Merge branch 'master' of git://git.denx.de/u-boot-mpc85xx

13 files changed, 912 insertions, 2 deletions

diff --git a/board/freescale/p1010rdb/README b/board/freescale/p1010rdb/README.P1010RDB-PA
index 7f18aaa..158a1b3 100644
--- a/board/freescale/p1010rdb/README
+++ b/board/freescale/p1010rdb/README.P1010RDB-PA
@@ -204,5 +204,5 @@ Place uImage, p1010rdb.dtb and rootfs files in the TFTP disk area.
 	=> bootm 1000000 3000000 2000000
 
 
-Please contact your local field applications engineer or sales representative
-to obtain related documents, such as P1010-RDB User Guide for details.
+For more details, please refer to P1010RDB User Guide and access website
+www.freescale.com
diff --git a/board/freescale/p1010rdb/README.P1010RDB-PB b/board/freescale/p1010rdb/README.P1010RDB-PB
new file mode 100644
index 0000000..cf459b3
--- /dev/null
+++ b/board/freescale/p1010rdb/README.P1010RDB-PB
@@ -0,0 +1,188 @@
+Overview
+=========
+The P1010RDB-PB is a Freescale Reference Design Board that hosts the P1010 SoC.
+P1010RDB-PB is a variation of previous P1010RDB-PA board.
+
+The P1010 is a cost-effective, low-power, highly integrated host processor
+based on a Power Architecture e500v2 core (maximum core frequency 1GHz),that
+addresses the requirements of several routing, gateways, storage, consumer,
+and industrial applications. Applications of interest include the main CPUs and
+I/O processors in network attached storage (NAS), the voice over IP (VoIP)
+router/gateway, and wireless LAN (WLAN) and industrial controllers.
+
+The P1010RDB-PB board features are as following:
+Memory subsystem:
+	- 1G bytes unbuffered DDR3 SDRAM discrete devices (32-bit bus)
+	- 32M bytes NOR flash single-chip memory
+	- 2G bytes NAND flash memory
+	- 16M bytes SPI memory
+	- 256K bit M24256 I2C EEPROM
+	- I2C Board EEPROM 128x8 bit memory
+	- SD/MMC connector to interface with the SD memory card
+Interfaces:
+	- Three 10/100/1000 BaseT Ethernet ports (One RGMII and two SGMII)
+	- PCIe 2.0: two x1 mini-PCIe slots
+	- SATA 2.0: two SATA interfaces
+	- USB 2.0: one USB interface
+	- FlexCAN: two FlexCAN interfaces (revision 2.0B)
+	- UART: one USB-to-Serial interface
+	- TDM: 2 FXS ports connected via an external SLIC to the TDM interface.
+	       1 FXO port connected via a relay to FXS for switchover to POTS
+
+Board connectors:
+	- Mini-ITX power supply connector
+	- JTAG/COP for debugging
+
+POR: support critical POR setting changed via switch on board
+PCB: 6-layer routing (4-layer signals, 2-layer power and ground)
+
+Physical Memory Map on P1010RDB
+===============================
+Address Start   Address End   Memory type	Attributes
+0x0000_0000	0x3fff_ffff   DDR		1G Cacheable
+0xa000_0000	0xdfff_ffff   PCI Express Mem	1G non-cacheable
+0xee00_0000	0xefff_ffff   NOR Flash		32M non-cacheable
+0xffc2_0000	0xffc5_ffff   PCI IO range	256K non-cacheable
+0xffa0_0000	0xffaf_ffff   NAND Flash	1M cacheable
+0xffb0_0000	0xffbf_ffff   Board CPLD	1M non-cacheable
+0xffd0_0000	0xffd0_3fff   L1 for Stack	16K Cacheable TLB0
+0xffe0_0000	0xffef_ffff   CCSR		1M non-cacheable
+
+
+Serial Port Configuration on P1010RDB
+=====================================
+Configure the serial port of the attached computer with the following values:
+	-Data rate: 115200 bps
+	-Number of data bits: 8
+	-Parity: None
+	-Number of Stop bits: 1
+	-Flow Control: Hardware/None
+
+
+P1010RDB-PB default DIP-switch settings
+=======================================
+SW1[1:8]= 10101010
+SW2[1:8]= 11011000
+SW3[1:8]= 10010000
+SW4[1:4]= 1010
+SW5[1:8]= 11111010
+
+
+P1010RDB-PB boot mode settings via DIP-switch
+=============================================
+SW4[1:4]= 1111 and SW3[3:4]= 00 for 16bit NOR boot
+SW4[1:4]= 1010 and SW3[3:4]= 01 for 8bit NAND boot
+SW4[1:4]= 0110 and SW3[3:4]= 00 for SPI boot
+SW4[1:4]= 0111 and SW3[3:4]= 10 for SD boot
+Note: 1 stands for 'on', 0 stands for 'off'
+
+
+Switch P1010RDB-PB boot mode via software without setting DIP-switch
+====================================================================
+=> run boot_bank0    (boot from NOR bank0)
+=> run boot_bank1    (boot from NOR bank1)
+=> run boot_nand     (boot from NAND flash)
+=> run boot_spi      (boot from SPI flash)
+=> run boot_sd       (boot from SD card)
+
+
+Frequency combination support on P1010RDB-PB
+=============================================
+SW1[4:7] SW5[1] SW5[5:8] SW2[2] Core(MHz) Platform(MHz) DDR(MT/s)
+0101      1      1010     0       800       400		800
+1001      1      1010     0       800       400		667
+1010      1      1100     0       667       333		667
+1000      0      1010     0       533       266		667
+0101      1      1010     1       1000      400		800
+1001      1      1010     1       1000      400		667
+
+
+Setting of pin mux
+==================
+Since pins multiplexing, TDM and CAN are muxed with SPI flash.
