diff options
author | Vladimir Barinov <vladimir.barinov@cogentembedded.com> | 2015-07-20 20:49:59 +0300 |
---|---|---|
committer | Nobuhiro Iwamatsu <iwamatsu@nigauri.org> | 2015-08-31 17:32:59 +0900 |
commit | 21871138b7686b36dd8ae97cab5dc1e9c5c6e183 (patch) | |
tree | e44c863566f312a23394dfc10560e4192f7707bc /board/renesas/stout/stout.c | |
parent | b8f91e2c92b7a8e01234fe384186202a24238f92 (diff) | |
download | u-boot-21871138b7686b36dd8ae97cab5dc1e9c5c6e183.zip u-boot-21871138b7686b36dd8ae97cab5dc1e9c5c6e183.tar.gz u-boot-21871138b7686b36dd8ae97cab5dc1e9c5c6e183.tar.bz2 |
arm: rmobile: Add Stout board support
Stout is an entry level development board based on R-Car H2 SoC (R8A7790)
This commit supports the following peripherals:
- SCIFA, I2C, Ethernet, QSPI, SDHI0/2, CPLD
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Diffstat (limited to 'board/renesas/stout/stout.c')
-rw-r--r-- | board/renesas/stout/stout.c | 232 |
1 files changed, 232 insertions, 0 deletions
diff --git a/board/renesas/stout/stout.c b/board/renesas/stout/stout.c new file mode 100644 index 0000000..7df7394 --- /dev/null +++ b/board/renesas/stout/stout.c @@ -0,0 +1,232 @@ +/* + * board/renesas/stout/stout.c + * This file is Stout board support. + * + * Copyright (C) 2015 Renesas Electronics Europe GmbH + * Copyright (C) 2015 Renesas Electronics Corporation + * Copyright (C) 2015 Cogent Embedded, Inc. + * + * SPDX-License-Identifier: GPL-2.0 + */ + +#include <common.h> +#include <malloc.h> +#include <netdev.h> +#include <dm.h> +#include <dm/platform_data/serial_sh.h> +#include <asm/processor.h> +#include <asm/mach-types.h> +#include <asm/io.h> +#include <asm/errno.h> +#include <asm/arch/sys_proto.h> +#include <asm/gpio.h> +#include <asm/arch/rmobile.h> +#include <asm/arch/rcar-mstp.h> +#include <asm/arch/mmc.h> +#include <asm/arch/sh_sdhi.h> +#include <miiphy.h> +#include <i2c.h> +#include <mmc.h> +#include "qos.h" +#include "cpld.h" + +DECLARE_GLOBAL_DATA_PTR; + +#define CLK2MHZ(clk) (clk / 1000 / 1000) +void s_init(void) +{ + struct rcar_rwdt *rwdt = (struct rcar_rwdt *)RWDT_BASE; + struct rcar_swdt *swdt = (struct rcar_swdt *)SWDT_BASE; + + /* Watchdog init */ + writel(0xA5A5A500, &rwdt->rwtcsra); + writel(0xA5A5A500, &swdt->swtcsra); + + /* CPU frequency setting. Set to 1.4GHz */ + if (rmobile_get_cpu_rev_integer() >= R8A7790_CUT_ES2X) { + u32 stat = 0; + u32 stc = ((1400 / CLK2MHZ(CONFIG_SYS_CLK_FREQ)) - 1) + << PLL0_STC_BIT; + clrsetbits_le32(PLL0CR, PLL0_STC_MASK, stc); + + do { + stat = readl(PLLECR) & PLL0ST; + } while (stat == 0x0); + } + + /* QoS(Quality-of-Service) Init */ + qos_init(); +} + +#define TMU0_MSTP125 (1 << 25) +#define SCIFA0_MSTP204 (1 << 4) +#define SDHI0_MSTP314 (1 << 14) +#define SDHI2_MSTP312 (1 << 12) +#define ETHER_MSTP813 (1 << 13) + +#define MSTPSR3 0xE6150048 +#define SMSTPCR3 0xE615013C + +#define SD2CKCR 0xE6150078 +#define SD2_97500KHZ 0x7 + +int board_early_init_f(void) +{ + /* TMU0 */ + mstp_clrbits_le32(MSTPSR1, SMSTPCR1, TMU0_MSTP125); + /* SCIFA0 */ + mstp_clrbits_le32(MSTPSR2, SMSTPCR2, SCIFA0_MSTP204); + /* ETHER */ + mstp_clrbits_le32(MSTPSR8, SMSTPCR8, ETHER_MSTP813); + /* SDHI0,2 */ + mstp_clrbits_le32(MSTPSR3, SMSTPCR3, SDHI0_MSTP314 | SDHI2_MSTP312); + + /* + * SD0 clock is set to 97.5MHz by default. + * Set SD2 to the 97.5MHz as well. + */ + writel(SD2_97500KHZ, SD2CKCR); + + return 0; +} + +int board_init(void) +{ + /* adress of boot parameters */ + gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100; + + /* Init PFC controller */ + r8a7790_pinmux_init(); + + cpld_init(); + +#ifdef CONFIG_SH_ETHER + /* ETHER Enable */ + gpio_request(GPIO_FN_ETH_CRS_DV, NULL); + gpio_request(GPIO_FN_ETH_RX_ER, NULL); + gpio_request(GPIO_FN_ETH_RXD0, NULL); + gpio_request(GPIO_FN_ETH_RXD1, NULL); + gpio_request(GPIO_FN_ETH_LINK, NULL); + gpio_request(GPIO_FN_ETH_REF_CLK, NULL); + gpio_request(GPIO_FN_ETH_MDIO, NULL); + gpio_request(GPIO_FN_ETH_TXD1, NULL); + gpio_request(GPIO_FN_ETH_TX_EN, NULL); + gpio_request(GPIO_FN_ETH_MAGIC, NULL); + gpio_request(GPIO_FN_ETH_TXD0, NULL); + gpio_request(GPIO_FN_ETH_MDC, NULL); + gpio_request(GPIO_FN_IRQ1, NULL); + + gpio_request(GPIO_GP_3_31, NULL); /* PHY_RST */ + gpio_direction_output(GPIO_GP_3_31, 0); + mdelay(20); + gpio_set_value(GPIO_GP_3_31, 1); + udelay(1); +#endif + + return 0; +} + +#define CXR24 0xEE7003C0 /* MAC address high register */ +#define CXR25 0xEE7003C8 /* MAC address low register */ +int board_eth_init(bd_t *bis) +{ + int ret = -ENODEV; + +#ifdef CONFIG_SH_ETHER + u32 val; + unsigned char enetaddr[6]; + + ret = sh_eth_initialize(bis); + if (!eth_getenv_enetaddr("ethaddr", enetaddr)) + return ret; + + /* Set Mac address */ + val = enetaddr[0] << 24 | enetaddr[1] << 16 | + enetaddr[2] << 8 | enetaddr[3]; + writel(val, CXR24); + + val = enetaddr[4] << 8 | enetaddr[5]; + writel(val, CXR25); +#endif + + return ret; +} + +/* Stout has KSZ8041NL/RNL */ +#define PHY_CONTROL1 0x1E +#define PHY_LED_MODE 0xC0000 +#define PHY_LED_MODE_ACK 0x4000 +int board_phy_config(struct phy_device *phydev) +{ + int ret = phy_read(phydev, MDIO_DEVAD_NONE, PHY_CONTROL1); + ret &= ~PHY_LED_MODE; + ret |= PHY_LED_MODE_ACK; + ret = phy_write(phydev, MDIO_DEVAD_NONE, PHY_CONTROL1, (u16)ret); + + return 0; +} + +int board_mmc_init(bd_t *bis) +{ + int ret = -ENODEV; + +#ifdef CONFIG_SH_SDHI + gpio_request(GPIO_FN_SD0_DAT0, NULL); + gpio_request(GPIO_FN_SD0_DAT1, NULL); + gpio_request(GPIO_FN_SD0_DAT2, NULL); + gpio_request(GPIO_FN_SD0_DAT3, NULL); + gpio_request(GPIO_FN_SD0_CLK, NULL); + gpio_request(GPIO_FN_SD0_CMD, NULL); + gpio_request(GPIO_FN_SD0_CD, NULL); + gpio_request(GPIO_FN_SD2_DAT0, NULL); + gpio_request(GPIO_FN_SD2_DAT1, NULL); + gpio_request(GPIO_FN_SD2_DAT2, NULL); + gpio_request(GPIO_FN_SD2_DAT3, NULL); + gpio_request(GPIO_FN_SD2_CLK, NULL); + gpio_request(GPIO_FN_SD2_CMD, NULL); + gpio_request(GPIO_FN_SD2_CD, NULL); + + /* SDHI0 - needs CPLD mux setup */ + gpio_request(GPIO_GP_3_30, NULL); + gpio_direction_output(GPIO_GP_3_30, 1); /* VLDO3=3.3V */ + gpio_request(GPIO_GP_5_24, NULL); + gpio_direction_output(GPIO_GP_5_24, 1); /* power on */ + + ret = sh_sdhi_init(CONFIG_SYS_SH_SDHI0_BASE, 0, + SH_SDHI_QUIRK_16BIT_BUF); + if (ret) + return ret; + + /* SDHI2 - needs CPLD mux setup */ + gpio_request(GPIO_GP_3_29, NULL); + gpio_direction_output(GPIO_GP_3_29, 1); /* VLDO4=3.3V */ + gpio_request(GPIO_GP_5_25, NULL); + gpio_direction_output(GPIO_GP_5_25, 1); /* power on */ + + ret = sh_sdhi_init(CONFIG_SYS_SH_SDHI2_BASE, 2, 0); +#endif + return ret; +} + + +int dram_init(void) +{ + gd->ram_size = CONFIG_SYS_SDRAM_SIZE; + + return 0; +} + +const struct rmobile_sysinfo sysinfo = { + CONFIG_RMOBILE_BOARD_STRING +}; + +static const struct sh_serial_platdata serial_platdata = { + .base = SCIFA0_BASE, + .type = PORT_SCIFA, + .clk = CONFIG_MP_CLK_FREQ, +}; + +U_BOOT_DEVICE(stout_serials) = { + .name = "serial_sh", + .platdata = &serial_platdata, +}; |