ARM: DRA7xx: Add CPSW support to DRA7xx EVM

Adding support for CPSW Ethernet support found in DRA7xx EVM

Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>

5 files changed, 185 insertions, 5 deletions

diff --git a/arch/arm/cpu/armv7/omap5/prcm-regs.c b/arch/arm/cpu/armv7/omap5/prcm-regs.c
index 9dfeff9..579818d 100644
--- a/arch/arm/cpu/armv7/omap5/prcm-regs.c
+++ b/arch/arm/cpu/armv7/omap5/prcm-regs.c
@@ -378,6 +378,10 @@ struct omap_sys_ctrl_regs const omap5_ctrl = {
 
 struct omap_sys_ctrl_regs const dra7xx_ctrl = {
 	.control_status				= 0x4A002134,
+	.control_core_mac_id_0_lo		= 0x4A002514,
+	.control_core_mac_id_0_hi		= 0x4A002518,
+	.control_core_mac_id_1_lo		= 0x4A00251C,
+	.control_core_mac_id_1_hi		= 0x4A002520,
 	.control_core_mmr_lock1			= 0x4A002540,
 	.control_core_mmr_lock2			= 0x4A002544,
 	.control_core_mmr_lock3			= 0x4A002548,
diff --git a/arch/arm/include/asm/arch-omap5/cpu.h b/arch/arm/include/asm/arch-omap5/cpu.h
index 3de5984..fb5a568 100644
--- a/arch/arm/include/asm/arch-omap5/cpu.h
+++ b/arch/arm/include/asm/arch-omap5/cpu.h
@@ -99,6 +99,8 @@ struct watchdog {
 #endif /* __ASSEMBLY__ */
 #endif /* __KERNEL_STRICT_NAMES */
 
+#define BIT(x)				(1 << (x))
+
 #define WD_UNLOCK1		0xAAAA
 #define WD_UNLOCK2		0x5555
 
@@ -158,4 +160,8 @@ struct watchdog {
 #define PRM_RSTST		(PRM_DEVICE_BASE + 0x4)
 #define PRM_RSTST_WARM_RESET_MASK	0x7FEA
 
+/* DRA7XX CPSW Config space */
+#define CPSW_BASE			0x48484000
+#define CPSW_MDIO_BASE			0x48485000
+
 #endif /* _CPU_H */
diff --git a/arch/arm/include/asm/arch-omap5/omap.h b/arch/arm/include/asm/arch-omap5/omap.h
index d08fcff..597c692 100644
--- a/arch/arm/include/asm/arch-omap5/omap.h
+++ b/arch/arm/include/asm/arch-omap5/omap.h
@@ -192,6 +192,27 @@ struct s32ktimer {
 #define OMAP5_ABB_LDOVBBMPU_MUX_CTRL_MASK	(0x1 << 10)
 #define OMAP5_ABB_LDOVBBMPU_VSET_OUT_MASK	(0x1f << 0)
 
+/* IO Delay module defines */
+#define CFG_IO_DELAY_BASE		0x4844A000
+#define CFG_IO_DELAY_LOCK		(CFG_IO_DELAY_BASE + 0x02C)
+
+/* CPSW IO Delay registers*/
+#define CFG_RGMII0_TXCTL		(CFG_IO_DELAY_BASE + 0x74C)
+#define CFG_RGMII0_TXD0			(CFG_IO_DELAY_BASE + 0x758)
+#define CFG_RGMII0_TXD1			(CFG_IO_DELAY_BASE + 0x764)
+#define CFG_RGMII0_TXD2			(CFG_IO_DELAY_BASE + 0x770)
+#define CFG_RGMII0_TXD3			(CFG_IO_DELAY_BASE + 0x77C)
+#define CFG_VIN2A_D13			(CFG_IO_DELAY_BASE + 0xA7C)
+#define CFG_VIN2A_D17			(CFG_IO_DELAY_BASE + 0xAAC)
+#define CFG_VIN2A_D16			(CFG_IO_DELAY_BASE + 0xAA0)
+#define CFG_VIN2A_D15			(CFG_IO_DELAY_BASE + 0xA94)
+#define CFG_VIN2A_D14			(CFG_IO_DELAY_BASE + 0xA88)
+
+#define CFG_IO_DELAY_UNLOCK_KEY		0x0000AAAA
+#define CFG_IO_DELAY_LOCK_KEY		0x0000AAAB
+#define CFG_IO_DELAY_ACCESS_PATTERN	0x00029000
+#define CFG_IO_DELAY_LOCK_MASK		0x400
+
 #ifndef __ASSEMBLY__
 struct srcomp_params {
 	s8 divide_factor;
@@ -208,5 +229,10 @@ struct ctrl_ioregs {
 	u32 ctrl_emif_sdram_config_ext;
 	u32 ctrl_ddr_ctrl_ext_0;
 };
+
+struct io_delay {
+	u32 addr;
+	u32 dly;
+};
 #endif /* __ASSEMBLY__ */
 #endif
diff --git a/arch/arm/include/asm/omap_common.h b/arch/arm/include/asm/omap_common.h
index 2c5bd1a..66f416f 100644
--- a/arch/arm/include/asm/omap_common.h
+++ b/arch/arm/include/asm/omap_common.h
@@ -348,6 +348,10 @@ struct prcm_regs {
 