+SDHC is muxed with IFC. IFC and SPI flash are enabled by default.
+
+To enable TDM:
+=> setenv hwconfig fsl_p1010mux:tdm_can=tdm
+=> save;reset
+
+To enable FlexCAN:
+=> setenv hwconfig fsl_p1010mux:tdm_can=can
+=> save;reset
+
+To enable SDHC in case of NOR/NAND/SPI boot
+   a) For temporary use case in runtime without reboot system
+      run 'mux sdhc' in u-boot to validate SDHC with invalidating IFC.
+
+   b) For long-term use case
+      set 'esdhc' in hwconfig and save it.
+
+To enable IFC in case of SD boot
+   a) For temporary use case in runtime without reboot system
+      run 'mux ifc' in u-boot to validate IFC with invalidating SDHC.
+
+   b) For long-term use case
+      set 'ifc' in hwconfig and save it.
+
+
+Build images for different boot mode
+====================================
+First setup cross compile environment on build host
+   $ export ARCH=powerpc
+   $ export CROSS_COMPILE=<your-compiler-path>/powerpc-linux-gnu-
+
+1. For NOR boot
+   $ make P1010RDB-PB_NOR
+
+2. For NAND boot
+   $ make P1010RDB-PB_NAND
+
+3. For SPI boot
+   $ make P1010RDB-PB_SPIFLASH
+
+4. For SD boot
+   $ make P1010RDB-PB_SDCARD
+
+
+Steps to program images to flash for different boot mode
+========================================================
+1. NOR boot
+   => tftp 1000000 u-boot.bin
+   For bank0
+   => pro off all;era eff80000 efffffff;cp.b 1000000 eff80000 $filesize
+   set SW1[8]=0, SW4[1:4]= 1111 and SW3[3:4]= 00, then power on the board
+
+   For bank1
+   => pro off all;era eef80000 eeffffff;cp.b 1000000 eef80000 $filesize
+   set SW1[8]=1, SW4[1:4]= 1111 and SW3[3:4]= 00, then power on the board
+
+2. NAND boot
+   => tftp 1000000 u-boot-nand.bin
+   => nand erase 0 $filesize; nand write $loadaddr 0 $filesize
+   Set SW4[1:4]= 1010 and SW3[3:4]= 01, then power on the board
+
+3. SPI boot
+   1)  cat p1010rdb-config-header.bin u-boot.bin > u-boot-spi-combined.bin
+   2)  =>  tftp 1000000 u-boot-spi-combined.bin
+   3)  =>  sf probe 0; sf erase 0 100000; sf write 1000000 0 100000
+   set SW4[1:4]= 0110 and SW3[3:4]= 00, then power on the board
+
+4. SD boot
+   1)	cat p1010rdb-config-header.bin u-boot.bin > u-boot-sd-combined.bin
+   2)	=> tftp 1000000 u-boot-sd-combined.bin
+   3)	=> mux sdhc
+   4)	=> mmc write 1000000 0 1050
+   set SW4[1:4]= 0111 and SW3[3:4]= 10, then power on the board
+
+
+Boot Linux from network using TFTP on P1010RDB-PB
+=================================================
+Place uImage, p1010rdb.dtb and rootfs files in the TFTP download path.
+	=> tftp 1000000 uImage
+	=> tftp 2000000 p1010rdb.dtb
+	=> tftp 3000000 rootfs.ext2.gz.uboot.p1010rdb
+	=> bootm 1000000 3000000 2000000
+
+
+For more details, please refer to P1010RDB-PB User Guide and access website
+www.freescale.com and Freescale QorIQ SDK Infocenter document.
diff --git a/board/freescale/t1040qds/t1040_pbi.cfg b/board/freescale/t1040qds/t1040_pbi.cfg
new file mode 100644
index 0000000..624398a
--- /dev/null
+++ b/board/freescale/t1040qds/t1040_pbi.cfg
@@ -0,0 +1,27 @@
+#PBI commands
+#Initialize CPC1
+09010000 00200400
+09138000 00000000
+091380c0 00000100
+#Configure CPC1 as 512KB SRAM
+09010100 00000000
+09010104 fffc0007
+09010f00 08000000
+09010000 80000000
+#Configure LAW for CPC1
+09000cf0 00000000
+09000cf4 fffc0000
+09000cf8 81000011
+#Configure alternate space
+09000010 00000000
+09000014 ff000000
+09000018 81000000
+#Configure SPI controller
+09110000 80000403
+09110020 2d170008
+09110024 00100008
+09110028 00100008
+0911002c 00100008
+#Flush PBL data
+09138000 00000000
+091380c0 00000000
diff --git a/board/freescale/t1040qds/t1040_rcw.cfg b/board/freescale/t1040qds/t1040_rcw.cfg
new file mode 100644
index 0000000..0d0dfa5
--- /dev/null
+++ b/board/freescale/t1040qds/t1040_rcw.cfg
@@ -0,0 +1,7 @@
+#PBL preamble and RCW header
+aa55aa55 010e0100
+# serdes protocol 0x66
+0a10000c 0c000000 00000000 00000000
+66000002 00000000 fc027000 01000000
+00000000 00000000 00000000 00030810
+00000000 03fc500f 00000000 00000000
diff --git a/board/freescale/t104xrdb/Makefile b/board/freescale/t104xrdb/Makefile
new file mode 100644
index 0000000..76c0c94
--- /dev/null
+++ b/board/freescale/t104xrdb/Makefile
@@ -0,0 +1,12 @@
+#
+# Copyright 2013 Freescale Semiconductor, Inc.
