| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
This patch adds support for the new SPARC M8 processor (implementing OSA
2017) to binutils.
New instructions:
- Dictionary Unpack
+ dictunpack
- Partitioned Compare with shifted result
+ Signed variants: fpcmp{le,gt,eq,ne}{8,16,32}shl
+ Unsigned variants: fpcmpu{le,gt}{8,16,32}shl
- Partitioned Dual-Equal compared, with shifted result
+ fpcmpde{8,16,32}shl
- Partitioned Unsigned Range Compare, with shifted result
+ fpcmpur{8,16,32}shl
- 64-bit shifts on Floating-Point registers
+ fps{ll,ra,rl}64x
- Misaligned loads and stores
+ ldm{sh,uh,sw,uw,x,ux}
+ ldm{sh,uh,sw,uw,x,ux}a
+ ldmf{s,d}
+ ldmf{s,d}a
+ stm{h,w,x}
+ stm{h,w,x}a
+ stmf{s,d}
+ stmf{s,d}a
- Oracle Numbers
+ on{add,sub,mul,div}
- Reverse Bytes/Bits
+ revbitsb
+ revbytes{h,w,x}
- Run-Length instructions
+ rle_burst
+ rle_length
- New crypto instructions
+ sha3
- Instruction to read the new register %entropy
+ rd %entropy
New Alternate Address Identifiers:
- 0x24, #ASI_CORE_COMMIT_COUNT
- 0x24, #ASI_CORE_SELECT_COUNT
- 0x48, #ASI_ARF_ECC_REG
- 0x53, #ASI_ITLB_PROBE
- 0x58, #ASI_DSFAR
- 0x5a, #ASI_DTLB_PROBE_PRIMARY
- 0x5b, #ASI_DTLB_PROBE_REAL
- 0x64, #ASI_CORE_SELECT_COMMIT_NHT
The new assembler command-line options for selecting the M8 architecture
are:
-Av9m8 or -Asparc6 for 64-bit binaries.
-Av8plusm8 for 32-bit (v8+) binaries.
The corresponding disassembler command-line options are:
-msparc:v9m8 for 64-bit binaries.
-msparc:v8plusm8 for 32-bit (v8+) binaries.
Tested for regressions in the following targets:
sparc-aout sparc-linux sparc-vxworks sparc64-linux
bfd/ChangeLog:
2017-05-19 Jose E. Marchesi <jose.marchesi@oracle.com>
* archures.c (bfd_mach_sparc_v9m8): Define.
(bfd_mach_sparc_v8plusm8): Likewise.
(bfd_mach_sparc_v9_p): Adjust to M8.
(bfd_mach_sparc_64bit_p): Likewise.
* aoutx.h (machine_type): Handle bfd_mach_sparc_v9m8 and
bfd_mach_sparc_v8plusm8.
* bfd-in2.h: Regenerated.
* cpu-sparc.c (arch_info_struct): Entries for sparc:v9m8 and
sparc:v8plusm8.
* elfxx-sparc.c (_bfd_sparc_elf_object_p): Handle
bfd_mach_sparc_v8plusm8 and bfd_mach_sparc_v9m8 using the new hw
capabilities ONADDSUB, ONMUL, ONDIV, DICTUNP, FPCPSHL, RLE and
SHA3.
* elf32-sparc.c (elf32_sparc_final_write_processing): Handle
bfd_mach_sparc_v8plusm8.
binutils/ChangeLog:
2017-05-19 Jose E. Marchesi <jose.marchesi@oracle.com>
* NEWS: Mention the SPARC M8 support.
gas/ChangeLog:
2017-05-19 Jose E. Marchesi <jose.marchesi@oracle.com>
* config/tc-sparc.c (sparc_arch_table): Entries for `sparc6',
`v9m8' and `v8plusm8'.
(sparc_md_end): Handle SPARC_OPCODE_ARCH_M8.
(get_hwcap_name): Support the M8 hardware capabilities.
(sparc_ip): Handle new operand types.
* doc/c-sparc.texi (Sparc-Opts): Document -Av9m8, -Av8plusm8 and
-Asparc6, and the corresponding -xarch aliases.
* testsuite/gas/sparc/sparc6.s: New file.
* testsuite/gas/sparc/sparc6.d: Likewise.
* testsuite/gas/sparc/sparc6-diag.s: Likewise.
* testsuite/gas/sparc/sparc6-diag.l: Likewise.
* testsuite/gas/sparc/fpcmpshl.s: Likewise.
* testsuite/gas/sparc/fpcmpshl.d: Likewise.
* testsuite/gas/sparc/fpcmpshl-diag.s: Likewise.
* testsuite/gas/sparc/fpcmpshl-diag.l: Likewise.
* testsuite/gas/sparc/ldm-stm.s: Likewise.
* testsuite/gas/sparc/ldm-stm.d: Likewise.
* testsuite/gas/sparc/ldm-stm-diag.s: Likewise.
* testsuite/gas/sparc/ldm-stm-diag.l: Likewise.
* testsuite/gas/sparc/ldmf-stmf.s: Likewise.
* testsuite/gas/sparc/ldmf-stmf.d: Likewise.
* testsuite/gas/sparc/ldmf-stmf-diag.s: Likewise.
* testsuite/gas/sparc/ldmf-stmf-diag.l: Likewise.
* testsuite/gas/sparc/on.s: Likewise.
* testsuite/gas/sparc/on.d: Likewise.
* testsuite/gas/sparc/on-diag.s: Likewise.
* testsuite/gas/sparc/on-diag.l: Likewise.
* testsuite/gas/sparc/rle.s: Likewise.
* testsuite/gas/sparc/rle.d: Likewise.
* testsuite/gas/sparc/sparc.exp (gas_64_check): Run new tests.
* testsuite/gas/sparc/rdasr.s: Add test for RDENTROPY.
* testsuite/gas/sparc/rdasr.d: Likewise.
include/ChangeLog:
2017-05-19 Jose E. Marchesi <jose.marchesi@oracle.com>
* elf/sparc.h (ELF_SPARC_HWCAP2_SPARC6): Define.
(ELF_SPARC_HWCAP2_ONADDSUB): Likewise.
(ELF_SPARC_HWCAP2_ONMUL): Likewise.
(ELF_SPARC_HWCAP2_ONDIV): Likewise.
(ELF_SPARC_HWCAP2_DICTUNP): Likewise.
(ELF_SPARC_HWCAP2_FPCMPSHL): Likewise.
(ELF_SPARC_HWCAP2_RLE): Likewise.
(ELF_SPARC_HWCAP2_SHA3): Likewise.
* opcode/sparc.h (sparc_opcode_arch_val): Add SPARC_OPCODE_ARCH_M8
and adjust SPARC_OPCODE_ARCH_MAX.
(HWCAP2_SPARC6): Define.
(HWCAP2_ONADDSUB): Likewise.
(HWCAP2_ONMUL): Likewise.
(HWCAP2_ONDIV): Likewise.
(HWCAP2_DICTUNP): Likewise.
(HWCAP2_FPCMPSHL): Likewise.
(HWCAP2_RLE): Likewise.
(HWCAP2_SHA3): Likewise.
(OPM): Likewise.
(OPMI): Likewise.
(ONFCN): Likewise.
(REVFCN): Likewise.
(SIMM10): Likewise.
opcodes/ChangeLog:
2017-05-19 Jose E. Marchesi <jose.marchesi@oracle.com>
* sparc-dis.c (MASK_V9): Include SPARC_OPCODE_ARCH_M8.
(X_IMM2): Define.
(compute_arch_mask): Handle bfd_mach_sparc_v8plusm8 and
bfd_mach_sparc_v9m8.
(print_insn_sparc): Handle new operand types.
* sparc-opc.c (MASK_M8): Define.
(v6): Add MASK_M8.
(v6notlet): Likewise.
(v7): Likewise.
(v8): Likewise.
(v9): Likewise.
(v9a): Likewise.
(v9b): Likewise.
(v9c): Likewise.
(v9d): Likewise.
(v9e): Likewise.
(v9v): Likewise.
(v9m): Likewise.
(v9andleon): Likewise.
(m8): Define.
(HWS_VM8): Define.
(HWS2_VM8): Likewise.
(sparc_opcode_archs): Add entry for "m8".
(sparc_opcodes): Add OSA2017 and M8 instructions
dictunpack, fpcmp{ule,ugt,eq,ne,de,ur}{8,16,32}shl,
fpx{ll,ra,rl}64x,
ldm{sh,uh,sw,uw,x,ux}, ldm{sh,uh,sw,uw,x,ux}a, ldmf{s,d},
ldmf{s,d}a, on{add,sub,mul,div}, rdentropy, revbitsb,
revbytes{h,w,x}, rle_burst, rle_length, sha3, stm{h,w,x},
stm{h,w,x}a, stmf{s,d}, stmf{s,d}a.
(asi_table): New M8 ASIs ASI_CORE_COMMIT_COUNT,
ASI_CORE_SELECT_COUNT, ASI_ARF_ECC_REG, ASI_ITLB_PROBE, ASI_DSFAR,
ASI_DTLB_PROBE_PRIMARY, ASI_DTLB_PROBE_REAL,
ASI_CORE_SELECT_COMMIT_NHT.
|
|
Since the flag is now set only for regular object refs.
include/
* bfdlink.h (struct bfd_link_hash_entry <non_ir_ref>): Rename to
non_ir_ref_regular.
bfd/
* elf-m10300.c: Rename occurrences of non_ir_ref.
* elf32-arm.c: Likewise.
* elf32-bfin.c: Likewise.
* elf32-cr16.c: Likewise.
* elf32-cris.c: Likewise.
* elf32-d10v.c: Likewise.
* elf32-dlx.c: Likewise.
* elf32-fr30.c: Likewise.
* elf32-frv.c: Likewise.
* elf32-hppa.c: Likewise.
* elf32-i370.c: Likewise.
* elf32-i386.c: Likewise.
* elf32-iq2000.c: Likewise.
* elf32-lm32.c: Likewise.
* elf32-m32c.c: Likewise.
* elf32-m32r.c: Likewise.
* elf32-m68hc1x.c: Likewise.
* elf32-m68k.c: Likewise.
* elf32-mcore.c: Likewise.
* elf32-metag.c: Likewise.
* elf32-microblaze.c: Likewise.
* elf32-moxie.c: Likewise.
* elf32-msp430.c: Likewise.
* elf32-mt.c: Likewise.
* elf32-nios2.c: Likewise.
* elf32-or1k.c: Likewise.
* elf32-ppc.c: Likewise.
* elf32-rl78.c: Likewise.
* elf32-s390.c: Likewise.
* elf32-score.c: Likewise.
* elf32-score7.c: Likewise.
* elf32-sh.c: Likewise.
* elf32-tic6x.c: Likewise.
* elf32-tilepro.c: Likewise.
* elf32-v850.c: Likewise.
* elf32-vax.c: Likewise.
* elf32-xstormy16.c: Likewise.
* elf32-xtensa.c: Likewise.
* elf64-alpha.c: Likewise.
* elf64-hppa.c: Likewise.
* elf64-ia64-vms.c: Likewise.
