ppc: Remove MPC8349EMDS board and ARCH_MPC8349 support

This board has not been converted to CONFIG_DM by the deadline.
Remove it.

Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>

1 files changed, 0 insertions, 315 deletions

diff --git a/include/configs/MPC8349EMDS.h b/include/configs/MPC8349EMDS.h
deleted file mode 100644
index dd11e98..0000000
--- a/include/configs/MPC8349EMDS.h
+++ /dev/null
@@ -1,315 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * (C) Copyright 2006-2010
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- */
-
-/*
- * mpc8349emds board configuration file
- *
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- */
-#define CONFIG_E300		1	/* E300 Family */
-
-#undef CONFIG_SYS_DRAM_TEST		/* memory test, takes time */
-
-/*
- * DDR Setup
- */
-#define CONFIG_SPD_EEPROM		/* use SPD EEPROM for DDR setup*/
-
-/*
- * SYS_FSL_DDR2 is selected in Kconfig to use unified DDR driver
- * unselect it to use old spd_sdram.c
- */
-#define CONFIG_SYS_SPD_BUS_NUM	0
-#define SPD_EEPROM_ADDRESS1	0x52
-#define SPD_EEPROM_ADDRESS2	0x51
-#define CONFIG_DIMM_SLOTS_PER_CTLR	2
-#define CONFIG_CHIP_SELECTS_PER_CTRL	(2 * CONFIG_DIMM_SLOTS_PER_CTLR)
-#define CONFIG_MEM_INIT_VALUE	0xDeadBeef
-
-#define CONFIG_SYS_SDRAM_BASE	0x00000000	/* DDR is system memory*/
-#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL	(DDR_SDRAM_CLK_CNTL_SS_EN \
-					| DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05)
-/*
- * DDRCDR - DDR Control Driver Register
- */
-#define CONFIG_SYS_DDRCDR_VALUE	0x80080001
-
-#if defined(CONFIG_SPD_EEPROM)
-/*
- * Determine DDR configuration from I2C interface.
- */
-#define SPD_EEPROM_ADDRESS	0x51		/* DDR DIMM */
-#else
-/*
- * Manually set up DDR parameters
- */
-#define CONFIG_SYS_DDR_SIZE		256		/* MB */
-#define CONFIG_SYS_DDR_CS2_CONFIG	(CSCONFIG_EN \
-				| CSCONFIG_ROW_BIT_13 \
-				| CSCONFIG_COL_BIT_10)
-#define CONFIG_SYS_DDR_TIMING_1	0x36332321
-#define CONFIG_SYS_DDR_TIMING_2	0x00000800	/* P9-45,may need tuning */
-#define CONFIG_SYS_DDR_CONTROL	0xc2000000	/* unbuffered,no DYN_PWR */
-#define CONFIG_SYS_DDR_INTERVAL	0x04060100	/* autocharge,no open page */
-
-/* the default burst length is 4 - for 64-bit data path */
-				/* DLL,normal,seq,4/2.5, 4 burst len */
-#define CONFIG_SYS_DDR_MODE	0x00000022
-#endif
-
-/*
- * SDRAM on the Local Bus
- */
-#define CONFIG_SYS_LBC_SDRAM_BASE	0xF0000000	/* Localbus SDRAM */
-#define CONFIG_SYS_LBC_SDRAM_SIZE	64		/* LBC SDRAM is 64MB */
-
-/*
- * FLASH on the Local Bus
- */
-#define CONFIG_SYS_FLASH_BASE		0xFE000000	/* start of FLASH   */
-#define CONFIG_SYS_FLASH_SIZE		32	/* max flash size in MB */
-
-
-#define CONFIG_SYS_MAX_FLASH_BANKS	1	/* number of banks */
-#define CONFIG_SYS_MAX_FLASH_SECT	256	/* max sectors per device */
-
-#undef CONFIG_SYS_FLASH_CHECKSUM
-#define CONFIG_SYS_FLASH_ERASE_TOUT	60000	/* Flash Erase Timeout (ms) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (ms) */
-
-#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE	/* start of monitor */
-
-#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
-#define CONFIG_SYS_RAMBOOT
-#else
-#undef  CONFIG_SYS_RAMBOOT
-#endif
-
-/*
- * BCSR register on local bus 32KB, 8-bit wide for MDS config reg
- */
