ARM: dts: sync meson-gxbb-nanopi-k2 from Linux 4.17

Get the meson-gxbb-nanopi-k2.dts file from Linux 4.17.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>

2 files changed, 324 insertions, 0 deletions

diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index 094c41b..f860588 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -53,6 +53,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += \
 	rk3399-puma-ddr1866.dtb \
 	rv1108-evb.dtb
 dtb-$(CONFIG_ARCH_MESON) += \
+	meson-gxbb-nanopi-k2.dtb \
 	meson-gxbb-odroidc2.dtb \
 	meson-gxl-s905x-p212.dtb \
 	meson-gxl-s905x-libretech-cc.dtb \
diff --git a/arch/arm/dts/meson-gxbb-nanopi-k2.dts b/arch/arm/dts/meson-gxbb-nanopi-k2.dts
new file mode 100644
index 0000000..7d5709c
--- /dev/null
+++ b/arch/arm/dts/meson-gxbb-nanopi-k2.dts
@@ -0,0 +1,323 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2017 Andreas Färber
+ */
+
+/dts-v1/;
+
+#include "meson-gxbb.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	compatible = "friendlyarm,nanopi-k2", "amlogic,meson-gxbb";
+
+	aliases {
+		serial0 = &uart_AO;
+		ethernet0 = &ethmac;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x0 0x0 0x80000000>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		stat {
+			label = "nanopi-k2:blue:stat";
+			gpios = <&gpio_ao GPIOAO_13 GPIO_ACTIVE_HIGH>;
+			default-state = "on";
+			panic-indicator;
+		};
+	};
+
+	vdd_5v: regulator-vdd-5v {
+		compatible = "regulator-fixed";
+		regulator-name = "VDD_5V";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
+
+	vddio_ao18: regulator-vddio-ao18 {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDIO_AO18";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+	};
+
+	vddio_ao3v3: regulator-vddio-ao3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDIO_AO3.3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	vddio_tf: regulator-vddio-tf {
+		compatible = "regulator-gpio";
+
+		regulator-name = "VDDIO_TF";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpios = <&gpio_ao GPIOAO_2 GPIO_ACTIVE_HIGH>;
+		gpios-states = <0>;
+
+		states = <3300000 0>,
+		         <1800000 1>;
+
+		regulator-settling-time-up-us = <100>;
+		regulator-settling-time-down-us = <5000>;
+	};
+
+	wifi_32k: wifi-32k {
+		compatible = "pwm-clock";
+		#clock-cells = <0>;
+		clock-frequency = <32768>;
+		pwms = <&pwm_ef 0 30518 0>; /* PWM_E at 32.768KHz */
+	};
+
+	sdio_pwrseq: sdio-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&gpio GPIOX_6 GPIO_ACTIVE_LOW>;
+		clocks = <&wifi_32k>;
+		clock-names = "ext_clock";
+	};
+
+	vcc1v8: regulator-vcc1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "VCC1.8V";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+	};
+
+	vcc3v3: regulator-vcc3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "VCC3.3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	emmc_pwrseq: emmc-pwrseq {
+		compatible = "mmc-pwrseq-emmc";
+		reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>;
+	};
+};
+
+&ethmac {
+	status = "okay";
+	pinctrl-0 = <&eth_rgmii_pins>;
+	pinctrl-names = "default";
+
+	phy-handle = <&eth_phy0>;
+	phy-mode = "rgmii";
+
+	amlogic,tx-delay-ns = <2>;
+
+	snps,reset-gpio = <&gpio GPIOZ_14 0>;
+	snps,reset-delays-us = <0 10000 1000000>;
+	snps,reset-active-low;
+
+	mdio {
+		compatible = "snps,dwmac-mdio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		eth_phy0: ethernet-phy@0 {
+			/* Realtek RTL8211F (0x001cc916) */
+			reg = <0>;
+			interrupt-parent = <&gpio_intc>;
+			/* MAC_INTR on GPIOZ_15 */
+			interrupts = <29 IRQ_TYPE_LEVEL_LOW>;
+		};
+	};
+};
+
+&ir {
+	status = "okay";
+	pinctrl-0 = <&remote_input_ao_pins>;
+	pinctrl-names = "default";
+};
+
+&pinctrl_aobus {
+	gpio-line-names = "UART TX", "UART RX", "Power Control", "Power Key In",
+			  "VCCK En", "CON1 Header Pin31",
+			  "I2S Header Pin6", "IR In", "I2S Header Pin7",
+			  "I2S Header Pin3", "I2S Header Pin4",
+			  "I2S Header Pin5", "HDMI CEC", "SYS LED",
+			  /* GPIO_TEST_N */
+			  "";
+};
+
+&pinctrl_periphs {
+	gpio-line-names = /* Bank GPIOZ */
