
EF_AMDGPU_MACH_AMDGCN_GFX1102): New.
Change-Id: I95a8a62942e359781a1c9fa2079950fbcf2a78b8
Co-Authored-By: Laurent Morichetti <laurent.morichetti@amd.com>
Cc: Lancelot Six <lancelot.six@amd.com>
|
|
|
|
executable stacks and/or executable segments.
include
* bfdlink.h (struct bfd_link_info): Update descriptions of the 'execstack', 'noexecstack' and 'warn_execstack' fields. Add 'error_exectack' and 'warn_is_error_for_rwx_segments' fields.
bfd
* elf.c (assign_file_positions_except_relocs): Turn warnings about executable segments into errors if so requested.
* elflink.c (bfd_elf_size_dynamic_sections): Turn warnings about executable stacks into errors if so requested.
ld
* ldlex.h (enum option_values): Add OPTION_ERROR_EXECSTACK, OPTION_NO_ERROR_EXECSTACK, OPTION_WARN_EXECSTACK_OBJECTS, OPTION_ERROR_RWX_SEGMENTS and OPTION_NO_ERROR_RWX_SEGMENTS. (struct ld_option): Add new long options. (parse_args): Parse new long options. (elf_static_list_options): Display the new options.
* ld.texi: Document the new command line options.
* configure.ac (error-execstack): New configuration option. (error-rwx-segments): New configuration option.
* emultempl/elf.em (_before_parse): Initialse the new linkinfo fields.
* NEWS: Mention the new features.
* config.in: Regenerate.
* configure: Regenerate.
* testsuite/ld-elf/commonpage2.d: Disable errors for RWX segments and/or executable stacks.
* testsuite/ld-elf/elf.exp: Likewise.
* testsuite/ld-elf/header.d: Likewise.
* testsuite/ld-elf/loadaddr1.d: Likewise.
* testsuite/ld-elf/loadaddr2.d: Likewise.
* testsuite/ld-elf/maxpage4.d: Likewise.
* testsuite/ld-elf/nobits-1.d: Likewise.
* testsuite/ld-elf/note-1.d: Likewise.
* testsuite/ld-elf/orphan-10.d: Likewise.
* testsuite/ld-elf/orphan-11.d: Likewise.
* testsuite/ld-elf/orphan-12.d: Likewise.
* testsuite/ld-elf/orphan-5.d: Likewise.
* testsuite/ld-elf/orphan-7.d: Likewise.
* testsuite/ld-elf/orphan-8.d: Likewise.
* testsuite/ld-elf/orphan-9.d: Likewise.
* testsuite/ld-elf/orphan-region.d: Likewise.
* testsuite/ld-elf/orphan.d: Likewise.
* testsuite/ld-elf/pr19539.d: Likewise.
* testsuite/ld-elf/pr26256-1a.d: Likewise.
* testsuite/ld-elf/pr26907.d: Likewise.
* testsuite/ld-elf/pr28597.d: Likewise.
* testsuite/ld-elf/retain2.d: Likewise.
* testsuite/ld-elf/shared.exp: Likewise.
* testsuite/ld-elf/size-1.d: Likewise.
* testsuite/ld-elf/textaddr7.d: Likewise.
* testsuite/ld-elf/warn1.d: Likewise.
* testsuite/ld-elf/warn2.d: Likewise.
* testsuite/ld-i386/discarded1.d: Likewise.
* testsuite/ld-i386/pr19175.d: Likewise.
* testsuite/ld-i386/pr19539.d: Likewise.
* testsuite/ld-i386/pr23189.d: Likewise.
* testsuite/ld-plugin/lto-3r.d: Likewise.
* testsuite/ld-plugin/lto-5r.d: Likewise.
* testsuite/ld-plugin/lto.exp: Likewise.
* testsuite/ld-powerpc/ppc476-shared.d: Likewise.
* testsuite/ld-powerpc/ppc476-shared2.d: Likewise.
* testsuite/ld-powerpc/pr28827-2.d: Likewise.
* testsuite/ld-s390/s390.exp: Likewise.
* testsuite/ld-scripts/align2a.d: Likewise.
* testsuite/ld-scripts/align2b.d: Likewise.
* testsuite/ld-scripts/align5.d: Likewise.
* testsuite/ld-scripts/alignof.exp: Likewise.
* testsuite/ld-scripts/crossref.exp: Likewise.
* testsuite/ld-scripts/defined2.d: Likewise.
* testsuite/ld-scripts/defined3.d: Likewise.