-#define CONFIG_SYS_BCSR			0xE2400000
-					/* Access window base at BCSR base */
-
-
-#define CONFIG_SYS_INIT_RAM_LOCK	1
-#define CONFIG_SYS_INIT_RAM_ADDR	0xFD000000	/* Initial RAM addr */
-#define CONFIG_SYS_INIT_RAM_SIZE	0x1000	/* Size of used area in RAM*/
-
-#define CONFIG_SYS_GBL_DATA_OFFSET	\
-			(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
-
-#define CONFIG_SYS_MONITOR_LEN	(512 * 1024)	/* Reserve 512 kB for Mon */
-
-/*
- * Serial Port
- */
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE    1
-#define CONFIG_SYS_NS16550_CLK		get_bus_freq(0)
-
-#define CONFIG_SYS_BAUDRATE_TABLE  \
-		{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
-
-#define CONFIG_SYS_NS16550_COM1        (CONFIG_SYS_IMMR+0x4500)
-#define CONFIG_SYS_NS16550_COM2        (CONFIG_SYS_IMMR+0x4600)
-
-/* I2C */
-#define CONFIG_SYS_I2C_NOPROBES		{ {0, 0x69} }
-
-/* SPI */
-#undef CONFIG_SOFT_SPI			/* SPI bit-banged */
-
-/* GPIOs.  Used as SPI chip selects */
-#define CONFIG_SYS_GPIO1_PRELIM
-#define CONFIG_SYS_GPIO1_DIR		0xC0000000  /* SPI CS on 0, LED on 1 */
-#define CONFIG_SYS_GPIO1_DAT		0xC0000000  /* Both are active LOW */
-
-/* TSEC */
-#define CONFIG_SYS_TSEC1_OFFSET 0x24000
-#define CONFIG_SYS_TSEC1	(CONFIG_SYS_IMMR+CONFIG_SYS_TSEC1_OFFSET)
-#define CONFIG_SYS_TSEC2_OFFSET 0x25000
-#define CONFIG_SYS_TSEC2	(CONFIG_SYS_IMMR+CONFIG_SYS_TSEC2_OFFSET)
-
-/* USB */
-#define CONFIG_SYS_USE_MPC834XSYS_USB_PHY	1 /* Use SYS board PHY */
-
-/*
- * General PCI
- * Addresses are mapped 1-1.
- */
-#define CONFIG_SYS_PCI1_MEM_BASE	0x80000000
-#define CONFIG_SYS_PCI1_MEM_PHYS	CONFIG_SYS_PCI1_MEM_BASE
-#define CONFIG_SYS_PCI1_MEM_SIZE	0x10000000	/* 256M */
-#define CONFIG_SYS_PCI1_MMIO_BASE	0x90000000
-#define CONFIG_SYS_PCI1_MMIO_PHYS	CONFIG_SYS_PCI1_MMIO_BASE
-#define CONFIG_SYS_PCI1_MMIO_SIZE	0x10000000	/* 256M */
-#define CONFIG_SYS_PCI1_IO_BASE		0x00000000
-#define CONFIG_SYS_PCI1_IO_PHYS		0xE2000000
-#define CONFIG_SYS_PCI1_IO_SIZE		0x00100000	/* 1M */
-
-#define CONFIG_SYS_PCI2_MEM_BASE	0xA0000000
-#define CONFIG_SYS_PCI2_MEM_PHYS	CONFIG_SYS_PCI2_MEM_BASE
-#define CONFIG_SYS_PCI2_MEM_SIZE	0x10000000	/* 256M */
-#define CONFIG_SYS_PCI2_MMIO_BASE	0xB0000000
-#define CONFIG_SYS_PCI2_MMIO_PHYS	CONFIG_SYS_PCI2_MMIO_BASE
-#define CONFIG_SYS_PCI2_MMIO_SIZE	0x10000000	/* 256M */
-#define CONFIG_SYS_PCI2_IO_BASE		0x00000000
-#define CONFIG_SYS_PCI2_IO_PHYS		0xE2100000
-#define CONFIG_SYS_PCI2_IO_SIZE		0x00100000	/* 1M */
-
-#if defined(CONFIG_PCI)
-
-#if !defined(CONFIG_PCI_PNP)
-	#define PCI_ENET0_IOADDR	0xFIXME
-	#define PCI_ENET0_MEMADDR	0xFIXME
-	#define PCI_IDSEL_NUMBER	0x0c	/* slot0->3(IDSEL)=12->15 */
-#endif
-
-#undef CONFIG_PCI_SCAN_SHOW		/* show pci devices on startup */
-
-#endif	/* CONFIG_PCI */
-
-/*
- * TSEC configuration
- */
-
-#if defined(CONFIG_TSEC_ENET)
-
-#define CONFIG_GMII		1	/* MII PHY management */
-#define CONFIG_TSEC1		1
-#define CONFIG_TSEC1_NAME	"TSEC0"
-#define CONFIG_TSEC2		1
-#define CONFIG_TSEC2_NAME	"TSEC1"
-#define TSEC1_PHY_ADDR		0
-#define TSEC2_PHY_ADDR		1
-#define TSEC1_PHYIDX		0
-#define TSEC2_PHYIDX		0
-#define TSEC1_FLAGS		TSEC_GIGABIT
-#define TSEC2_FLAGS		TSEC_GIGABIT
-
-/* Options are: TSEC[0-1] */
-#define CONFIG_ETHPRIME		"TSEC0"
-
