aboutsummaryrefslogtreecommitdiff
path: root/include
diff options
context:
space:
mode:
Diffstat (limited to 'include')
-rw-r--r--include/commproc.h54
-rw-r--r--include/configs/QS823.h551
-rw-r--r--include/configs/QS850.h551
-rw-r--r--include/configs/QS860T.h390
4 files changed, 0 insertions, 1546 deletions
diff --git a/include/commproc.h b/include/commproc.h
index 29a3e61..5992f11 100644
--- a/include/commproc.h
+++ b/include/commproc.h
@@ -900,60 +900,6 @@ typedef struct scc_enet {
#endif /* CONFIG_NETVIA */
-/*** QS850/QS823 ***************************************************/
-
-#if defined(CONFIG_QS850) || defined(CONFIG_QS823)
-#undef FEC_ENET /* Don't use FEC for EThernet */
-
-#define PROFF_ENET PROFF_SCC2
-#define CPM_CR_ENET CPM_CR_CH_SCC2
-#define SCC_ENET 1
-
-#define PA_ENET_RXD ((ushort)0x0004) /* RXD on PA13 (Pin D9) */
-#define PA_ENET_TXD ((ushort)0x0008) /* TXD on PA12 (Pin D7) */
-#define PC_ENET_RENA ((ushort)0x0080) /* RENA on PC8 (Pin D12) */
-#define PC_ENET_CLSN ((ushort)0x0040) /* CLSN on PC9 (Pin C12) */
-#define PA_ENET_TCLK ((ushort)0x0200) /* TCLK on PA6 (Pin D8) */
-#define PA_ENET_RCLK ((ushort)0x0800) /* RCLK on PA4 (Pin D10) */
-#define PB_ENET_TENA ((uint)0x00002000) /* TENA on PB18 (Pin D11) */
-#define PC_ENET_LBK ((ushort)0x0010) /* Loopback control on PC11 (Pin B14) */
-#define PC_ENET_LI ((ushort)0x0020) /* Link Integrity control PC10 (A15) */
-#define PC_ENET_SQE ((ushort)0x0100) /* SQE Disable control PC7 (B15) */
-
-/* SCC2 TXCLK from CLK2
- * SCC2 RXCLK from CLK4
- * SCC2 Connected to NMSI */
-#define SICR_ENET_MASK ((uint)0x00007F00)
-#define SICR_ENET_CLKRT ((uint)0x00003D00)
-
-#endif /* CONFIG_QS850/QS823 */
-
-/*** QS860T ***************************************************/
-
-#ifdef CONFIG_QS860T
-#ifdef CONFIG_FEC_ENET
-#define FEC_ENET /* use FEC for EThernet */
-#endif /* CONFIG_FEC_ETHERNET */
-
-/* This ENET stuff is for GTH 10 Mbit ( SCC ) */
-#define PROFF_ENET PROFF_SCC1
-#define CPM_CR_ENET CPM_CR_CH_SCC1
-#define SCC_ENET 0
-
-#define PA_ENET_RXD ((ushort)0x0001) /* PA15 */
-#define PA_ENET_TXD ((ushort)0x0002) /* PA14 */
-#define PA_ENET_TCLK ((ushort)0x0800) /* PA4 */
-#define PA_ENET_RCLK ((ushort)0x0200) /* PA6 */
-#define PB_ENET_TENA ((uint)0x00001000) /* PB19 */
-#define PC_ENET_CLSN ((ushort)0x0010) /* PC11 */
-#define PC_ENET_RENA ((ushort)0x0020) /* PC10 */
-
-#define SICR_ENET_MASK ((uint)0x000000ff)
-/* RCLK PA4 -->CLK4, TCLK PA6 -->CLK2 */
-#define SICR_ENET_CLKRT ((uint)0x0000003D)
-
-#endif /* CONFIG_QS860T */
-
/*** RPXLITE ********************************************************/
#ifdef CONFIG_RPXLITE
diff --git a/include/configs/QS823.h b/include/configs/QS823.h
deleted file mode 100644
index 6733460..0000000
--- a/include/configs/QS823.h
+++ /dev/null
@@ -1,551 +0,0 @@
-/*
- * (C) Copyright 2003
- * MuLogic B.V.
- *
- * (C) Copyright 2002
- * Simple Network Magic Corporation
- *
- * (C) Copyright 2000
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-/*
- * board/config.h - configuration options, board specific
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/* various debug settings */
-#undef CONFIG_SYS_DEVICE_NULLDEV /* null device */
-#undef CONFIG_SILENT_CONSOLE /* silent console */
-#undef CONFIG_SYS_CONSOLE_INFO_QUIET /* silent console ? */
-#undef DEBUG_FLASH /* debug flash code */
-#undef FLASH_DEBUG /* debug fash code */
-#undef DEBUG_ENV /* debug environment code */
-
-#define CONFIG_SYS_DIRECT_FLASH_TFTP 1 /* allow direct tftp to flash */
-#define CONFIG_ENV_OVERWRITE 1 /* allow overwrite MAC address */
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-#define CONFIG_MPC823 1 /* This is a MPC823 CPU */
-#define CONFIG_QS823 1 /* ...on a QS823 module */
-#define CONFIG_SCC2_ENET 1 /* SCC2 10BaseT ethernet */
-
-#define CONFIG_SYS_TEXT_BASE 0xFFF00000
-
-/* Select the target clock speed */
-#undef CONFIG_CLOCK_16MHZ /* cpu=16,777,216 Hz, mem=16Mhz */
-#undef CONFIG_CLOCK_33MHZ /* cpu=33,554,432 Hz, mem=33Mhz */
-#undef CONFIG_CLOCK_50MHZ /* cpu=49,971,200 Hz, mem=33Mhz */
-#define CONFIG_CLOCK_66MHZ 1 /* cpu=67,108,864 Hz, mem=66Mhz */
-#undef CONFIG_CLOCK_80MHZ /* cpu=79,986,688 Hz, mem=33Mhz */
-
-#ifdef CONFIG_CLOCK_16MHZ
-#define CONFIG_CLOCK_MULT 512
-#endif
-
-#ifdef CONFIG_CLOCK_33MHZ
-#define CONFIG_CLOCK_MULT 1024
-#endif
-
-#ifdef CONFIG_CLOCK_50MHZ
-#define CONFIG_CLOCK_MULT 1525
-#endif
-
-#ifdef CONFIG_CLOCK_66MHZ
-#define CONFIG_CLOCK_MULT 2048
-#endif
-
-#ifdef CONFIG_CLOCK_80MHZ
-#define CONFIG_CLOCK_MULT 2441
-#endif
-
-/* choose flash size, 4Mb or 8Mb */
-#define CONFIG_FLASH_4MB 1 /* board has 4Mb flash */
-#undef CONFIG_FLASH_8MB /* board has 8Mb flash */
-
-#define CONFIG_CLOCK_BASE 32768 /* Base clock input freq */
-
-#undef CONFIG_8xx_CONS_SMC1
-#define CONFIG_8xx_CONS_SMC2 1 /* Console is on SMC2 */
-#undef CONFIG_8xx_CONS_NONE
-
-#define CONFIG_BAUDRATE 38400 /* console baudrate = 38.4kbps */
-
-#undef CONFIG_CLOCKS_IN_MHZ /* clocks passsed to Linux in MHz */
-
-/* Define default IP addresses */
-#define CONFIG_IPADDR 192.168.1.99 /* own ip address */
-#define CONFIG_SERVERIP 192.168.1.19 /* used for tftp (not nfs?) */
-
-/* message to say directly after booting */
-#define CONFIG_PREBOOT "echo '';" \
- "echo 'type:';" \
- "echo 'run boot_nfs to boot to NFS';" \
- "echo 'run boot_flash to boot to flash';" \
- "echo '';" \
- "echo 'run flash_rootfs to install a new rootfs';" \
- "echo 'run flash_env to clear the env sector';" \
- "echo 'run flash_rw to clear the rw fs';" \
- "echo 'run flash_uboot to install a new u-boot';" \
- "echo 'run flash_kernel to install a new kernel';"
-
-/* wait 5 seconds before executing CONFIG_BOOTCOMMAND */
-#define CONFIG_BOOTDELAY 5
-#define CONFIG_BOOTCOMMAND "run boot_nfs"
-
-#undef CONFIG_BOOTARGS /* made by set_nfs of set_flash */
-
-/* Our flash filesystem looks like this
- *
- * 4Mb board:
- * ffc0 0000 - ffeb ffff root filesystem (jffs2) (~3Mb)
- * ffec 0000 - ffed ffff read-write filesystem (ext2)
- * ffee 0000 - ffef ffff environment
- * fff0 0000 - fff1 ffff u-boot
- * fff2 0000 - ffff ffff linux kernel
- *
- * 8Mb board:
- * ff80 0000 - ffeb ffff root filesystem (jffs2) (~7Mb)
- * ffec 0000 - ffed ffff read-write filesystem (ext2)
- * ffee 0000 - ffef ffff environment
- * fff0 0000 - fff1 ffff u-boot