* testsuite/ld-scripts/defined5.d: Likewise.
* testsuite/ld-scripts/pr14962.d: Likewise.
* testsuite/ld-scripts/pr18963.d: Likewise.
* testsuite/ld-scripts/pr20302.d: Likewise.
* testsuite/ld-scripts/print-memory-usage.exp: Likewise.
* testsuite/ld-scripts/rgn-at1.d: Likewise.
* testsuite/ld-scripts/rgn-at10.d: Likewise.
* testsuite/ld-scripts/rgn-at4.d: Likewise.
* testsuite/ld-scripts/rgn-at6.d: Likewise.
* testsuite/ld-scripts/rgn-at8.d: Likewise.
* testsuite/ld-scripts/rgn-at9.d: Likewise.
* testsuite/ld-scripts/rgn-over1.d: Likewise.
* testsuite/ld-scripts/rgn-over2.d: Likewise.
* testsuite/ld-scripts/rgn-over4.d: Likewise.
* testsuite/ld-scripts/rgn-over5.d: Likewise.
* testsuite/ld-scripts/rgn-over6.d: Likewise.
* testsuite/ld-scripts/script.exp: Likewise.
* testsuite/ld-scripts/sizeof.exp: Likewise.
* testsuite/ld-scripts/sort-file.d: Likewise.
* testsuite/ld-x86-64/discarded1.d: Likewise.
* testsuite/ld-x86-64/pr19175.d: Likewise.
* testsuite/ld-x86-64/pr19539a.d: Likewise.
* testsuite/ld-x86-64/pr19539b.d: Likewise.
* testsuite/ld-x86-64/pr23189.d: Likewise.
|
|
|
|
Enable the `+lse128' feature modifier which, together with new
internal feature flags, enables LSE128 instructions, which are
represented via the new `_LSE128_INSN' macro.
gas/ChangeLog:
* config/tc-aarch64.c (aarch64_features): Add new "lse128"
entry.
include/ChangeLog:
* include/opcode/aarch64.h (enum aarch64_feature_bit): New
AARCH64_FEATURE_LSE128 feature bit.
(enum aarch64_insn_class): New lse128_atomic instruction class.
opcodes/ChangeLog:
* opcodes/aarch64-tbl.h (aarch64_feature_lse128): New.
(LSE128): Likewise.
(_LSE128_INSN): Likewise.
|
|
Given the particular encoding of the LSE128 instructions, create the
necessary shared input+output operand register description and
handling in the code to allow for the encoding of the LSE128 128-bit
atomic operations.
gas/ChangeLog:
* config/tc-aarch64.c (parse_operands):
include/ChangeLog:
* opcode/aarch64.h (enum aarch64_opnd):
opcodes/ChangeLog:
* aarch64-opc.c (fields):
(aarch64_print_operand):
* aarch64-opc.h (enum aarch64_field_kind):
* aarch64-tbl.h (AARCH64_OPERANDS):
|
|
Add Binutils support for system registers associated with the
Translation Hardening Extension (THE).
In doing so, we also add core feature support for THE, enabling its
associated feature flag and implementing the necessary
feature-checking machinery.
Regression tested on aarch64-linux-gnu, no regressions.
gas/ChangeLog:
* config/tc-aarch64.c (aarch64_features): Add "+the" feature modifier.
* doc/c-aarch64.texi (AArch64 Extensions): Update
documentation for `the' option.
* testsuite/gas/aarch64/sysreg-8.s: Add tests for `the'
associated system registers.
* testsuite/gas/aarch64/sysreg-8.d: Likewise.
include/ChangeLog:
* opcode/aarch64.h (enum aarch64_feature_bit): Add
AARCH64_FEATURE_THE.
opcode/ChangeLog:
* aarch64-opc.c (aarch64_sys_ins_reg_supported_p): Add `the'
system register check support.
* aarch64-sys-regs.def: Add `rcwmask_el1' and `rcwsmask_el1'
* aarch64-tbl.h: Define `THE' preprocessor macro.
|
|
Spec: https://docs.openhwgroup.org/projects/cv32e40p-user-manual/en/latest/instruction_set_extensions.html
Contributors:
Mary Bennett <mary.bennett@embecosm.com>
Nandni Jamnadas <nandni.jamnadas@embecosm.com>
Pietra Ferreira <pietra.ferreira@embecosm.com>
Charlie Keaney
Jessica Mills
Craig Blackmore <craig.blackmore@embecosm.com>
Simon Cook <simon.cook@embecosm.com>
Jeremy Bennett <jeremy.bennett@embecosm.com>
Helene Chelin <helene.chelin@embecosm.com>
bfd/ChangeLog:
* elfxx-riscv.c (riscv_multi_subset_supports): Added `xcvalu`
instruction class.
