Age | Commit message (Collapse) | Author | Files | Lines |
|
Drop all duplicate newlines. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
|
|
We don't set many options in the board Kconfig entry file but instead
use defconfigs, select in some cases on the target itself, or update the
"default" options of the main entries when needed. In this case we can
remove most of the board Kconfig entries and just add them to the
defconfig like other platforms.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Marek Mojík <marek.mojik@nic.cz> says:
Hello all,
this is a continuation of previous work by Pali to add support for the
Turris 1.x board. As the patches were based on u-boot v2022.04, a
nontrivial rebasing was needed.
Some notes:
- Some options that are in SD defconfig are disabled in NOR defconfig
because over the years u-boot grew and the old NOR defconfig will not
fit into NOR memory.
- SD boot with RAM larger than 2GB will only allocate 2GB of RAM (We
were not able to fix this yet)
|
|
Add support for CZ.NIC Turris 1.x routers.
CZ.NIC Turris 1.0 (RTRS01) and 1.1 (RTRS02) are open source routers, they
have dual-core PowerPC Freescale P2020 CPU and are based on reference
Freescale P2020RDB-PC-A board design.
Hardware design is fully open source, all firmware and hardware design
files are available at Turris project website:
https://docs.turris.cz/hw/turris-1x/turris-1x/
https://project.turris.cz/en/hardware.html
The P2020 BootROM can load U-Boot either from NOR flash or from SD card.
We add the new defconfigs, turris_1x_nor_defconfig, which configures
U-Boot for building the NOR image, and turris_1x_sdcard_defconfig, which
configures U-Boot for building an image suitable for SD card.
The defconfig for NOR image is stripped-down a - many config options
enabled in SD defconfig are disabled for NOR defconfig. This is because
U-Boot grew non-trivially in the last two years and it would not fit
into the space allocated for U-Boot in the NOR memory. In the future we
may try to use LTO to reduce the size of the code and enable more
options.
The design of CZ.NIC Turris 1.x routers is based on Freescale P2020RDB-PC-A
board, so some code from boards/freescale/p1_p2_rdb_pc is used and linked
into Turris 1.x board code.
Turris 1.x code in this patch uses modern distroboot and can boot Linux
kernel from various locations, including NAND, SD card, USB flash disks,
NVMe disks or SATA disks (connected to extra SATA/SCSI PCIe controllers).
Via distroboot is implemented also rescue NOR boot for factory recovery,
triggered by reset button, like on other existing Turris routers.
SD boot with RAM larger than 2GB will only allocate 2GB of RAM (We were
not able to fix this yet)
[ Because various CONFIG_ macros were migrated to Kconfig since the last
time this worked on upstream U-Boot (in 2022), a non-trivial rebasing
was needed and some issues were solved. ]
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Mojík <marek.mojik@nic.cz>
Reviewed-by: Marek Behún <kabel@kernel.org>
|
|
include/asm/config.h
Use the CONFIG_IS_ENABLED() macro when checking for DM_SERIAL so that
CFG_SYS_NS16550_CLK is not defined as get_serial_clock() in SPL if SPL
does not have DM_SERIAL enabled.
Signed-off-by: Marek Mojík <marek.mojik@nic.cz>
Reviewed-by: Marek Behún <kabel@kernel.org>
|
|
Use CONFIG_VAL() for SYS_MONITOR_BASE in start.S so that correct value
is used for SPL.
Signed-off-by: Marek Mojík <marek.mojik@nic.cz>
Reviewed-by: Marek Behún <kabel@kernel.org>
|
|
The find_law() function searches for LAW just by physical address. This
is unsuitable for cases with overlapping LAWs. Extend it to
find_law_by_addr_id(), which searches for LAW by physical address and
target id.
Add a static inline definition of the original find_law() into fsl_law.h
header.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Mojík <marek.mojik@nic.cz>
Reviewed-by: Marek Behún <kabel@kernel.org>
|
|
Add the old invalidate_icache_all function that prints a warning that
was previously found in cmd/cache.c
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Implement a weak default version of flush_dcache_all which is based on
the ARM default, which is to flush the entire range via
flush_dcache_range(...).
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Nothing in-tree calls watchdog_reset() anymore (that stopped two years
ago with the removal of the WATCHDOG_RESET macro). So that function is
dead code.
That was the only caller of reset_85xx_watchdog(), so that
can obviously also be removed.
Finally, init_85xx_watchdog() is/was also not called from anywhere, so
that can go away as well, which nicely also removes a bit of
arch-specific code from the generic watchdog.h header.
Cc: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Stefan Roese <sr@denx.de>
|
|
There is no longer any code in tree that calls a watchdog_reset()
function. The macro WATCHDOG_RESET, which used to emit a call to
watchdog_reset(), got removed two years ago.
Cc: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Stefan Roese <sr@denx.de>
|
|
As part of bringing the master branch back in to next, we need to allow
for all of these changes to exist here.
Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
When bringing in the series 'arm: dts: am62-beagleplay: Fix Beagleplay
Ethernet"' I failed to notice that b4 noticed it was based on next and
so took that as the base commit and merged that part of next to master.
This reverts commit c8ffd1356d42223cbb8c86280a083cc3c93e6426, reversing
changes made to 2ee6f3a5f7550de3599faef9704e166e5dcace35.
Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
This follows the example of RISC-V where <asm/global_data.h> includes
<asm/u-boot.h> directly as "gd" includes a reference to bd_info already
and so the first must include the second anyhow. We then remove
<asm/u-boot.h> from all of the places which include references to "gd"
an so have <asm/global_data.h> already.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Remove <common.h> from all powerpc architecture files and when needed add
missing include files directly. This typically involves using
<asm/u-boot.h> instead due to the difficult nested structure of the
PowerPC includes themselves.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
https://source.denx.de/u-boot/custodians/u-boot-mpc8xx
This pull request adds support for temperature sensors et FPGA loading
on boards from CS GROUP France.
CI: https://source.denx.de/u-boot/custodians/u-boot-mpc8xx/-/pipelines/20416
|
|
enabled""
As reported by Jonas Karlman this series breaks booting on some AArch64
platforms with common use cases. For now the best path forward is to
revert the series.
This reverts commit 777c28460947371ada40868dc994dfe8537d7115, reversing
changes made to ab3453e7b12daef47b9e91da2a2a3d48615dc6fc.
Link: https://lore.kernel.org/u-boot/50dfa3d6-a1ca-4492-a3fc-8d8c56b40b43@kwiboo.se/
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Unlike CMPC885 and CMPCPRO boards, the FPGA of MCR3000 board doesn't
load code automatically but needs to be loaded by software through SPI.
Until now it was loaded later by Linux, but we'd like U-boot to have
access to some information that require the FPGA, like board address
in racks.
So, implemented the load of FPGA in U-boot.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
---
To avoid spamming your email boxes, the code isn't included in
the emailed patch but will be present in the PULL request
|
|
SDMA configuration register needs to be set up only once and doesn't
belong to drivers. Also, the value to be used is different on mpc885.
So do the init in cpu_init_f() with 0x40 for mpc885 and 0x1 for others.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
|
|
All CSSI boards have an LM74 chip as temperature sensor.
Enable it.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
|
|
MCR3000 board has some components tied to the SPI bus, like the Texas
Instruments LM74 temperature sensor.
Add support for SPI bus. The SPI chipselects are a bit special in the
way that they are driven by 3 bits in a register of the board's CPLD
where the value writen in those bits exclusively activates one of the
7 possible chipselects and value 0 sets all chipselets to inactive.
So add a special GPIO driver that simulates GPIOs for those chipselect.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
|
|
When adding additional SPI peripherals, the reg property needs to
be added, and this leads to the following error:
arch/powerpc/dts/cmpc885.dtb: Warning (reg_format): /immr@ff000000/spi@aa0/temp@1:reg: property has invalid length (4 bytes) (#address-cells == 1, #size-cells == 1)
arch/powerpc/dts/cmpc885.dtb: Warning (reg_format): /immr@ff000000/spi@aa0/temp@2:reg: property has invalid length (4 bytes) (#address-cells == 1, #size-cells == 1)
Fix it by removing cell-index and cell-size which is unused and add
reg property. Also fix node name to be in line with reg value.
Also add missing compatible for eeprom node.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
|
|
Simon Glass <sjg@chromium.org> says:
This series is the culmanation of the current line of refactoring
series. It adjusts pxe to call the booting functionality directly
rather than going through the command-line interface.
With this is is possible to boot using the extlinux bootmeth without
the command line enabled.
It also updates fastboot to do a similar thing.
|
|
Allow these functions to be compiled in when CONFIG_BOOTM is enabled,
even if CONFIG_CMD_BOOTM is not.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Angelo Dureghello <angelo@kernel-space.org>
|
|
Simon Glass <sjg@chromium.org> says:
This series continues refactoring the bootm code to allow it to be used
with CONFIG_COMMAND disabled. The OS-handling code is refactored and
a new bootm_run() function is created to run through the bootm stages.
This completes the work.
A booti_go() function is created also, in case it proves useful, but at
last for now standard boot does not use this.
This is cmdd (part d of CMDLINE refactoring)
It depends on dm/bootstda-working
which depends on dm/cmdc-working
|
|
Adjust boot_os_fn to use struct bootm_info instead of the separate
argc, argv and image parameters. Update the handlers accordingly. Few
of the functions make use of the arguments, so this improves code size
slightly.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
The current do_reset() is called from a command context. Add a function
which can be used from anywhere, as is done on ARM.
This is only needed if CONFIG_SYSRESET is disabled.
Since there are lots of reset functions, this one actually just calls
do_reset(). Future refactoring could correct this.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
In most cases, the architecture global data currently makes use of
assorted linux types, but does not include <linux/types.h> to provide
them. Add <linux/types.h> instead of relying on indirect inclusion.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
To quote the author:
This series imports generic versions of ioread_rep/iowrite_rep and
reads/writes from Linux. Some cleanup is done to make sure that all
platforms have proper defines for implemented functions and there are no
redefinitions.
|
|
Add defines for __raw_{read,write}{b,w,l}() functions to make
make asm-generic/io.h aware of them.