- * fff2 0000 - ffff ffff linux kernel
- *
- */
-
-/* environment for 4Mb board */
-#ifdef CONFIG_FLASH_4MB
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "serial#=QS823\0" \
- "hostname=qs823\0" \
- "netdev=eth0\0" \
- "ethaddr=00:01:02:B4:36:56\0" \
- "rootpath=/exports/rootfs\0" \
- "mtdparts=mtdparts=phys:2816k(root),128k(rw),128k(env),128k(u-boot),-(kernel)\0" \
- /* fill in variables */ \
- "set_ip=setenv ip ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off\0" \
- "set_nfs=setenv bootargs root=/dev/nfs rw nfsroot=$serverip:$rootpath $ip init=/sbin/init $mtdparts\0" \
- "set_flash=setenv bootargs root=/dev/mtdblock1 ro $ip init=/sbin/init $mtdparts\0" \
- /* commands */ \
- "boot_nfs=run set_ip; run set_nfs; tftp 0x400000 /tftpboot/vmlinux.UBoot; bootm 0x400000\0" \
- "boot_flash=run set_ip; run set_flash; bootm fff20000\0" \
- /* reinstall flash parts */ \
- "flash_rootfs=protect off ffc00000 ffebffff; era ffc00000 ffebffff; tftp ffc00000 /tftpboot/rootfs.jffs2\0" \
- "flash_rw=protect off ffec0000 ffedffff; era ffec0000 ffedffff\0" \
- "flash_env=protect off ffee0000 ffefffff; era ffee0000 ffefffff\0" \
- "flash_uboot=protect off fff00000 fff1ffff; era fff00000 fff1ffff; tftp fff00000 /tftpboot/u-boot.4mb.bin\0" \
- "flash_kernel=protect off fff20000 ffffffff; era fff20000 ffffffff; tftp fff20000 /tftpboot/vmlinux.UBoot\0"
-#endif /* CONFIG_FLASH_4MB */
-
-/* environment for 8Mb board */
-#ifdef CONFIG_FLASH_8MB
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "serial#=QS823\0" \
- "hostname=qs823\0" \
- "netdev=eth0\0" \
- "ethaddr=00:01:02:B4:36:56\0" \
- "rootpath=/exports/rootfs\0" \
- "mtdparts=mtdparts=phys:6912k(root),128k(rw),128k(env),128k(u-boot),-(kernel)\0" \
- /* fill in variables */ \
- "set_ip=setenv ip ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off\0" \
- "set_nfs=setenv bootargs root=/dev/nfs rw nfsroot=$serverip:$rootpath $ip init=/sbin/init $mtdparts\0" \
- "set_flash=setenv bootargs root=/dev/mtdblock1 ro $ip init=/sbin/init $mtdparts\0" \
- /* commands */ \
- "boot_nfs=run set_ip; run set_nfs; tftp 0x400000 /tftpboot/vmlinux.UBoot; bootm 0x400000\0" \
- "boot_flash=run set_ip; run set_flash; bootm fff20000\0" \
- /* reinstall flash parts */ \
- "flash_rootfs=protect off ff800000 ffebffff; era ff800000 ffebffff; tftp ff800000 /tftpboot/rootfs.jffs2\0" \
- "flash_rw=protect off ffec0000 ffedffff; era ffec0000 ffedffff\0" \
- "flash_env=protect off ffee0000 ffefffff; era ffee0000 ffefffff\0" \
- "flash_uboot=protect off fff00000 fff1ffff; era fff00000 fff1ffff; tftp fff00000 /tftpboot/u-boot.8mb.bin\0" \
- "flash_kernel=protect off fff20000 ffffffff; era fff20000 ffffffff; tftp fff20000 /tftpboot/vmlinux.UBoot\0"
-#endif /* CONFIG_FLASH_8MB */
-
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#undef CONFIG_SYS_LOADS_BAUD_CHANGE /* don't allow baudrate change */
-#undef CONFIG_WATCHDOG /* watchdog disabled */
-#undef CONFIG_STATUS_LED /* Status LED disabled */
-#undef CONFIG_CAN_DRIVER /* CAN Driver support disabled */
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_SUBNETMASK
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_BOOTFILESIZE
-
-
-#undef CONFIG_MAC_PARTITION
-#undef CONFIG_DOS_PARTITION
-
-#define CONFIG_RTC_MPC8xx /* use internal RTC of MPC8xx */
-
-
-/*
- * Command line configuration.
- */
-#define CONFIG_CMD_BDI
-#define CONFIG_CMD_BOOTD
-#define CONFIG_CMD_CONSOLE
-#define CONFIG_CMD_DATE
-#define CONFIG_CMD_SAVEENV
-#define CONFIG_CMD_FLASH
-#define CONFIG_CMD_IMI
-#define CONFIG_CMD_IMMAP
-#define CONFIG_CMD_MEMORY
-#define CONFIG_CMD_NET
-#define CONFIG_CMD_RUN
-
-
-/*-----------------------------------------------------------------------
- * Environment variable storage is in FLASH, one sector before U-boot
- */
-#define CONFIG_ENV_IS_IN_FLASH 1
-#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128Kb, one whole sector */
-#define CONFIG_ENV_SIZE 0x2000 /* 8kb */
-#define CONFIG_ENV_ADDR 0xffee0000 /* address of env sector */
-
-/*-----------------------------------------------------------------------
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-
-#define CONFIG_SYS_HUSH_PARSER 1 /* use "hush" command parser */
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-
-#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works */
-#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
-
-#define CONFIG_SYS_LOAD_ADDR 0x400000 /* default load address */
-
-/*-----------------------------------------------------------------------
- * Low Level Configuration Settings
- * (address mappings, register initial values, etc.)
- * You should know what you are doing if you make changes here.
- */
-
-/*-----------------------------------------------------------------------
- * Internal Memory Mapped Register
- */
-#define CONFIG_SYS_IMMR 0xFF000000
-
-/*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area (in DPRAM)
- */
-#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR
-#define CONFIG_SYS_INIT_RAM_SIZE 0x2F00 /* Size of used area in DPRAM */
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- */
-#define CONFIG_SYS_SDRAM_BASE 0x00000000
-#define CONFIG_SYS_FLASH_BASE 0xFF800000 /* Allow an 8Mbyte window */
-
-#define FLASH_BASE0_4M_PRELIM 0xFFC00000 /* Base for 4M Flash */
-#define FLASH_BASE0_8M_PRELIM 0xFF800000 /* Base for 8M Flash */
-
-#define CONFIG_SYS_MONITOR_LEN (192 << 10) /* Reserve 192 kB for Monitor */
-#define CONFIG_SYS_MONITOR_BASE 0xFFF00000 /* U-boot location */
-#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-
-/*-----------------------------------------------------------------------
- * TODO flash parameters
- * FLASH organization for Intel Strataflash
- */
-#undef CONFIG_SYS_FLASH_16BIT /* 32-bit wide flash memory */
-#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 71 /* max number of sectors on one chip */
-
-#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
-
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CONFIG_SYS_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CACHELINE_SHIFT 4 /* log base 2 of the above value */
-#endif
-
-/*-----------------------------------------------------------------------
- * SYPCR - System Protection Control 11-9
- * SYPCR can only be written once after reset!