+#
+# SPDX-License-Identifier:	GPL-2.0+
+#
+
+
+obj-y	+= t104xrdb.o
+obj-y	+= ddr.o
+obj-$(CONFIG_PCI)	+= pci.o
+obj-y	+= law.o
+obj-y	+= tlb.o
diff --git a/board/freescale/t104xrdb/README b/board/freescale/t104xrdb/README
new file mode 100644
index 0000000..2cd8219
--- /dev/null
+++ b/board/freescale/t104xrdb/README
@@ -0,0 +1,200 @@
+Overview
+--------
+The T1040RDB is a Freescale reference board that hosts the T1040 SoC
+(and variants). Variants inclued T1042 presonality of T1040, in which
+case T1040RDB can also be called T1042RDB.
+
+The T1042RDB_PI is a Freescale reference board that hosts the T1042 SoC.
+(a personality of T1040 SoC). The board is similar to T1040RDB but is
+designed specially with low power features targeted for Printing Image Market.
+
+T1040 SoC Overview
+------------------
+The QorIQ T1040/T1042 processor support four integrated 64-bit e5500 PA
+processor cores with high-performance data path acceleration architecture
+and network peripheral interfaces required for networking & telecommunications.
+
+The T1040/T1042 SoC includes the following function and features:
+
+ - Four e5500 cores, each with a private 256 KB L2 cache
+ - 256 KB shared L3 CoreNet platform cache (CPC)
+ - Interconnect CoreNet platform
+ - 32-/64-bit DDR3L/DDR4 SDRAM memory controller with ECC and interleaving
+   support
+ - Data Path Acceleration Architecture (DPAA) incorporating acceleration
+ for the following functions:
+    -  Packet parsing, classification, and distribution
+    -  Queue management for scheduling, packet sequencing, and congestion
+       management
+    -  Cryptography Acceleration (SEC 5.0)
+    - RegEx Pattern Matching Acceleration (PME 2.2)
+    - IEEE Std 1588 support
+    - Hardware buffer management for buffer allocation and deallocation
+ - Ethernet interfaces
+    - Integrated 8-port Gigabit Ethernet switch (T1040 only)
+    - Four 1 Gbps Ethernet controllers
+ - Two RGMII interfaces or one RGMII and one MII interfaces
+ - High speed peripheral interfaces
+   - Four PCI Express 2.0 controllers running at up to 5 GHz
+   - Two SATA controllers supporting 1.5 and 3.0 Gb/s operation
+   - Upto two QSGMII interface
+   - Upto six SGMII interface supporting 1000 Mbps
+   - One SGMII interface supporting upto 2500 Mbps
+ - Additional peripheral interfaces
+   - Two USB 2.0 controllers with integrated PHY
+   - SD/eSDHC/eMMC
+   - eSPI controller
+   - Four I2C controllers
+   - Four UARTs
+   - Four GPIO controllers
+   - Integrated flash controller (IFC)
+   - LCD and HDMI interface (DIU) with 12 bit dual data rate
+   - TDM interface
+ - Multicore programmable interrupt controller (PIC)
+ - Two 8-channel DMA engines
+ - Single source clocking implementation
+ - Deep Sleep power implementaion (wakeup from GPIO/Timer/Ethernet/USB)
+
+T1040 SoC Personalities
+-------------------------
+
+T1022 Personality:
+T1022 is a reduced personality of T1040 with less core/clusters.
+
+T1042 Personality:
+T1042 is a reduced personality of T1040 without Integrated 8-port Gigabit
+Ethernet switch. Rest of the blocks are same as T1040
+
+
+T1040RDB board Overview
+-------------------------
+ - SERDES Connections, 8 lanes information:
+	1: None
+	2: SGMII
+	3: QSGMII
+	4: QSGMII
+	5: PCIe1 x1 slot
+	6: mini PCIe connector
+	7: mini PCIe connector
+	8: SATA connector
+ - DDR Controller
+     - Supports rates of up to 1600 MHz data-rate
+     - Supports one DDR3LP UDIMM/RDIMMs, of single-, dual- or quad-rank types.
+ - IFC/Local Bus
+     - NAND flash: 1GB 8-bit NAND flash
+     - NOR: 128MB 16-bit NOR Flash
+ - Ethernet
+     - Two on-board RGMII 10/100/1G ethernet ports.