Signed-off-by: Igor Prusov <ivprusov@salutedevices.com>
|
|
Remove inclusion of common.h and add relevant
includes when necessary.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
|
|
This file should not include <config.h> nor should it include <common.h>
so remove both.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
In order to not rely on common.h providing a number of common includes,
cleanup what we include directly in order to be able to drop common.h
later.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
In both include/fsl_qe.h and then also remove common.h from the files
which had included fsl_qe.h
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
In matching other architectures that have their global_data.h need to
bring in a types.h header, switch to <linux/types.h> on PowerPC.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
When building a non-SPL image, relocation is needed. This patch restores
the old behaviour before commit b35316fb67cb ("Convert
CONFIG_SPL_INIT_MINIMAL et al to Kconfig") was only defined if
CONFIG_SPL_BUILD was defined.
Fixes: b35316fb67cb ("Convert CONFIG_SPL_INIT_MINIMAL et al to Kconfig")
Signed-off-by: Martin Fäcknitz <faecknitz@hotsplots.de>
|
|
Use the new SPL/TPL/VPL_SYS_MALLOC_F symbols to determine whether the
malloc pool exists.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Sean Anderson <sean.anderson@seco.com>
|
|
It is not a parse error to have a default value of "0" for a "hex" type
entry, instead of "0x0". However, "0" and "0x0" are not treated the
same even by the tools themselves. Correct this by changing the default
value from "0" to "0x0" for all hex type questions that had the
incorrect default. Fix one instance (in two configs) of a default of "0"
being used on a hex question to be "0x0". Remove the cases where a
defconfig had set a value of "0x0" to be used as the default had been
"0".
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
https://source.denx.de/u-boot/custodians/u-boot-fsl-qoriq
Enable DM_SERIAL for T2080RDB, T4240RDB, T1042D4RDB, T1024RDB
|
|
Flushing kernel image after decompression was taking 113 milliseconds
with U-boot 2022.10. With U-boot 2023.01 and 2023.04, flushing
the same amount of memory takes approx 1.5 seconds. With
U-boot 2023.07-rc6, it takes 6.5 seconds.
powerpc flush_cache() function used to call WATCHDOG_RESET() after
flushing every cacheline. At that time WATCHDOG_RESET() was light
so the operation was almost seamless.
But commit 29caf9305b6 ("cyclic: Use schedule() instead of
WATCHDOG_RESET()") replaced WATCHDOG_RESET() by schedule() and that
started to hurt with U-boot 2022.10.
And in U-boot 2023.07-rc6 that's even worse after
commit 26e8ebcd7cb ("watchdog: mpc8xxx: Make it generic").
In the meantime commit 729c1fe656 ("powerpc: introduce
CONFIG_CACHE_FLUSH_WATCHDOG_THRESHOLD") gives us the opportinity to
only call schedule() every given chunk of data instead of every
cacheline. As explained in that commit there is no point in pinging
the watchdog after every cacheline flush, so lets define a sensible
default chunk size of 4k which matches to size of a page on most
powerpc platforms.
With that new default threshold, the culprit flushing performed after
kernel image decompression now takes 85 milliseconds on a powerpc 8xx.
Fixes: 29caf9305b6 ("cyclic: Use schedule() instead of WATCHDOG_RESET()")
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
|
|
Make sure the serial driver is initialized before relocation by tagging
the serial nodes with "bootph-all". Add these u-boot specific properties
to an *-u-boot.dtsi file.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
Add the serial node descriptions similar to Linux v6.4 for the
t1024rdb board and its dependencies.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
Make sure the serial driver is initialized before relocation by tagging
the serial nodes with "bootph-all". Add these u-boot specific properties
to an *-u-boot.dtsi file.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
Add the serial node descriptions similar to Linux v6.4 for the
t1042d4rdb board and its dependencies.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
Make sure the serial driver is initialized before relocation by tagging
the serial nodes with "bootph-all". Add these u-boot specific properties
to an *-u-boot.dtsi file.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
Add the serial node descriptions similar to Linux v6.4 for the t4240rdb
board and its dependencies.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
Make sure the serial driver is initialized before relocation by tagging
the serial nodes with "bootph-all". Add these u-boot specific properties
to an *-u-boot.dtsi file.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
Add the serial node descriptions similar to Linux v6.4 for the t2080rdb
board and its dependencies.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
Powerpc configurations are apparently able to do unaligned accesses. But
in an attempt to clean up and handle unaligned accesses in the same way
we ignore that and use the common asm-generic/unaligned.h directly
instead.
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
|
|
As part of various code clean-ups we have on occasion missed removing
unused header files. None of these files are referenced anywhere else
at this point.
Signed-off-by: Tom Rini <trini@konsulko.com>
|