+			  "Eth MDIO", "Eth MDC", "Eth RGMII RX Clk",
+			  "Eth RX DV", "Eth RX D0", "Eth RX D1", "Eth RX D2",
+			  "Eth RX D3", "Eth RGMII TX Clk", "Eth TX En",
+			  "Eth TX D0", "Eth TX D1", "Eth TX D2", "Eth TX D3",
+			  "Eth PHY nRESET", "Eth PHY Intc",
+			  /* Bank GPIOH */
+			  "HDMI HPD", "HDMI DDC SDA", "HDMI DDC SCL",
+			  "CON1 Header Pin33",
+			  /* Bank BOOT */
+			  "eMMC D0", "eMMC D1", "eMMC D2", "eMMC D3", "eMMC D4",
+			  "eMMC D5", "eMMC D6", "eMMC D7", "eMMC Clk",
+			  "eMMC Reset", "eMMC CMD",
+			  "", "", "", "", "eMMC DS",
+			  "", "",
+			  /* Bank CARD */
+			  "SDCard D1", "SDCard D0", "SDCard CLK", "SDCard CMD",
+			  "SDCard D3", "SDCard D2", "SDCard Det",
+			  /* Bank GPIODV */
+			  "", "", "", "", "", "", "", "", "", "", "", "", "",
+			  "", "", "", "", "", "", "", "", "", "", "",
+			  "I2C A SDA", "I2C A SCK", "I2C B SDA", "I2C B SCK",
+			  "VDDEE Regulator", "VCCK Regulator",
+			  /* Bank GPIOY */
+			  "CON1 Header Pin7", "CON1 Header Pin11",
+			  "CON1 Header Pin13", "CON1 Header Pin15",
+			  "CON1 Header Pin18", "CON1 Header Pin19",
+			  "CON1 Header Pin22", "CON1 Header Pin21",
+			  "CON1 Header Pin24", "CON1 Header Pin23",
+			  "CON1 Header Pin26", "CON1 Header Pin29",
+			  "CON1 Header Pin32", "CON1 Header Pin8",
+			  "CON1 Header Pin10", "CON1 Header Pin16",
+			  "CON1 Header Pin12",
+			  /* Bank GPIOX */
+			  "WIFI SDIO D0", "WIFI SDIO D1", "WIFI SDIO D2",
+			  "WIFI SDIO D3", "WIFI SDIO CLK", "WIFI SDIO CMD",
+			  "WIFI Power Enable", "WIFI WAKE HOST",
+			  "Bluetooth PCM DOUT", "Bluetooth PCM DIN",
+			  "Bluetooth PCM SYNC", "Bluetooth PCM CLK",
+			  "Bluetooth UART TX", "Bluetooth UART RX",
+			  "Bluetooth UART CTS", "Bluetooth UART RTS",
+			  "", "", "", "WIFI 32K", "Bluetooth Enable",
+			  "Bluetooth WAKE HOST", "",
+			  /* Bank GPIOCLK */
+			  "", "CON1 Header Pin35", "", "";
+};
+
+&pwm_ef {
+	status = "okay";
+	pinctrl-0 = <&pwm_e_pins>;
+	pinctrl-names = "default";
+	clocks = <&clkc CLKID_FCLK_DIV4>;
+	clock-names = "clkin0";
+};
+
+&saradc {
+	status = "okay";
+	vref-supply = <&vddio_ao18>;
+};
+
+/* SDIO */
+&sd_emmc_a {
+	status = "okay";
+	pinctrl-0 = <&sdio_pins>, <&sdio_irq_pins>;
+	pinctrl-1 = <&sdio_clk_gate_pins>;
+	pinctrl-names = "default", "clk-gate";
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	bus-width = <4>;
+	cap-sd-highspeed;
+	max-frequency = <200000000>;
+
+	non-removable;
+	disable-wp;
+
+	mmc-pwrseq = <&sdio_pwrseq>;
+
+	vmmc-supply = <&vddio_ao3v3>;
+	vqmmc-supply = <&vddio_ao18>;
+
+	brcmf: wifi@1 {
+		compatible = "brcm,bcm4329-fmac";
+		reg = <1>;
+	};
+};
+
+/* SD */
+&sd_emmc_b {
+	status = "okay";
+	pinctrl-0 = <&sdcard_pins>;
+	pinctrl-1 = <&sdcard_clk_gate_pins>;
+	pinctrl-names = "default", "clk-gate";
+
+	bus-width = <4>;
+	cap-sd-highspeed;
+	sd-uhs-sdr12;
+	sd-uhs-sdr25;
+	sd-uhs-sdr50;
+	sd-uhs-sdr104;
+	max-frequency = <200000000>;
+	disable-wp;
+
+	cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_HIGH>;
+	cd-inverted;
+
+	vmmc-supply = <&vddio_ao3v3>;
+	vqmmc-supply = <&vddio_tf>;
+};
+
+/* eMMC */
+&sd_emmc_c {
+	status = "disabled";
+	pinctrl-0 = <&emmc_pins>, <&emmc_ds_pins>;
+	pinctrl-1 = <&emmc_clk_gate_pins>;
+	pinctrl-names = "default", "clk-gate";
+
+	bus-width = <8>;
+	max-frequency = <200000000>;
+	non-removable;
+	disable-wp;
+	cap-mmc-highspeed;
+	mmc-ddr-1_8v;
+	mmc-hs200-1_8v;
+
+	mmc-pwrseq = <&emmc_pwrseq>;
+	vmmc-supply = <&vcc3v3>;
+	vqmmc-supply = <&vcc1v8>;
+};
+
+/* DBG_UART */
+&uart_AO {
+	status = "okay";
+	pinctrl-0 = <&uart_ao_a_pins>;
+	pinctrl-names = "default";
+};
+
+/* Bluetooth on AP6212 */
+&uart_A {
+	status = "disabled";
+	pinctrl-0 = <&uart_a_pins>, <&uart_a_cts_rts_pins>;
+	pinctrl-names = "default";
+};
+
+/* 40-pin CON1 */
+&uart_C {
+	status = "disabled";
+	pinctrl-0 = <&uart_c_pins>;
+	pinctrl-names = "default";
+};
+
+&usb0_phy {
+	status = "okay";
+	phy-supply = <&vdd_5v>;
+};
+
+&usb1_phy {
+	status = "okay";
+};
+
+&usb0 {
+	status = "okay";
+};
+
+&usb1 {
+	status = "okay";
+};