+ - CPLD
+ - Clocks
+     - System and DDR clock (SYSCLK, “DDRCLK”)
+     - SERDES clocks
+ - Power Supplies
+ - USB
+     - Supports two USB 2.0 ports with integrated PHYs
+     - Two type A ports with 5V@1.5A per port.
+ - SDHC
+     - SDHC/SDXC connector
+ - SPI
+    -  On-board 64MB SPI flash
+ - Other IO
+    - Two Serial ports
+    - Four I2C ports
+
+T1042RDB_PI board Overview
+-------------------------
+ - SERDES Connections, 8 lanes information:
+	1, 2, 3, 4 : PCIe x4 slot
+	5: mini PCIe connector
+	6: mini PCIe connector
+	7: NA
+	8: SATA connector
+ - DDR Controller
+     - Supports rates of up to 1600 MHz data-rate
+     - Supports one DDR3LP UDIMM/RDIMMs, of single-, dual- or quad-rank types.
+ - IFC/Local Bus
+     - NAND flash: 1GB 8-bit NAND flash
+     - NOR: 128MB 16-bit NOR Flash
+ - Ethernet
+     - Two on-board RGMII 10/100/1G ethernet ports.
+ - CPLD
+ - Clocks
+     - System and DDR clock (SYSCLK, “DDRCLK”)
+     - SERDES clocks
+ - Video
+     - DIU supports video at up to 1280x1024x32bpp
+ - Power Supplies
+ - USB
+     - Supports two USB 2.0 ports with integrated PHYs
+     - Two type A ports with 5V@1.5A per port.
+ - SDHC
+     - SDHC/SDXC connector
+ - SPI
+    -  On-board 64MB SPI flash
+ - Other IO
+    - Two Serial ports
+    - Four I2C ports
+
+Memory map
+-----------
+The addresses in brackets are physical addresses.
+
+Start Address  End Address      Description                     Size
+0xF_FFDF_0000  0xF_FFDF_0FFF    IFC - CPLD                      4KB
+0xF_FF80_0000  0xF_FF80_FFFF    IFC - NAND Flash                64KB
+0xF_FE00_0000  0xF_FEFF_FFFF    CCSRBAR                         16MB
+0xF_F803_0000  0xF_F803_FFFF    PCI Express 4 I/O Space         64KB
+0xF_F802_0000  0xF_F802_FFFF    PCI Express 3 I/O Space	        64KB
+0xF_F801_0000  0xF_F801_FFFF    PCI Express 2 I/O Space         64KB
+0xF_F800_0000  0xF_F800_FFFF    PCI Express 1 I/O Space	        64KB
+0xF_F600_0000  0xF_F7FF_FFFF    Queue manager software portal   32MB
+0xF_F400_0000  0xF_F5FF_FFFF    Buffer manager software portal  32MB
+0xF_E800_0000  0xF_EFFF_FFFF    IFC - NOR Flash                 128MB
+0xF_0000_0000  0xF_003F_FFFF    DCSR                            4MB
+0xC_3000_0000  0xC_3FFF_FFFF    PCI Express 4 Mem Space         256MB
+0xC_2000_0000  0xC_2FFF_FFFF    PCI Express 3 Mem Space         256MB
+0xC_1000_0000  0xC_1FFF_FFFF    PCI Express 2 Mem Space         256MB
+0xC_0000_0000  0xC_0FFF_FFFF    PCI Express 1 Mem Space         256MB
+0x0_0000_0000  0x0_ffff_ffff    DDR                             2GB
+
+
+NOR Flash memory Map
+---------------------
+ Start          End             Definition                       Size
+0xEFF80000      0xEFFFFFFF      u-boot (current bank)            512KB
+0xEFF60000      0xEFF7FFFF      u-boot env (current bank)        128KB
+0xEFF40000      0xEFF5FFFF      FMAN Ucode (current bank)        128KB
+0xED300000      0xEFF3FFFF      rootfs (alt bank)                44MB + 256KB
+0xEC800000      0xEC8FFFF       Hardware device tree (alt bank)  1MB
+0xEC020000      0xEC7FFFFF      Linux.uImage (alt bank)          7MB + 875KB
+0xEC000000      0xEC01FFFF      RCW (alt bank)                   128KB
+0xEBF80000      0xEBFFFFFF      u-boot (alt bank)                512KB
+0xEBF60000      0xEBF7FFFF      u-boot env (alt bank)            128KB
+0xEBF40000      0xEBF5FFFF      FMAN ucode (alt bank)            128KB
+0xE9300000      0xEBF3FFFF      rootfs (current bank)            44MB + 256KB
+0xE8800000      0xE88FFFFF      Hardware device tree (cur bank)  11MB + 512KB
+0xE8020000      0xE86FFFFF      Linux.uImage (current bank)      7MB + 875KB
+0xE8000000      0xE801FFFF      RCW (current bank)               128KB
+
+
+Various Software configurations/environment variables/commands
+--------------------------------------------------------------
+The below commands apply to the board
+
+1. U-boot environment variable hwconfig
+   The default hwconfig is:
+	hwconfig=fsl_ddr:ctlr_intlv=null,bank_intlv=cs0_cs1;usb1:
+					dr_mode=host,phy_type=utmi
+   Note: For USB gadget set "dr_mode=peripheral"
+
+2. FMAN Ucode versions
+   fsl_fman_ucode_t1040.bin
+
+3. Switching to alternate bank
+   Commands for switching to alternate bank.
