Age | Commit message (Collapse) | Author | Files | Lines |
|
The way all of the memory init code here works is that we pass
0xDEADBEEF around for the initial value (as it's a well known 'poison'
value and so easily recognized in debuggers, etc). The only point of
this CONFIG symbol was to pass in a different value for that purpose.
Drop this symbol and cleanup the code slightly.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
This removes the following unreferenced CONFIG symbols:
CONFIG_FDTADDR
CONFIG_FDTFILE
CONFIG_FLASH_SECTOR_SIZE
CONFIG_FSL_CPLD
CONFIG_HDMI_ENCODER_I2C_ADDR
CONFIG_I2C_MVTWSI
CONFIG_I2C_RTC_ADDR
CONFIG_IRAM_END
CONFIG_IRAM_SIZE
CONFIG_KSNET_MDIO_PHY_CONFIG_ENABLE
CONFIG_L1_INIT_RAM
CONFIG_MACB_SEARCH_PHY
CONFIG_MIU_2BIT_21_7_INTERLEAVED
CONFIG_MTD_NAND_VERIFY_WRITE
CONFIG_MVGBE_PORTS
CONFIG_NETDEV
CONFIG_NUM_DSP_CPUS
CONFIG_PHY_BASE_ADR
CONFIG_PHY_INTERFACE_MODE
CONFIG_PSRAM_SCFG
CONFIG_RAMBOOT_SPIFLASH
CONFIG_RAMBOOT_TEXT_BASE
CONFIG_RD_LVL
CONFIG_ROCKCHIP_SDHCI_MAX_FREQ
CONFIG_SETUP_INITRD_TAG
CONFIG_SH_QSPI_BASE
CONFIG_SMDK5420
CONFIG_SOCRATES
CONFIG_SPI_ADDR
CONFIG_SPI_FLASH_QUAD
CONFIG_SPI_FLASH_SIZE
CONFIG_SPI_HALF_DUPLEX
CONFIG_SPI_N25Q256A_RESET
CONFIG_TEGRA_SLINK_CTRLS
CONFIG_TPM_TIS_BASE_ADDRESS
CONFIG_UBOOT_SECTOR_COUNT
CONFIG_UBOOT_SECTOR_START
CONFIG_VAR_SIZE_SPL
CONFIG_VERY_BIG_RAM
And also:
BL1_SIZE
PHY_NO
RESERVE_BLOCK_SIZE
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
The rest of the unmigrated CONFIG symbols in the CONFIG_SYS namespace do
not easily transition to Kconfig. In many cases they likely should come
from the device tree instead. Move these out of CONFIG namespace and in
to CFG namespace.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
This commit removes the following unused symbols:
CONFIG_SYS_NVRAM_BASE_ADDR
CONFIG_SYS_NVRAM_SIZE
CONFIG_SYS_PAXE_BASE
CONFIG_SYS_PCCNT
CONFIG_SYS_PCDAT
CONFIG_SYS_PCDDR
CONFIG_SYS_PCI1_ADDR
CONFIG_SYS_PCI2_ADDR
CONFIG_SYS_PCI1_IO_BUS
CONFIG_SYS_PCI1_IO_SIZE
CONFIG_SYS_PCI1_MEM_BUS
CONFIG_SYS_PCI1_MEM_SIZE
CONFIG_SYS_PCIE3_ADDR
CONFIG_SYS_PCIE4_ADDR
CONFIG_SYS_PCIE3_IO_PHYS
CONFIG_SYS_PCIE3_IO_VIRT
CONFIG_SYS_PCIE4_IO_PHYS
CONFIG_SYS_PCIE4_IO_VIRT
CONFIG_SYS_PLL_SETTLING_TIME
CONFIG_SYS_QMAN_CENA_BASE
CONFIG_SYS_QMAN_SP_CENA_SIZE
CONFIG_SYS_RCAR_I2C0_BASE
CONFIG_SYS_RCAR_I2C1_BASE
CONFIG_SYS_RCAR_I2C2_BASE
CONFIG_SYS_RCAR_I2C3_BASE
CONFIG_SYS_SATA
CONFIG_SYS_SDRAM_BASE2
CONFIG_SYS_SGMII_REFCLK_MHZ
CONFIG_SYS_SGMII_LINERATE_MHZ
CONFIG_SYS_SGMII_RATESCALE
CONFIG_SYS_SH_SDHI0_BASE
CONFIG_SYS_SH_SDHI0_BASE
CONFIG_SYS_SH_SDHI1_BASE
CONFIG_SYS_SH_SDHI2_BASE
CONFIG_SYS_SH_SDHI3_BASE
CONFIG_SYS_SPI_ST_ENABLE_WP_PIN
