Add a new phy_ops *release* invoked when the consumer relinquishes the
PHY using phy_put/devm_phy_put. The initializations done by the PHY
driver in of_xlate call back can be can be cleaned up here.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

Use devm_clk_get_optional() to get optional clock

Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

Use devm_clk_get_optional() to get optional clock

Cc: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Reviewed-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

Use devm_clk_get_optional() to get optional clock

Cc: Andy Gross <andy.gross@linaro.org>
Cc: David Brown <david.brown@linaro.org>
Cc: Vivek Gautam <vivek.gautam@codeaurora.org>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

Use devm_clk_get_optional() to get optional clock

Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

Since the previous code enabled/disabled the irqs both OHCI and EHCI,
it is possible to cause unexpected interruptions. To avoid this,
this patch creates multiple phy instances from phandle and
enables/disables independent irqs by the instances.

Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Tested-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

To implement multiple phy instances in the future, this patch uses
pdev's device pointer on dev_vdbg() instead of the phy's device
pointer.

Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

To have the detailed property on each PHY specifier, this patch revises
the #phy-cells property.

Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

This patch adds support for r8a77470 (RZ/G1C). We can reuse this driver for
initializing timing/interrupt generation registers.

Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

This patch adds support for RZ/G1C (r8a77470) SoC. RZ/G1C SoC has a
PLL register shared between hsusb0 and hsusb1. Compared to other RZ/G1
and R-Car Gen2/3, USB Host needs to deassert the pll reset.

Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-and-Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

Document RZ/G1C (R8A77470) SoC bindings.

For RZ/G1C, this driver is used to enable interrupt generation and
initializing timing registers which is part of phy_init code.

Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

Add USB PHY support for r8a77470 SoC. Renesas RZ/G1C (R8A77470)
USB PHY is similar to the R-Car Gen2 family, but has the below
feature compared to other RZ/G1 and R-Car Gen2/3 SoCs

It has a shared pll reset for usbphy0/usbphy1 and this register
reside in usbphy0 block.

Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

TRM [1] mentions that we need to power up
PCIESS_PHY_TX and PCIESS_PHY_RX before configuring
PCIe_PHY_RX SCP settings.

See "Table 26-81. PCIePHY Subsystem Low-Level Programming Sequence".

[1] DRA75x, DRA74x TRM - http://www.ti.com/lit/ug/sprui30f/sprui30f.pdf



Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

As per "Table 26-7. SATA PHY Subsystem Low-Level Programming Sequence"
in TRM [1] we need to turn on SATA_PHY_TX before SATA_PHY_RX.

[1] DRA75x, DRA74x TRM - http://www.ti.com/lit/ug/sprui30f/sprui30f.pdf



Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

For increased DPLL stability use the settings recommended in
the TRM [1] for PHY_RX registers for SATA and USB.

For SATA we need to use spread spectrum settings even
though we don't have spread spectrum enabled. The
suggested non-spread spectrum settings don't work.

[1] DRA75x, DRA74x TRM - http://www.ti.com/lit/ug/sprui30f/sprui30f.pdf



Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

Introduce a mode property in the driver data so that
we don't have to keep using "of_device_is_compatible()"
throughtout the driver.

No functional change.

Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

There seems to be a missing bit-wise or operator when setting val,
fix this by adding it in.

Fixes: 2796ceb0

 ("phy: ti-pipe3: Update pcie phy settings")
Cc: stable@vger.kernel.org # v4.19+
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

Add UFS M-PHY driver on MediaTek chipsets.

Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Reviewed-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

Add UFS M-PHY node document for MediaTek SoC chips.

Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

This patch documents the new proprty drive-impedance-ohm for
Rockchip's eMMC PHY node.

Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

The rockchip-emmc PHY can be configured with different
drive impedance values. Currenlty a value of 50 Ohm is
hard coded into the driver.

This patch introduces the DTS property 'drive-impedance-ohm'
for the rockchip-emmc phy node, which uses the value from the DTS
to setup the drive impedance accordingly.

Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

The phy code was using implicit sequencing between the PHY driver
and the UFS driver to implement certain hardware requirements.
Specifically, the PHY reset register in the UFS controller needs
to be deasserted before serdes start occurs in the PHY.

Before this change, the code was doing this by utilizing the two
phy callbacks, phy_init() and phy_poweron(), as "init step 1" and
"init step 2", where the UFS driver would deassert reset between
these two steps.

This makes it challenging to power off the regulators in suspend,
as regulators are initialized in init, not in poweron(), but only
poweroff() is called during suspend, not exit().

For UFS, move the actual firing up of the PHY to phy_poweron() and
phy_poweroff() callbacks, rather than init()/exit(). UFS calls
phy_poweroff() during suspend, so now all clocks and regulators for
the phy can be powered down during suspend.

QMP is a little tricky because the PHY is also shared with PCIe and
USB3, which have their own definitions for init() and poweron(). Rename
the meaty functions to _enable() and _disable() to disentangle from the
PHY core names, and then create two different ops structures: one for
UFS and one for the other PHY types.

In phy-qcom-ufs, remove the 'is_powered_on' and 'is_started' guards,
as the generic PHY code does the reference counting. The
14/20nm-specific init functions get collapsed into the generic power_on()
function, with the addition of a calibrate() callback specific to 14/20nm.

Signed-off-by: Evan Green <evgreen@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

Move the PHY reset from ufs-qcom into the respective PHYs. This will
allow us to merge the two phases of UFS PHY initialization.

