- Jan 06, 2022
-
-
Shengjiu Wang authored
Transfer the refined slots and slot_width to akcodec_get_mclk_rate() for mclk calculation, otherwise the mclk frequency does not match with the slots and slot_width for S16_LE format, because the default slot_width is 32. Fixes: aa736700 ("ASoC: imx-card: Add imx-card machine driver") Signed-off-by:
Shengjiu Wang <shengjiu.wang@nxp.com> Link: https://lore.kernel.org/r/1641292835-19085-3-git-send-email-shengjiu.wang@nxp.com Signed-off-by:
Mark Brown <broonie@kernel.org>
-
Shengjiu Wang authored
The SAI on i.MX8MQ don't support one2one ratio for mclk:bclk, so the mclk frequency exceeds the supported range of codec for the case that sample rate is larger than 705kHZ and format is S32_LE. Update the supported width for such case. Fixes: aa736700 ("ASoC: imx-card: Add imx-card machine driver") Signed-off-by:
-
Takashi Iwai authored
A randconfig caught a compile warning that is now treated as a fatal error: sound/soc/codecs/ak4375.c:415:13: error: ‘ak4375_power_off’ defined but not used [-Werror=unused-function] where ak4375_power_off() is used only from the PM handler. As both suspend and resumes are already marked with __maybe_unused, let's rip off the superfluous ifdef CONFIG_PM, so that the error above can be avoided. Fixes: 53778b82 ("ASoC: Add AK4375 support") Signed-off-by:
Takashi Iwai <tiwai@suse.de> Link: https://lore.kernel.org/r/20220105162409.20635-1-tiwai@suse.de Signed-off-by:
-
- Jan 05, 2022
-
-
Mark Brown authored
Merge series from Charles Keepax <ckeepax@opensource.cirrus.com>: This patch series adds support for the low power hibernation feature on cs35l41. This allows the DSP memory to be retained whilst the device enters a very low power state.
-
Fabio Estevam authored
When the reset_gpio GPIO is used, it is better to put the codec back into reset state when the driver unbinds. Add a remove() function to accomplish that. Suggested-by:
Charles Keepax <ckeepax@opensource.cirrus.com> Signed-off-by:
Fabio Estevam <festevam@denx.de> Acked-by:
-
Charles Keepax authored
In the case a device can support retaining the firmware memory across low power states it is useful for the preloader widget to only power up whilst actually loading/unloading the core, as opposed to the normal operation where the widget is powered for the entire time a firmware is preloaded onto the core. Add support for this mode and a flag to enable it. Signed-off-by:
-
Charles Keepax authored
If the Halo registers are kept in the register cache the HALO_CORE_RESET bit will be retained as 1 after reset is triggered in cs_dsp_halo_start_core. This will cause subsequent writes to reset the core which is not desired. Apart from this bit the rest of the register bits are cacheable, so for safety sake clear the bit to ensure the cache is consistent. Signed-off-by:
-
Charles Keepax authored
It makes no sense to cache the test/user key registers, since they require values written at specific times, mark them volatile. It is probably best if they can't be accessed from user-space either, so mark them precious as well. The interrupt force, edge, polarity and debounce are all settings applied to the IRQ rather than status bits and as such should not be volatile. The OTP trim values will require re-application in the event of a cache sync and as such should not be volatile. The OTPID however should be volatile. The DSP scratch registers are used to read back an error/debug code from the DSP on shutdown, as such these should be marked volatile. Finally, add some missing defaults, add TST_FS_MON0, and allow the DSP core control register to be cached. Signed-off-by:
-
Charles Keepax authored
The wm_adsp_event should be called before the early_event on power down, event stops the core running and early_event then powers down the core. Additionally, the core should only be stopped if it was actually running in the first place. Signed-off-by:
-
Charles Keepax authored
The IRQ is not used for the PDN_DONE bit, this is polled during the DAPM sequence, remove the misleading comment. Signed-off-by:
-
David Rhodes authored
Add IDs for the CS35L51/53 variants, the functionality is shared with CS35L41. Signed-off-by:
David Rhodes <david.rhodes@cirrus.com> Signed-off-by:
-
- Jan 04, 2022
-
-
Alyssa Ross authored
modprobe can't handle spaces in aliases. Fixes: 9e28f653 ("ASoC: fsl_mqs: Add MQS component driver") Signed-off-by:
Alyssa Ross <hi@alyssa.is> Link: https://lore.kernel.org/r/20220104132218.1690103-1-hi@alyssa.is Signed-off-by:
-
- Dec 31, 2021
-
-
Mark Brown authored
Merge series from Trevor Wu <trevor.wu@mediatek.com>: This series of patches repairs some problems for pcmif BE dai. The unexpected control flow is corrected, and the missing playback support of DPCM is added.
