1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
|
/*
* U-Boot - Configuration file for BlackStamp board
* Configuration by Ben Matthews for UR LLE using bf533-stamp.h
* as a template
* See http://blackfin.uclinux.org/gf/project/blackstamp/
*/
#ifndef __CONFIG_BLACKSTAMP_H__
#define __CONFIG_BLACKSTAMP_H__
#include <asm/config-pre.h>
/*
* Debugging: Set these options if you're having problems
*/
/*
* #define CONFIG_DEBUG_EARLY_SERIAL
* #define DEBUG
* #define CONFIG_DEBUG_DUMP
* #define CONFIG_DEBUG_DUMP_SYMS
*/
#define CONFIG_PANIC_HANG 0
/* CPU Options
* Be sure to set the Silicon Revision Correctly
*/
#define CONFIG_BFIN_CPU bf532-0.5
#define CONFIG_BFIN_BOOT_MODE BFIN_BOOT_SPI_MASTER
/*
* Board settings
*/
#define CONFIG_SMC91111 1
#define CONFIG_SMC91111_BASE 0x20300300
/* FLASH/ETHERNET uses the same address range
* Depending on what you have the CPLD doing
* this probably isn't needed
*/
#define SHARED_RESOURCES 1
/* Is I2C bit-banged? */
/*
* Clock Settings
* CCLK = (CLKIN * VCO_MULT) / CCLK_DIV
* SCLK = (CLKIN * VCO_MULT) / SCLK_DIV
*/
/* CONFIG_CLKIN_HZ is any value in Hz */
#define CONFIG_CLKIN_HZ 25000000
/* CLKIN_HALF controls the DF bit in PLL_CTL 0 = CLKIN */
/* 1 = CLKIN / 2 */
#define CONFIG_CLKIN_HALF 0
/* PLL_BYPASS controls the BYPASS bit in PLL_CTL 0 = do not bypass */
/* 1 = bypass PLL */
#define CONFIG_PLL_BYPASS 0
/* VCO_MULT controls the MSEL (multiplier) bits in PLL_CTL */
/* Values can range from 0-63 (where 0 means 64) */
#define CONFIG_VCO_MULT 16
/* CCLK_DIV controls the core clock divider */
/* Values can be 1, 2, 4, or 8 ONLY */
#define CONFIG_CCLK_DIV 1
/* SCLK_DIV controls the system clock divider */
/* Values can range from 1-15 */
#define CONFIG_SCLK_DIV 3
/*
* Network settings
*/
#ifdef CONFIG_SMC91111
#define CONFIG_IPADDR 192.168.0.15
#define CONFIG_NETMASK 255.255.255.0
#define CONFIG_GATEWAYIP 192.168.0.1
#define CONFIG_SERVERIP 192.168.0.2
#define CONFIG_HOSTNAME blackstamp
#define CONFIG_ROOTPATH "/checkout/uClinux-dist/romfs"
#define CONFIG_SYS_AUTOLOAD "no"
#endif
#define CONFIG_ENV_IS_IN_SPI_FLASH
#define CONFIG_ENV_OFFSET 0x40000
#define CONFIG_ENV_SIZE 0x2000
#define CONFIG_ENV_SECT_SIZE 0x40000
/*
* SDRAM settings & memory map
*/
#define CONFIG_MEM_SIZE 64 /* 128, 64, 32, 16 */
#define CONFIG_MEM_ADD_WDTH 10 /* 8, 9, 10, 11 */
#define CONFIG_SYS_MONITOR_LEN (256 << 10)
#define CONFIG_SYS_MALLOC_LEN (384 << 10)
/*
* Command settings
*/
#define CONFIG_SYS_LONGHELP 1
#define CONFIG_CMDLINE_EDITING 1
#define CONFIG_AUTO_COMPLETE 1
#define CONFIG_ENV_OVERWRITE 1
#ifdef CONFIG_SMC91111
# define CONFIG_CMD_DHCP
# define CONFIG_CMD_PING
#else
#endif
#ifdef CONFIG_SYS_I2C_SOFT
# define CONFIG_CMD_I2C
#endif
#define CONFIG_CMD_BOOTLDR
#define CONFIG_CMD_CACHE
#define CONFIG_CMD_CPLBINFO
#define CONFIG_CMD_DATE
#define CONFIG_CMD_SF
#define CONFIG_BOOTDELAY 5
#define CONFIG_BOOTCOMMAND "run ramboot"