* elf64-mmix.c: Likewise.
* elf64-ppc.c: Likewise.
* elf64-s390.c: Likewise.
* elf64-sh64.c: Likewise.
* elf64-x86-64.c: Likewise.
* elflink.c: Likewise.
* elfnn-aarch64.c: Likewise.
* elfnn-ia64.c: Likewise.
* elfnn-riscv.c: Likewise.
* elfxx-mips.c: Likewise.
* elfxx-sparc.c: Likewise.
* elfxx-tilegx.c: Likewise.
* linker.c: Likewise.
ld/
* plugin.c: Rename occurrences of non_ir_ref.
|
|
dynamic_ref_after_ir_def is a little odd compared to other symbol
flags in that as the name suggests, it is set only for certain
references after a definition. It turns out that setting a flag for
any non-ir reference from a dynamic object can be used to solve the
problem for which this flag was invented, which I think is a cleaner.
This patch does that, and sets non_ir_ref only for regular object
references.
include/
* bfdlink.h (struct bfd_link_hash_entry): Update non_ir_ref
comment. Rename dynamic_ref_after_ir_def to non_ir_ref_dynamic.
ld/
* plugin.c (is_visible_from_outside): Use non_ir_ref_dynamic.
(plugin_notice): Set non_ir_ref for references from regular
objects, non_ir_ref_dynamic for references from dynamic objects.
bfd/
* elf64-ppc.c (add_symbol_adjust): Transfer non_ir_ref_dynamic.
* elflink.c (elf_link_add_object_symbols): Update to use
non_ir_ref_dynamic.
(elf_link_input_bfd): Test non_ir_ref_dynamic in addition to
non_ir_ref.
* linker.c (_bfd_generic_link_add_one_symbol): Likewise.
|
|
Add MIPS16e2 ASE support as per the architecture specification[1],
including in particular:
1. A new ELF ASE flag to mark MIPS16e2 binaries.
2. MIPS16e2 instruction assembly support, including a relaxation update
to use LUI rather than an LI/SLL instruction pair for loading the
high part of 32-bit addresses.
3. MIPS16e2 instruction disassembly support, including updated rules for
extended forms of instructions that are now subdecoded and therefore
do not alias to the original MIPS16 ISA revision instructions even
for encodings that are not valid in the MIPS16e2 instruction set.
Add `-mmips16e2' and `-mno-mips16e2' GAS command-line options and their
corresponding `mips16e2' and `no-mips16e2' settings for the `.set' and
`.module' pseudo-ops. Control the availability of the MT ASE subset of
the MIPS16e2 instruction set with a combination of these controls and
the preexisting MT ASE controls.
Parts of this change by Matthew Fortune and Andrew Bennett.
References:
[1] "MIPS32 Architecture for Programmers: MIPS16e2 Application-Specific
Extension Technical Reference Manual", Imagination Technologies
Ltd., Document Number: MD01172, Revision 01.00, April 26, 2016
include/
* elf/mips.h (AFL_ASE_MIPS16E2): New macro.
(AFL_ASE_MASK): Adjust accordingly.
* opcode/mips.h: Document new operand codes defined.
(mips_operand_type): Add OP_REG28 enum value.
(INSN2_SHORT_ONLY): Update description.
(ASE_MIPS16E2, ASE_MIPS16E2_MT): New macros.
bfd/
* elfxx-mips.c (print_mips_ases): Handle MIPS16e2 ASE.
opcodes/
* mips-dis.c (mips_arch_choices): Add ASE_MIPS16E2 and
ASE_MIPS16E2_MT flags to the unnamed MIPS16 entry.
(mips_convert_abiflags_ases): Handle the AFL_ASE_MIPS16E2 flag.
(print_insn_arg) <OP_REG28>: Add handler.
(validate_insn_args) <OP_REG28>: Handle.
(print_mips16_insn_arg): Handle MIPS16 instructions that require
32-bit encoding and 9-bit immediates.
(print_insn_mips16): Handle MIPS16 instructions that require
32-bit encoding and MFC0/MTC0 operand decoding.
* mips16-opc.c (decode_mips16_operand) <'>', '9', 'G', 'N', 'O'>
<'Q', 'T', 'b', 'c', 'd', 'r', 'u'>: Add handlers.
(RD_C0, WR_C0, E2, E2MT): New macros.
(mips16_opcodes): Add entries for MIPS16e2 instructions:
GP-relative "addiu" and its "addu" spelling, "andi", "cache",
"di", "ehb", "ei", "ext", "ins", GP-relative "lb", "lbu", "lh",
"lhu", and "lw" instructions, "ll", "lui", "lwl", "lwr", "mfc0",
"movn", "movtn", "movtz", "movz", "mtc0", "ori", "pause",
"pref", "rdhwr", "sc", GP-relative "sb", "sh" and "sw"
instructions, "swl", "swr", "sync" and its "sync_acquire",
"sync_mb", "sync_release", "sync_rmb" and "sync_wmb" aliases,
"xori", "dmt", "dvpe", "emt" and "evpe". Add split
regular/extended entries for original MIPS16 ISA revision
instructions whose extended forms are subdecoded in the MIPS16e2
ISA revision: "li", "sll" and "srl".
binutils/
* readelf.c (print_mips_ases): Handle MIPS16e2 ASE.
* NEWS: Mention MIPS16e2 ASE support.
gas/
* config/tc-mips.c (RELAX_MIPS16_ENCODE): Add `e2' flag.
(RELAX_MIPS16_E2): New macro.
(RELAX_MIPS16_PIC, RELAX_MIPS16_SYM32, RELAX_MIPS16_NOMACRO)
(RELAX_MIPS16_USER_SMALL, RELAX_MIPS16_USER_EXT)
(RELAX_MIPS16_DSLOT, RELAX_MIPS16_JAL_DSLOT)
(RELAX_MIPS16_EXTENDED, RELAX_MIPS16_MARK_EXTENDED)
(RELAX_MIPS16_CLEAR_EXTENDED, RELAX_MIPS16_ALWAYS_EXTENDED)
(RELAX_MIPS16_MARK_ALWAYS_EXTENDED)
(RELAX_MIPS16_CLEAR_ALWAYS_EXTENDED, RELAX_MIPS16_MACRO)
(RELAX_MIPS16_MARK_MACRO, RELAX_MIPS16_CLEAR_MACRO): Shift bits.
(mips16_immed_extend): New prototype.
(options): Add OPTION_MIPS16E2 and OPTION_NO_MIPS16E2 enum
values.
(md_longopts): Add "mmips16e2" and "mno-mips16e2" options.
(mips_ases): Add "mips16e2" entry.
(mips_set_ase): Handle MIPS16e2 ASE.
(insn_insert_operand): Explicitly handle immediates with MIPS16
instructions that require 32-bit encoding.
(is_opcode_valid_16): Pass enabled ASE bitmask on to
`opcode_is_member'.
(validate_mips_insn): Explicitly handle immediates with MIPS16
instructions that require 32-bit encoding.
(operand_reg_mask) <OP_REG28>: Add handler.
(match_reg28_operand): New function.
(match_operand) <OP_REG28>: Add handler.
(append_insn): Pass ASE_MIPS16E2 setting to RELAX_MIPS16_ENCODE.
(match_mips16_insn): Handle MIPS16 instructions that require
32-bit encoding and `V' and `u' operand codes.
(mips16_ip): Allow any characters except from `.' in opcodes.
(mips16_immed_extend): Handle 9-bit immediates. Do not shuffle
immediates whose width is not one of these listed.
(md_estimate_size_before_relax): Handle MIPS16e2 relaxation.
(mips_relax_frag): Likewise.
(md_convert_frag): Likewise.
(mips_convert_ase_flags): Handle MIPS16e2 ASE.
* doc/as.texinfo (Target MIPS options): Add `-mmips16e2' and
`-mno-mips16e2' options.
(-mmips16e2, -mno-mips16e2): New options.
* doc/c-mips.texi (MIPS Options): Add `-mmips16e2' and
`-mno-mips16e2' options.
(MIPS ASE Instruction Generation Overrides): Add `.set mips16e2'
and `.set nomips16e2'.
|
|
|
|
gas/
2017-05-10 Claudiu Zissulescu <claziss@synopsys.com>
* testsuite/gas/arc/attr-arc600.d: New file.
* testsuite/gas/arc/attr-arc600_mul32x16.d: Likewise.
* testsuite/gas/arc/attr-arc600_norm.d: Likewise.
* testsuite/gas/arc/attr-arc601.d: Likewise.
* testsuite/gas/arc/attr-arc601_mul32x16.d: Likewise.
* testsuite/gas/arc/attr-arc601_mul64.d: Likewise.
* testsuite/gas/arc/attr-arc601_norm.d: Likewise.
* testsuite/gas/arc/attr-arc700.d: Likewise.
* testsuite/gas/arc/attr-arcem.d: Likewise.
* testsuite/gas/arc/attr-archs.d: Likewise.
* testsuite/gas/arc/attr-autodetect-1.d: Likewise.
* testsuite/gas/arc/attr-autodetect-1.s: Likewise.
* testsuite/gas/arc/attr-cpu-a601.d: Likewise.
* testsuite/gas/arc/attr-cpu-a601.s: Likewise.
* testsuite/gas/arc/attr-cpu-a700.d: Likewise.
* testsuite/gas/arc/attr-cpu-a700.s: Likewise.
* testsuite/gas/arc/attr-cpu-em.d: Likewise.
* testsuite/gas/arc/attr-cpu-em.s: Likewise.
* testsuite/gas/arc/attr-cpu-hs.d: Likewise.
* testsuite/gas/arc/attr-cpu-hs.s: Likewise.
* testsuite/gas/arc/attr-em.d: Likewise.
* testsuite/gas/arc/attr-em4.d: Likewise.
* testsuite/gas/arc/attr-em4_dmips.d: Likewise.
* testsuite/gas/arc/attr-em4_fpuda.d: Likewise.
* testsuite/gas/arc/attr-em4_fpus.d: Likewise.
* testsuite/gas/arc/attr-hs.d: Likewise.
* testsuite/gas/arc/attr-hs34.d: Likewise.
* testsuite/gas/arc/attr-hs38.d: Likewise.
* testsuite/gas/arc/attr-hs38_linux.d: Likewise.
* testsuite/gas/arc/attr-mul64.d: Likewise.
* testsuite/gas/arc/attr-name.d: Likewise.
* testsuite/gas/arc/attr-name.s: Likewise.
* testsuite/gas/arc/attr-nps400.d: Likewise.
* testsuite/gas/arc/attr-override-mcpu.d: Likewise.
* testsuite/gas/arc/attr-override-mcpu.s
* testsuite/gas/arc/attr-quarkse_em.d: Likewise.
* testsuite/gas/arc/blank.s: Likewise.
* testsuite/gas/elf/section2.e-arc: Likewise.
* testsuite/gas/arc/cpu-pseudop-1.d: Update test.
* testsuite/gas/arc/cpu-pseudop-2.d: Likewise.
* testsuite/gas/arc/nps400-0.d: Likewise.
* testsuite/gas/elf/elf.exp: Set target_machine for ARC.