 struct omap_sys_ctrl_regs {
 	u32 control_status;
+	u32 control_core_mac_id_0_lo;
+	u32 control_core_mac_id_0_hi;
+	u32 control_core_mac_id_1_lo;
+	u32 control_core_mac_id_1_hi;
 	u32 control_std_fuse_opp_vdd_mpu_2;
 	u32 control_core_mmr_lock1;
 	u32 control_core_mmr_lock2;
diff --git a/board/ti/dra7xx/evm.c b/board/ti/dra7xx/evm.c
index 8190e4b..9a114e2 100644
--- a/board/ti/dra7xx/evm.c
+++ b/board/ti/dra7xx/evm.c
@@ -23,12 +23,53 @@
 #include <asm/ehci-omap.h>
 #endif
 
+#ifdef CONFIG_DRIVER_TI_CPSW
+#include <cpsw.h>
+#endif
+
 DECLARE_GLOBAL_DATA_PTR;
 
 const struct omap_sysinfo sysinfo = {
 	"Board: DRA7xx\n"
 };
 
+/*
+ * Adjust I/O delays on the Tx control and data lines of each MAC port. This
+ * is a workaround in order to work properly with the DP83865 PHYs on the EVM.
+ * In 3COM RGMII mode this PHY applies it's own internal clock delay, so we
+ * essentially need to counteract the DRA7xx internal delay, and we do this
+ * by delaying the control and data lines. If not using this PHY, you probably
+ * don't need to do this stuff!
+ */
+static void dra7xx_adj_io_delay(const struct io_delay *io_dly)
+{
+	int i = 0;
+	u32 reg_val;
+	u32 delta;
+	u32 coarse;
+	u32 fine;
+
+	writel(CFG_IO_DELAY_UNLOCK_KEY, CFG_IO_DELAY_LOCK);
+
+	while(io_dly[i].addr) {
+		writel(CFG_IO_DELAY_ACCESS_PATTERN & ~CFG_IO_DELAY_LOCK_MASK,
+		       io_dly[i].addr);
+		delta = io_dly[i].dly;
+		reg_val = readl(io_dly[i].addr) & 0x3ff;
+		coarse = ((reg_val >> 5) & 0x1F) + ((delta >> 5) & 0x1F);
+		coarse = (coarse > 0x1F) ? (0x1F) : (coarse);
+		fine = (reg_val & 0x1F) + (delta & 0x1F);
+		fine = (fine > 0x1F) ? (0x1F) : (fine);
+		reg_val = CFG_IO_DELAY_ACCESS_PATTERN |
+				CFG_IO_DELAY_LOCK_MASK |
+				((coarse << 5) | (fine));
+		writel(reg_val, io_dly[i].addr);
+		i++;
+	}
+
+	writel(CFG_IO_DELAY_LOCK_KEY, CFG_IO_DELAY_LOCK);
+}
+
 /**
  * @brief board_init
  *
@@ -42,11 +83,6 @@ int board_init(void)
 	return 0;
 }
 