-#endif	/* CONFIG_TSEC_ENET */
-
-/*
- * Configure on-board RTC
- */
-#define CONFIG_RTC_DS1374		/* use ds1374 rtc via i2c */
-#define CONFIG_SYS_I2C_RTC_ADDR	0x68	/* at address 0x68 */
-
-/*
- * Environment
- */
-#ifndef CONFIG_SYS_RAMBOOT
-/* Address and size of Redundant Environment Sector	*/
-#endif
-
-#define CONFIG_LOADS_ECHO	1	/* echo on for serial download */
-#define CONFIG_SYS_LOADS_BAUD_CHANGE	1	/* allow baudrate change */
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-
-#undef CONFIG_WATCHDOG			/* watchdog disabled */
-
-/*
- * Miscellaneous configurable options
- */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 256 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-				/* Initial Memory map for Linux*/
-#define CONFIG_SYS_BOOTMAPSZ	(256 << 20)
-#define CONFIG_SYS_BOOTM_LEN	(64 << 20)	/* Increase max gunzip size */
-
-#define CONFIG_SYS_RCWH_PCIHOST 0x80000000 /* PCIHOST  */
-
-/*
- * System performance
- */
-#define CONFIG_SYS_SCCR_TSEC1CM	1	/* TSEC1 clock mode (0-3) */
-#define CONFIG_SYS_SCCR_TSEC2CM	1	/* TSEC2 & I2C0 clock mode (0-3) */
-
-/* System IO Config */
-#define CONFIG_SYS_SICRH 0
-#define CONFIG_SYS_SICRL SICRL_LDP_A
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE	230400	/* speed of kgdb serial port */
-#endif
-
-/*
- * Environment Configuration
- */
-
-#if defined(CONFIG_TSEC_ENET)
-#define CONFIG_HAS_ETH1
-#define CONFIG_HAS_ETH0
-#endif
-
-#define CONFIG_HOSTNAME		"mpc8349emds"
-#define CONFIG_ROOTPATH		"/nfsroot/rootfs"
-#define CONFIG_BOOTFILE		"uImage"
-
-#define	CONFIG_EXTRA_ENV_SETTINGS					\
-	"netdev=eth0\0"							\
-	"hostname=mpc8349emds\0"					\
-	"nfsargs=setenv bootargs root=/dev/nfs rw "			\
-		"nfsroot=${serverip}:${rootpath}\0"			\
-	"ramargs=setenv bootargs root=/dev/ram rw\0"			\
-	"addip=setenv bootargs ${bootargs} "				\
-		"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"	\
-		":${hostname}:${netdev}:off panic=1\0"			\
-	"addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
-	"flash_nfs=run nfsargs addip addtty;"				\
-		"bootm ${kernel_addr}\0"				\
-	"flash_self=run ramargs addip addtty;"				\
-		"bootm ${kernel_addr} ${ramdisk_addr}\0"		\
-	"net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;"	\
-		"bootm\0"						\
-	"load=tftp 100000 /tftpboot/mpc8349emds/u-boot.bin\0"		\
-	"update=protect off fe000000 fe03ffff; "			\
-		"era fe000000 fe03ffff; cp.b 100000 fe000000 ${filesize}\0"\
-	"upd=run load update\0"						\
-	"fdtaddr=780000\0"						\
-	"fdtfile=mpc834x_mds.dtb\0"					\
-	""
-
-#define NFSBOOTCOMMAND						\
-	"setenv bootargs root=/dev/nfs rw "				\
-		"nfsroot=$serverip:$rootpath "				\
-		"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:"	\
-							"$netdev:off "	\
-		"console=$consoledev,$baudrate $othbootargs;"		\
-	"tftp $loadaddr $bootfile;"					\
-	"tftp $fdtaddr $fdtfile;"					\
-	"bootm $loadaddr - $fdtaddr"
-
-#define RAMBOOTCOMMAND						\
-	"setenv bootargs root=/dev/ram rw "				\
-		"console=$consoledev,$baudrate $othbootargs;"		\
-	"tftp $ramdiskaddr $ramdiskfile;"				\
-	"tftp $loadaddr $bootfile;"					\
-	"tftp $fdtaddr $fdtfile;"					\
-	"bootm $loadaddr $ramdiskaddr $fdtaddr"
-
-#define CONFIG_BOOTCOMMAND	"run flash_self"
-
-#endif	/* __CONFIG_H */