* config/tc-arc.c (opcode/arc-attrs.h): Include.
(ARC_GET_FLAG, ARC_SET_FLAG, streq): Define.
(arc_attribute): Declare new function.
(md_pseudo_table): Add arc_attribute.
(cpu_types): Rename default cpu features.
(selected_cpu): Set the default OSABI flag.
(mpy_option): New variable.
(pic_option): Likewise.
(sda_option): Likewise.
(tls_option): Likewise.
(feature_type, feature_list): Remove.
(arc_initial_eflag): Likewise.
(attributes_set_explicitly): New variable.
(arc_check_feature): Check also for the conflicting features.
(arc_select_cpu): Refactor assignment of selected_cpu.eflags.
(arc_option): Remove setting of private flags and architecture.
(check_cpu_feature): Refactor feature names.
(autodetect_attributes): New function.
(assemble_tokens): Use above function.
(md_parse_option): Refactor feature names.
(arc_attribute): New function.
(arc_set_attribute_int): Likewise.
(arc_set_attribute_string): Likewise.
(arc_stralloc): Likewise.
(arc_set_public_attributes): Likewise.
(arc_md_end): Likewise.
(arc_copy_symbol_attributes): Likewise.
(rc_convert_symbolic_attribute): Likewise.
* config/tc-arc.h (md_end): Define.
(CONVERT_SYMBOLIC_ATTRIBUTE): Likewise.
(TC_COPY_SYMBOL_ATTRIBUTES): Likewise.
* doc/c-arc.texi: Document ARC object attributes.
binutils/
2017-05-10 Claudiu Zissulescu <claziss@synopsys.com>
* readelf.c (decode_ARC_machine_flags): Recognize OSABI v4.
(get_arc_section_type_name): New function.
(get_section_type_name): Use the above function.
(display_arc_attribute): New function.
(process_arc_specific): Likewise.
(process_arch_specific): Handle ARC specific information.
* testsuite/binutils-all/strip-3.d: Consider ARC.attributes
section.
include/
2017-05-10 Claudiu Zissulescu <claziss@synopsys.com>
* elf/arc.h (SHT_ARC_ATTRIBUTES): Define.
(Tag_ARC_*): Define.
(E_ARC_OSABI_V4): Define.
(E_ARC_OSABI_CURRENT): Reassign it.
(TAG_CPU_*): Define.
* opcode/arc-attrs.h: New file.
* opcode/arc.h (insn_subclass_t): Assign enum values.
(insn_subclass_t): Update enum with QUARKSE1, QUARKSE2, and LL64.
(ARC_EA, ARC_CD, ARC_LLOCK, ARC_ATOMIC, ARC_MPY, ARC_MULT)
(ARC_NPS400, ARC_DPFP, ARC_SPFP, ARC_FPU, ARC_FPUDA, ARC_SWAP)
(ARC_NORM, ARC_BSCAN, ARC_UIX, ARC_TSTAMP, ARC_VBFDW)
(ARC_BARREL, ARC_DSPA, ARC_SHIFT, ARC_INTR, ARC_DIV, ARC_XMAC)
(ARC_CRC): Delete.
bfd/
2017-05-10 Claudiu Zissulescu <claziss@synopsys.com>
* elf32-arc.c (FEATURE_LIST_NAME): Define.
(CONFLICT_LIST): Likewise.
(opcode/arc-attrs.h): Include.
(arc_elf_print_private_bfd_data): Print OSABI v4 flag.
(arc_extract_features): New file.
(arc_stralloc): Likewise.
(arc_elf_merge_attributes): Likewise.
(arc_elf_merge_private_bfd_data): Use object attributes.
(bfd_arc_get_mach_from_attributes): New function.
(arc_elf_object_p): Use object attributes.
(arc_elf_final_write_processing): Likewise.
(elf32_arc_obj_attrs_arg_type): New function.
(elf32_arc_obj_attrs_handle_unknown): Likewise.
(elf32_arc_section_from_shdr): Likewise.
(elf_backend_obj_attrs_vendor): Define.
(elf_backend_obj_attrs_section): Likewise.
(elf_backend_obj_attrs_arg_type): Likewise.
(elf_backend_obj_attrs_section_type): Likewise.
(elf_backend_obj_attrs_handle_unknown): Likewise.
(elf_backend_section_from_shdr): Likewise.
ld/
2017-05-10 Claudiu Zissulescu <claziss@synopsys.com>
* testsuite/ld-arc/attr-merge-0.d: New file.
* testsuite/ld-arc/attr-merge-0.s: Likewise.
* testsuite/ld-arc/attr-merge-0e.s: Likewise.
* testsuite/ld-arc/attr-merge-1.d: Likewise.
* testsuite/ld-arc/attr-merge-1.s: Likewise.
* testsuite/ld-arc/attr-merge-1e.s: Likewise.
* testsuite/ld-arc/attr-merge-2.d: Likewise.
* testsuite/ld-arc/attr-merge-2.s: Likewise.
* testsuite/ld-arc/attr-merge-3.d: Likewise.
* testsuite/ld-arc/attr-merge-3.s: Likewise.
* testsuite/ld-arc/attr-merge-3e.s: Likewise.
* testsuite/ld-arc/attr-merge-4.s: Likewise.
* testsuite/ld-arc/attr-merge-5.d: Likewise.
* testsuite/ld-arc/attr-merge-5a.s: Likewise.
* testsuite/ld-arc/attr-merge-5b.s: Likewise.
* testsuite/ld-arc/attr-merge-conflict-isa.d: Likewise.
* testsuite/ld-arc/attr-merge-err-isa.d: Likewise.
* testsuite/ld-arc/attr-merge-incompatible-cpu.d: Likewise.
* testsuite/ld-arc/got-01.d: Update test.
* testsuite/ld-arc/attr-merge-err-quarkse.d: New file.
* testsuite/ld-arc/attr-quarkse.s: Likewise.
* testsuite/ld-arc/attr-quarkse2.s: Likewise.
opcodes/
2017-05-10 Claudiu Zissulescu <claziss@synopsys.com>
* arc-dis.c (parse_option): Update quarkse_em option..
* arc-ext-tbl.h (dsp_fp_flt2i, dsp_fp_i2flt): Change subclass to
QUARKSE1.
(dsp_fp_div, dsp_fp_cmp): Change subclass to QUARKSE2.
|
|
We need to make an IR symbol visible if it is defined in an IR object
and referenced in a dynamic object. When --as-needed is used, since
linker removes the IR symbol reference of the dynamic object if the
dynamic object isn't needed in the first pass, the IR definition isn't
visible to the dynamic object even if the dynamic object becomes needed
in the second pass. Add dynamic_ref_after_ir_def to bfd_link_hash_entry
to track IR symbol which is defined in an IR object and later referenced
in a dynamic object. dynamic_ref_after_ir_def is preserved when restoring
the symbol table for unneeded dynamic object.
bfd/
PR ld/21382
* elflink.c (elf_link_add_object_symbols): Preserve
dynamic_ref_after_ir_def when restoring the symbol table for
unneeded dynamic object.
include/
PR ld/21382
* bfdlink.h (bfd_link_hash_entry): Add dynamic_ref_after_ir_def.
ld/
PR ld/21382
* plugin.c (is_visible_from_outside): Symbol may be visible
from outside if dynamic_ref_after_ir_def is set.
(plugin_notice): Set dynamic_ref_after_ir_def if the symbol is
defined in an IR object and referenced in a dynamic object.
* testsuite/ld-plugin/lto.exp: Run PR ld/21382 tests.
* testsuite/ld-plugin/pr21382a.c: New file.
* testsuite/ld-plugin/pr21382b.c: Likewise.
|
|
-z nodynamic-undefined-weak is only implemented for x86. (The sparc
backend has some support code but doesn't enable the option by
including ld/emulparams/dynamic_undefined_weak.sh, and since the
support looks like it may be broken I haven't enabled it.) This patch
adds the complementary -z dynamic-undefined-weak, extends both options
to affect building of shared libraries as well as executables, and
adds support for the option on powerpc.
include/
* bfdlink.h (struct bfd_link_info <dynamic_undefined_weak>):
Revise comment.
bfd/
* elflink.c (_bfd_elf_adjust_dynamic_symbol): Hide undefweak
or make dynamic for info->dynamic_undefined_weak 0 and 1.
* elf32-ppc.c:Formatting.
(ensure_undefweak_dynamic): Don't make dynamic when
info->dynamic_undefined_weak is zero.
(allocate_dynrelocs): Discard undefweak dyn_relocs for
info->dynamic_undefined_weak. Discard undef dyn_relocs when
not default visibility. Discard undef and undefweak
dyn_relocs earlier.
(ppc_elf_relocate_section): Adjust to suit.
* elf64-ppc.c: Formatting.
(ensure_undefweak_dynamic): Don't make dynamic when
info->dynamic_undefined_weak is zero.
(allocate_dynrelocs): Discard undefweak dyn_relocs for
info->dynamic_undefined_weak. Discard them earlier.
ld/
* ld.texinfo (dynamic-undefined-weak): Document.
(nodynamic-undefined-weak): Document that this option now can
be used with shared libs.
* emulparams/dynamic_undefined_weak.sh: Support -z
dynamic-undefined-weak.
* emulparams/elf32ppccommon.sh: Include dynamic_undefined_weak.sh.
* testsuite/ld-undefined/weak-undef.exp (undef_weak_so),
(undef_weak_exe): New. Use them. Add -z dynamic-undefined-weak
and -z nodynamic-undefined-weak tests.
* Makefile.am: Update powerpc dependencies.
* Makefile.in: Regenerate.
|
|
PPC_OPCODE_* renumbered to fill the gaps left by previous patches,
and reordered chronologically just because. I kept PPC_OPCODE_TMR
because presumably it might be used in future APUinfo for e6500.
include/
* opcode/ppc.h (PPC_OPCODE_*): Renumber and order chronologically.
(PPC_OPCODE_SPE): Comment on this and other bits used for APUinfo.
opcodes/
* ppc-dis.c (ppc_opts): Formatting. Set PPC_OPCODE_TMR for e6500.
* ppc-opc.c (powerpc_opcodes <mftmr, mttmr>): Remove now
unnecessary E6500.
|
|
The -mhtm option is fairly useless too.
include/
* opcode/ppc.h (PPC_OPCODE_HTM): Delete.
gas/
* config/tc-ppc.c (md_show_usage): Delete mention of -mhtm.
* testsuite/gas/ppc/htm.d: Pass -mpower8 and -Mpower8.
opcodes/
* ppc-dis.c (ppc_opts): Remove PPC_OPCODE_HTM and "htm".
* ppc-opc.c (PPCHTM): Define as PPC_OPCODE_POWER8.
|
|
This bit is also useless as it can be replaced with PPC_OPCODE_POWER9.
Defining the VSX2 and VSX3 selection based on cpu bits also lets the
assembler/disassembler distinguish between the power7 VSX opcodes and
the power8 ones. Note that this change means -mvsx now reverts back
to just adding the power7 VSX insns.
include/
* opcode/ppc.h (PPC_OPCODE_VSX3): Delete.
opcodes/
* ppc-dis.c (ppc_opts): Remove PPC_OPCODE_VSX3.