- *-----------------------------------------------------------------------
- * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
- */
-
-#ifdef CONFIG_WATCHDOG
-#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWE | SYPCR_SWRI | SYPCR_SWP)
-#else
-#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWRI | SYPCR_SWP)
-#endif
-
-/*-----------------------------------------------------------------------
- * SIUMCR - SIU Module Configuration 11-6
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SYS_SIUMCR (SIUMCR_DLK | SIUMCR_DPC | SIUMCR_MPRE | SIUMCR_MLRC01 | SIUMCR_GB5E)
-
-/*-----------------------------------------------------------------------
- * TBSCR - Time Base Status and Control 11-26
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SYS_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF)
-
-/*-----------------------------------------------------------------------
- * RTCSC - Real-Time Clock Status and Control Register 11-27
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SYS_RTCSC (RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE)
-
-/*-----------------------------------------------------------------------
- * PISCR - Periodic Interrupt Status and Control 11-31
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SYS_PISCR (PISCR_PS | PISCR_PITF)
-
-/*-----------------------------------------------------------------------
- * PLPRCR - PLL, Low-Power, and Reset Control Register 15-30
- *-----------------------------------------------------------------------
- */
-
-/* MF (Multiplication Factor of SPLL) */
-/* Sets the QS823 to specified clock from 32KHz clock at EXTAL. */
-#define vPLPRCR_MF ((CONFIG_CLOCK_MULT+1) << 20)
-#define CONFIG_SYS_PLPRCR (vPLPRCR_MF | PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST | PLPRCR_LOLRE)
-
-/*-----------------------------------------------------------------------
- * SCCR - System Clock and reset Control Register 15-27
- *-----------------------------------------------------------------------
- */
-#if defined(CONFIG_CLOCK_16MHZ) || defined(CONFIG_CLOCK_33MHZ) || defined(CONFIG_CLOCK_50MHZ)
-#define CONFIG_SYS_SCCR (SCCR_TBS | SCCR_EBDF00 | SCCR_DFBRG00)
-#define CONFIG_SYS_BRGCLK_PRESCALE 1
-#endif
-
-#if defined(CONFIG_CLOCK_66MHZ)
-#define CONFIG_SYS_SCCR (SCCR_TBS | SCCR_EBDF00 | SCCR_DFBRG01)
-#define CONFIG_SYS_BRGCLK_PRESCALE 4
-#endif
-
-#if defined(CONFIG_CLOCK_80MHZ)
-#define CONFIG_SYS_SCCR (SCCR_TBS | SCCR_EBDF01 | SCCR_DFBRG01)
-#define CONFIG_SYS_BRGCLK_PRESCALE 4
-#endif
-
-#define SCCR_MASK CONFIG_SYS_SCCR
-
-/*-----------------------------------------------------------------------
- * Debug Enable Register
- * 0x73E67C0F - All interrupts handled by BDM
- * 0x00824001 - Only interrupts needed by MWDebug.exe handled by BDM
- *-----------------------------------------------------------------------
-#define CONFIG_SYS_DER 0x73E67C0F
-#define CONFIG_SYS_DER 0x0082400F
-
- #-------------------------------------------------------------------------
- # Program the Debug Enable Register (DER). This register provides the user
- # with the reason for entering into the debug mode. We want all conditions
- # to end up as an exception. We don't want to enter into debug mode for
- # any condition. See the back of of the Development Support section of the
- # MPC860 User Manual for a description of this register.
- #-------------------------------------------------------------------------
-*/
-#define CONFIG_SYS_DER 0
-
-/*-----------------------------------------------------------------------
- * Memory Controller Initialization Constants
- *-----------------------------------------------------------------------
- */
-
-/*
- * BR0 and OR0 (AMD dual FLASH devices)
- * Base address = 0xFFF0_0000 - 0xFFF7_FFFF (After relocation)
- */
-#define CONFIG_SYS_PRELIM_OR_AM
-#define CONFIG_SYS_OR_TIMING_FLASH
-
-/*
- *-----------------------------------------------------------------------
- * Base Register 0 (BR0): Bank 0 is assigned to the 8Mbyte (2M X 32)
- * flash that resides on the QS823.
- *-----------------------------------------------------------------------
- */
-
-/* BA (Base Address) = 0xFF80+0b for a total of 17 bits. 17 bit base addr */
-/* represents a minumum 32K block size. */
-#define vBR0_BA ((0xFF80 << 16) + (0 << 15))
-#define CONFIG_SYS_BR0_PRELIM (vBR0_BA | BR_V)
-
-/* AM (Address Mask) = 0xFF80+0b = We've masked the upper 9 bits */
-/* which defines a 8 Mbyte memory block. */
-#define vOR0_AM ((0xFF80 << 16) + (0 << 15))
-
-#if defined(CONFIG_CLOCK_50MHZ) || defined(CONFIG_CLOCK_80MHZ)
-/* 0101 = Add a 5 clock cycle wait state */
-#define CONFIG_SYS_OR0_PRELIM (vOR0_AM | OR_CSNT_SAM | 0R_ACS_DIV4 | OR_BI | OR_SCY_5_CLK)
-#endif
-
-#if defined(CONFIG_CLOCK_33MHZ) || defined(CONFIG_CLOCK_66MHZ)
-/* 0011 = Add a 3 clock cycle wait state */
-/* 29.8ns clock * (3 + 2) = 149ns cycle time */
-#define CONFIG_SYS_OR0_PRELIM (vOR0_AM | OR_CSNT_SAM | OR_ACS_DIV4 | OR_BI | OR_SCY_3_CLK)
-#endif
-
-#if defined(CONFIG_CLOCK_16MHZ)
-/* 0010 = Add a 2 clock cycle wait state */
-#define CONFIG_SYS_OR0_PRELIM (vOR0_AM | OR_CSNT_SAM | OR_ACS_DIV4 | OR_BI | OR_SCY_2_CLK)
-#endif
-
-/*
- * BR1 and OR1 (SDRAM)
- * Base Address = 0x00000000 - 0x00FF_FFFF (16M After relocation)
- * Base Address = 0x00000000 - 0x01FF_FFFF (32M After relocation)
- * Base Address = 0x00000000 - 0x03FF_FFFF (64M After relocation)
- * Base Address = 0x00000000 - 0x07FF_FFFF (128M After relocation)
- */
-
-#define SDRAM_BASE 0x00000000 /* SDRAM bank */
-#define SDRAM_PRELIM_OR_AM 0xF8000000 /* map max. 128 MB */
-
-/* AM (Address Mask) = 0xF800+0b = We've masked the upper 5 bits which
- * represents a 128 Mbyte block the DRAM in
- * this address base.