+
+	1. To change from vbank0 to vbank4
+		=> qixis_reset altbank (it will boot using vbank4)
+
+	2.To change from vbank4 to vbank0
+		=> qixis reset (it will boot using vbank0)
diff --git a/board/freescale/t104xrdb/ddr.c b/board/freescale/t104xrdb/ddr.c
new file mode 100644
index 0000000..8f58dd6
--- /dev/null
+++ b/board/freescale/t104xrdb/ddr.c
@@ -0,0 +1,132 @@
+/*
+ * Copyright 2013 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <i2c.h>
+#include <hwconfig.h>
+#include <asm/mmu.h>
+#include <asm/fsl_ddr_sdram.h>
+#include <asm/fsl_ddr_dimm_params.h>
+#include <asm/fsl_law.h>
+#include "ddr.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int fsl_ddr_get_dimm_params(dimm_params_t *pdimm,
+		unsigned int controller_number,
+		unsigned int dimm_number)
+{
+	const char dimm_model[] = "RAW timing DDR";
+
+	if ((controller_number == 0) && (dimm_number == 0)) {
+		memcpy(pdimm, &ddr_raw_timing, sizeof(dimm_params_t));
+		memset(pdimm->mpart, 0, sizeof(pdimm->mpart));
+		memcpy(pdimm->mpart, dimm_model, sizeof(dimm_model) - 1);
+	}
+
+	return 0;
+}
+
+void fsl_ddr_board_options(memctl_options_t *popts,
+				dimm_params_t *pdimm,
+				unsigned int ctrl_num)
+{
+	const struct board_specific_parameters *pbsp, *pbsp_highest = NULL;
+	ulong ddr_freq;
+
+	if (ctrl_num > 1) {
+		printf("Not supported controller number %d\n", ctrl_num);
+		return;
+	}
+	if (!pdimm->n_ranks)
+		return;
+
+	pbsp = udimms[0];
+
+	/* Get clk_adjust, cpo, write_data_delay,2t, according to the board ddr
+	 * freqency and n_banks specified in board_specific_parameters table.
+	 */
+	ddr_freq = get_ddr_freq(0) / 1000000;
+	while (pbsp->datarate_mhz_high) {
+		if (pbsp->n_ranks == pdimm->n_ranks &&
+		    (pdimm->rank_density >> 30) >= pbsp->rank_gb) {
+			if (ddr_freq <= pbsp->datarate_mhz_high) {
+				popts->cpo_override = pbsp->cpo;
+				popts->write_data_delay =
+					pbsp->write_data_delay;
+				popts->clk_adjust = pbsp->clk_adjust;
+				popts->wrlvl_start = pbsp->wrlvl_start;
+				popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2;
+				popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3;
+				popts->twot_en = pbsp->force_2t;
+				goto found;
+			}
+			pbsp_highest = pbsp;
+		}
+		pbsp++;
+	}
+
+	if (pbsp_highest) {
+		printf("Error: board specific timing not found\n");
+		printf("for data rate %lu MT/s\n", ddr_freq);
+		printf("Trying to use the highest speed (%u) parameters\n",
+		       pbsp_highest->datarate_mhz_high);
+		popts->cpo_override = pbsp_highest->cpo;
+		popts->write_data_delay = pbsp_highest->write_data_delay;
+		popts->clk_adjust = pbsp_highest->clk_adjust;
+		popts->wrlvl_start = pbsp_highest->wrlvl_start;
+		popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2;
+		popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3;
+		popts->twot_en = pbsp_highest->force_2t;
+	} else {
+		panic("DIMM is not supported by this board");
+	}
+found:
+	debug("Found timing match: n_ranks %d, data rate %d, rank_gb %d\n"
+		"\tclk_adjust %d, wrlvl_start %d, wrlvl_ctrl_2 0x%x, "
+		"wrlvl_ctrl_3 0x%x\n",
+		pbsp->n_ranks, pbsp->datarate_mhz_high, pbsp->rank_gb,
+		pbsp->clk_adjust, pbsp->wrlvl_start, pbsp->wrlvl_ctl_2,
+		pbsp->wrlvl_ctl_3);
+
+	/*
+	 * Factors to consider for half-strength driver enable:
+	 *	- number of DIMMs installed
+	 */
+	popts->half_strength_driver_enable = 0;
+	/*
+	 * Write leveling override
+	 */
+	popts->wrlvl_override = 1;
+	popts->wrlvl_sample = 0xf;
+
+	/*
+	 * rtt and rtt_wr override
+	 */
+	popts->rtt_override = 0;
+
+	/* Enable ZQ calibration */
+	popts->zq_en = 1;
+
+	/* DHC_EN =1, ODT = 75 Ohm */
+	popts->ddr_cdr1 = DDR_CDR1_DHC_EN | DDR_CDR1_ODT(DDR_CDR_ODT_75ohm);
+	popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_75ohm);
+}
+
+phys_size_t initdram(int board_type)
+{
+	phys_size_t dram_size;