CONFIG_SYS_SPI_U_BOOT_SIZE
CONFIG_SYS_VCXK_ACKNOWLEDGE_DDR
CONFIG_SYS_VCXK_ACKNOWLEDGE_PIN
CONFIG_SYS_VCXK_ACKNOWLEDGE_PORT
CONFIG_SYS_VCXK_BASE
CONFIG_SYS_VCXK_DEFAULT_LINEALIGN
CONFIG_SYS_VCXK_DOUBLEBUFFERED
CONFIG_SYS_VCXK_ENABLE_DDR
CONFIG_SYS_VCXK_ENABLE_PIN
CONFIG_SYS_VCXK_ENABLE_PORT
CONFIG_SYS_VCXK_INVERT_DDR
CONFIG_SYS_VCXK_INVERT_PIN
CONFIG_SYS_VCXK_INVERT_PORT
CONFIG_SYS_VCXK_REQUEST_DDR
CONFIG_SYS_VCXK_REQUEST_PIN
CONFIG_SYS_VCXK_REQUEST_PORT
CONFIG_SYS_VSC7385_BR_PRELIM
CONFIG_SYS_VSC7385_OR_PRELIM
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
The rest of the unmigrated CONFIG symbols in the CONFIG_SYS_NOR
namespace do not easily transition to Kconfig. In many cases they likely
should come from the device tree instead. Move these out of CONFIG
namespace and in to CFG namespace.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
The rest of the unmigrated CONFIG symbols in the CONFIG_SYS_NAND
namespace do not easily transition to Kconfig. In many cases they likely
should come from the device tree instead. Move these out of CONFIG
namespace and in to CFG namespace.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
This converts the following to Kconfig:
CONFIG_SYS_MAX_NAND_DEVICE
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
This converts the following to Kconfig:
CONFIG_SYS_I2C_EEPROM_CCID
CONFIG_SYS_I2C_EEPROM_NXID
CONFIG_SYS_EEPROM_BUS_NUM
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
This converts the following to Kconfig:
CONFIG_SYS_MAX_FLASH_SECT
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
This converts the following to Kconfig:
CONFIG_SYS_FLASH_ERASE_TOUT
CONFIG_SYS_FLASH_LOCK_TOUT
CONFIG_SYS_FLASH_UNLOCK_TOUT
CONFIG_SYS_FLASH_WRITE_TOUT
In practice, for two m68k platforms we move to hard-coding with a
comment the timeout values, rather than try and make convoluted Kconfig
logic. We add options for the write and erase options to the pic32
flash driver, as this driver does make use of them. Everywhere else
these are unreferenced values.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
This converts the following to Kconfig:
CONFIG_SYS_FLASH_EMPTY_INFO
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
This converts the following to Kconfig:
CONFIG_LAYERSCAPE_NS_ACCESS
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
This converts the following to Kconfig:
CONFIG_SYS_SPD_BUS_NUM
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
- Make all users of CUSTOM_SYS_INIT_SP_ADDR reference SYS_INIT_SP_ADDR
- Introduce HAS_CUSTOM_SYS_INIT_SP_ADDR to allow for setting the stack
pointer directly, otherwise we use the common calculation.