* ppc-opc.c (PPCVSX2): Define as PPC_OPCODE_POWER8.
(PPCVSX3): Define as PPC_OPCODE_POWER9.
|
|
This bit is worse than useless. Using it prevents the assembler and
disassembler distinguishing between opcodes added for power8 and those
added for power9.
include/
* opcode/ppc.h (PPC_OPCODE_ALTIVEC2): Delete.
opcodes/
* ppc-dis.c (ppc_opts): Remove PPC_OPCODE_ALTIVEC2.
* ppc-opc.c (PPCVEC2): Define as PPC_OPCODE_POWER8|PPC_OPCODE_E6500.
(PPCVEC3): Define as PPC_OPCODE_POWER9.
|
|
include * dis-asm.h: Add prototypes for wasm32 disassembler.
opcodes * Makefile.am: Add wasm32-dis.c.
* configure.ac: Add wasm32-dis.c to wasm32 target.
* disassemble.c: Add wasm32 disassembler code.
* wasm32-dis.c: New file.
* Makefile.in: Regenerate.
* configure: Regenerate.
* po/POTFILES.in: Regenerate.
* po/opcodes.pot: Regenerate.
gas * testsuite/gas/wasm32/allinsn.d: Adjust test for disassembler
changes.
* testsuite/gas/wasm32/disass.d: New test.
* testsuite/gas/wasm32/disass.s: New test.
* testsuite/gas/wasm32/disass-2.d: New test.
* testsuite/gas/wasm32/disass-2.s: New test.
* testsuite/gas/wasm32/reloc.d: Adjust test for changed reloc
names.
* testsuite/gas/wasm32/reloc.s: Update test for changed assembler
syntax.
* testsuite/gas/wasm32/wasm32.exp: Run new tests. Expect allinsn
test to succeed.
|
|
The memory disassemble_info::disassembler_options points to is always
owned by the client. I.e., that field is an non-owning, observing
pointer. Thus const makes sense.
Are the include/ and opcodes/ bits OK?
Tested on x86_64 Fedora 23, built with --enable-targets=all.
include/ChangeLog:
2017-04-05 Pedro Alves <palves@redhat.com>
* dis-asm.h (disassemble_info) <disassembler_options>: Now a
"const char *".
(next_disassembler_option): Constify.
opcodes/ChangeLog:
2017-04-05 Pedro Alves <palves@redhat.com>
* arc-dis.c (parse_option, parse_disassembler_options): Constify.
* arm-dis.c (parse_arm_disassembler_options): Constify.
* ppc-dis.c (powerpc_init_dialect): Constify local.
* vax-dis.c (parse_disassembler_options): Constify.
gdb/ChangeLog:
2017-04-05 Pedro Alves <palves@redhat.com>
* arm-tdep.c (show_disassembly_style_sfunc): Constify local.
* disasm.c (set_disassembler_options): Constify local.
* i386-tdep.c (i386_print_insn): Remove cast and FIXME comment.
|
|
Mark an ALLOC section, which should be placed in special memory area,
with SHF_GNU_MBIND. Its sh_info field indicates the special memory
type. GNU_MBIND section names start with ".mbind" so that they are
placed as orphan sections by linker. All input GNU_MBIND sections
with the same sh_type, sh_flags and sh_info are placed in one output
GNU_MBIND section. In executable and shared object, create a
GNU_MBIND segment for each GNU_MBIND section and its segment type is
PT_GNU_MBIND_LO plus the sh_info value. Each GNU_MBIND segment is
aligned at page boundary.
The assembler syntax:
.section .mbind.foo,"adx",%progbits
^ 0: Special memory type.
|
'd' for SHF_GNU_MBIND.
.section .mbind.foo,"adx",%progbits,0x1
^ 1: Special memory type.
|
'd' for SHF_GNU_MBIND.
.section .mbind.bar,"adG",%progbits,.foo_group,comdat,0x2
^ 2: Special memory type.
|
'd' for SHF_GNU_MBIND.
bfd/
* elf.c (get_program_header_size): Add a GNU_MBIND segment for
each GNU_MBIND section and align GNU_MBIND section to page size.
(_bfd_elf_map_sections_to_segments): Create a GNU_MBIND
segment for each GNU_MBIND section.
(_bfd_elf_init_private_section_data): Copy sh_info from input
for GNU_MBIND section.
binutils/
* NEWS: Mention support for ELF SHF_GNU_MBIND and
PT_GNU_MBIND_XXX.
* readelf.c (get_segment_type): Handle PT_GNU_MBIND_XXX.
(get_elf_section_flags): Handle SHF_GNU_MBIND.
(process_section_headers): Likewise.
* testsuite/binutils-all/mbind1.s: New file.
* testsuite/binutils-all/objcopy.exp: Run readelf test on
mbind1.s.
gas/
* NEWS: Mention support for ELF SHF_GNU_MBIND.
* config/obj-elf.c (section_match): New.
(get_section): Match both sh_info and group name.
(obj_elf_change_section): Add argument for sh_info. Pass both
sh_info and group name to get_section. Issue an error for
SHF_GNU_MBIND section without SHF_ALLOC. Set sh_info.
(obj_elf_parse_section_letters): Set SHF_GNU_MBIND for 'd'.
(obj_elf_section): Support SHF_GNU_MBIND section info.
* config/obj-elf.h (obj_elf_change_section): Add argument for
sh_info.
* config/tc-arm.c (start_unwind_section): Pass 0 as sh_info to
obj_elf_change_section.
* config/tc-ia64.c (obj_elf_vms_common): Likewise.
* config/tc-microblaze.c (microblaze_s_data): Likewise.
(microblaze_s_sdata): Likewise.
(microblaze_s_rdata): Likewise.
(microblaze_s_bss): Likewise.
* config/tc-mips.c (s_change_section): Likewise.
* config/tc-msp430.c (msp430_profiler): Likewise.
* config/tc-rx.c (parse_rx_section): Likewise.
* config/tc-tic6x.c (tic6x_start_unwind_section): Likewise.
* doc/as.texinfo: Document 'd' for SHF_GNU_MBIND.
* testsuite/gas/elf/elf.exp: Run section12a, section12b and
section13.
* testsuite/gas/elf/section10.d: Updated.
* testsuite/gas/elf/section10.s: Likewise.
* testsuite/gas/elf/section12.s: New file.
* testsuite/gas/elf/section12a.d: Likewise.
* testsuite/gas/elf/section12b.d: Likewise.
* testsuite/gas/elf/section13.l: Likewise.
* testsuite/gas/elf/section13.d: Likewise.
* testsuite/gas/elf/section13.s: Likewise.
include/
* elf/common.h (PT_GNU_MBIND_NUM): New.
(PT_GNU_MBIND_LO): Likewise.
(PT_GNU_MBIND_HI): Likewise.
(SHF_GNU_MBIND): Likewise.
ld/
* NEWS: Mention support for ELF SHF_GNU_MBIND and
PT_GNU_MBIND_XXX.
* emultempl/elf32.em (gld${EMULATION_NAME}_place_orphan): Place
input GNU_MBIND sections with the same type, attributes and
sh_info field into a single output GNU_MBIND section.
* testsuite/ld-elf/elf.exp: Run mbind2a and mbind2b.
* testsuite/ld-elf/mbind1.s: New file.
* testsuite/ld-elf/mbind1a.d: Likewise.
* testsuite/ld-elf/mbind1b.d: Likewise.
* testsuite/ld-elf/mbind1c.d: Likewise.
* testsuite/ld-elf/mbind2a.s: Likewise.
* testsuite/ld-elf/mbind2b.c: Likewise.
|
|
We missed a "_gp" when changing the GP symbol. To make sure that
doesn't happen again, we now use the same definition everywhere (thanks,
Nick).
include/ChangeLog:
2017-04-03 Palmer Dabbelt <palmer@dabbelt.com>
* elf/riscv.h (RISCV_GP_SYMBOL): New define.
bfd/ChangeLog:
2017-04-03 Palmer Dabbelt <palmer@dabbelt.com>
* elfnn-riscv.c (GP_NAME): Delete.
(riscv_global_pointer_value): Change GP_NAME to RISCV_GP_SYMBOL.
(_bfd_riscv_relax_lui): Likewise.
opcodes/ChangeLog:
2017-04-03 Palmer Dabbelt <palmer@dabbelt.com>
* riscv-dis.c (riscv_disassemble_insn): Change "_gp" to
RISCV_GP_SYMBOL.
|
|
2017-03-27 Andrew Waterman <andrew@sifive.com>
* opcode/riscv-opc.h (CSR_PMPCFG0): New define.
(CSR_PMPCFG1): Likewise.
(CSR_PMPCFG2): Likewise.
(CSR_PMPCFG3): Likewise.
(CSR_PMPADDR0): Likewise.
(CSR_PMPADDR1): Likewise.
(CSR_PMPADDR2): Likewise.
(CSR_PMPADDR3): Likewise.
(CSR_PMPADDR4): Likewise.
(CSR_PMPADDR5): Likewise.
(CSR_PMPADDR6): Likewise.
(CSR_PMPADDR7): Likewise.
(CSR_PMPADDR8): Likewise.
(CSR_PMPADDR9): Likewise.
(CSR_PMPADDR10): Likewise.
(CSR_PMPADDR11): Likewise.
(CSR_PMPADDR12): Likewise.
(CSR_PMPADDR13): Likewise.
(CSR_PMPADDR14): Likewise.
(CSR_PMPADDR15): Likewise.
(pmpcfg0): Declare register.
(pmpcfg1): Likewise.
(pmpcfg2): Likewise.
(pmpcfg3): Likewise.
(pmpaddr0): Likewise.
(pmpaddr1): Likewise.
(pmpaddr2): Likewise.
(pmpaddr3): Likewise.
(pmpaddr4): Likewise.
(pmpaddr5): Likewise.
(pmpaddr6): Likewise.
(pmpaddr7): Likewise.
(pmpaddr8): Likewise.
(pmpaddr9): Likewise.
(pmpaddr10): Likewise.
(pmpaddr11): Likewise.
(pmpaddr12): Likewise.
(pmpaddr13): Likewise.
(pmpaddr14): Likewise.
(pmpaddr15): Likewise.
|
|
gas and the binutils.
binutils * readelf.c: Add support for wasm32 ELF format WebAssembly files.
(guess_is_rela): Likewise.
(dump_relocations): Likewise.
(is_32bit_abs_reloc): Likewise.
(is_none_reloc_): Likewise.
* NEWS: Mention the new support.
* testsuite/lib/binutils-common.exp (is_elf_format): Mark wasm32
as ELF target.
(supports_gnu_unique): Mark wasm32 as supporting STB_GNU_UNIQUE.
* testsuite/binutils-all/nm.exp: Mark wasm32 as requiring .size annotations.
* testsuite/binutils-all/wasm32: New directory.
* testsuite/binutils-all/wasm32/create-wasm.d: New file.
* testsuite/binutils-all/wasm32/create-wasm.s: Likewise.
* testsuite/binutils-all/wasm32/custom-section.d: Likewise.
