1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
|
// SPDX-License-Identifier: GPL-2.0+
/*
* Copyright (C) 2020 Linumiz
* Author: Parthiban Nallathambi <parthiban@linumiz.com>
*/
#include <init.h>
#include <asm/arch/clock.h>
#include <asm/arch/crm_regs.h>
#include <asm/arch/mx6-pins.h>
#include <asm/arch/sys_proto.h>
#include <asm/global_data.h>
#include <asm/mach-imx/iomux-v3.h>
#include <asm/mach-imx/mxc_i2c.h>
#include <fsl_esdhc_imx.h>
#include <linux/bitops.h>
#include <miiphy.h>
#include <netdev.h>
#include <usb.h>
#include <usb/ehci-ci.h>
DECLARE_GLOBAL_DATA_PTR;
int dram_init(void)
{
gd->ram_size = get_ram_size((void *)PHYS_SDRAM, PHYS_SDRAM_SIZE);
return 0;
}
#define UART_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \
PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \
PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST | \
PAD_CTL_HYS)
static iomux_v3_cfg_t const uart1_pads[] = {
MX6_PAD_UART1_TX_DATA__UART1_DCE_TX | MUX_PAD_CTRL(UART_PAD_CTRL),
MX6_PAD_UART1_RX_DATA__UART1_DCE_RX | MUX_PAD_CTRL(UART_PAD_CTRL),
};
static iomux_v3_cfg_t const uart5_pads[] = {
MX6_PAD_UART5_TX_DATA__UART5_DCE_TX | MUX_PAD_CTRL(UART_PAD_CTRL),
MX6_PAD_UART5_RX_DATA__UART5_DCE_RX | MUX_PAD_CTRL(UART_PAD_CTRL),
MX6_PAD_GPIO1_IO09__UART5_DCE_CTS | MUX_PAD_CTRL(UART_PAD_CTRL),
MX6_PAD_GPIO1_IO08__UART5_DCE_RTS | MUX_PAD_CTRL(UART_PAD_CTRL),
};
static void setup_iomux_uart(void)
{
imx_iomux_v3_setup_multiple_pads(uart1_pads, ARRAY_SIZE(uart1_pads));
imx_iomux_v3_setup_multiple_pads(uart5_pads, ARRAY_SIZE(uart5_pads));
}
#ifdef CONFIG_FEC_MXC
static int setup_fec(void)
{
struct iomuxc *const iomuxc_regs = (struct iomuxc *)IOMUXC_BASE_ADDR;
int ret;
/*
* Use 50M anatop loopback REF_CLK1 for ENET1,
* clear gpr1[13], set gpr1[17].
*/
clrsetbits_le32(&iomuxc_regs->gpr[1], IOMUX_GPR1_FEC1_MASK,
IOMUX_GPR1_FEC1_CLOCK_MUX1_SEL_MASK);
ret = enable_fec_anatop_clock(0, ENET_50MHZ);
if (ret)
return ret;
enable_enet_clk(1);
return 0;
}
int board_phy_config(struct phy_device *phydev)
{
/*
* Defaults + Enable status LEDs (LED1: Activity, LED0: Link) & select
* 50 MHz RMII clock mode.
*/
phy_write(phydev, MDIO_DEVAD_NONE, 0x1f, 0x8190);
if (phydev->drv->config)
phydev->drv->config(phydev);
return 0;
}
#endif /* CONFIG_FEC_MXC */
int board_early_init_f(void)
{
setup_iomux_uart();
return 0;
}
int board_init(void)
{
/* Address of boot parameters */
gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
#ifdef CONFIG_FEC_MXC
setup_fec();
#endif
return 0;
}
int checkboard(void)
{
u32 cpurev = get_cpu_rev();
printf("Board: MYiR MYS-6ULX %s Single Board Computer\n",
get_imx_type((cpurev & 0xFF000) >> 12));
return 0;
}
|