- On some platforms that were using the standard calculation but did not
set CONFIG_SYS_INIT_RAM_SIZE / CONFIG_SYS_INIT_RAM_ADDR, set them.
- On a small number of platforms that were not subtracting
GENERATED_GBL_DATA_SIZE do so now via the standard calculation.
- CONFIG_SYS_INIT_SP_OFFSET is now widely unused, so remove it from most
board config header files.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
This converts the following to Kconfig:
CONFIG_SPL_PAD_TO
CONFIG_SPL_MAX_SIZE
CONFIG_TPL_PAD_TO
CONFIG_TPL_MAX_SIZE
Note that we need to make TPL_MAX_SIZE be hex, and so move and convert the
existing places.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
This converts the following to Kconfig:
CONFIG_FSL_QIXIS
CONFIG_QIXIS_I2C_ACCESS
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
This converts the following to Kconfig:
CONFIG_DIMM_SLOTS_PER_CTLR
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
This converts the following to Kconfig:
CONFIG_SYS_MONITOR_BASE
Note that for how this is re-used on some PowePC platforms, we introduce
CONFIG_SPL_SYS_MONITOR_BASE and CONFIG_TPL_SYS_MONITOR_BASE and use the
CONFIG_VAL macro to get the correct value at build time, in the code.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
This converts the following to Kconfig:
CONFIG_LPUART
CONFIG_LPUART_32B_REG
And note that CONFIG_LPUART_32B_REG is unused in code.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
This converts the following to Kconfig:
CONFIG_CHIP_SELECTS_PER_CTRL
Cc: Alison Wang <alison.wang@nxp.com>
Cc: Pramod Kumar <pramod.kumar_1@nxp.com>
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Cc: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Cc: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
This converts the following to Kconfig:
CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
This converts the following to Kconfig:
CONFIG_SCSI_AHCI_PLAT
CONFIG_SYS_SCSI_MAX_SCSI_ID
CONFIG_SYS_SCSI_MAX_LUN
CONFIG_SYS_SATA_MAX_DEVICE
Drop CONFIG_SCSI for everything except the sandbox build. We only need
one build for tests.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
|
|
This is defined based on two other CONFIGs for all boards except sandbox
and durian.
For sandbox the value does not matter. For durian the value seems
excessive.
Drop the option completely, to simplify configuration and reduce the
number of things we need to convert to Kconfig.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
|
|
Use moveconfig.py script to convert define CONFIG_SYS_MAX_FLASH_BANKS
and CONFIG_SYS_MAX_FLASH_BANKS_DETECT to Kconfig and move these entries
to defconfigs.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
[trini: Re-switch to IS_ENABLED check in spi-nor-core.c, re-run migration]
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
In order to finish moving this symbol to Kconfig for all platforms, we
need to do a few more things. First, for all platforms that define this
to a function, introduce CONFIG_DYNAMIC_SYS_CLK_FREQ, similar to
CONFIG_DYNAMIC_DDR_CLK_FREQ and populate clock_legacy.h. This entails
also switching all users from CONFIG_SYS_CLK_FREQ to get_board_sys_clk()
and updating a few preprocessor tests.
