ppc: Remove MPC8308RDB board

This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.

Cc: Ilya Yanok <yanok@emcraft.com>
Signed-off-by: Tom Rini <trini@konsulko.com>

5 files changed, 0 insertions, 302 deletions

diff --git a/board/freescale/mpc8308rdb/Kconfig b/board/freescale/mpc8308rdb/Kconfig
deleted file mode 100644
index 48d25e5..0000000
--- a/board/freescale/mpc8308rdb/Kconfig
+++ /dev/null
@@ -1,12 +0,0 @@
-if TARGET_MPC8308RDB
-
-config SYS_BOARD
-	default "mpc8308rdb"
-
-config SYS_VENDOR
-	default "freescale"
-
-config SYS_CONFIG_NAME
-	default "MPC8308RDB"
-
-endif
diff --git a/board/freescale/mpc8308rdb/MAINTAINERS b/board/freescale/mpc8308rdb/MAINTAINERS
deleted file mode 100644
index 07ff2abd..0000000
--- a/board/freescale/mpc8308rdb/MAINTAINERS
+++ /dev/null
@@ -1,6 +0,0 @@
-MPC8308RDB BOARD
-M:	Ilya Yanok <yanok@emcraft.com>
-S:	Maintained
-F:	board/freescale/mpc8308rdb/
-F:	include/configs/MPC8308RDB.h
-F:	configs/MPC8308RDB_defconfig
diff --git a/board/freescale/mpc8308rdb/Makefile b/board/freescale/mpc8308rdb/Makefile
deleted file mode 100644
index d6eb4dc..0000000
--- a/board/freescale/mpc8308rdb/Makefile
+++ /dev/null
@@ -1,8 +0,0 @@
-# SPDX-License-Identifier: GPL-2.0+
-#
-# (C) Copyright 2006
-# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
-# (C) Copyright 2010
-# Ilya Yanok, Emcraft Systems, yanok@emcraft.com
-
-obj-y	:= mpc8308rdb.o sdram.o
diff --git a/board/freescale/mpc8308rdb/mpc8308rdb.c b/board/freescale/mpc8308rdb/mpc8308rdb.c
deleted file mode 100644
index db9c5ba..0000000
--- a/board/freescale/mpc8308rdb/mpc8308rdb.c
+++ /dev/null
@@ -1,192 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * Copyright (C) 2010 Freescale Semiconductor, Inc.
- * Copyright (C) 2010 Ilya Yanok, Emcraft Systems, yanok@emcraft.com
- */
-
-#include <common.h>
-#include <hwconfig.h>
-#include <i2c.h>
-#include <init.h>
-#include <net.h>
-#include <spi.h>
-#include <linux/delay.h>
-#include <linux/libfdt.h>
-#include <fdt_support.h>
-#include <pci.h>
-#include <mpc83xx.h>
-#include <vsc7385.h>
-#include <netdev.h>
-#include <fsl_esdhc.h>
-#include <asm/io.h>
-#include <asm/fsl_serdes.h>
-#include <asm/fsl_mpc83xx_serdes.h>
-
-/*
- * The following are used to control the SPI chip selects for the SPI command.