+
+	puts("Initializing....using SPD\n");
+
+	dram_size = fsl_ddr_sdram();
+
+	dram_size = setup_ddr_tlbs(dram_size / 0x100000);
+	dram_size *= 0x100000;
+
+	puts("    DDR: ");
+	return dram_size;
+}
diff --git a/board/freescale/t104xrdb/ddr.h b/board/freescale/t104xrdb/ddr.h
new file mode 100644
index 0000000..9276b59
--- /dev/null
+++ b/board/freescale/t104xrdb/ddr.h
@@ -0,0 +1,76 @@
+/*
+ * Copyright 2013 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#ifndef __DDR_H__
+#define __DDR_H__
+
+dimm_params_t ddr_raw_timing = {
+	.n_ranks = 2,
+	.rank_density = 2147483648u,
+	.capacity = 4294967296u,
+	.primary_sdram_width = 64,
+	.ec_sdram_width = 8,
+	.registered_dimm = 0,
+	.mirrored_dimm = 1,
+	.n_row_addr = 15,
+	.n_col_addr = 10,
+	.n_banks_per_sdram_device = 8,
+	.edc_config = 2,	/* ECC */
+	.burst_lengths_bitmask = 0x0c,
+
+	.tckmin_x_ps = 1071,
+	.caslat_x = 0x2fe << 4,	/* 5,6,7,8,9,10,11,13 */
+	.taa_ps = 13910,
+	.twr_ps = 15000,
+	.trcd_ps = 13910,
+	.trrd_ps = 6000,
+	.trp_ps = 13910,
+	.tras_ps = 34000,
+	.trc_ps = 48910,
+	.trfc_ps = 260000,
+	.twtr_ps = 7500,
+	.trtp_ps = 7500,
+	.refresh_rate_ps = 7800000,
+	.tfaw_ps = 35000,
+};
+
+struct board_specific_parameters {
+	u32 n_ranks;
+	u32 datarate_mhz_high;
+	u32 rank_gb;
+	u32 clk_adjust;
+	u32 wrlvl_start;
+	u32 wrlvl_ctl_2;
+	u32 wrlvl_ctl_3;
+	u32 cpo;
+	u32 write_data_delay;
+	u32 force_2t;
+};
+
+/*
+ * These tables contain all valid speeds we want to override with board
+ * specific parameters. datarate_mhz_high values need to be in ascending order
+ * for each n_ranks group.
+ */
+
+static const struct board_specific_parameters udimm0[] = {
+	/*
+	 * memory controller 0
+	 *   num|  hi| rank|  clk| wrlvl |   wrlvl   |  wrlvl | cpo  |wrdata|2T
+	 * ranks| mhz| GB  |adjst| start |   ctl2    |  ctl3  |      |delay |
+	 */
+	{2,  1066, 4, 8,     4, 0x05070609, 0x08090a08,   0xff,    2,  0},
+	{2,  1350, 4, 4,     8, 0x0809090b, 0x0c0c0d0a,   0xff,    2,  0},
+	{2,  1350, 0, 5,     7, 0x0709090b, 0x0c0c0d09,   0xff,    2,  0},
+	{2,  1666, 4, 4,     8, 0x080a0a0d, 0x0d10100b,   0xff,    2,  0},
+	{2,  1666, 0, 5,     7, 0x080a0a0c, 0x0d0d0e0a,   0xff,    2,  0},
+	{}
+};
+
+static const struct board_specific_parameters *udimms[] = {
+	udimm0,
+};
+#endif
diff --git a/board/freescale/t104xrdb/law.c b/board/freescale/t104xrdb/law.c
new file mode 100644
index 0000000..2362d43
--- /dev/null
+++ b/board/freescale/t104xrdb/law.c
@@ -0,0 +1,32 @@
+/*
+ * Copyright 2013 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/fsl_law.h>
+#include <asm/mmu.h>
+
+struct law_entry law_table[] = {
+#ifndef CONFIG_SYS_NO_FLASH
+	SET_LAW(CONFIG_SYS_FLASH_BASE_PHYS, LAW_SIZE_256M, LAW_TRGT_IF_IFC),
+#endif
+#ifdef CONFIG_SYS_BMAN_MEM_PHYS
+	SET_LAW(CONFIG_SYS_BMAN_MEM_PHYS, LAW_SIZE_32M, LAW_TRGT_IF_BMAN),
+#endif
+#ifdef CONFIG_SYS_QMAN_MEM_PHYS
+	SET_LAW(CONFIG_SYS_QMAN_MEM_PHYS, LAW_SIZE_32M, LAW_TRGT_IF_QMAN),
+#endif
+#ifdef CONFIG_SYS_CPLD_BASE_PHYS
+	SET_LAW(CONFIG_SYS_CPLD_BASE_PHYS, LAW_SIZE_128K, LAW_TRGT_IF_IFC),
+#endif
+#ifdef CONFIG_SYS_DCSRBAR_PHYS
+	SET_LAW(CONFIG_SYS_DCSRBAR_PHYS, LAW_SIZE_4M, LAW_TRGT_IF_DCSR),
+#endif
+#ifdef CONFIG_SYS_NAND_BASE_PHYS
+	SET_LAW(CONFIG_SYS_NAND_BASE_PHYS, LAW_SIZE_64K, LAW_TRGT_IF_IFC),
+#endif
+};
+
+int num_law_entries = ARRAY_SIZE(law_table);
diff --git a/board/freescale/t104xrdb/pci.c b/board/freescale/t104xrdb/pci.c
new file mode 100644
index 0000000..c53e3b7
--- /dev/null
+++ b/board/freescale/t104xrdb/pci.c
@@ -0,0 +1,23 @@
+/*
+ * Copyright 2013 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <command.h>
+#include <pci.h>
+#include <asm/fsl_pci.h>
+#include <libfdt.h>
+#include <fdt_support.h>
+#include <asm/fsl_serdes.h>
+
+void pci_init_board(void)
+{
+	fsl_pcie_init_board(0);
+}
+