(riscv_multi_subset_supports_ext): Likewise.
gas/ChangeLog:
* config/tc-riscv.c (validate_riscv_insn): Added the necessary
operands for the extension.
(riscv_ip): Likewise.
* doc/c-riscv.texi: Noted XCValu as an additional ISA extension
for CORE-V.
* testsuite/gas/riscv/cv-alu-boundaries.d: New test.
* testsuite/gas/riscv/cv-alu-boundaries.l: New test.
* testsuite/gas/riscv/cv-alu-boundaries.s: New test.
* testsuite/gas/riscv/cv-alu-fail-march.d: New test.
* testsuite/gas/riscv/cv-alu-fail-march.l: New test.
* testsuite/gas/riscv/cv-alu-fail-march.s: New test.
* testsuite/gas/riscv/cv-alu-fail-operand-01.d: New test.
* testsuite/gas/riscv/cv-alu-fail-operand-01.l: New test.
* testsuite/gas/riscv/cv-alu-fail-operand-01.s: New test.
* testsuite/gas/riscv/cv-alu-fail-operand-02.d: New test.
* testsuite/gas/riscv/cv-alu-fail-operand-02.l: New test.
* testsuite/gas/riscv/cv-alu-fail-operand-02.s: New test.
* testsuite/gas/riscv/cv-alu-fail-operand-03.d: New test.
* testsuite/gas/riscv/cv-alu-fail-operand-03.l: New test.
* testsuite/gas/riscv/cv-alu-fail-operand-03.s: New test.
* testsuite/gas/riscv/cv-alu-fail-operand-04.d: New test.
* testsuite/gas/riscv/cv-alu-fail-operand-04.l: New test.
* testsuite/gas/riscv/cv-alu-fail-operand-04.s: New test.
* testsuite/gas/riscv/cv-alu-fail-operand-05.d: New test.
* testsuite/gas/riscv/cv-alu-fail-operand-05.l: New test.
* testsuite/gas/riscv/cv-alu-fail-operand-05.s: New test.
* testsuite/gas/riscv/cv-alu-fail-operand-06.d: New test.
* testsuite/gas/riscv/cv-alu-fail-operand-06.l: New test.
* testsuite/gas/riscv/cv-alu-fail-operand-06.s: New test.
* testsuite/gas/riscv/cv-alu-fail-operand-07.d: New test.
* testsuite/gas/riscv/cv-alu-fail-operand-07.l: New test.
* testsuite/gas/riscv/cv-alu-fail-operand-07.s: New test.
* testsuite/gas/riscv/cv-alu-insns.d: New test.
* testsuite/gas/riscv/cv-alu-insns.s: New test.
opcodes/ChangeLog:
* riscv-dis.c (print_insn_args): Disassemble xcb operand.
* riscv-opc.c: Defined the MASK and added XCValu instructions.
include/ChangeLog:
* opcode/riscv-opc.h: Added corresponding MATCH and MASK macros
for XCValu.
* opcode/riscv.h: Added corresponding EXTRACT and ENCODE macros
for XCValu.
(enum riscv_insn_class): Added the XCValu instruction class.
|
|
Spec: https://docs.openhwgroup.org/projects/cv32e40p-user-manual/en/latest/instruction_set_extensions.html
Contributors:
Mary Bennett <mary.bennett@embecosm.com>
Nandni Jamnadas <nandni.jamnadas@embecosm.com>
Pietra Ferreira <pietra.ferreira@embecosm.com>
Charlie Keaney
Jessica Mills
Craig Blackmore <craig.blackmore@embecosm.com>
Simon Cook <simon.cook@embecosm.com>
Jeremy Bennett <jeremy.bennett@embecosm.com>
Helene Chelin <helene.chelin@embecosm.com>
bfd/ChangeLog:
* elfxx-riscv.c (riscv_multi_subset_supports): Added `xcvmac`
instruction class.
(riscv_multi_subset_supports_ext): Likewise.
gas/ChangeLog:
* config/tc-riscv.c (validate_riscv_insn): Added the necessary
operands for the extension.
(riscv_ip): Likewise.
* doc/c-riscv.texi: Noted XCVmac as an additional ISA extension
for CORE-V.