#define CONFIG_BOOTARGS \
"root=/dev/mtdblock0 rw " \
"clkin_hz=" __stringify(CONFIG_CLKIN_HZ) " " \
"earlyprintk=" \
"serial," \
"uart" __stringify(CONFIG_UART_CONSOLE) "," \
__stringify(CONFIG_BAUDRATE) " " \
"console=ttyBF0," __stringify(CONFIG_BAUDRATE)
#if defined(CONFIG_CMD_NET)
# if (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_BYPASS)
# define UBOOT_ENV_FILE "u-boot.bin"
# else
# define UBOOT_ENV_FILE "u-boot.ldr"
# endif
# if (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_SPI_MASTER)
# ifdef CONFIG_SPI
# define UBOOT_ENV_UPDATE \
"eeprom write $(loadaddr) 0x0 $(filesize)"
# else
# define UBOOT_ENV_UPDATE \
"sf probe " __stringify(BFIN_BOOT_SPI_SSEL) ";" \
"sf erase 0 0x40000;" \
"sf write $(loadaddr) 0 $(filesize)"
# endif
# else
# define UBOOT_ENV_UPDATE \
"protect off 0x20000000 0x2003FFFF;" \
"erase 0x20000000 0x2003FFFF;" \
"cp.b $(loadaddr) 0x20000000 $(filesize)"
# endif
# define NETWORK_ENV_SETTINGS \
"ubootfile=" UBOOT_ENV_FILE "\0" \
"update=" \
"tftp $(loadaddr) $(ubootfile);" \
UBOOT_ENV_UPDATE \
"\0" \
"addip=set bootargs $(bootargs) " \
"ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):" \
"$(hostname):eth0:off" \
"\0" \
"ramargs=set bootargs " CONFIG_BOOTARGS "\0" \
"ramboot=" \
"tftp $(loadaddr) uImage;" \
"run ramargs;" \
"run addip;" \
"bootm" \
"\0" \
"nfsargs=set bootargs " \
"root=/dev/nfs rw " \
"nfsroot=$(serverip):$(rootpath),tcp,nfsvers=3" \
"\0" \
"nfsboot=" \
"tftp $(loadaddr) vmImage;" \
"run nfsargs;" \
"run addip;" \
"bootm" \
"\0"
#else
# define NETWORK_ENV_SETTINGS
#endif
/*
* Console settings
*/
#define CONFIG_BAUDRATE 57600
#define CONFIG_LOADS_ECHO 1
#define CONFIG_UART_CONSOLE 0
#define CONFIG_BFIN_SERIAL
/*
* I2C settings
* By default PF2 is used as SDA and PF3 as SCL on the Stamp board
* Located on the expansion connector on pins 86/85
* Note these pins are arbitrarily chosen because we aren't using
* them yet. You can (and probably should) change these values!
*/
#ifdef CONFIG_SYS_I2C_SOFT
#define CONFIG_SOFT_I2C_GPIO_SCL GPIO_PF9
#define CONFIG_SOFT_I2C_GPIO_SDA GPIO_PF8
#define CONFIG_SYS_I2C_SOFT_SPEED 50000
#define CONFIG_SYS_I2C_SOFT_SLAVE 0xFE
#endif
/*
* Miscellaneous configurable options
*/
#define CONFIG_RTC_BFIN 1
/*
* Serial Flash Infomation
*/
#define CONFIG_BFIN_SPI
/* For the M25P64 SCK Should be Kept < 15Mhz */
#define CONFIG_ENV_SPI_MAX_HZ 15000000
#define CONFIG_SF_DEFAULT_SPEED 15000000
/*
* FLASH organization and environment definitions
*/
#define CONFIG_EBIU_AMGCTL_VAL 0xFF
#define CONFIG_EBIU_AMBCTL0_VAL 0xBBC3BBC3
#define CONFIG_EBIU_AMBCTL1_VAL 0x99B39983
#define CONFIG_EBIU_SDRRC_VAL 0x268
#define CONFIG_EBIU_SDGCTL_VAL 0x911109
/* Even though Rev C boards have Parallel Flash
* We aren't supporting it. Newer versions of the
* hardware don't support Parallel Flash at all.
*/
#define CONFIG_SYS_NO_FLASH
#undef CONFIG_CMD_JFFS2
#endif
|