- */
-#define vOR1_AM ((0xF800 << 16) + (0 << 15))
-#define vBR1_BA ((0x0000 << 16) + (0 << 15))
-#define CONFIG_SYS_OR1 (vOR1_AM | OR_CSNT_SAM | OR_BI)
-#define CONFIG_SYS_BR1 (vBR1_BA | BR_MS_UPMA | BR_V)
-
-/* Machine A Mode Register */
-
-/* PTA Periodic Timer A */
-
-#if defined(CONFIG_CLOCK_80MHZ)
-#define vMAMR_PTA (19 << 24)
-#endif
-
-#if defined(CONFIG_CLOCK_66MHZ)
-#define vMAMR_PTA (16 << 24)
-#endif
-
-#if defined(CONFIG_CLOCK_50MHZ)
-#define vMAMR_PTA (195 << 24)
-#endif
-
-#if defined(CONFIG_CLOCK_33MHZ)
-#define vMAMR_PTA (131 << 24)
-#endif
-
-#if defined(CONFIG_CLOCK_16MHZ)
-#define vMAMR_PTA (65 << 24)
-#endif
-
-/* For boards with 16M of SDRAM */
-#define SDRAM_16M_MAX_SIZE 0x01000000 /* max 16MB SDRAM */
-#define CONFIG_SYS_16M_MAMR (vMAMR_PTA | MAMR_AMA_TYPE_0 | MAMR_DSA_2_CYCL | MAMR_G0CLA_A11 |\
-MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X)
-
-/* For boards with 32M of SDRAM */
-#define SDRAM_32M_MAX_SIZE 0x02000000 /* max 32MB SDRAM */
-#define CONFIG_SYS_32M_MAMR (vMAMR_PTA | MAMR_AMA_TYPE_1 | MAMR_DSA_2_CYCL | MAMR_G0CLA_A10 |\
-MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X)
-
-
-/* Memory Periodic Timer Prescaler Register */
-
-#if defined(CONFIG_CLOCK_66MHZ) || defined(CONFIG_CLOCK_80MHZ)
-/* Divide by 32 */
-#define CONFIG_SYS_MPTPR 0x02
-#endif
-
-#if defined(CONFIG_CLOCK_16MHZ) || defined(CONFIG_CLOCK_33MHZ) || defined(CONFIG_CLOCK_50MHZ)
-/* Divide by 16 */
-#define CONFIG_SYS_MPTPR 0x04
-#endif
-
-/*
- * BR2 and OR2 (Unused)
- * Base address = 0xF020_0000 - 0xF020_0FFF
- *
- */
-#define CONFIG_SYS_OR2_PRELIM 0xFFF00000
-#define CONFIG_SYS_BR2_PRELIM 0xF0200000
-
-/*
- * BR3 and OR3 (External Bus CS3)
- * Base address = 0xF030_0000 - 0xF030_0FFF
- *
- */
-#define CONFIG_SYS_OR3_PRELIM 0xFFF00000
-#define CONFIG_SYS_BR3_PRELIM 0xF0300000
-
-/*
- * BR4 and OR4 (External Bus CS3)
- * Base address = 0xF040_0000 - 0xF040_0FFF
- *
- */
-#define CONFIG_SYS_OR4_PRELIM 0xFFF00000
-#define CONFIG_SYS_BR4_PRELIM 0xF0400000
-
-
-/*
- * BR4 and OR4 (External Bus CS3)
- * Base address = 0xF050_0000 - 0xF050_0FFF
- *
- */
-#define CONFIG_SYS_OR5_PRELIM 0xFFF00000
-#define CONFIG_SYS_BR5_PRELIM 0xF0500000
-
-/*
- * BR6 and OR6 (Unused)
- * Base address = 0xF060_0000 - 0xF060_0FFF
- *
- */
-#define CONFIG_SYS_OR6_PRELIM 0xFFF00000
-#define CONFIG_SYS_BR6_PRELIM 0xF0600000
-
-/*
- * BR7 and OR7 (Unused)
- * Base address = 0xF070_0000 - 0xF070_0FFF
- *
- */
-#define CONFIG_SYS_OR7_PRELIM 0xFFF00000
-#define CONFIG_SYS_BR7_PRELIM 0xF0700000
-
-/*
- * Sanity checks
- */
-#if defined(CONFIG_SCC1_ENET) && defined(CONFIG_FEC_ENET)
-#error Both CONFIG_SCC1_ENET and CONFIG_FEC_ENET configured
-#endif
-
-#endif /* __CONFIG_H */
diff --git a/include/configs/QS850.h b/include/configs/QS850.h
deleted file mode 100644
index f114213..0000000
--- a/include/configs/QS850.h
+++ /dev/null
@@ -1,551 +0,0 @@
-/*
- * (C) Copyright 2003
- * MuLogic B.V.
- *
- * (C) Copyright 2002
- * Simple Network Magic Corporation
- *
- * (C) Copyright 2000
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-/*
- * board/config.h - configuration options, board specific
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/* various debug settings */
-#undef CONFIG_SYS_DEVICE_NULLDEV /* null device */
-#undef CONFIG_SILENT_CONSOLE /* silent console */
-#undef CONFIG_SYS_CONSOLE_INFO_QUIET /* silent console ? */
-#undef DEBUG_FLASH /* debug flash code */
-#undef FLASH_DEBUG /* debug fash code */
-#undef DEBUG_ENV /* debug environment code */
-
-#define CONFIG_SYS_DIRECT_FLASH_TFTP 1 /* allow direct tftp to flash */
-#define CONFIG_ENV_OVERWRITE 1 /* allow overwrite MAC address */
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-#define CONFIG_MPC850 1 /* This is a MPC850 CPU */
-#define CONFIG_QS850 1 /* ...on a QS850 module */
-#define CONFIG_SCC2_ENET 1 /* SCC2 10BaseT ethernet */
-
-#define CONFIG_SYS_TEXT_BASE 0xFFF00000
-
-/* Select the target clock speed */
-#undef CONFIG_CLOCK_16MHZ /* cpu=16,777,216 Hz, mem=16Mhz */
-#undef CONFIG_CLOCK_33MHZ /* cpu=33,554,432 Hz, mem=33Mhz */
-#undef CONFIG_CLOCK_50MHZ /* cpu=49,971,200 Hz, mem=33Mhz */
-#define CONFIG_CLOCK_66MHZ 1 /* cpu=67,108,864 Hz, mem=66Mhz */
-#undef CONFIG_CLOCK_80MHZ /* cpu=79,986,688 Hz, mem=33Mhz */
-
-#ifdef CONFIG_CLOCK_16MHZ
-#define CONFIG_CLOCK_MULT 512
-#endif
-
-#ifdef CONFIG_CLOCK_33MHZ
-#define CONFIG_CLOCK_MULT 1024
-#endif
-
-#ifdef CONFIG_CLOCK_50MHZ
-#define CONFIG_CLOCK_MULT 1525
-#endif
-
-#ifdef CONFIG_CLOCK_66MHZ
-#define CONFIG_CLOCK_MULT 2048
-#endif
-
-#ifdef CONFIG_CLOCK_80MHZ
-#define CONFIG_CLOCK_MULT 2441
-#endif
-
-/* choose flash size, 4Mb or 8Mb */
-#define CONFIG_FLASH_4MB 1 /* board has 4Mb flash */
-#undef CONFIG_FLASH_8MB /* board has 8Mb flash */
-
-#define CONFIG_CLOCK_BASE 32768 /* Base clock input freq */
-
-#define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */
-#undef CONFIG_8xx_CONS_SMC2
-#undef CONFIG_8xx_CONS_NONE
-
-#define CONFIG_BAUDRATE 38400 /* console baudrate = 38.4kbps */
-
-#undef CONFIG_CLOCKS_IN_MHZ /* clocks passsed to Linux in MHz */
-
-/* Define default IP addresses */
-#define CONFIG_IPADDR 192.168.1.99 /* own ip address */
-#define CONFIG_SERVERIP 192.168.1.19 /* used for tftp (not nfs?) */
-
-/* message to say directly after booting */
-#define CONFIG_PREBOOT "echo '';" \
- "echo 'type:';" \
- "echo 'run boot_nfs to boot to NFS';" \
- "echo 'run boot_flash to boot to flash';" \
- "echo '';" \
- "echo 'run flash_rootfs to install a new rootfs';" \
- "echo 'run flash_env to clear the env sector';" \
- "echo 'run flash_rw to clear the rw fs';" \
- "echo 'run flash_uboot to install a new u-boot';" \
- "echo 'run flash_kernel to install a new kernel';"
-
-/* wait 5 seconds before executing CONFIG_BOOTCOMMAND */
-#define CONFIG_BOOTDELAY 5
-#define CONFIG_BOOTCOMMAND "run boot_nfs"
-
-#undef CONFIG_BOOTARGS /* made by set_nfs of set_flash */
-
-/* Our flash filesystem looks like this
- *
- * 4Mb board:
- * ffc0 0000 - ffeb ffff root filesystem (jffs2) (~3Mb)
- * ffec 0000 - ffed ffff read-write filesystem (ext2)
- * ffee 0000 - ffef ffff environment
- * fff0 0000 - fff1 ffff u-boot
- * fff2 0000 - ffff ffff linux kernel
- *
- * 8Mb board:
- * ff80 0000 - ffeb ffff root filesystem (jffs2) (~7Mb)
- * ffec 0000 - ffed ffff read-write filesystem (ext2)