Signed-off-by: Evan Green <evgreen@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

Expose a reset controller that the phy will later use to control its
own PHY reset in the UFS controller. This will enable the combining
of PHY init functionality into a single function.

Signed-off-by: Evan Green <evgreen@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

Add a resets property to the PHY that represents the PHY reset
register in the UFS controller itself. This better describes the
complete specification of the PHY, and allows the PHY to perform
its initialization in a single function, rather than relying on
back-channel sequencing of initialization through the PHY framework.

Signed-off-by: Evan Green <evgreen@chromium.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

Add a required reset to the SDM845 UFS phy to express the PHY reset
bit inside the UFS controller register space. Before this change, this
reset was not expressed in the DT, and the driver utilized two different
callbacks (phy_init and phy_poweron) to implement a two-phase
initialization procedure that involved deasserting this reset between
init and poweron. This abused the two callbacks and diluted their
purpose.

That scheme does not work as regulators cannot be turned off in
phy_poweroff because they were turned on in init, rather than poweron.
The net result is that regulators are left on in suspend that shouldn't
be.

This new scheme gives the UFS reset to the PHY, so that it can fully
initialize itself in a single callback. We can then turn regulators on
during poweron and off during poweroff.

Signed-off-by: Evan Green <evgreen@chromium.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

Enable Qualcomm UFS controllers to expose the PHY reset via a reset
controller.

Signed-off-by: Evan Green <evgreen@chromium.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

This adds support for the shared USB3 + PCIE PHY found in the
Amlogic G12A SoC Family.

It supports USB3 Host mode or PCIE 2.0 mode, depending on the layout of
the board.

Selection is done by the #phy-cells, making the mode static and exclusive.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

This adds support for the USB2 PHY found in the Amlogic G12A SoC Family.

It supports Host and/or Peripheral mode, depending on it's position.
The first PHY is only used as Host, but the second supports Dual modes
defined by the USB Control Glue HW in front of the USB Controllers.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

Add the Amlogic G12A Family USB3 + PCIE Combo PHY Bindings.

This PHY can provide exclusively USB3 or PCIE support on shared I/Os.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

Add the Amlogic G12A Family USB2 OTG PHY Bindings

The PHY can work in host or peripheral modes depending on it's position.
Configuration of the mode is part of the USBCTRL registers which are
outside of the PHY registers.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

USB PHY driver supports two types of stingray USB PHYs
 - Type 1 is a combo PHY contains two PHYs, one SS and one HS.
 - Type 2 is a single HS PHY.

These two PHY versons support both Generic xHCI host controller driver
and BDC Broadcom device controller driver.

Signed-off-by: Srinath Mannam <srinath.mannam@broadcom.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

Add DT binding document for Stingray USB PHY.

Signed-off-by: Srinath Mannam <srinath.mannam@broadcom.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

Add support for the XUSB pad controller found on Tegra186 SoCs. It is
mostly similar to the same IP found on earlier chips, but the number of
pads exposed differs, as do the programming sequences.

Note that the DVDD_PEX, DVDD_PEX_PLL, HVDD_PEX and HVDD_PEX_PLL power
supplies of the XUSB pad controller require strict power sequencing and
are therefore controlled by the PMIC on Tegra186.

Signed-off-by: JC Kuo <jckuo@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
[dan.carpenter@oracle.com: Fix testing the wrong variable in probe()]
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
[yuehaibing@huawei.com: Make two functions static to fix sparse warning]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

Support enabling various supplies needed to provide power to the PLLs
and logic used to drive the USB, PCI and SATA pads.

Reviewed-by: JC Kuo <jckuo@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

The device tree bindings document the "mode" property of "ports"
subnodes, but the driver was not parsing the property. In preparation
for adding role switching, parse the property at probe time.

Based on work by JC Kuo <jckuo@nvidia.com>.

Reviewed-by: JC Kuo <jckuo@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

Tegra186 USB2 pads and USB3 pads do not have hardware mux for changing
the pad function. For such "lanes", we can skip the lane mux register
programming.

Signed-off-by: JC Kuo <jckuo@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

Extend the bindings to cover the set of features found in Tegra186. Note
that, technically, there are four more supplies connected to the XUSB
pad controller (DVDD_PEX, DVDD_PEX_PLL, HVDD_PEX and HVDD_PEX_PLL), but
the power sequencing requirements of Tegra186 require these to be under
the control of the PMIC.

Reviewed-by: JC Kuo <jckuo@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

Pull more Kbuild updates from Masahiro Yamada:

 - add more Build-Depends to Debian source package

 - prefix header search paths with $(srctree)/

 - make modpost show verbose section mismatch warnings

 - avoid hard-coded CROSS_COMPILE for h8300

 - fix regression for Debian make-kpkg command

 - add semantic patch to detect missing put_device()

 - fix some warnings of 'make deb-pkg'

 - optimize NOSTDINC_FLAGS evaluation

 - add warnings about redundant generic-y

 - clean up Makefiles and scripts

* tag 'kbuild-v5.1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
  kconfig: remove stale lxdialog/.gitignore
  kbuild: force all architectures except um to include mandatory-y
  kbuild: warn redundant generic-y
  Revert "modsign: Abort modules_install when signing fails"
  kbuild: Make NOSTDINC_FLAGS a simply expanded variable
  kbuild: deb-pkg: avoid implicit effects
  coccinelle:...