* testsuite/binutils-all/wasm32/custom-section.s: Likewise.
* testsuite/binutils-all/wasm32/invalid-wasm-1.d: Likewise.
* testsuite/binutils-all/wasm32/invalid-wasm-1.s: Likewise.
* testsuite/binutils-all/wasm32/long-sections.d: Likewise.
* testsuite/binutils-all/wasm32/long-sections.s: Likewise.
* testsuite/binutils-all/wasm32/parse-wasm.d: Likewise.
* testsuite/binutils-all/wasm32/parse-wasm.s: Likewise.
* testsuite/binutils-all/wasm32/parse-wasm-2.d: Likewise.
* testsuite/binutils-all/wasm32/parse-wasm-2.s: Likewise.
* testsuite/binutils-all/wasm32/prepared-section.d: Likewise.
* testsuite/binutils-all/wasm32/prepared-section.s: Likewise.
* testsuite/binutils-all/wasm32/wasm32.exp: New file, run tests.
gas * config/tc-wasm32.h: New file: Add WebAssembly assembler target.
* config/tc-wasm32.c: New file: Add WebAssembly assembler target.
* Makefile.am: Add WebAssembly assembler target.
* configure.tgt: Add WebAssembly assembler target.
* doc/c-wasm32.texi: New file: Start documenting WebAssembly
assembler.
* doc/all.texi: Define WASM32.
* doc/as.texinfo: Add WebAssembly entries.
* NEWS: Mention the new support.
* Makefile.in: Regenerate.
* po/gas.pot: Regenerate.
* po/POTFILES.in: Regenerate.
* testsuite/gas/wasm32: New directory.
* testsuite/gas/wasm32/allinsn.d: New file.
* testsuite/gas/wasm32/allinsn.s: New file.
* testsuite/gas/wasm32/illegal.l: New file.
* testsuite/gas/wasm32/illegal.s: New file.
* testsuite/gas/wasm32/illegal-2.l: New file.
* testsuite/gas/wasm32/illegal-2.s: New file.
* testsuite/gas/wasm32/illegal-3.l: New file.
* testsuite/gas/wasm32/illegal-3.s: New file.
* testsuite/gas/wasm32/illegal-4.l: New file.
* testsuite/gas/wasm32/illegal-4.s: New file.
* testsuite/gas/wasm32/illegal-5.l: New file.
* testsuite/gas/wasm32/illegal-5.s: New file.
* testsuite/gas/wasm32/illegal-6.l: New file.
* testsuite/gas/wasm32/illegal-6.s: New file.
* testsuite/gas/wasm32/illegal-7.l: New file.
* testsuite/gas/wasm32/illegal-7.s: New file.
* testsuite/gas/wasm32/illegal-8.l: New file.
* testsuite/gas/wasm32/illegal-8.s: New file.
* testsuite/gas/wasm32/illegal-9.l: New file.
* testsuite/gas/wasm32/illegal-9.s: New file.
* testsuite/gas/wasm32/illegal-10.l: New file.
* testsuite/gas/wasm32/illegal-10.s: New file.
* testsuite/gas/wasm32/illegal-11.l: New file.
* testsuite/gas/wasm32/illegal-11.s: New file.
* testsuite/gas/wasm32/illegal-12.l: New file.
* testsuite/gas/wasm32/illegal-12.s: New file.
* testsuite/gas/wasm32/illegal-13.l: New file.
* testsuite/gas/wasm32/illegal-13.s: New file.
* testsuite/gas/wasm32/illegal-14.l: New file.
* testsuite/gas/wasm32/illegal-14.s: New file.
* testsuite/gas/wasm32/illegal-15.l: New file.
* testsuite/gas/wasm32/illegal-15.s: New file.
* testsuite/gas/wasm32/illegal-16.l: New file.
* testsuite/gas/wasm32/illegal-16.s: New file.
* testsuite/gas/wasm32/illegal-17.l: New file.
* testsuite/gas/wasm32/illegal-17.s: New file.
* testsuite/gas/wasm32/illegal-18.l: New file.
* testsuite/gas/wasm32/illegal-18.s: New file.
* testsuite/gas/wasm32/illegal-19.l: New file.
* testsuite/gas/wasm32/illegal-19.s: New file.
* testsuite/gas/wasm32/illegal-20.l: New file.
* testsuite/gas/wasm32/illegal-20.s: New file.
* testsuite/gas/wasm32/illegal-21.l: New file.
* testsuite/gas/wasm32/illegal-21.s: New file.
* testsuite/gas/wasm32/illegal-22.l: New file.
* testsuite/gas/wasm32/illegal-22.s: New file.
* testsuite/gas/wasm32/illegal-24.l: New file.
* testsuite/gas/wasm32/illegal-24.s: New file.
* testsuite/gas/wasm32/illegal-25.l: New file.
* testsuite/gas/wasm32/illegal-25.s: New file.
* testsuite/gas/wasm32/reloc.d: New file.
* testsuite/gas/wasm32/reloc.s: New file.
* testsuite/gas/wasm32/wasm32.exp: New tests for WebAssembly
architecture.
opcodes * configure.ac: Add (empty) bfd_wasm32_arch target.
* configure: Regenerate
* po/opcodes.pot: Regenerate.
include * opcode/wasm.h: New file to support wasm32 architecture.
* elf/wasm32.h: Add R_WASM32_32 relocation.
bfd * elf32-wasm32.c: Add relocation code, two relocs.
* reloc.c: Add wasm32 relocations.
* libbfd.h: Regenerate.
* bfd-in2.h: Regenerate.
* bfd/po/bfd.pot: Regenerate.
|
|
This adds -Mraw for PowerPC objdump, a disassembler option to display
the underlying machine instruction rather than aliases. For example,
"rlwinm" always rather than "rotlwi" when the instruction is
performing a simple rotate.
binutils/
* doc/binutils.texi (objdump): Document PowerPC -M options.
gas/
* config/tc-ppc.c (md_parse_option): Reject -mraw.
include/
* opcode/ppc.h (PPC_OPCODE_RAW): Define.
(PPC_OPCODE_*): Make them all unsigned long long constants.
opcodes/
* ppc-dis.c (ppc_opts): Set PPC_OPCODE_PPC for "any" flags. Add
"raw" option.
(lookup_powerpc): Don't special case -1 dialect. Handle
PPC_OPCODE_RAW.
(print_insn_powerpc): Mask out PPC_OPCODE_ANY on first
lookup_powerpc call, pass it on second.
|
|
include * elf/wasm32.h: New file to support wasm32 architecture.
bfd * cpu-wasm32.c: New file to support wasm32 architecture.
* elf32-wasm32.c: New file to support wasm32 architecture.
* Makefile.am: Add wasm32 architecture.
* archures.c: Likewise.
* config.bfd: Likewise.
* configure.ac: Likewise.
* targets.c: Likewise.
|
|
opcodes * arc-nps400-tbl.h: Add Ultra Ip and Miscellaneous instructions format.
* arc-opc.c: Add defines. e.g. F_NJ, F_NM , F_NO_T, F_NPS_SR, F_NPS_M, F_NPS_CORE, F_NPS_ALL.
(insert_nps_misc_imm_offset): New function.
(extract_nps_misc imm_offset): New function.
(arc_num_flag_operands): Add F_NJ, F_NM, F_NO_T.
(arc_flag_special_cases): Add F_NJ, F_NM, F_NO_T.
include * opcode/arc.h (insn_class_t): Add ULTRAIP and MISC class.
gas * testsuite/gas/arc/nps400-12.s: New file.
* testsuite/gas/arc/nps400-12.d: New file.
|
|
This patch removes the vx2 facility flag. It will not be used by GCC
and was a misnomer anyway.
Committed to mainline and 2.28 branch.
include/ChangeLog:
2017-03-21 Andreas Krebbel <krebbel@linux.vnet.ibm.com>
* opcode/s390.h (S390_INSTR_FLAG_VX2): Remove.
(S390_INSTR_FLAG_FACILITY_MASK): Adjust value.
gas/ChangeLog:
2017-03-21 Andreas Krebbel <krebbel@linux.vnet.ibm.com>
* config/tc-s390.c (s390_parse_cpu): Remove S390_INSTR_FLAG_VX2
from cpu_table. Remove vx2, and novx2 from cpu_flags.
opcodes/ChangeLog:
2017-03-21 Andreas Krebbel <krebbel@linux.vnet.ibm.com>
* s390-mkopc.c (main): Remove vx2 check.
* s390-opc.txt: Remove vx2 instruction flags.
|
|
Instructions for loading or storing 16/32B data from one address type to
another.
gas/ChangeLog
* testsuite/gas/arc/nps400-11.s: New file.
* testsuite/gas/arc/nps400-11.d: New file.
include/ChangeLog
* opcode/arc.h (insn_class_t): Add DMA class.
opcodes/ChangeLog
* arc-nps400-tbl.h: Add cp32/cp16 instructions format.
* arc-opc.c: Add F_NPS_NA, NPS_DMA_IMM_ENTRY, NPS_DMA_IMM_OFFSET.
(insert_nps_imm_offset): New function.
(extract_nps_imm_offset): New function.
(insert_nps_imm_entry): New function.
(extract_nps_imm_entry): New function.
|
|
include * elf/common.h (GNU_BUILD_ATTRIBUTE_SHORT_ENUM): New GNU BUILD
note type.
binutils * readelf.c (print_gnu_build_attribute_name): Add support for
GNU_BUILD_ATTRIBUTE_SHORT_ENUM.
|
|
Sync GCC dwarf.def change
2017-03-14 Jakub Jelinek <jakub@redhat.com>
PR debug/77589
* dwarf2.def (DW_OP_GNU_variable_value): New opcode.
|
|
PR demangler/70909
PR demangler/67264
* cp-demangle.c: Fix endless recursion. Pass
struct demangle_component as non const.
(d_make_empty): Initialize variable.
(d_print_comp_inner): Limit recursion.
(d_print_comp): Decrement variable.
* cp-demint.c (cplus_demangle_fill_component): Initialize
variable.
(cplus_demangle_fill_builtin_type): Likewise.
(cplus_demangle_fill_operator): Likewise.
* testsuite/demangle-expected: Add tests.
|
|
R_AARCH64_TLSDESC_ADD_LO12_NC to R_AARCH64_TLSDESC_ADD_LO12.
PR binutils/21202
include * elf/aarch64.h (R_AARCH64_TLSDESC_LD64_LO12_NC): Rename to
R_AARCH64_TLSDESC_LD64_LO12.
(R_AARCH64_TLSDESC_ADD_LO12_NC): Rename to
R_AARCH64_TLSDESC_ADD_LO12_NC.
bfd * reloc.c (BFD_RELOC_AARCH64_TLSDESC_LD64_LO12_NC): Rename to
BFD_RELOC_AARCH64_TLSDESC_LD64_LO12.
(BFD_RELOC_AARCH64_TLSDESC_ADD_LO12_NC): Rename to
BFD_RELOC_AARCH64_TLSDESC_ADD_LO12.
* bfd-in2.h: Regenerate.
* libbfd.h: Regenerate.