With that done, all platforms that define a value here can be converted
to Kconfig, and a fall-back of zero is sufficiently safe to use (and
what is used today in cases where code may or may not have this
available). Make sure that code which calls this function includes
<clock_legacy.h> to get the prototype.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
This converts the following to Kconfig:
CONFIG_VID
CONFIG_VOL_MONITOR_INA220
CONFIG_VOL_MONITOR_IR36021_READ
CONFIG_VOL_MONITOR_IR36021_SET
CONFIG_VOL_MONITOR_LTC3882_READ
CONFIG_VOL_MONITOR_LTC3882_SET
To finish this migration, we first need to introduce CONFIG_SPL_VID as
some platforms only use this code in full U-Boot while others use it in
SPL as well. To make the Kconfig logic clearer, guard all of the
sub-options with a if VID || SPL_VID check. Finally, add Kconfig
options for the remaining related options that did not previously have
one.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
This converts the following to Kconfig:
CONFIG_SYS_HZ
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
This converts the following to Kconfig:
CONFIG_SYS_NAND_U_BOOT_LOCATIONS
CONFIG_SYS_NAND_U_BOOT_OFFS
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
This converts the following to Kconfig:
CONFIG_NAND_FSL_ELBC
CONFIG_NAND_FSL_IFC
Note that a number of PowerPC platforms had previously enabled
CONFIG_NAND_FSL_ELBC without CONFIG_MTD_RAW_NAND, and now they no longer
enable the option, reducing the size of a few functions.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
This converts the following to Kconfig:
CONFIG_SYS_NAND_ONFI_DETECTION
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
This converts the following to Kconfig:
CONFIG_SPL_NAND_LOAD
CONFIG_SYS_NAND_BLOCK_SIZE
CONFIG_SYS_NAND_PAGE_SIZE
CONFIG_SYS_NAND_OOBSIZE
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
With the exceptions of ds109, ds414, icnova-a20-swac, nokia_rx51 and
stemmy, disable ATAG support. A large number of platforms had enabled
support but never supported a kernel so old as to require it. Further,
some platforms are old enough to support both, but are well supported by
devicetree booting, and have been for a number of years. This is
because some of the ATAGs related functions have been re-used to provide
the same kind of information, but for devicetree or just generally to
inform the user. When needed still, rename these functions to
get_board_revision() instead, to avoid conflicts. In other cases, these
functions were simply unused, so drop them.
Cc: Andre Przywara <andre.przywara@arm.com>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Phil Sutter <phil@nwl.cc>
Cc: Stefan Bosch <stefan_b@posteo.net>
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
This converts the following to Kconfig:
CONFIG_SKIP_LOWLEVEL_INIT
CONFIG_SKIP_LOWLEVEL_INIT_ONLY
In order to do this, we need to introduce SPL and TPL variants of these
options so that we can clearly disable these options only in SPL in some
cases, and both instances in other cases.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
This converts the following to Kconfig:
CONFIG_RAMBOOT_PBL
CONFIG_SYS_FSL_PBL_PBI
CONFIG_SYS_FSL_PBL_RCW
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
- Guard most of the options in drivers/ddr/fsl/Kconfig with
SYS_FSL_DDR || SYS_FSL_MMDC.
- Migrate FSL_DMA, DDR_ECC, DDR_ECC_CMD, and ECC_INIT_VIA_DDRCONTROLLER
to Kconfig.
- Clean up the logic for including the DDR_ECC_CMD code.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
As this symbol can either be a fixed value or the function
get_board_ddr_clk, migration is tricky. Introduce a choice of DYNAMIC
or STATIC_DDR_CLK_FREQ. If DYNAMIC, we continue to use the board
defined get_board_ddr_clk function. If STATIC, set CONFIG_DDR_CLK_FREQ
to that value and now include/clock_legacy.h contains the function
prototype or defines get_board_ddr_clk() to that static value. Update
callers to test for DYNAMIC or STATIC.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Convert SYS_I2C_EARLY_INIT to Kconfig, and make it depend on
SPL_SYS_I2C_LEGACY. Remove the weak implementation as it's either
something that needs to exist for real, or shouldn't be called.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
- Rename usages of CONFIG_SYS_DEF_EEPROM_ADDR to CONFIG_SYS_I2C_EEPROM_ADDR
based on current usage.