- * ffee 0000 - ffef ffff environment
- * fff0 0000 - fff1 ffff u-boot
- * fff2 0000 - ffff ffff linux kernel
- *
- */
-
-/* environment for 4Mb board */
-#ifdef CONFIG_FLASH_4MB
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "serial#=QS850\0" \
- "hostname=qs850\0" \
- "netdev=eth0\0" \
- "ethaddr=00:01:02:B4:36:56\0" \
- "rootpath=/exports/rootfs\0" \
- "mtdparts=mtdparts=phys:2816k(root),128k(rw),128k(env),128k(u-boot),-(kernel)\0" \
- /* fill in variables */ \
- "set_ip=setenv ip ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off\0" \
- "set_nfs=setenv bootargs root=/dev/nfs rw nfsroot=$serverip:$rootpath $ip init=/sbin/init $mtdparts\0" \
- "set_flash=setenv bootargs root=/dev/mtdblock1 ro $ip init=/sbin/init $mtdparts\0" \
- /* commands */ \
- "boot_nfs=run set_ip; run set_nfs; tftp 0x400000 /tftpboot/vmlinux.UBoot; bootm 0x400000\0" \
- "boot_flash=run set_ip; run set_flash; bootm fff20000\0" \
- /* reinstall flash parts */ \
- "flash_rootfs=protect off ffc00000 ffebffff; era ffc00000 ffebffff; tftp ffc00000 /tftpboot/rootfs.jffs2\0" \
- "flash_rw=protect off ffec0000 ffedffff; era ffec0000 ffedffff\0" \
- "flash_env=protect off ffee0000 ffefffff; era ffee0000 ffefffff\0" \
- "flash_uboot=protect off fff00000 fff1ffff; era fff00000 fff1ffff; tftp fff00000 /tftpboot/u-boot.4mb.bin\0" \
- "flash_kernel=protect off fff20000 ffffffff; era fff20000 ffffffff; tftp fff20000 /tftpboot/vmlinux.UBoot\0"
-#endif /* CONFIG_FLASH_4MB */
-
-/* environment for 8Mb board */
-#ifdef CONFIG_FLASH_8MB
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "serial#=QS850\0" \
- "hostname=qs850\0" \
- "netdev=eth0\0" \
- "ethaddr=00:01:02:B4:36:56\0" \
- "rootpath=/exports/rootfs\0" \
- "mtdparts=mtdparts=phys:6912k(root),128k(rw),128k(env),128k(u-boot),-(kernel)\0" \
- /* fill in variables */ \
- "set_ip=setenv ip ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off\0" \
- "set_nfs=setenv bootargs root=/dev/nfs rw nfsroot=$serverip:$rootpath $ip init=/sbin/init $mtdparts\0" \
- "set_flash=setenv bootargs root=/dev/mtdblock1 ro $ip init=/sbin/init $mtdparts\0" \
- /* commands */ \
- "boot_nfs=run set_ip; run set_nfs; tftp 0x400000 /tftpboot/vmlinux.UBoot; bootm 0x400000\0" \
- "boot_flash=run set_ip; run set_flash; bootm fff20000\0" \
- /* reinstall flash parts */ \
- "flash_rootfs=protect off ff800000 ffebffff; era ff800000 ffebffff; tftp ff800000 /tftpboot/rootfs.jffs2\0" \
- "flash_rw=protect off ffec0000 ffedffff; era ffec0000 ffedffff\0" \
- "flash_env=protect off ffee0000 ffefffff; era ffee0000 ffefffff\0" \
- "flash_uboot=protect off fff00000 fff1ffff; era fff00000 fff1ffff; tftp fff00000 /tftpboot/u-boot.8mb.bin\0" \
- "flash_kernel=protect off fff20000 ffffffff; era fff20000 ffffffff; tftp fff20000 /tftpboot/vmlinux.UBoot\0"
-#endif /* CONFIG_FLASH_8MB */
-
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#undef CONFIG_SYS_LOADS_BAUD_CHANGE /* don't allow baudrate change */
-#undef CONFIG_WATCHDOG /* watchdog disabled */
-#undef CONFIG_STATUS_LED /* Status LED disabled */
-#undef CONFIG_CAN_DRIVER /* CAN Driver support disabled */
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_SUBNETMASK
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_BOOTFILESIZE
-
-#undef CONFIG_MAC_PARTITION
-#undef CONFIG_DOS_PARTITION
-
-#define CONFIG_RTC_MPC8xx /* use internal RTC of MPC8xx */
-
-
-/*
- * Command line configuration.
- */
-
-#define CONFIG_CMD_BDI
-#define CONFIG_CMD_BOOTD
-#define CONFIG_CMD_CONSOLE
-#define CONFIG_CMD_DATE
-#define CONFIG_CMD_SAVEENV
-#define CONFIG_CMD_FLASH
-#define CONFIG_CMD_IMI
-#define CONFIG_CMD_IMMAP
-#define CONFIG_CMD_MEMORY
-#define CONFIG_CMD_NET
-#define CONFIG_CMD_RUN
-
-
-/*-----------------------------------------------------------------------
- * Environment variable storage is in FLASH, one sector before U-boot
- */
-#define CONFIG_ENV_IS_IN_FLASH 1
-#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128Kb, one whole sector */
-#define CONFIG_ENV_SIZE 0x2000 /* 8kb */
-#define CONFIG_ENV_ADDR 0xffee0000 /* address of env sector */
-
-/*-----------------------------------------------------------------------
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-
-#define CONFIG_SYS_HUSH_PARSER 1 /* use "hush" command parser */
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-
-#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works */
-#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
-
-#define CONFIG_SYS_LOAD_ADDR 0x400000 /* default load address */
-
-/*-----------------------------------------------------------------------
- * Low Level Configuration Settings
- * (address mappings, register initial values, etc.)
- * You should know what you are doing if you make changes here.
- */
-
-/*-----------------------------------------------------------------------
- * Internal Memory Mapped Register
- */
-#define CONFIG_SYS_IMMR 0xFF000000
-
-/*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area (in DPRAM)
- */
-#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR
-#define CONFIG_SYS_INIT_RAM_SIZE 0x2F00 /* Size of used area in DPRAM */
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- */
-#define CONFIG_SYS_SDRAM_BASE 0x00000000
-#define CONFIG_SYS_FLASH_BASE 0xFF800000 /* Allow an 8Mbyte window */
-
-#define FLASH_BASE0_4M_PRELIM 0xFFC00000 /* Base for 4M Flash */
-#define FLASH_BASE0_8M_PRELIM 0xFF800000 /* Base for 8M Flash */
-
-#define CONFIG_SYS_MONITOR_LEN (192 << 10) /* Reserve 192 kB for Monitor */
-#define CONFIG_SYS_MONITOR_BASE 0xFFF00000 /* U-boot location */
-#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-
-/*-----------------------------------------------------------------------
- * TODO flash parameters
- * FLASH organization for Intel Strataflash
- */
-#undef CONFIG_SYS_FLASH_16BIT /* 32-bit wide flash memory */
-#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 71 /* max number of sectors on one chip */
-
-#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
-
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CONFIG_SYS_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CACHELINE_SHIFT 4 /* log base 2 of the above value */
-#endif
-
-/*-----------------------------------------------------------------------
- * SYPCR - System Protection Control 11-9
- * SYPCR can only be written once after reset!