+void pci_of_setup(void *blob, bd_t *bd)
+{
+	FT_FSL_PCI_SETUP;
+}
diff --git a/board/freescale/t104xrdb/t104xrdb.c b/board/freescale/t104xrdb/t104xrdb.c
new file mode 100644
index 0000000..6e29d64
--- /dev/null
+++ b/board/freescale/t104xrdb/t104xrdb.c
@@ -0,0 +1,93 @@
+/*
+ * Copyright 2013 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <command.h>
+#include <netdev.h>
+#include <linux/compiler.h>
+#include <asm/mmu.h>
+#include <asm/processor.h>
+#include <asm/cache.h>
+#include <asm/immap_85xx.h>
+#include <asm/fsl_law.h>
+#include <asm/fsl_serdes.h>
+#include <asm/fsl_portals.h>
+#include <asm/fsl_liodn.h>
+#include <fm_eth.h>
+
+#include "t104xrdb.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int checkboard(void)
+{
+	struct cpu_type *cpu = gd->arch.cpu;
+
+	printf("Board: %sRDB\n", cpu->name);
+	return 0;
+}
+
+int board_early_init_r(void)
+{
+#ifdef CONFIG_SYS_FLASH_BASE
+	const unsigned int flashbase = CONFIG_SYS_FLASH_BASE;
+	const u8 flash_esel = find_tlb_idx((void *)flashbase, 1);
+
+	/*
+	 * Remap Boot flash region to caching-inhibited
+	 * so that flash can be erased properly.
+	 */
+
+	/* Flush d-cache and invalidate i-cache of any FLASH data */
+	flush_dcache();
+	invalidate_icache();
+
+	/* invalidate existing TLB entry for flash */
+	disable_tlb(flash_esel);
+
+	set_tlb(1, flashbase, CONFIG_SYS_FLASH_BASE_PHYS,
+		MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+		0, flash_esel, BOOKE_PAGESZ_256M, 1);
+#endif
+	set_liodns();
+#ifdef CONFIG_SYS_DPAA_QBMAN
+	setup_portals();
+#endif
+
+	return 0;
+}
+
+int misc_init_r(void)
+{
+	return 0;
+}
+
+void ft_board_setup(void *blob, bd_t *bd)
+{
+	phys_addr_t base;
+	phys_size_t size;
+
+	ft_cpu_setup(blob, bd);
+
+	base = getenv_bootm_low();
+	size = getenv_bootm_size();
+
+	fdt_fixup_memory(blob, (u64)base, (u64)size);
+
+#ifdef CONFIG_PCI
+	pci_of_setup(blob, bd);
+#endif
+
+	fdt_fixup_liodn(blob);
+
+#ifdef CONFIG_HAS_FSL_DR_USB
+	fdt_fixup_dr_usb(blob, bd);
+#endif
+
+#ifdef CONFIG_SYS_DPAA_FMAN
+	fdt_fixup_fman_ethernet(blob);
+#endif
+}
diff --git a/board/freescale/t104xrdb/t104xrdb.h b/board/freescale/t104xrdb/t104xrdb.h
new file mode 100644
index 0000000..e7cc0c7
--- /dev/null
+++ b/board/freescale/t104xrdb/t104xrdb.h
@@ -0,0 +1,13 @@
+/*
+ * Copyright 2013 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#ifndef __T104x_RDB_H__
+#define __T104x_RDB_H__
+
+void fdt_fixup_board_enet(void *blob);
+void pci_of_setup(void *blob, bd_t *bd);
+
+#endif
diff --git a/board/freescale/t104xrdb/tlb.c b/board/freescale/t104xrdb/tlb.c
new file mode 100644
index 0000000..84f97a4
--- /dev/null
+++ b/board/freescale/t104xrdb/tlb.c
@@ -0,0 +1,107 @@
+/*
+ * Copyright 2013 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/mmu.h>
+
+struct fsl_e_tlb_entry tlb_table[] = {
+	/* TLB 0 - for temp stack in cache */
+	SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR,
+		      CONFIG_SYS_INIT_RAM_ADDR_PHYS,
+		      MAS3_SX|MAS3_SW|MAS3_SR, 0,
+		      0, 0, BOOKE_PAGESZ_4K, 0),
+	SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024,
+		      CONFIG_SYS_INIT_RAM_ADDR_PHYS + 4 * 1024,
+		      MAS3_SX|MAS3_SW|MAS3_SR, 0,
+		      0, 0, BOOKE_PAGESZ_4K, 0),
+	SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024,
+		      CONFIG_SYS_INIT_RAM_ADDR_PHYS + 8 * 1024,
+		      MAS3_SX|MAS3_SW|MAS3_SR, 0,
+		      0, 0, BOOKE_PAGESZ_4K, 0),
+	SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024,
+		      CONFIG_SYS_INIT_RAM_ADDR_PHYS + 12 * 1024,
+		      MAS3_SX|MAS3_SW|MAS3_SR, 0,
+		      0, 0, BOOKE_PAGESZ_4K, 0),
+
+	/* TLB 1 */
+	/* *I*** - Covers boot page */
+#if defined(CONFIG_SYS_RAMBOOT) && defined(CONFIG_SYS_INIT_L3_ADDR)
+	/*
+	 * *I*G - L3SRAM. When L3 is used as 256K SRAM, the address of the
+	 * SRAM is at 0xfffc0000, it covered the 0xfffff000.