- Convert CONFIG_SYS_I2C_EEPROM_ADDR, CONFIG_SYS_I2C_EEPROM_ADDR_LEN,
CONFIG_SYS_I2C_EEPROM_BUS, CONFIG_CONFIG_SYS_EEPROM_SIZE
CONFIG_SYS_EEPROM_PAGE_WRITE_BITS and CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS
to Kconfig. We move these symbols around a bit and add appropriate
dependencies to them. In some cases, we now add a correct default value
as well.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
This converts the following to Kconfig:
CONFIG_ID_EEPROM
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
This converts the following to Kconfig:
CONFIG_SYS_MMC_ENV_DEV
CONFIG_SYS_MMC_ENV_PART
Note that with this conversion we now have consistent behavior with
respect to ensuring that we have always selected the correct MMC
device and hardware partition.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
This converts the following to Kconfig:
CONFIG_ENV_OVERWRITE
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Rerun migration, remove some comments]
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Move CONFIG_FSL_QSPI to the board defconfigs and while at it also move
CONFIG_SPI_FLASH_SPANSION for LS1043AQDS.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
|
|
Some of these options are not used by the driver anymore and some of
them are obsolete as the information is gathered from the dt. Also
consolidating defines in common headers.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
|
|
Move below defines which are used by mtest utility to Kconfig.
CONFIG_SYS_MEMTEST_START
CONFIG_SYS_MEMTEST_END
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
[trini: Fix kmcoge5ne board, re-run migration as well]
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
This converts the following to Kconfig:
CONFIG_PHYLIB
CONFIG_BITBANGMII
CONFIG_MV88E6352_SWITCH
CONFIG_MV88E61XX_SWITCH
CONFIG_PHYLIB_10G
CONFIG_PHY_AQUANTIA
CONFIG_PHY_ATHEROS
CONFIG_PHY_BROADCOM
CONFIG_PHY_CORTINA
CONFIG_PHY_DAVICOM
CONFIG_PHY_ET1011C
CONFIG_PHY_LXT
CONFIG_PHY_MARVELL
CONFIG_PHY_MICREL
CONFIG_PHY_NATSEMI
CONFIG_PHY_REALTEK
CONFIG_RTL8211X_PHY_FORCE_MASTER
CONFIG_PHY_SMSC
CONFIG_PHY_TERANETICS
CONFIG_PHY_TI
CONFIG_PHY_VITESSE
CONFIG_PHY_XILINX
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
- In ARMv8 NXP Layerscape platforms we also need to make use of
CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so.
- On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define
to 0.
- Add Kconfig entry for ENV_ADDR.
- Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it.
- Add ENV_xxx_REDUND options that depend on their primary option and
SYS_REDUNDAND_ENVIRONMENT
- On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR
for the pre-main-U-Boot environment location.
- On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but
rather it being non-zero, as it will now be zero by default.
- Rework the env_offset absolute in env/embedded.o to not use
CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within
ENV_IS_IN_FLASH.
- Migrate all platforms.
Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: uboot-stm32@st-md-mailman.stormreply.com
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
|
|
Move CONFIG_FSL_QSPI from header file to defconfigs,
consequently unset imply config(CONFIG_SPI_FLASH_BAR) which
is not valid for LS series.
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
|
|
Move the main symbol for Freescale Fman Ethernet controller option to
Kconfig. Also migrate the CONFIG_SYS_QE_FMAN_FW_IN_xxx macros and
rename the SPIFLASH one to follow the same format as all of the others.
To do this fully we need to migrate CONFIG_QC, do so.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Moves below DDR specific defines to Kconfig:
CONFIG_FSL_DDR_BIST
CONFIG_FSL_DDR_FIRST_SLOT_QUAD_CAPABLE
CONFIG_FSL_DDR_INTERACTIVE
CONFIG_FSL_DDR_SYNC_REFRESH
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
|
|
TFABOOT support includes:
- ls1043aqds_tfa_defconfig to be loaded by trusted firmware
- environment address and size changes for TFABOOT
- define BOOTCOMMAND for TFABOOT
Signed-off-by: Pankit Garg <pankit.garg@nxp.com>
Signed-off-by: Vinitha V Pillai <vinitha.pillai@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|