- */
-#ifdef CONFIG_MPC8XXX_SPI
-
-#define SPI_CS_MASK	0x00400000
-
-int spi_cs_is_valid(unsigned int bus, unsigned int cs)
-{
-	return bus == 0 && cs == 0;
-}
-
-void spi_cs_activate(struct spi_slave *slave)
-{
-	immap_t *immr = (immap_t *)CONFIG_SYS_IMMR;
-
-	/* active low */
-	clrbits_be32(&immr->gpio[0].dat, SPI_CS_MASK);
-}
-
-void spi_cs_deactivate(struct spi_slave *slave)
-{
-	immap_t *immr = (immap_t *)CONFIG_SYS_IMMR;
-
-	/* inactive high */
-	setbits_be32(&immr->gpio[0].dat, SPI_CS_MASK);
-}
-#endif /* CONFIG_MPC8XXX_SPI */
-
-#ifdef CONFIG_FSL_ESDHC
-int board_mmc_init(struct bd_info *bd)
-{
-	return fsl_esdhc_mmc_init(bd);
-}
-#endif
-
-static u8 read_board_info(void)
-{
-	u8 val8;
-	i2c_set_bus_num(0);
-
-	if (i2c_read(CONFIG_SYS_I2C_PCF8574A_ADDR, 0, 0, &val8, 1) == 0)
-		return val8;
-	else
-		return 0;
-}
-
-int checkboard(void)
-{
-	static const char * const rev_str[] = {
-		"1.0",
-		"<reserved>",
-		"<reserved>",
-		"<reserved>",
-		"<unknown>",
-	};
-	u8 info;
-	int i;
-
-	info = read_board_info();
-	i = (!info) ? 4 : info & 0x03;
-
-	printf("Board: Freescale MPC8308RDB Rev %s\n", rev_str[i]);
-
-	return 0;
-}
-
-static struct pci_region pcie_regions_0[] = {
-	{
-		.bus_start = CONFIG_SYS_PCIE1_MEM_BASE,
-		.phys_start = CONFIG_SYS_PCIE1_MEM_PHYS,
-		.size = CONFIG_SYS_PCIE1_MEM_SIZE,
-		.flags = PCI_REGION_MEM,
-	},
-	{
-		.bus_start = CONFIG_SYS_PCIE1_IO_BASE,
-		.phys_start = CONFIG_SYS_PCIE1_IO_PHYS,
-		.size = CONFIG_SYS_PCIE1_IO_SIZE,
-		.flags = PCI_REGION_IO,
-	},
-};
-
-void pci_init_board(void)
-{
-	immap_t *immr = (immap_t *)CONFIG_SYS_IMMR;
-	sysconf83xx_t *sysconf = &immr->sysconf;
-	law83xx_t *pcie_law = sysconf->pcielaw;
-	struct pci_region *pcie_reg[] = { pcie_regions_0 };
-
-	fsl_setup_serdes(CONFIG_FSL_SERDES1, FSL_SERDES_PROTO_PEX,
-					FSL_SERDES_CLK_100, FSL_SERDES_VDD_1V);
-
-	/* Deassert the resets in the control register */
-	out_be32(&sysconf->pecr1, 0xE0008000);
-	udelay(2000);
-
-	/* Configure PCI Express Local Access Windows */
-	out_be32(&pcie_law[0].bar, CONFIG_SYS_PCIE1_BASE & LAWBAR_BAR);
-	out_be32(&pcie_law[0].ar, LBLAWAR_EN | LBLAWAR_512MB);
-
-	mpc83xx_pcie_init(1, pcie_reg);
-}
-/*
- * Miscellaneous late-boot configurations
- *
- * If a VSC7385 microcode image is present, then upload it.
-*/
-int misc_init_r(void)
-{
-#ifdef CONFIG_MPC8XXX_SPI
-	immap_t *immr = (immap_t *)CONFIG_SYS_IMMR;
-	sysconf83xx_t *sysconf = &immr->sysconf;
-
-	/*
-	 * Set proper bits in SICRH to allow SPI on header J8
-	 *
-	 * NOTE: this breaks the TSEC2 interface, attached to the Vitesse
-	 * switch. The pinmux configuration does not have a fine enough
-	 * granularity to support both simultaneously.
-	 */
-	clrsetbits_be32(&sysconf->sicrh, SICRH_GPIO_A_TSEC2, SICRH_GPIO_A_GPIO);
-	puts("WARNING: SPI enabled, TSEC2 support is broken\n");
-
-	/* Set header J8 SPI chip select output, disabled */
-	setbits_be32(&immr->gpio[0].dir, SPI_CS_MASK);
-	setbits_be32(&immr->gpio[0].dat, SPI_CS_MASK);
-#endif
-
-#ifdef CONFIG_VSC7385_IMAGE
-	if (vsc7385_upload_firmware((void *) CONFIG_VSC7385_IMAGE,
-		CONFIG_VSC7385_IMAGE_SIZE)) {
-		puts("Failure uploading VSC7385 microcode.\n");
-		return 1;
-	}
-#endif
-
-	return 0;
-}
-#if defined(CONFIG_OF_BOARD_SETUP)
-int ft_board_setup(void *blob, struct bd_info *bd)
-{
-	ft_cpu_setup(blob, bd);
-	fsl_fdt_fixup_dr_usb(blob, bd);
-	fdt_fixup_esdhc(blob, bd);
-
-	return 0;
-}
-#endif
-
-int board_eth_init(struct bd_info *bis)
-{
-	int rv, num_if = 0;
-
-	/* Initialize TSECs first */
-	rv = cpu_eth_init(bis);
-	if (rv >= 0)
-		num_if += rv;
-	else
-		printf("ERROR: failed to initialize TSECs.\n");
-
-	rv = pci_eth_init(bis);
-	if (rv >= 0)
-		num_if += rv;
-	else
-		printf("ERROR: failed to initialize PCI Ethernet.\n");
-
-	return num_if;
-}
diff --git a/board/freescale/mpc8308rdb/sdram.c b/board/freescale/mpc8308rdb/sdram.c
deleted file mode 100644
index 6340fd1..0000000
--- a/board/freescale/mpc8308rdb/sdram.c
+++ /dev/null
@@ -1,84 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * Copyright (C) 2007 Freescale Semiconductor, Inc.