-int board_eth_init(bd_t *bis)
-{
-	return 0;
-}
-
 /**
  * @brief misc_init_r - Configure EVM board specific configurations
  * such as power configurations, ethernet initialization as phase2 of
@@ -85,3 +121,107 @@ int board_mmc_init(bd_t *bis)
 	return 0;
 }
 #endif
+
+#ifdef CONFIG_DRIVER_TI_CPSW
+
+/* Delay value to add to calibrated value */
+#define RGMII0_TXCTL_DLY_VAL		((0x3 << 5) + 0x8)
+#define RGMII0_TXD0_DLY_VAL		((0x3 << 5) + 0x8)
+#define RGMII0_TXD1_DLY_VAL		((0x3 << 5) + 0x2)
+#define RGMII0_TXD2_DLY_VAL		((0x4 << 5) + 0x0)
+#define RGMII0_TXD3_DLY_VAL		((0x4 << 5) + 0x0)
+#define VIN2A_D13_DLY_VAL		((0x3 << 5) + 0x8)
+#define VIN2A_D17_DLY_VAL		((0x3 << 5) + 0x8)
+#define VIN2A_D16_DLY_VAL		((0x3 << 5) + 0x2)
+#define VIN2A_D15_DLY_VAL		((0x4 << 5) + 0x0)
+#define VIN2A_D14_DLY_VAL		((0x4 << 5) + 0x0)
+
+static void cpsw_control(int enabled)
+{
+	/* VTP can be added here */
+
+	return;
+}
+
+static struct cpsw_slave_data cpsw_slaves[] = {
+	{
+		.slave_reg_ofs	= 0x208,
+		.sliver_reg_ofs	= 0xd80,
+		.phy_id		= 0,
+	},
+	{
+		.slave_reg_ofs	= 0x308,
+		.sliver_reg_ofs	= 0xdc0,
+		.phy_id		= 1,
+	},
+};
+
+static struct cpsw_platform_data cpsw_data = {
+	.mdio_base		= CPSW_MDIO_BASE,
+	.cpsw_base		= CPSW_BASE,
+	.mdio_div		= 0xff,
+	.channels		= 8,
+	.cpdma_reg_ofs		= 0x800,
+	.slaves			= 1,
+	.slave_data		= cpsw_slaves,
+	.ale_reg_ofs		= 0xd00,
+	.ale_entries		= 1024,
+	.host_port_reg_ofs	= 0x108,
+	.hw_stats_reg_ofs	= 0x900,
+	.bd_ram_ofs		= 0x2000,
+	.mac_control		= (1 << 5),
+	.control		= cpsw_control,
+	.host_port_num		= 0,
+	.version		= CPSW_CTRL_VERSION_2,
+};
+
+int board_eth_init(bd_t *bis)
+{
+	int ret;
+	uint8_t mac_addr[6];
+	uint32_t mac_hi, mac_lo;
+	uint32_t ctrl_val;
+	const struct io_delay io_dly[] = {
+		{CFG_RGMII0_TXCTL, RGMII0_TXCTL_DLY_VAL},
+		{CFG_RGMII0_TXD0, RGMII0_TXD0_DLY_VAL},
+		{CFG_RGMII0_TXD1, RGMII0_TXD1_DLY_VAL},
+		{CFG_RGMII0_TXD2, RGMII0_TXD2_DLY_VAL},
+		{CFG_RGMII0_TXD3, RGMII0_TXD3_DLY_VAL},
+		{CFG_VIN2A_D13, VIN2A_D13_DLY_VAL},
+		{CFG_VIN2A_D17, VIN2A_D17_DLY_VAL},
+		{CFG_VIN2A_D16, VIN2A_D16_DLY_VAL},
+		{CFG_VIN2A_D15, VIN2A_D15_DLY_VAL},
+		{CFG_VIN2A_D14, VIN2A_D14_DLY_VAL},
+		{0}
+	};
+
+	/* Adjust IO delay for RGMII tx path */
+	dra7xx_adj_io_delay(io_dly);
+
+	/* try reading mac address from efuse */
+	mac_lo = readl((*ctrl)->control_core_mac_id_0_lo);
+	mac_hi = readl((*ctrl)->control_core_mac_id_0_hi);
+	mac_addr[0] = mac_hi & 0xFF;
+	mac_addr[1] = (mac_hi & 0xFF00) >> 8;
+	mac_addr[2] = (mac_hi & 0xFF0000) >> 16;
+	mac_addr[3] = mac_lo & 0xFF;
+	mac_addr[4] = (mac_lo & 0xFF00) >> 8;
+	mac_addr[5] = (mac_lo & 0xFF0000) >> 16;
+
+	if (!getenv("ethaddr")) {
+		printf("<ethaddr> not set. Validating first E-fuse MAC\n");
+
+		if (is_valid_ether_addr(mac_addr))
+			eth_setenv_enetaddr("ethaddr", mac_addr);
+	}
+	ctrl_val = readl((*ctrl)->control_core_control_io1) & (~0x33);
+	ctrl_val |= 0x22;
+	writel(ctrl_val, (*ctrl)->control_core_control_io1);
+
+	ret = cpsw_register(&cpsw_data);
+	if (ret < 0)
+		printf("Error %d registering CPSW switch\n", ret);
+
+	return ret;
+}
+#endif