- *-----------------------------------------------------------------------
- * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
- */
-
-#ifdef CONFIG_WATCHDOG
-#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWE | SYPCR_SWRI | SYPCR_SWP)
-#else
-#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWRI | SYPCR_SWP)
-#endif
-
-/*-----------------------------------------------------------------------
- * SIUMCR - SIU Module Configuration 11-6
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SYS_SIUMCR (SIUMCR_DLK | SIUMCR_DPC | SIUMCR_MPRE | SIUMCR_MLRC01 | SIUMCR_GB5E)
-
-/*-----------------------------------------------------------------------
- * TBSCR - Time Base Status and Control 11-26
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SYS_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF)
-
-/*-----------------------------------------------------------------------
- * RTCSC - Real-Time Clock Status and Control Register 11-27
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SYS_RTCSC (RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE)
-
-/*-----------------------------------------------------------------------
- * PISCR - Periodic Interrupt Status and Control 11-31
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SYS_PISCR (PISCR_PS | PISCR_PITF)
-
-/*-----------------------------------------------------------------------
- * PLPRCR - PLL, Low-Power, and Reset Control Register 15-30
- *-----------------------------------------------------------------------
- */
-
-/* MF (Multiplication Factor of SPLL) */
-/* Sets the QS850 to specified clock from 32KHz clock at EXTAL. */
-#define vPLPRCR_MF ((CONFIG_CLOCK_MULT+1) << 20)
-#define CONFIG_SYS_PLPRCR (vPLPRCR_MF | PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST | PLPRCR_LOLRE)
-
-/*-----------------------------------------------------------------------
- * SCCR - System Clock and reset Control Register 15-27
- *-----------------------------------------------------------------------
- */
-#if defined(CONFIG_CLOCK_16MHZ) || defined(CONFIG_CLOCK_33MHZ) || defined(CONFIG_CLOCK_50MHZ)
-#define CONFIG_SYS_SCCR (SCCR_TBS | SCCR_EBDF00 | SCCR_DFBRG00)
-#define CONFIG_SYS_BRGCLK_PRESCALE 1
-#endif
-
-#if defined(CONFIG_CLOCK_66MHZ)
-#define CONFIG_SYS_SCCR (SCCR_TBS | SCCR_EBDF00 | SCCR_DFBRG01)
-#define CONFIG_SYS_BRGCLK_PRESCALE 4
-#endif
-
-#if defined(CONFIG_CLOCK_80MHZ)
-#define CONFIG_SYS_SCCR (SCCR_TBS | SCCR_EBDF01 | SCCR_DFBRG01)
-#define CONFIG_SYS_BRGCLK_PRESCALE 4
-#endif
-
-#define SCCR_MASK CONFIG_SYS_SCCR
-
-/*-----------------------------------------------------------------------
- * Debug Enable Register
- * 0x73E67C0F - All interrupts handled by BDM
- * 0x00824001 - Only interrupts needed by MWDebug.exe handled by BDM
- *-----------------------------------------------------------------------
-#define CONFIG_SYS_DER 0x73E67C0F
-#define CONFIG_SYS_DER 0x0082400F
-
- #-------------------------------------------------------------------------
- # Program the Debug Enable Register (DER). This register provides the user
- # with the reason for entering into the debug mode. We want all conditions
- # to end up as an exception. We don't want to enter into debug mode for
- # any condition. See the back of of the Development Support section of the
- # MPC860 User Manual for a description of this register.
- #-------------------------------------------------------------------------
-*/
-#define CONFIG_SYS_DER 0
-
-/*-----------------------------------------------------------------------
- * Memory Controller Initialization Constants
- *-----------------------------------------------------------------------
- */
-
-/*
- * BR0 and OR0 (AMD dual FLASH devices)
- * Base address = 0xFFF0_0000 - 0xFFF7_FFFF (After relocation)
- */
-#define CONFIG_SYS_PRELIM_OR_AM
-#define CONFIG_SYS_OR_TIMING_FLASH
-
-/*
- *-----------------------------------------------------------------------
- * Base Register 0 (BR0): Bank 0 is assigned to the 8Mbyte (2M X 32)
- * flash that resides on the QS850.
- *-----------------------------------------------------------------------
- */
-
-/* BA (Base Address) = 0xFF80+0b for a total of 17 bits. 17 bit base addr */
-/* represents a minumum 32K block size. */
-#define vBR0_BA ((0xFF80 << 16) + (0 << 15))
-#define CONFIG_SYS_BR0_PRELIM (vBR0_BA | BR_V)
-
-/* AM (Address Mask) = 0xFF80+0b = We've masked the upper 9 bits */
-/* which defines a 8 Mbyte memory block. */
-#define vOR0_AM ((0xFF80 << 16) + (0 << 15))
-
-#if defined(CONFIG_CLOCK_50MHZ) || defined(CONFIG_CLOCK_80MHZ)
-/* 0101 = Add a 5 clock cycle wait state */
-#define CONFIG_SYS_OR0_PRELIM (vOR0_AM | OR_CSNT_SAM | 0R_ACS_DIV4 | OR_BI | OR_SCY_5_CLK)
-#endif
-
-#if defined(CONFIG_CLOCK_33MHZ) || defined(CONFIG_CLOCK_66MHZ)
-/* 0011 = Add a 3 clock cycle wait state */
-/* 29.8ns clock * (3 + 2) = 149ns cycle time */
-#define CONFIG_SYS_OR0_PRELIM (vOR0_AM | OR_CSNT_SAM | OR_ACS_DIV4 | OR_BI | OR_SCY_3_CLK)
-#endif
-
-#if defined(CONFIG_CLOCK_16MHZ)
-/* 0010 = Add a 2 clock cycle wait state */
-#define CONFIG_SYS_OR0_PRELIM (vOR0_AM | OR_CSNT_SAM | OR_ACS_DIV4 | OR_BI | OR_SCY_2_CLK)
-#endif
-
-/*
- * BR1 and OR1 (SDRAM)
- * Base Address = 0x00000000 - 0x00FF_FFFF (16M After relocation)
- * Base Address = 0x00000000 - 0x01FF_FFFF (32M After relocation)
- * Base Address = 0x00000000 - 0x03FF_FFFF (64M After relocation)
- * Base Address = 0x00000000 - 0x07FF_FFFF (128M After relocation)
- */
-
-#define SDRAM_BASE 0x00000000 /* SDRAM bank */
-#define SDRAM_PRELIM_OR_AM 0xF8000000 /* map max. 128 MB */
-
-/* AM (Address Mask) = 0xF800+0b = We've masked the upper 5 bits which
- * represents a 128 Mbyte block the DRAM in
- * this address base.