* testsuite/gas/riscv/cv-mac-fail-march.d: New test.
* testsuite/gas/riscv/cv-mac-fail-march.l: New test.
* testsuite/gas/riscv/cv-mac-fail-march.s: New test.
* testsuite/gas/riscv/cv-mac-fail-operand.d: New test.
* testsuite/gas/riscv/cv-mac-fail-operand.l: New test.
* testsuite/gas/riscv/cv-mac-fail-operand.s: New test.
* testsuite/gas/riscv/cv-mac-insns.d: New test.
* testsuite/gas/riscv/cv-mac-insns.s: New test.
opcodes/ChangeLog:
* riscv-dis.c (print_insn_args): Disassemble information with
the EXTRACT macro implemented.
* riscv-opc.c: Defined the MASK and added
XCVmac instructions.
include/ChangeLog:
* opcode/riscv-opc.h: Added corresponding MATCH and MASK macros
for XCVmac.
* opcode/riscv.h: Added corresponding EXTRACT and ENCODE macros
for uimm.
(enum riscv_insn_class): Added the XCVmac instruction class.
|
|
Just the lightest modifications about this, without any further checks and
considering --emit-relocs. We will need to improve it in the future, but
first do this to avoid conflicts between linker internal relocations and the
new definition of psabi. For example, TLSDESC relocs.
Passed riscv-gnu-toolchain regressions, so should be safe enough to commit.
Co-authored-by: Tsukasa OI <research_trasio@irq.a4lg.com>
bfd/
* reloc.c: Removed linker internal relocations.
* bfd-in2.h: Regenerated.
* libbfd.h: Regenerated.
* elfnn-riscv.c: Defined R_RISCV_DELETE in include/elf/riscv.h.
* elfxx-riscv.c (howto_table, howto_table_internal): Moved linker
internal relocations from howto_table into howto_table_internal.
(riscv_reloc_map): Removed linker internal relocations mapping.
(riscv_elf_rtype_to_howto): Return howto of linker internal
relocations from howto_table_internal.
include/
* elf/riscv.h: Defined linker internal relocations after R_RISCV_max.
|
|
Within the groups L{B,BU,H,HU,W,WU,D}, S{B,H,W,D}, FL{H,W,D,Q}, and
FS{H,W,D,Q} the sole difference between the handling is the insn
mnemonic passed to the common handling functions. The intended mnemonic,
however, can easily be retrieved. Furthermore leverags that Sx and FSx
are then handled identically, too, and hence their cases can also be
folded.
|
|
This patch adds support for Guarded control stack data synchronization
instruction (GCSB DSYNC). This instruction is allocated to existing
HINT space and uses the HINT number 19 and to match this an entry is
added to the aarch64_hint_options array.
|
|
This patch adds for Guarded Control Stack Extension (GCS) extension. GCS feature is
optional from Armv9.4-A architecture and enabled by passing +gcs option to -march
(eg: -march=armv9.4-a+gcs) or using ".arch_extension gcs" directive in the assembly file.
Also this patch adds support for GCS instructions gcspushx, gcspopcx, gcspopx,
gcsss1, gcsss2, gcspushm, gcspopm, gcsstr and gcssttr.
|
|
This patch adds support for Check Feature Status Extension (CHK) which
is mandatory from Armv8.0-A. Also this patch supports "chkfeat" instruction
(hint #40).
|
|
This patch adds AArch64 support for Armv8.9-A architecture (-march=armv8.9-a)
and Armv9.4-A architecture (-march=armv9.4-a).
|
|
|
|
This patch adds the R_MICROBLAZE_32_NONE relocation type.
This is a 32-bit reloc that stores the 32-bit pc relative
value in two words (with an imm instruction).
Add test case to gas test suite.
Signed-off-by: Neal Frager <neal.frager@amd.com>
Signed-off-by: Michael J. Eager <eager@eagercon.com>
|
|
This is for consistency and to prevent possible unnecessary errors due
to this inconsistency.
include/ChangeLog:
* opcode/riscv-opc.h (DECLARE_INSN): Remove semicolons from the
end of each entry.
|
|
include/ChangeLog:
* opcode/riscv-opc.h: Fix typo.
|
|
For the instructions of R_LARCH_B16/B21, if the immediate overflow,
add a B instruction and R_LARCH_B26 relocation.
For example:
.L1
...
blt $t0, $t1, .L1
R_LARCH_B16
change to:
.L1
...
bge $t0, $t1, .L2
b .L1
R_LARCH_B26
.L2
|