- * Copyright (C) 2010 Ilya Yanok, Emcraft Systems, yanok@emcraft.com
- *
- * Authors: Nick.Spence@freescale.com
- *          Wilson.Lo@freescale.com
- *          scottwood@freescale.com
- *
- * This files is  mostly identical to the original from
- * board\freescale\mpc8315erdb\sdram.c
- */
-
-#include <common.h>
-#include <init.h>
-#include <mpc83xx.h>
-#include <asm/global_data.h>
-
-#include <asm/bitops.h>
-#include <asm/io.h>
-
-#include <asm/processor.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-/* Fixed sdram init -- doesn't use serial presence detect.
- *
- * This is useful for faster booting in configs where the RAM is unlikely
- * to be changed, or for things like NAND booting where space is tight.
- */
-static long fixed_sdram(void)
-{
-	immap_t *im = (immap_t *)CONFIG_SYS_IMMR;
-	u32 msize = CONFIG_SYS_DDR_SIZE * 1024 * 1024;
-	u32 msize_log2 = __ilog2(msize);
-
-	out_be32(&im->sysconf.ddrlaw[0].bar,
-			CONFIG_SYS_SDRAM_BASE  & 0xfffff000);
-	out_be32(&im->sysconf.ddrlaw[0].ar, LBLAWAR_EN | (msize_log2 - 1));
-	out_be32(&im->sysconf.ddrcdr, CONFIG_SYS_DDRCDR_VALUE);
-
-	out_be32(&im->ddr.csbnds[0].csbnds, (msize - 1) >> 24);
-	out_be32(&im->ddr.cs_config[0], CONFIG_SYS_DDR_CS0_CONFIG);
-
-	/* Currently we use only one CS, so disable the other bank. */
-	out_be32(&im->ddr.cs_config[1], 0);
-
-	out_be32(&im->ddr.sdram_clk_cntl, CONFIG_SYS_DDR_SDRAM_CLK_CNTL);
-	out_be32(&im->ddr.timing_cfg_3, CONFIG_SYS_DDR_TIMING_3);
-	out_be32(&im->ddr.timing_cfg_1, CONFIG_SYS_DDR_TIMING_1);
-	out_be32(&im->ddr.timing_cfg_2, CONFIG_SYS_DDR_TIMING_2);
-	out_be32(&im->ddr.timing_cfg_0, CONFIG_SYS_DDR_TIMING_0);
-
-	out_be32(&im->ddr.sdram_cfg, CONFIG_SYS_DDR_SDRAM_CFG);
-	out_be32(&im->ddr.sdram_cfg2, CONFIG_SYS_DDR_SDRAM_CFG2);
-	out_be32(&im->ddr.sdram_mode, CONFIG_SYS_DDR_MODE);
-	out_be32(&im->ddr.sdram_mode2, CONFIG_SYS_DDR_MODE2);
-
-	out_be32(&im->ddr.sdram_interval, CONFIG_SYS_DDR_INTERVAL);
-	sync();
-
-	/* enable DDR controller */
-	setbits_be32(&im->ddr.sdram_cfg, SDRAM_CFG_MEM_EN);
-	sync();
-
-	return get_ram_size(CONFIG_SYS_SDRAM_BASE, msize);
-}
-
-int dram_init(void)
-{
-	immap_t *im = (immap_t *)CONFIG_SYS_IMMR;
-	u32 msize;
-
-	if ((in_be32(&im->sysconf.immrbar) & IMMRBAR_BASE_ADDR) != (u32)im)
-		return -ENXIO;
-
-	/* DDR SDRAM */
-	msize = fixed_sdram();
-
-	/* return total bus SDRAM size(bytes)  -- DDR */
-	gd->ram_size = msize;
-
-	return 0;
-}