-
Mark Brown authored
Merge series from Lucas Tanure <tanureal@opensource.cirrus.com>: Initial refactoring to support use of cs35l41 from the HDA driver stack.
-
Mark Brown authored
So we can send to Linus.
-
Lucas Tanure authored
ASoC and HDA will use the same registers to configure internal boost for the device Signed-off-by:
Lucas Tanure <tanureal@opensource.cirrus.com> Link: https://lore.kernel.org/r/20211217115708.882525-7-tanureal@opensource.cirrus.com Signed-off-by:
-
Lucas Tanure authored
ASoC and HDA will use the same register to set channels for the device Signed-off-by:
-
Lucas Tanure authored
ASoC and HDA systems require the same errata patches, so move it to the shared code using a function the correctly applies the patches by revision Also, move CS35L41_DSP1_CCM_CORE_CTRL write to errata patch function as is required to be written at boot, but not in regmap_register_patch sequence as will affect waking up from hibernation Signed-off-by:
-
Lucas Tanure authored
ASoC and HDA systems for all revisions of CS35L41 will benefit from having this initialization, so add it to reg_sequence of each revision By moving to reg_sequence all gains are set to zero. And boost, monitoring parts, and class D amplifier are disabled. Signed-off-by:
-
Lucas Tanure authored
ASoC and HDA will do the same cs35l41_otp_unpack, so move it to shared code Signed-off-by:
-
Lucas Tanure authored
To support CS35L41 in HDA systems the HDA driver for CS35L41 would have to duplicate some functions that already exist on ASoC driver So instead of duplicate the code, use the new lib source as a shared resource for both ASoC and HDA Also, change the way CONFIG_SND_SOC_CS35L41 is selected, as reported by Intel Kernel test robot, it is possible to build SND_SOC_CS35L41_SPI/I2C without the main driver, which would lead to build failures. Signed-off-by:
kernel test robot <lkp@intel.com> Link: https://lore.kernel.org/r/20211217115708.882525-2-tanureal@opensource.cirrus.com Signed-off-by:
-
Trevor Wu authored
PCM1_BE should be a dai_link for both playback and capture. In the patch, the missing DPCM playback support is added. Signed-off-by:
Trevor Wu <trevor.wu@mediatek.com> Link: https://lore.kernel.org/r/20211230084731.31372-3-trevor.wu@mediatek.com Signed-off-by:
-
Trevor Wu authored
Originally, the conditions for preventing reentry are not correct. dai->component->active is not the state specifically for pcmif dai, so it is not a correct condition to indicate the status of pcmif dai. On the other hand, snd_soc_dai_stream_actvie() in prepare ops for both playback and capture possibly return true at the first entry when these two streams are opened at the same time. In the patch, I refer to the implementation in mt8192-dai-pcm.c. Clock and enabling bit for PCMIF are managed by DAPM, and the condition for prepare ops is replaced by the status of dai widget. Fixes: 1f95c019 ("ASoC: mediatek: mt8195: support pcm in platform driver") Signed-off-by:
-
- Dec 29, 2021
-
-
Derek Fang authored
The mclk might not be registered as a fixed clk name "mclk" on some platforms. In those platforms, if the mclk needed to be controlled by codec driver and acquired by a fixed name, it would be a problem. This patch to fix the issue that wclk becomes an orphan due to the fixed mclk's name. Signed-off-by:
Derek Fang <derek.fang@realtek.com> Link: https://lore.kernel.org/r/20211227055446.27563-1-derek.fang@realtek.com Signed-off-by:
-
Trevor Wu authored
Playback pop is observed and the root cause is the reference clock provided by MT8195 is diabled before RT5682 finishes the control flow. To ensure the reference clock supplied to RT5682 is disabled after RT5682 finishes all register controls. We replace BCLK with MCLK for RT5682 reference clock, and makes use of set_bias_level_post to handle MCLK which guarantees MCLK is off after all RT5682 register access. Signed-off-by:
Tzung-Bi Shih <tzungbi@google.com> Link: https://lore.kernel.org/r/20211228064821.27865-1-trevor.wu@mediatek.com Signed-off-by:
-
Jiasheng Jiang authored
Because of the potential failure of the ioremap(), the buf->area could be NULL. Therefore, we need to check it and return -ENOMEM in order to transfer the error. Fixes: f09aecd5 ("ASoC: SAMSUNG: Add I2S0 internal dma driver") Signed-off-by:
Jiasheng Jiang <jiasheng@iscas.ac.cn> Reviewed-by:
Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com> Link: https://lore.kernel.org/r/20211228034026.1659385-1-jiasheng@iscas.ac.cn Signed-off-by:
-
Tzung-Bi Shih authored
Uses of_device_get_match_data() helper to clean some boilerplate code. Signed-off-by:
-
Fabio Estevam authored
The Chip ID - Register 01h contains the following description as per the CS4265 datasheet: "Bits 7 through 4 are the part number ID, which is 1101b (0Dh)" The current error message is incorrect as it prints CS4265_CHIP_ID, which is the register number, instead of printing the expected part number ID value. To make it clearer, also do a shift by 4, so that the error message would become: [ 4.218083] cs4265 1-004f: CS4265 Part Number ID: 0x0 Expected: 0xd Signed-off-by:
-
- Dec 25, 2021
-
-
Mark Brown authored
Merge series from Bard Liao <yung-chuan.liao@linux.intel.com>: This series contains three topics. 1. SoundWire: Intel: remove pdm support 2. ASoC/SoundWire: dai: expand 'stream' concept beyond SoundWire 3. ASoC/SOF/SoundWire: fix suspend-resume on pause with dynamic pipelines The topics are independent but the changes are dependent. So please allow me to send them in one series.