- */
-#define vOR1_AM ((0xF800 << 16) + (0 << 15))
-#define vBR1_BA ((0x0000 << 16) + (0 << 15))
-#define CONFIG_SYS_OR1 (vOR1_AM | OR_CSNT_SAM | OR_BI)
-#define CONFIG_SYS_BR1 (vBR1_BA | BR_MS_UPMA | BR_V)
-
-/* Machine A Mode Register */
-
-/* PTA Periodic Timer A */
-
-#if defined(CONFIG_CLOCK_80MHZ)
-#define vMAMR_PTA (19 << 24)
-#endif
-
-#if defined(CONFIG_CLOCK_66MHZ)
-#define vMAMR_PTA (16 << 24)
-#endif
-
-#if defined(CONFIG_CLOCK_50MHZ)
-#define vMAMR_PTA (195 << 24)
-#endif
-
-#if defined(CONFIG_CLOCK_33MHZ)
-#define vMAMR_PTA (131 << 24)
-#endif
-
-#if defined(CONFIG_CLOCK_16MHZ)
-#define vMAMR_PTA (65 << 24)
-#endif
-
-/* For boards with 16M of SDRAM */
-#define SDRAM_16M_MAX_SIZE 0x01000000 /* max 16MB SDRAM */
-#define CONFIG_SYS_16M_MAMR (vMAMR_PTA | MAMR_AMA_TYPE_0 | MAMR_DSA_2_CYCL | MAMR_G0CLA_A11 |\
-MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X)
-
-/* For boards with 32M of SDRAM */
-#define SDRAM_32M_MAX_SIZE 0x02000000 /* max 32MB SDRAM */
-#define CONFIG_SYS_32M_MAMR (vMAMR_PTA | MAMR_AMA_TYPE_1 | MAMR_DSA_2_CYCL | MAMR_G0CLA_A10 |\
-MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X)
-
-
-/* Memory Periodic Timer Prescaler Register */
-
-#if defined(CONFIG_CLOCK_66MHZ) || defined(CONFIG_CLOCK_80MHZ)
-/* Divide by 32 */
-#define CONFIG_SYS_MPTPR 0x02
-#endif
-
-#if defined(CONFIG_CLOCK_16MHZ) || defined(CONFIG_CLOCK_33MHZ) || defined(CONFIG_CLOCK_50MHZ)
-/* Divide by 16 */
-#define CONFIG_SYS_MPTPR 0x04
-#endif
-
-/*
- * BR2 and OR2 (Unused)
- * Base address = 0xF020_0000 - 0xF020_0FFF
- *
- */
-#define CONFIG_SYS_OR2_PRELIM 0xFFF00000
-#define CONFIG_SYS_BR2_PRELIM 0xF0200000
-
-/*
- * BR3 and OR3 (External Bus CS3)
- * Base address = 0xF030_0000 - 0xF030_0FFF
- *
- */
-#define CONFIG_SYS_OR3_PRELIM 0xFFF00000
-#define CONFIG_SYS_BR3_PRELIM 0xF0300000
-
-/*
- * BR4 and OR4 (External Bus CS3)
- * Base address = 0xF040_0000 - 0xF040_0FFF
- *
- */
-#define CONFIG_SYS_OR4_PRELIM 0xFFF00000
-#define CONFIG_SYS_BR4_PRELIM 0xF0400000
-
-
-/*
- * BR4 and OR4 (External Bus CS3)
- * Base address = 0xF050_0000 - 0xF050_0FFF
- *
- */
-#define CONFIG_SYS_OR5_PRELIM 0xFFF00000
-#define CONFIG_SYS_BR5_PRELIM 0xF0500000
-
-/*
- * BR6 and OR6 (Unused)
- * Base address = 0xF060_0000 - 0xF060_0FFF
- *
- */
-#define CONFIG_SYS_OR6_PRELIM 0xFFF00000
-#define CONFIG_SYS_BR6_PRELIM 0xF0600000
-
-/*
- * BR7 and OR7 (Unused)
- * Base address = 0xF070_0000 - 0xF070_0FFF
- *
- */
-#define CONFIG_SYS_OR7_PRELIM 0xFFF00000
-#define CONFIG_SYS_BR7_PRELIM 0xF0700000
-
-/*
- * Sanity checks
- */
-#if defined(CONFIG_SCC1_ENET) && defined(CONFIG_FEC_ENET)
-#error Both CONFIG_SCC1_ENET and CONFIG_FEC_ENET configured
-#endif
-
-#endif /* __CONFIG_H */
diff --git a/include/configs/QS860T.h b/include/configs/QS860T.h
deleted file mode 100644
index 9958c09..0000000
--- a/include/configs/QS860T.h
+++ /dev/null
@@ -1,390 +0,0 @@
-/*
- * (C) Copyright 2003
- * MuLogic B.V.
- *
- * (C) Copyright 2002
- * Simple Network Magic Corporation
- *
- * (C) Copyright 2000
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-/*
- * board/config.h - configuration options, board specific
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/* various debug settings */
-#undef CONFIG_SYS_DEVICE_NULLDEV /* null device */
-#undef CONFIG_SILENT_CONSOLE /* silent console */
-#undef CONFIG_SYS_CONSOLE_INFO_QUIET /* silent console ? */
-#undef DEBUG_FLASH /* debug flash code */
-#undef FLASH_DEBUG /* debug fash code */
-#undef DEBUG_ENV /* debug environment code */
-
-#define CONFIG_SYS_DIRECT_FLASH_TFTP 1 /* allow direct tftp to flash */
-#define CONFIG_ENV_OVERWRITE 1 /* allow overwrite MAC address */
-
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-
-#define CONFIG_MPC860 1 /* This is a MPC860 CPU */
-#define CONFIG_QS860T 1 /* ...on a QS860T module */
-
-/* Start address of 512K Socketed Flash */
-#define CONFIG_SYS_TEXT_BASE 0xFFF00000
-
-#define CONFIG_FEC_ENET 1 /* FEC 10/100BaseT ethernet */
-#define CONFIG_MII
-#define FEC_INTERRUPT SIU_LEVEL1
-#undef CONFIG_SCC1_ENET /* SCC1 10BaseT ethernet */
-#define CONFIG_SYS_DISCOVER_PHY
-
-#undef CONFIG_8xx_CONS_SMC1
-#define CONFIG_8xx_CONS_SMC2 1 /* Console is on SMC */
-#undef CONFIG_8xx_CONS_NONE
-
-#define CONFIG_BAUDRATE 38400 /* console baudrate = 38.4kbps */
-
-#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
-
-/* Pass clocks to Linux 2.4.18 in Hz */
-#undef CONFIG_CLOCKS_IN_MHZ /* clocks passsed to Linux in MHz */
-
-#define CONFIG_PREBOOT "echo;" \
- "echo 'Type \\\"run flash_nfs\\\" to mount root filesystem over NFS';" \
- "echo"
-
-#undef CONFIG_BOOTARGS
-/* TODO compare against CADM860 */
-#define CONFIG_BOOTCOMMAND "bootp; " \
- "setenv bootargs root=/dev/nfs rw nfsroot=${serverip}:${rootpath} " \
- "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off; " \
- "bootm"
-
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#undef CONFIG_SYS_LOADS_BAUD_CHANGE /* don't allow baudrate change */
-
-#undef CONFIG_WATCHDOG /* watchdog disabled */
-
-#undef CONFIG_STATUS_LED /* Status LED disabled */
-
-#undef CONFIG_CAN_DRIVER /* CAN Driver support disabled */
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_SUBNETMASK
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_BOOTFILESIZE
-
-
-#define CONFIG_MAC_PARTITION
-#define CONFIG_DOS_PARTITION
-
-#define CONFIG_RTC_MPC8xx /* use internal RTC of MPC8xx */
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_REGINFO
-#define CONFIG_CMD_IMMAP
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_NET
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_DATE
-
-
-/* TODO */
-#if 0
-/* Look at these */
-CONFIG_IPADDR
-CONFIG_SERVERIP
-CONFIG_I2C
-CONFIG_SPI
-#endif
-
-/*
- * Environment variable storage is in NVRAM
- */
-#define CONFIG_ENV_IS_IN_NVRAM 1
-#define CONFIG_ENV_SIZE 0x00001000 /* We use only the last 4K for PPCBoot */
-#define CONFIG_ENV_ADDR 0xD100E000
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-
-#define CONFIG_SYS_HUSH_PARSER 1 /* use "hush" command parser */
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-
-/* TODO - size? */
-#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works */
-#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
-
-#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
-
-/*-----------------------------------------------------------------------
- * Low Level Configuration Settings
- * (address mappings, register initial values, etc.)
- * You should know what you are doing if you make changes here.