* elfnn-aarch64.c (IS_AARCH64_TLS_RELAX_RELOC): Update reloc
names.
(IS_AARCH64_TLSDESC_RELOC): Likewise.
(elfNN_aarch64_howto_table): Likewise.
(aarch64_tls_transition_without_check): Likewise.
(aarch64_reloc_got_type): Likewise.
(elfNN_aarch64_final_link_relocate): Likewise.
(elfNN_aarch64_tls_relax): Likewise.
(elfNN_aarch64_relocate_section): Likewise.
(elfNN_aarch64_gc_sweep_hook): Likewise.
(elfNN_aarch64_check_relocs): Likewise.
* elfxx-aarch64.c (_bfd_aarch64_elf_put_addend): Likewise.
(_bfd_aarch64_elf_resolve_relocation): Likewise.
gas * config/tc-aarch64.c (reloc_table): Rename
BFD_RELOC_AARCH64_TLSDESC_LD64_LO12_NC to
BFD_RELOC_AARCH64_TLSDESC_LD64_LO12. Rname
BFD_RELOC_AARCH64_TLSDESC_ADD_LO12_NC to
BFD_RELOC_AARCH64_TLSDESC_ADD_LO12.
(md_apply_fix): Likewise.
(aarch64_force_relocation): Likewise.
* testsuite/gas/aarch64/tls.d: Update regexp.
ld * testsuite/ld-aarch64/ifunc-5r-local.d: Update regexp.
|
|
include * elf/common.h (EM_LANAI): New machine number.
(EM_BPF): Likewise.
(EM_WEBASSEMBLY): Likewise.
Move low value, deprecated, numbers to their numerical
equivalents.
binutils * readelf.c (get_machine_name): Rearrange switch table in order of
increasing machine number. Add missing entries.
|
|
Property type and datasz are always 4 bytes for both 32-bit and 64-bit
objects. Property values for GNU_PROPERTY_X86_ISA_1_USED and
GNU_PROPERTY_X86_ISA_1_NEEDED are 4 bytes for both i386 and x86-64
objects. We should also check GNU_PROPERTY_LOPROC and
GNU_PROPERTY_LOUSER.
binutils/
PR binutils/21231
* readelf.c (decode_x86_isa): Change argument to unsigned int.
(print_gnu_property_note): Retrieve property type and datasz as
4-byte integer. Consolidate property datasz check. Check
GNU_PROPERTY_LOPROC and GNU_PROPERTY_LOUSER.
* testsuite/binutils-all/i386/pr21231a.d: New file.
* testsuite/binutils-all/i386/pr21231a.s: Likewise.
* testsuite/binutils-all/i386/pr21231b.d: Likewise.
* testsuite/binutils-all/i386/pr21231b.s: Likewise.
* testsuite/binutils-all/x86-64/pr21231a.d: Likewise.
* testsuite/binutils-all/x86-64/pr21231a.s: Likewise.
* testsuite/binutils-all/x86-64/pr21231b.d: Likewise.
* testsuite/binutils-all/x86-64/pr21231b.s: Likewise.
include/
PR binutils/21231
* elf/common.h (GNU_PROPERTY_LOPROC): New.
(GNU_PROPERTY_HIPROC): Likewise.
(GNU_PROPERTY_LOUSER): Likewise.
(GNU_PROPERTY_HIUSER): Likewise.
|
|
include * elf/common.h (SHF_GNU_BUILD_NOTE): Define.
(NT_GNU_PROPERTY_TYPE_0): Define.
(NT_GNU_BUILD_ATTRIBUTE_OPEN): Define.
(NT_GNU_BUILD_ATTRIBUTE_FUN): Define.
(GNU_BUILD_ATTRIBUTE_TYPE_NUMERIC): Define.
(GNU_BUILD_ATTRIBUTE_TYPE_STRING): Define.
(GNU_BUILD_ATTRIBUTE_TYPE_BOOL_TRUE): Define.
(GNU_BUILD_ATTRIBUTE_TYPE_BOOL_FALSE): Define.
(GNU_BUILD_ATTRIBUTE_VERSION): Define.
(GNU_BUILD_ATTRIBUTE_STACK_PROT): Define.
(GNU_BUILD_ATTRIBUTE_RELRO): Define.
(GNU_BUILD_ATTRIBUTE_STACK_SIZE): Define.
(GNU_BUILD_ATTRIBUTE_TOOL): Define.
(GNU_BUILD_ATTRIBUTE_ABI): Define.
(GNU_BUILD_ATTRIBUTE_PIC): Define.
(NOTE_GNU_PROPERTY_SECTION_NAME): Define.
(GNU_BUILD_ATTRS_SECTION_NAME): Define.
(GNU_PROPERTY_STACK_SIZE): Define.
(GNU_PROPERTY_NO_COPY_ON_PROTECTED): Define.
(GNU_PROPERTY_X86_ISA_1_USED): Define.
(GNU_PROPERTY_X86_ISA_1_NEEDED): Define.
(GNU_PROPERTY_X86_ISA_1_486): Define.
(GNU_PROPERTY_X86_ISA_1_586): Define.
(GNU_PROPERTY_X86_ISA_1_686): Define.
(GNU_PROPERTY_X86_ISA_1_SSE): Define.
(GNU_PROPERTY_X86_ISA_1_SSE2): Define.
(GNU_PROPERTY_X86_ISA_1_SSE3): Define.
(GNU_PROPERTY_X86_ISA_1_SSSE3): Define.
(GNU_PROPERTY_X86_ISA_1_SSE4_1): Define.
(GNU_PROPERTY_X86_ISA_1_SSE4_2): Define.
(GNU_PROPERTY_X86_ISA_1_AVX): Define.
(GNU_PROPERTY_X86_ISA_1_AVX2): Define.
(GNU_PROPERTY_X86_ISA_1_AVX512F): Define.
(GNU_PROPERTY_X86_ISA_1_AVX512CD): Define.
(GNU_PROPERTY_X86_ISA_1_AVX512ER): Define.
(GNU_PROPERTY_X86_ISA_1_AVX512PF): Define.
(GNU_PROPERTY_X86_ISA_1_AVX512VL): Define.
(GNU_PROPERTY_X86_ISA_1_AVX512DQ): Define.
(GNU_PROPERTY_X86_ISA_1_AVX512BW): Define.
binutils* readelf.c (get_note_type): Add support for GNU_BUILD_NOTEs.
(get_gnu_elf_note_type): Add support for GNU_PROPERTY_NOTEs.
(decode_x86_isa): New function.
(print_gnu_property_note): New function.
(print_gnu_note): Handle GNU_PROPERTY_NOTEs.
(print_gnu_build_attribute_description): New function.
(print_gnu_build_attribute_name): New function.
(process_note): Add support for GNU_BUILD_NOTEs.
* objcopy.c (--merge-notes): New command line option.
(copy_options): Add merge-notes.
(copy_usage): Likewise.
(is_merge_note_section): New function.
(merge_gnu_build_notes): New function.
(copy_object): Merge note sections if asked to do so.
(skip_section): Add skip_copy parameter. Add support for skipping
merged note sections.
(copy_relocations_in_section): Update call to skip_section.
(copy_section): Likewise.
(copy_main): Add support for merge-notes option.
* doc/binutils.texi: Document the new option to objcopy.
* NEWS: Mention the new feature.
* testsuite/binutils-all/note-2-32.d: New test. Checks note
merging on 32-bit targets.
* testsuite/binutils-all/note-2-32.s: New test source file.
* testsuite/binutils-all/note-2-64.d: New test. Like note-2-32.d
but for 64-bit targets.
* testsuite/binutils-all/note-2-64.s: New test source file.
* testsuite/binutils-all/objcopy.exp: Run the new test.
|
|
This commit adds support to GDB so that it can modify the disassembler-options
value that is passed to the disassembler, similar to objdump's -M option.
Currently, the only supported targets are ARM, PowerPC and S/390, but
adding support for a new target(s) is not difficult.
include/
* dis-asm.h (disasm_options_t): New typedef.
(parse_arm_disassembler_option): Remove prototype.
(set_arm_regname_option): Likewise.
(get_arm_regnames): Likewise.
(get_arm_regname_num_options): Likewise.
(disassemble_init_s390): New prototype.
(disassembler_options_powerpc): Likewise.
(disassembler_options_arm): Likewise.
(disassembler_options_s390): Likewise.
(remove_whitespace_and_extra_commas): Likewise.
(disassembler_options_cmp): Likewise.
(next_disassembler_option): New inline function.
(FOR_EACH_DISASSEMBLER_OPTION): New macro.
opcodes/
* disassemble.c Include "safe-ctype.h".
(disassemble_init_for_target): Handle s390 init.
(remove_whitespace_and_extra_commas): New function.
(disassembler_options_cmp): Likewise.
* arm-dis.c: Include "libiberty.h".
(NUM_ELEM): Delete.
(regnames): Use long disassembler style names.
Add force-thumb and no-force-thumb options.
(NUM_ARM_REGNAMES): Rename from this...
(NUM_ARM_OPTIONS): ...to this. Use ARRAY_SIZE.
(get_arm_regname_num_options): Delete.
(set_arm_regname_option): Likewise.
(get_arm_regnames): Likewise.
(parse_disassembler_options): Likewise.
(parse_arm_disassembler_option): Rename from this...
(parse_arm_disassembler_options): ...to this. Make static.
Use new FOR_EACH_DISASSEMBLER_OPTION macro to scan over options.
(print_insn): Use parse_arm_disassembler_options.
(disassembler_options_arm): New function.
(print_arm_disassembler_options): Handle updated regnames.
* ppc-dis.c: Include "libiberty.h".
(ppc_opts): Add "32" and "64" entries.
(ppc_parse_cpu): Use ARRAY_SIZE and disassembler_options_cmp.
(powerpc_init_dialect): Add break to switch statement.
Use new FOR_EACH_DISASSEMBLER_OPTION macro.
(disassembler_options_powerpc): New function.
(print_ppc_disassembler_options): Use ARRAY_SIZE.
Remove printing of "32" and "64".
* s390-dis.c: Include "libiberty.h".
(init_flag): Remove unneeded variable.
(struct s390_options_t): New structure type.
(options): New structure.
(init_disasm): Rename from this...
(disassemble_init_s390): ...to this. Add initializations for
current_arch_mask and option_use_insn_len_bits_p. Remove init_flag.
(print_insn_s390): Delete call to init_disasm.
(disassembler_options_s390): New function.
(print_s390_disassembler_options): Print using information from
struct 'options'.
* po/opcodes.pot: Regenerate.
binutils/
* objdump.c (main): Use remove_whitespace_and_extra_commas.
gdb/
* NEWS: Mention new set/show disassembler-options commands.
* doc/gdb.texinfo: Document new set/show disassembler-options commands.
* disasm.c: Include "arch-utils.h", "gdbcmd.h" and "safe-ctype.h".
(prospective_options): New static variable.
(gdb_disassembler::gdb_disassembler): Initialize
m_di.disassembler_options.
(gdb_buffered_insn_length_init_dis): Initilize di->disassembler_options.
(get_disassembler_options): New function.
(set_disassembler_options): Likewise.