-
- Dec 24, 2021
-
-
V sujith kumar Reddy authored
Configure the speaker gpio pin based on power sequence of the DAPM speaker events. Enable speaker after widget power up and Disable before widget powerdown. Signed-off-by:
V sujith kumar Reddy <vsujithkumar.reddy@amd.com> Link: https://lore.kernel.org/r/20211224150058.2444776-1-vsujithkumar.reddy@amd.com Signed-off-by:
-
chiminghao authored
return value form directly instead of taking this in another redundant variable. Reported-by:
Zeal Robot <zealci@zte.com.cm> Signed-off-by:
chiminghao <chi.minghao@zte.com.cn> Link: https://lore.kernel.org/r/20211209015707.409870-1-chi.minghao@zte.com.cn Signed-off-by:
-
Jiasheng Jiang authored
Yes, you are right and now the return code depending on the init_clks(). Fixes: 6078c651 ("soc: mediatek: Refine scpsys to support multiple platform") Signed-off-by:
-
Tzung-Bi Shih authored
Device nodes can be released after components have bound. Shortens the lifecycle of the device nodes. Releases the reference counts after snd_soc_register_card. Signed-off-by:
-
Tzung-Bi Shih authored
Eliminates error messages if snd_soc_register_card() failed. Kernel emits messages if device probe error anyway. Signed-off-by:
-
Tzung-Bi Shih authored
Fixes the device_node leak. Signed-off-by:
-
Tzung-Bi Shih authored
Fixes the device_node leak. Signed-off-by:
-
Pierre-Louis Bossart authored
While the hardware supports PDM streams, this capability has never been tested or enabled on any product, so this is dead-code. Let's remove all this. Signed-off-by:
Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Reviewed-by:
Péter Ujfalusi <peter.ujfalusi@linux.intel.com> Reviewed-by:
Rander Wang <rander.wang@intel.com> Signed-off-by:
Bard Liao <yung-chuan.liao@linux.intel.com> Acked-By:
Vinod Koul <vkoul@kernel.org> Link: https://lore.kernel.org/r/20211224021034.26635-8-yung-chuan.liao@linux.intel.com Signed-off-by:
-
Pierre-Louis Bossart authored
cppcheck warning: drivers/soundwire/intel.c:1487:10: style: Variable 'ret' is assigned a value that is never used. [unreadVariable] int ret = 0; ^ Signed-off-by: -
Pierre-Louis Bossart authored
Overloading the tx_mask with a linear value is asking for trouble and only works because the codec_dai hw_params() is called before the cpu_dai hw_params(). Move to the more generic set_stream() API to pass the hdac_stream information. Signed-off-by:
Ranjani Sridharan <ranjani.sridharan@intel.com> Signed-off-by:
-
Pierre-Louis Bossart authored
The HDAudio ASoC support relies on the set_tdm_slots() helper to store the HDaudio stream tag in the tx_mask. This only works because of the pre-existing order in soc-pcm.c, where the hw_params() is handled for codec_dais *before* cpu_dais. When the order is reversed, the stream_tag is used as a mask in the codec fixup functions: /* fixup params based on TDM slot masks */ if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK && codec_dai->tx_mask) soc_pcm_codec_params_fixup(&codec_params, codec_dai->tx_mask); As a result of this confusion, the codec_params_fixup() ends-up generating bad channel masks, depending on what stream_tag was allocated. We could add a flag to state that the tx_mask is really not a mask, but it would be quite ugly to persist in overloading concepts. Instead, this patch suggests a more generic get/set 'stream' API based on the existing model for SoundWire. We can expand the concept to store 'stream' opaque information that is specific to different DAI types. In the case of HDAudio DAIs, we only need to store a stream tag as an unsigned char pointer. The TDM rx_ and tx_masks should really only be used to store masks. Rename get_sdw_stream/set_sdw_stream callbacks and helpers as get_stream/set_stream. No functionality change beyond the rename. Signed-off-by:
-