+	 */
+	SET_TLB_ENTRY(1, CONFIG_SYS_INIT_L3_ADDR, CONFIG_SYS_INIT_L3_ADDR,
+		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+		      0, 0, BOOKE_PAGESZ_256K, 1),
+#else
+	SET_TLB_ENTRY(1, 0xfffff000, 0xfffff000,
+		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+		      0, 0, BOOKE_PAGESZ_4K, 1),
+#endif
+
+	/* *I*G* - CCSRBAR */
+	SET_TLB_ENTRY(1, CONFIG_SYS_CCSRBAR, CONFIG_SYS_CCSRBAR_PHYS,
+		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+		      0, 1, BOOKE_PAGESZ_16M, 1),
+
+	/* *I*G* - Flash, localbus */
+	/* This will be changed to *I*G* after relocation to RAM. */
+	SET_TLB_ENTRY(1, CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE_PHYS,
+		      MAS3_SX|MAS3_SR, MAS2_W|MAS2_G,
+		      0, 2, BOOKE_PAGESZ_256M, 1),
+
+	/* *I*G* - PCI */
+	SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_MEM_VIRT, CONFIG_SYS_PCIE1_MEM_PHYS,
+		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+		      0, 3, BOOKE_PAGESZ_1G, 1),
+
+	/* *I*G* - PCI I/O */
+	SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_IO_VIRT, CONFIG_SYS_PCIE1_IO_PHYS,
+		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+		      0, 4, BOOKE_PAGESZ_256K, 1),
+
+	/* Bman/Qman */
+#ifdef CONFIG_SYS_BMAN_MEM_PHYS
+	SET_TLB_ENTRY(1, CONFIG_SYS_BMAN_MEM_BASE, CONFIG_SYS_BMAN_MEM_PHYS,
+		      MAS3_SX|MAS3_SW|MAS3_SR, 0,
+		      0, 5, BOOKE_PAGESZ_16M, 1),
+	SET_TLB_ENTRY(1, CONFIG_SYS_BMAN_MEM_BASE + 0x01000000,
+		      CONFIG_SYS_BMAN_MEM_PHYS + 0x01000000,
+		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+		      0, 6, BOOKE_PAGESZ_16M, 1),
+#endif
+#ifdef CONFIG_SYS_QMAN_MEM_PHYS
+	SET_TLB_ENTRY(1, CONFIG_SYS_QMAN_MEM_BASE, CONFIG_SYS_QMAN_MEM_PHYS,
+		      MAS3_SX|MAS3_SW|MAS3_SR, 0,
+		      0, 7, BOOKE_PAGESZ_16M, 1),
+	SET_TLB_ENTRY(1, CONFIG_SYS_QMAN_MEM_BASE + 0x01000000,
+		      CONFIG_SYS_QMAN_MEM_PHYS + 0x01000000,
+		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+		      0, 8, BOOKE_PAGESZ_16M, 1),
+#endif
+#ifdef CONFIG_SYS_DCSRBAR_PHYS
+	SET_TLB_ENTRY(1, CONFIG_SYS_DCSRBAR, CONFIG_SYS_DCSRBAR_PHYS,
+		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+		      0, 9, BOOKE_PAGESZ_4M, 1),
+#endif
+#ifdef CONFIG_SYS_NAND_BASE
+	/*
+	 * *I*G - NAND
+	 * entry 14 and 15 has been used hard coded, they will be disabled
+	 * in cpu_init_f, so we use entry 16 for nand.
+	 */
+	SET_TLB_ENTRY(1, CONFIG_SYS_NAND_BASE, CONFIG_SYS_NAND_BASE_PHYS,
+		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+		      0, 10, BOOKE_PAGESZ_64K, 1),
+#endif
+#ifdef CONFIG_SYS_CPLD_BASE
+	SET_TLB_ENTRY(1, CONFIG_SYS_CPLD_BASE, CONFIG_SYS_CPLD_BASE_PHYS,
+		      MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+		      0, 11, BOOKE_PAGESZ_256K, 1),
+#endif
+};
+
+int num_tlb_entries = ARRAY_SIZE(tlb_table);