(set_disassembler_options_sfunc): Likewise.
(show_disassembler_options_sfunc): Likewise.
(disassembler_options_completer): Likewise.
(_initialize_disasm): Likewise.
* disasm.h (get_disassembler_options): New prototype.
(set_disassembler_options): Likewise.
* gdbarch.sh (gdbarch_disassembler_options): New variable.
(gdbarch_verify_disassembler_options): Likewise.
* gdbarch.c: Regenerate.
* gdbarch.h: Likewise.
* arm-tdep.c (num_disassembly_options): Delete.
(set_disassembly_style): Likewise.
(arm_disassembler_options): New static variable.
(set_disassembly_style_sfunc): Convert short style name into long
option name. Call set_disassembler_options.
(show_disassembly_style_sfunc): New function.
(arm_gdbarch_init): Call set_gdbarch_disassembler_options and
set_gdbarch_verify_disassembler_options.
(_initialize_arm_tdep): Delete regnames variable and update callers.
(arm_disassembler_options): Initialize.
(disasm_options): New variable.
(num_disassembly_options): Rename from this...
(num_disassembly_styles): ...to this. Compute by scanning through
disasm_options.
(valid_disassembly_styles): Initialize using disasm_options.
Remove calls to parse_arm_disassembler_option, get_arm_regnames and
set_arm_regname_option.
Pass show_disassembly_style_sfunc to the "disassembler" setshow command.
* rs6000-tdep.c (powerpc_disassembler_options): New static variable.
(rs6000_gdbarch_init): Call set_gdbarch_disassembler_options and
set_gdbarch_verify_disassembler_options.
* s390-tdep.c (s390_disassembler_options): New static variable.
(s390_gdbarch_init):all set_gdbarch_disassembler_options and
set_gdbarch_verify_disassembler_options.
gdb/testsuite/
* gdb.arch/powerpc-power.exp: Delete test.
* gdb.arch/powerpc-power.s: Likewise.
* gdb.disasm/disassembler-options.exp: New test.
* gdb.arch/powerpc-altivec.exp: Likewise.
* gdb.arch/powerpc-altivec.s: Likewise.
* gdb.arch/powerpc-altivec2.exp: Likewise.
* gdb.arch/powerpc-altivec2.s: Likewise.
* gdb.arch/powerpc-altivec3.exp: Likewise.
* gdb.arch/powerpc-altivec3.s: Likewise.
* gdb.arch/powerpc-power7.exp: Likewise.
* gdb.arch/powerpc-power7.s: Likewise.
* gdb.arch/powerpc-power8.exp: Likewise.
* gdb.arch/powerpc-power8.s: Likewise.
* gdb.arch/powerpc-power9.exp: Likewise.
* gdb.arch/powerpc-power9.s: Likewise.
* gdb.arch/powerpc-vsx.exp: Likewise.
* gdb.arch/powerpc-vsx.s: Likewise.
* gdb.arch/powerpc-vsx2.exp: Likewise.
* gdb.arch/powerpc-vsx2.s: Likewise.
* gdb.arch/powerpc-vsx3.exp: Likewise.
* gdb.arch/powerpc-vsx3.s: Likewise.
* gdb.arch/arm-disassembler-options.exp: Likewise.
* gdb.arch/powerpc-disassembler-options.exp: Likewise.
* gdb.arch/s390-disassembler-options.exp: Likewise.
|
|
This came up because I was looking at ld/tmpdir/addpcis.o and noticed
the odd addends on REL16DX_HA. They ought to both be -4. The error
crept in due REL16DX_HA howto being pc-relative (as indeed it should
be), and code at gas/write.c:1001 after this comment
/* Make it pc-relative. If the back-end code has not
selected a pc-relative reloc, cancel the adjustment
we do later on all pc-relative relocs. */
*not* cancelling the pc-relative adjustment. So I've made a dummy
non-relative split reloc so that the generic code handles this, rather
than attempting to add hacks later in md_apply_fix which would not be
very robust. Having the new internal reloc also makes it easy to
support
addpcis rx,sym@ha
as an equivalent to
addpcis rx,(sym-0f)@ha
0:
The patch also fixes overflow checking, which must test whether the
addi will overflow too since @l relocs don't have any overflow check.
Lastly, since I was poking at md_apply_fix, I arranged to have the
generic gas/write.c code emit errors for subtraction expressions where
we lack reloc support.
include/
* elf/ppc64.h (R_PPC64_16DX_HA): New. Expand fake reloc comment.
* elf/ppc.h (R_PPC_16DX_HA): Likewise.
bfd/
* reloc.c (BFD_RELOC_PPC_16DX_HA): New.
* elf64-ppc.c (ppc64_elf_howto_raw <R_PPC64_16DX_HA>): New howto.
(ppc64_elf_reloc_type_lookup): Translate new bfd reloc.
(ppc64_elf_ha_reloc): Correct overflow test on REL16DX_HA.
(ppc64_elf_relocate_section): Likewise.
* elf32-ppc.c (ppc_elf_howto_raw <R_PPC_16DX_HA>): New howto.
(ppc_elf_reloc_type_lookup): Translate new bfd reloc.
(ppc_elf_check_relocs): Handle R_PPC_16DX_HA to pacify gcc.
* libbfd.h: Regenerate.
* bfd-in2.h: Regenerate.
gas/
* config/tc-ppc.c (md_assemble): Use BFD_RELOC_PPC_16DX_HA for addpcis.
(md_apply_fix): Remove fx_subsy check. Move code converting to
pcrel reloc earlier and handle BFD_RELOC_PPC_16DX_HA. Remove code
emiiting errors on seeing fx_pcrel set on unexpected relocs, as
that is done now by the generic code via..
* config/tc-ppc.h (TC_FORCE_RELOCATION_SUB_LOCAL): ..this. Define.
(TC_VALIDATE_FIX_SUB): Define.
ld/
* testsuite/ld-powerpc/addpcis.d: Define ext1 and ext2 at
limits of addpcis range.
|
|
This patch supports some additions to the SVE architecture prior to
its public release.
include/
* opcode/aarch64.h (AARCH64_OPND_SVE_ADDR_RI_S4x16)
(AARCH64_OPND_SVE_IMM_ROT1, AARCH64_OPND_SVE_IMM_ROT2)
(AARCH64_OPND_SVE_Zm3_INDEX, AARCH64_OPND_SVE_Zm3_22_INDEX)
(AARCH64_OPND_SVE_Zm4_INDEX): New aarch64_opnds.
opcodes/
* aarch64-tbl.h (OP_SVE_HMH, OP_SVE_VMU_HSD, OP_SVE_VMVU_HSD)
(OP_SVE_VMVV_HSD, OP_SVE_VMVVU_HSD, OP_SVE_VM_HSD, OP_SVE_VUVV_HSD)
(OP_SVE_VUV_HSD, OP_SVE_VU_HSD, OP_SVE_VVVU_H, OP_SVE_VVVU_S)
(OP_SVE_VVVU_HSD, OP_SVE_VVV_D, OP_SVE_VVV_D_H, OP_SVE_VVV_H)
(OP_SVE_VVV_HSD, OP_SVE_VVV_S, OP_SVE_VVV_S_B, OP_SVE_VVV_SD_BH)
(OP_SVE_VV_BHSDQ, OP_SVE_VV_HSD, OP_SVE_VZVV_HSD, OP_SVE_VZV_HSD)
(OP_SVE_V_HSD): New macros.
(OP_SVE_VMU_SD, OP_SVE_VMVU_SD, OP_SVE_VM_SD, OP_SVE_VUVV_SD)
(OP_SVE_VU_SD, OP_SVE_VVVU_SD, OP_SVE_VVV_SD, OP_SVE_VZVV_SD)
(OP_SVE_VZV_SD, OP_SVE_V_SD): Delete.
(aarch64_opcode_table): Add new SVE instructions.
(aarch64_opcode_table): Use imm_rotate{1,2} instead of imm_rotate
for rotation operands. Add new SVE operands.
* aarch64-asm.h (ins_sve_addr_ri_s4): New inserter.
(ins_sve_quad_index): Likewise.
(ins_imm_rotate): Split into...
(ins_imm_rotate1, ins_imm_rotate2): ...these two inserters.
* aarch64-asm.c (aarch64_ins_imm_rotate): Split into...
(aarch64_ins_imm_rotate1, aarch64_ins_imm_rotate2): ...these two
functions.
(aarch64_ins_sve_addr_ri_s4): New function.
(aarch64_ins_sve_quad_index): Likewise.
(do_misc_encoding): Handle "MOV Zn.Q, Qm".
* aarch64-asm-2.c: Regenerate.
* aarch64-dis.h (ext_sve_addr_ri_s4): New extractor.
(ext_sve_quad_index): Likewise.
(ext_imm_rotate): Split into...
(ext_imm_rotate1, ext_imm_rotate2): ...these two extractors.
* aarch64-dis.c (aarch64_ext_imm_rotate): Split into...
(aarch64_ext_imm_rotate1, aarch64_ext_imm_rotate2): ...these two
functions.
(aarch64_ext_sve_addr_ri_s4): New function.
(aarch64_ext_sve_quad_index): Likewise.
(aarch64_ext_sve_index): Allow quad indices.
(do_misc_decoding): Likewise.
* aarch64-dis-2.c: Regenerate.
* aarch64-opc.h (FLD_SVE_i3h, FLD_SVE_rot1, FLD_SVE_rot2): New
aarch64_field_kinds.
(OPD_F_OD_MASK): Widen by one bit.
(OPD_F_NO_ZR): Bump accordingly.
(get_operand_field_width): New function.
* aarch64-opc.c (fields): Add new SVE fields.
(operand_general_constraint_met_p): Handle new SVE operands.
(aarch64_print_operand): Likewise.
* aarch64-opc-2.c: Regenerate.
gas/
* doc/c-aarch64.texi: Document that sve implies fp16, simd and compnum.
* config/tc-aarch64.c (parse_vector_type_for_operand): Allow .q
to be used with SVE registers.
(parse_operands): Handle new SVE operands.
(aarch64_features): Make "sve" require F16 rather than FP. Also
require COMPNUM.
* testsuite/gas/aarch64/sve.s: Add tests for new instructions.
Include compnum tests.
* testsuite/gas/aarch64/sve.d: Update accordingly.
* testsuite/gas/aarch64/sve-invalid.s: Add tests for new instructions.
* testsuite/gas/aarch64/sve-invalid.l: Update accordingly. Also
update expected output for new FMOV and MOV alternatives.
|
|
This patch adds a named "compnum" feature for the ARMv8.3-A FCADD
and FCMLA extensions.
include/
* opcode/aarch64.h (AARCH64_FEATURE_COMPNUM): New macro.
(AARCH64_ARCH_V8_3): Include AARCH64_FEATURE_COMPNUM.
opcodes/
* aarch64-tbl.h (aarch64_feature_simd_v8_3): Replace with...
(aarch64_feature_compnum): ...this.
(SIMD_V8_3): Replace with...
(COMPNUM): ...this.
(CNUM_INSN): New macro.
(aarch64_opcode_table): Use it for the complex number instructions.
gas/
* doc/c-aarch64.texi: Add a "compnum" entry.