- */
-/*-----------------------------------------------------------------------
- * Internal Memory Mapped Register
- */
-#define CONFIG_SYS_IMMR 0xF0000000
-
-/*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area (in DPRAM)
- */
-#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR
-#define CONFIG_SYS_INIT_RAM_SIZE 0x2F00 /* Size of used area in DPRAM */
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- */
-#define CONFIG_SYS_SDRAM_BASE 0x00000000
-#define CONFIG_SYS_FLASH_BASE 0xFFF00000
-
-#define CONFIG_SYS_MONITOR_LEN (192 << 10) /* Reserve 192 kB for Monitor */
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-
-/* TODO flash parameters */
-/*-----------------------------------------------------------------------
- * FLASH organization for Intel Strataflash
- */
-#define CONFIG_SYS_FLASH_16BIT 1 /* 16-bit wide flash memory */
-#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 64 /* max number of sectors on one chip */
-
-#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
-
-#undef CONFIG_ENV_IS_IN_FLASH
-
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CONFIG_SYS_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CACHELINE_SHIFT 4 /* log base 2 of the above value */
-#endif
-
-/*-----------------------------------------------------------------------
- * SYPCR - System Protection Control 11-9
- * SYPCR can only be written once after reset!
- *-----------------------------------------------------------------------
- * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
- */
-#if defined(CONFIG_WATCHDOG)
-#define CONFIG_SYS_SYPCR (0xFFFFFF88 | SYPCR_SWE | SYPCR_SWRI)
-#else
-#define CONFIG_SYS_SYPCR 0xFFFFFF88
-#endif
-
-/*-----------------------------------------------------------------------
- * SIUMCR - SIU Module Configuration 11-6
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SYS_SIUMCR 0x00620000
-
-/*-----------------------------------------------------------------------
- * TBSCR - Time Base Status and Control 11-26
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SYS_TBSCR 0x00C3
-
-/*-----------------------------------------------------------------------
- * RTCSC - Real-Time Clock Status and Control Register 11-27
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SYS_RTCSC (RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE)
-
-/*-----------------------------------------------------------------------
- * PISCR - Periodic Interrupt Status and Control 11-31
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SYS_PISCR 0x0082
-
-/*-----------------------------------------------------------------------
- * PLPRCR - PLL, Low-Power, and Reset Control Register 15-30
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SYS_PLPRCR 0x0090D000
-
-/*-----------------------------------------------------------------------
- * SCCR - System Clock and reset Control Register 15-27
- *-----------------------------------------------------------------------
- */
-#define SCCR_MASK SCCR_EBDF11
-#define CONFIG_SYS_SCCR 0x02000000
-
-
-/*-----------------------------------------------------------------------
- * Debug Enable Register
- * 0x73E67C0F - All interrupts handled by BDM
- * 0x00824001 - Only interrupts needed by MWDebug.exe handled by BDM
- *-----------------------------------------------------------------------
-#define CONFIG_SYS_DER 0x73E67C0F
-*/
-#define CONFIG_SYS_DER 0x0082400F
-
-
-/*-----------------------------------------------------------------------
- * Memory Controller Initialization Constants
- *-----------------------------------------------------------------------
- */
-
-/*
- * BR0 and OR0 (AMD 512K Socketed FLASH)
- * Base address = 0xFFF0_0000 - 0xFFF7_FFFF (After relocation)
- */
-#define CONFIG_SYS_PRELIM_OR_AM
-#define CONFIG_SYS_OR_TIMING_FLASH
-
-#define FLASH_BASE0_PRELIM 0xFFF00001
-#define CONFIG_SYS_OR0_PRELIM 0xFFF80D42
-#define CONFIG_SYS_BR0_PRELIM 0xFFF00401
-
-
-/*
- * BR1 and OR1 (Intel 8M StrataFLASH)
- * Base address = 0xD000_0000 - 0xD07F_FFFF
- */
-
-#define FLASH_BASE1_PRELIM 0xD0000000
-#define CONFIG_SYS_OR1_PRELIM 0xFF800D42
-#define CONFIG_SYS_BR1_PRELIM 0xD0000801
-/* #define CONFIG_SYS_OR1 0xFF800D42 */
-/* #define CONFIG_SYS_BR1 0xD0000801 */
-
-
-/*
- * BR2 and OR2 (SDRAM)
- * Base Address = 0x00000000 - 0x00FF_FFFF (16M After relocation)
- * Base Address = 0x00000000 - 0x03FF_FFFF (64M After relocation)
- * Base Address = 0x00000000 - 0x07FF_FFFF (128M After relocation)
- *
- */
-#define SDRAM_BASE 0x00000000 /* SDRAM bank */
-#define SDRAM_PRELIM_OR_AM 0xF8000000 /* map max. 128 MB */
-
-/* SDRAM timing */
-#define SDRAM_TIMING 0x00000A00
-
-/* For boards with 16M of SDRAM */
-#define SDRAM_16M_MAX_SIZE 0x01000000 /* max 16MB SDRAM */
-#define CONFIG_SYS_16M_MBMR 0x18802114 /* Mem Periodic Timer Prescaler */
-
-/* For boards with 64M of SDRAM */
-#define SDRAM_64M_MAX_SIZE 0x04000000 /* max 64MB SDRAM */
-/* TODO - determine real value */
-#define CONFIG_SYS_64M_MBMR 0x18802114 /* Mem Period Timer Prescaler */
-
-#define CONFIG_SYS_OR2 (SDRAM_PRELIM_OR_AM | SDRAM_TIMING)
-#define CONFIG_SYS_BR2 (SDRAM_BASE | 0x000000C1)
-
-
-/*
- * BR3 and OR3 (NVRAM, Sipex, NAND Flash)
- * Base address = 0xD100_0000 - 0xD100_FFFF (64K NVRAM)
- * Base address = 0xD108_0000 - 0xD108_0000 (Sipex chip ctl register)
- * Base address = 0xD110_0000 - 0xD110_0000 (NAND ctl register)
- * Base address = 0xD138_0000 - 0xD138_0000 (LED ctl register)
- *
- */
-
-#define CONFIG_SYS_OR3_PRELIM 0xFFC00DF6
-#define CONFIG_SYS_BR3_PRELIM 0xD1000401
-/* #define CONFIG_SYS_OR3 0xFFC00DF6 */
-/* #define CONFIG_SYS_BR3 0xD1000401 */
-
-
-/*
- * BR4 and OR4 (Unused)
- * Base address = 0xE000_0000 - 0xE3FF_FFFF
- *
- */
-
-#define CONFIG_SYS_OR4_PRELIM 0xFF000000
-#define CONFIG_SYS_BR4_PRELIM 0xE0000000
-/* #define CONFIG_SYS_OR4 0xFF000000 */
-/* #define CONFIG_SYS_BR4 0xE0000000 */
-
-
-/*
- * BR5 and OR5 (Expansion bus)
- * Base address = 0xE400_0000 - 0xE7FF_FFFF
- *
- */
-
-#define CONFIG_SYS_OR5_PRELIM 0xFF000000
-#define CONFIG_SYS_BR5_PRELIM 0xE4000000
-/* #define CONFIG_SYS_OR5 0xFF000000 */
-/* #define CONFIG_SYS_BR5 0xE4000000 */
-
-
-/*
- * BR6 and OR6 (Expansion bus)
- * Base address = 0xE800_0000 - 0xEBFF_FFFF
- *
- */
-
-#define CONFIG_SYS_OR6_PRELIM 0xFF000000
-#define CONFIG_SYS_BR6_PRELIM 0xE8000000
-/* #define CONFIG_SYS_OR6 0xFF000000 */
-/* #define CONFIG_SYS_BR6 0xE8000000 */
-
-
-/*
- * BR7 and OR7 (Expansion bus)
- * Base address = 0xEC00_0000 - 0xEFFF_FFFF
- *
- */
-
-#define CONFIG_SYS_OR7_PRELIM 0xFF000000
-#define CONFIG_SYS_BR7_PRELIM 0xE8000000
-/* #define CONFIG_SYS_OR7 0xFF000000 */
-/* #define CONFIG_SYS_BR7 0xE8000000 */
-
-/*
- * Sanity checks
- */
-#if defined(CONFIG_SCC1_ENET) && defined(CONFIG_FEC_ENET)
-#error Both CONFIG_SCC1_ENET and CONFIG_FEC_ENET configured
-#endif
-
-#endif /* __CONFIG_H */
generated by cgit v1.1 at 2024-11-12 15:52:18 +0000