Platform support for lp5523 led chip

Signed-off-by: Ameya Palande <ameya.palande@nokia.com>
Signed-off-by: Mathias Nyman <mathias.nyman@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

0e433271

 "OMAP4: clock: Fix clock names and align with hwmod names"
renamed ducati_ick to ipu_fck.

Update OMAP4's iommu_device accordingly, so that omap_iommu_probe
doesn't break when calling clk_get.

Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>

iovmm is erroneously using sg_dma_len with unmapped (DMA API-wise)
SG entries, and will break if CONFIG_NEED_SG_DMA_LENGTH is enabled.

Fix that by using sg->length instead.

Reported-by: Russell King <linux@arm.linux.org.uk>
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>

Fix the pte programming to set the page attributes correctly
by replacing the bitwise check with an explicit values check.

Otherwise, 16MB entries will be erroneously programmed like
4KB entries, which is not what the hardware expects.

Signed-off-by: Suman Anna <s-anna@ti.com>
Acked-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>

Fix warning issued by gpio_set_value() call with TPS gpios.

Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Update authors and copyright, remove Free S/W Foundation postal address,
fix offsets of NAND partitions in comments.

Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Reset GPIO (OMAP_GPIO_152) for QUART in zoom2/zoom3 debug-board is
not requested at all. This would lead to problems if this GPIO is
wrongly requested. Hence request OMAP GPIO 152 for QUART RESET but
do not apply a reset pulse as it would reset QUART and
disturb the QUART settings.

Signed-off-by: Charulatha V <charu@ti.com>
Acked-by: Kevin Hilman <khilman@ti.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

overo_ads7846_init() is already called from overo_spi_init(), and
calling it twice is not only unnecessary but causes a warning as
"reg-fixed-voltage.1" is already added to the device tree.

Signed-off-by: Daniel Mack <zonque@gmail.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Use generic gpio call to check the validity of the gpio. Note that
this includes gpio 0 also which was missing before.

Signed-off-by: Silesh C V <silesh@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Currently autoidle is only enabled for OMAP2/3; by enabling autoidle,
the automatic L4 clock gating strategy is applied based on L4 activity,
otherwise L4 clock to module will be a free running.

Signed-off-by: Ambresh K <ambresh@ti.com>
[tony@atomide.com: updated for timer init changes]
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add missing call to clk_put.

A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/

)

// <smpl>
@r exists@
expression e1,e2;
statement S;
@@

e1 = clk_get@p1(...);
... when != e1 = e2
    when != clk_put(e1)
    when any
if (...) { ... when != clk_put(e1)
               when != if (...) { ... clk_put(e1) ... }
* return@p3 ...;
 } else S
// </smpl>

Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Merge branch 'for_3.1/pm-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-omap-pm into devel-cleanup

Conflicts:
	arch/arm/mach-omap2/pm-debug.c
	arch/arm/mach-omap2/pm.h

We haven't seen either use for in-driver transfer API in McBSP driver
over the years so it looks they can be removed too.

Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

We haven't seen any use for the SPI API in McBSP driver over the years. More
over, Peter Ujfalusi <peter.ujfalusi@ti.com> noticed that SPI mode is not
even supported since OMAP2430 so it's very unlikely that we'll see any use
for it in the future either.

Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Fix compilation error introduced with 786b01a8


(cleanup regulator supply definitions in mach-omap2).

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
[tony@atomide.com: updated comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>

omap_nand_platform_data fields 'options', 'gpio_irq', 'nand_setup' and
'dma_channel' are never referenced by the NAND driver, yet various
board files are initializing those fields. This is both incorrect and
confusing, so remove them. This allows to get rid of a global
variable in gpmc-nand.c.

This also corrects an issue where some boards are trying to pass NAND
16bit flag through .options, but the driver is using .devsize instead
and ignoring .options.

Finally, .dev_ready is treated as a flag by the driver, so make it bool
instead of a function pointer.

Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

We can keep everything sys_timer and gptimer.c related code in
timer.c as the code will be very minimal.

Later on we can also remove timer-mpu.c, as it can be called from
omap4_timer_init function.