* config/tc-aarch64.c (aarch64_features): Likewise,
* testsuite/gas/aarch64/advsimd-compnum.s: New test.
* testsuite/gas/aarch64/advsimd-compnum.d: Likewise.
|
|
include/ChangeLog:
2017-02-22 Andrew Waterman <andrew@sifive.com>
* opcode/riscv-opc.h (CSR_SCOUNTEREN): New define.
(CSR_MCOUNTEREN): Likewise.
(scounteren): Declare register.
(mcounteren): Likewise.
|
|
This adds support of new instructions to the S/390 specific parts.
The important feature of the new instruction set is the support of
single and extended precision floating point vector operations.
Note: arch12 is NOT the official name of the new CPU. It just
continues the series of archXX options supported as alternate names.
The archXX terminology refers to the edition number of the Principle
of Operations manual. The official CPU name will be added later while
keeping support of the arch12 for backwards compatibility.
No testsuite regressions.
Committed to mainline.
Bye,
-Andreas-
opcodes/ChangeLog:
2017-02-23 Andreas Krebbel <krebbel@linux.vnet.ibm.com>
* s390-mkopc.c (main): Accept arch12 as cpu string and vx2 as
facility.
* s390-opc.c: Add new operand description macros, new instruction
types, instruction masks, and new .insn instruction types.
* s390-opc.txt: Add new arch12 instructions.
include/ChangeLog:
2017-02-23 Andreas Krebbel <krebbel@linux.vnet.ibm.com>
* opcode/s390.h (enum s390_opcode_cpu_val): New value
S390_OPCODE_ARCH12.
(S390_INSTR_FLAG_VX2): New macro definition.
gas/ChangeLog:
2017-02-23 Andreas Krebbel <krebbel@linux.vnet.ibm.com>
* config/tc-s390.c (s390_parse_cpu): New entry for arch12.
* doc/as.texinfo: Document arch12 as cpu type.
* doc/c-s390.texi: Likewise.
* testsuite/gas/s390/s390.exp: Run arch12 specific tests.
* testsuite/gas/s390/zarch-arch12.d: New test.
* testsuite/gas/s390/zarch-arch12.s: New test.
* testsuite/gas/s390/zarch-z13.d: Rename some mnemonics in the
output patterns.
|
|
With this change an architecture level bump due to assembly ASIs will show
up as a warning/error depending on options passed to gas.
Tested with sparc64-linux-gnu, and it does not introduce any regressions.
gas/ChangeLog:
Add support for associating SPARC ASIs with an architecture level.
* config/tc-sparc.c (parse_sparc_asi): New encode SPARC ASIs.
opcodes/ChangeLog:
Add support for associating SPARC ASIs with an architecture level.
* include/opcode/sparc.h (sparc_asi): New sparc_asi struct.
* opcodes/sparc-opc.c (asi_table): Updated asi_table and encoding/
decoding of SPARC ASIs.
|
|
include/ChangeLog:
2017-02-14 Andrew Waterman <andrew@sifive.com>
* opcode/riscv-opc.h (MATCH_SFENCE_VMA): New define.
(MASK_SFENCE_VMA): Likewise.
(sfence_vma): Declare instruction.
opcodes/ChangeLog:
2017-02-14 Andrew Waterman <andrew@sifive.com>
* riscv-opc.c (riscv_opcodes): Add sfence.vma instruction and
pseudoinstructions.
|
|
This stops powerpc gas blithely accepting such nonsense as
"addi %f4,%cr3,%r31".
PR 21118
gas/
* NEWS: Mention powerpc register checks.
* config/tc-ppc.c (struct pd_reg): Make value a short. Add flags.
(pre_defined_registers): Delete fpscr and pmr entries. Set
register type in flags.
(cr_names): Set type in flags.
(reg_name_search): Return pointer to struct pd_reg rather than value.
(register_name): Adjust to suit. Set X_md from flags.
(ppc_parse_name): Likewise.
(ppc_optimize_expr): New function.
(md_assemble): Verify expresion reg flags match operand.
* config/tc-ppc.h (md_optimize_expr): Define.
(ppc_optimize_expr): Declare.
include/
* opcode/ppc.h (PPC_OPERAND_*): Reassign values, regs first.
(PPC_OPERAND_SPR, PPC_OPERAND_GQR): Define.
opcodes/
* ppc-opc.c (powerpc_operands): Flag SPR, SPRG and TBR entries
with PPC_OPERAND_SPR. Flag PSQ and PSQM with PPC_OPERAND_GQR.
|
|
gas/
2017-02-06 Claudiu Zissulescu <claziss@synopsys.com>
* config/tc-arc.c (parse_opcode_flags): Ignore implicit flags.
include/
2017-02-06 Claudiu Zissulescu <claziss@synopsys.com>
Anton Kolesov <anton.kolesov@synopsys.com>
* opcode/arc.h (insn_class_t): Add ENTER, LEAVE, POP, PUSH, BBIT0,
BBIT1, BI, BIH, BRCC, EI, JLI, and SUB instruction classes.
(flag_class_t): Add F_CLASS_WB, F_CLASS_ZZ, and F_CLASS_IMPLICIT
flag classes.
opcode/
2017-02-06 Claudiu Zissulescu <claziss@synopsys.com>
Anton Kolesov <anton.kolesov@synopsys.com>
* arc-dis.c (arc_disassemble_info): New structure.
(init_arc_disasm_info): New function.
(find_format_from_table): Ignore implicit flags.
(find_format): Update dissassembler private data.
(print_flags): Likewise.
(print_insn_arc): Likewise.
(arc_opcode_to_insn_type): Consider the new added instruction
classes.
(arcAnalyzeInstr): Remove.
(arc_insn_decode): New function.
* arc-dis.h (arc_ldst_writeback_mode): New enum.
(arc_ldst_data_size): Likewise.
(arc_condition_code): Likewise.
(arc_operand_kind): Likewise.
(arc_insn_kind): New struct.
(arc_instruction): Likewise.
(arc_insn_decode): Declare function.
(ARC_Debugger_OperandType): Deleted.
(Flow): Likewise.
(NullifyMode): Likewise.
(allOperandsSize): Likewise.
(arcDisState): Likewise.
(arcAnalyzeInstr): Likewise.
* arc-dis.c (arc_opcode_to_insn_type): Handle newly introduced
insn_class_t enums.
* arc-opc.c (F_SIZED): New define.
(C_CC_EQ, C_CC_GE, C_CC_GT, C_CC_HI, C_CC_HS): Likewise.
(C_CC_LE, C_CC_LO, C_CC_LS, C_CC_LT, C_CC_NE): Likewise.
(C_CC_NE, C_AA_AB, C_AA_AW, C_ZZ_D, C_ZZ_H, C_ZZ_B): Likewise.
(arc_flag_classes): Add F_CLASS_COND/F_CLASS_IMPLICIT flags.
* opcodes/arc-tbl.h: Update instructions to include new
F_CLASS_IMPLICIT flags.
(bbit0, lp): Change class.
(bbit1, bi, bih, br*, ei_s, jli_s): Likewsie
|
|
include/ChangeLog:
2017-01-25 Dimitar Dimitrov <dimitar@dinux.eu>
* opcode/hppa.h: Clarify that file is part of GNU opcodes.
* opcode/i860.h: Ditto.
* opcode/nios2.h: Ditto.
* opcode/nios2r1.h: Ditto.
* opcode/nios2r2.h: Ditto.
* opcode/pru.h: Ditto.
opcodes/ChangeLog:
2017-01-25 Dimitar Dimitrov <dimitar@dinux.eu>
* pru-opc.c: Remove vague reference to a future GDB port.
|
|
Add missing <> around name.
|
|
* elf/common.h (NT_ARM_SVE): Define.
|
|
include/
* dwarf2.def: Sync with mainline gcc sources.
|
|
The weaker release consistency support of ARMv8.3-A is allowed as an optional
extension for ARMv8.2-A, so separate command line option and feature flag is
added: -march=armv8.2-a+rcpc turns LDAPR, LDAPRB, LDAPRH instructions on.
opcodes/
* aarch64-tbl.h (RCPC, RCPC_INSN): Define.
(aarch64_opcode_table): Use RCPC_INSN.
include/
* opcode/aarch64.h (AARCH64_FEATURE_RCPC): Define.
(AARCH64_ARCH_V8_3): Update.
gas/
* config/tc-aarch64.c (aarch64_features): Add rcpc.
* doc/c-aarch64.texi (AArch64 Extensions): Document rcpc.
* testsuite/gas/aarch64/ldst-exclusive-armv8_3.d: Rename to ...
* testsuite/gas/aarch64/ldst-rcpc.d: This.
* testsuite/gas/aarch64/ldst-exclusive-armv8_3.s: Rename to ...
* testsuite/gas/aarch64/ldst-rcpc.s: This.
* testsuite/gas/aarch64/ldst-rcpc-armv8_2.d: New test.
|
|
gas * config/tc-riscv.c (riscv_set_arch): Whitelist the "q" ISA
extension.
(riscv_after_parse_args): Set FLOAT_ABI_QUAD when the Q ISA is
enabled and no other ABI is specified.
include * opcode/riscv-opc.h: Add support for the "q" ISA extension.
opcodes * riscv-opc.c (riscv-opcodes): Add support for the "q" ISA
extension.
* riscv-opcodes/all-opcodes: Likewise.
|
|
* dwarf2.def: Sync with mainline gcc sources
* dwarf2.h: Likewise.
2016-12-21 Jakub Jelinek <jakub@redhat.com>
* dwarf2.def (DW_FORM_ref_sup): Renamed to ...
(DW_FORM_ref_sup4): ... this. New form.
(DW_FORM_ref_sup8): New form.
2016-10-17 Jakub Jelinek <jakub@redhat.com>
* dwarf2.h (enum dwarf_calling_convention): Add new DWARF5
calling convention codes.
(enum dwarf_line_number_content_type): New.
(enum dwarf_location_list_entry_type): Add DWARF5 DW_LLE_*
codes.
(enum dwarf_source_language): Add new DWARF5 DW_LANG_* codes.
(enum dwarf_macro_record_type): Add DWARF5 DW_MACRO_* codes.
(enum dwarf_name_index_attribute): New.
(enum dwarf_range_list_entry): New.
(enum dwarf_unit_type): New.
* dwarf2.def: Add new DWARF5 DW_TAG_*, DW_FORM_*, DW_AT_*,
DW_OP_* and DW_ATE_* entries.
2016-08-15 Jakub Jelinek <jakub@redhat.com>
* dwarf2.def (DW_AT_string_length_bit_size,
DW_AT_string_length_byte_size): New attributes.
2016-08-12 Alexandre Oliva <aoliva@redhat.com>
PR debug/63240
* dwarf2.def (DW_AT_deleted, DW_AT_defaulted): New.
* dwarf2.h (enum dwarf_defaulted_attribute): New.
|
|
|
|
|
|
This applies the second part of GDB's End of Year Procedure, which
updates the copyright year range in all of GDB's files.
gdb/ChangeLog:
Update copyright year range in all GDB files.
|