This allows us to get rid of confusing existing files. We currently
have timer-gp.c, timer-mpu.c, and patches have been posted to add
dmtimer.c. There's no need to have these multiple files, we can
put everything into timer.c.

Signed-off-by: Tony Lindgren <tony@atomide.com>

This is no longer needed as we now just set the desired
.timer in MACHINE_START. We can now also remove timer-gp.h.

Signed-off-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>

Use dmtimer macros for clocksource. As with the clockevent,
this allows us to initialize the rest of dmtimer code later on.

Note that eventually we will be initializing the timesource
from init_early so sched_clock will work properly for
CONFIG_PRINTK_TIME.

Signed-off-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>

There's no need to initialize the dmtimer framework early.
Just mark the clocksource and timesource as reserved, and
initialize dmtimer with an arch_initcall.

Signed-off-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>

Fix the section mismatch warning:

  WARNING: vmlinux.o(.text+0x21118): Section mismatch
  in reference from the function pm_dbg_init() to the
  function .init.text:pwrdms_setup()
  The function pm_dbg_init() references
  the function __init pwrdms_setup().
  This is often because pm_dbg_init lacks a __init
  annotation or the annotation of pwrdms_setup is wrong.

Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>

Remove OMAP3-specific register dumping feature from PM debug layer.
This is removed because:

- it's ugly
- it's OMAP3-specific, and will obviously not scale to OMAP4+
- userspace /dev/mem-based tools (like omapconf) can do this much better

Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>

Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>

Remove the OMAP-specific PM debug 'sleep_while_idle' feature which is
currently available as an OMAP-specific debugfs entry.

This duplicates existing ARM-generic functionality available as a
boot-time option using the boot cmdline option 'hohlt'.

If runtime configuration of this is needed, then adding a debugfs
entry for the ARM-generic hlt/nohlt interface should be added.

Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>

Error label case seems to have a 2 tab indentation when just 1 is
necessary.

Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>

Since we already know the state of the autocomp enablement, we can
see if the requested state is different from the current state and
enable/disable SR only on the need basis.

Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>

We will enable and disable interrupt on a need basis in the class
driver. We need to keep the IRQ disabled by default else the
forceupdate or vcbypass events could trigger events that we don't
need/expect to handle.

This is a preparation for SmartReflex AVS class drivers such as
class 2 and class 1.5 which would need to use interrupts. Existing
SmartReflex AVS class 3 driver does not require to use interrupts
and is not impacted by this change.

Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>

Interrupt notification mechanism of SmartReflex can be used by the
choice of implementation of the class driver. For example, Class 2 and
Class 1.5 of SmartReflex can both use the interrupt notification to
identify the transition of voltage or other events.

Hence, the actual class does not matter for notifier. Let the class
driver's handling decide how it should be used. SmartReflex driver
should provide just the primitives.

Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>

This removes the support for setting the wake-up timer for debugging.

Later on we can reserve gptimer1 for PM code only and have similar
functionality.

Signed-off-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>

This patch makes timer-gp.c to use only a subset of dmtimer
functions without the need to initialize dmtimer code early.

Also note that now with the inline functions, timer_set_next_event
becomes more efficient in the lines of assembly code.

Signed-off-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>

This will allow us to share the code between system timer and
dmtimer device driver code without having to initialize all the
dmtimers early. This change will also make the timer_set_next_event
more efficient as the inline functions will optimize the code
better for the timer reprogramming.

Signed-off-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>

These will be needed when dmtimer platform init code gets split
for omap1 and omap2+. These will also be needed for separate
sys_timer init and driver init for the rest of the hardware timers
in the following patches. No functional changes.

Signed-off-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>

This is needed for the following patches so we can initialize the
rest of the hardware timers later on.

As with the init_irq calls, there's no need to do cpu_is_omap calls
during the timer init as we only care about the major omap generation.
This means that we can initialize the sys_timer with the .timer
entries alone.

Note that for now we just set stubs for the various sys_timer entries
that will get populated in a later patch. The following patches will
also remove the omap_dm_timer_init calls and change the init for the
rest of the hardware timers to happen with an arch_initcall.

Signed-off-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>

This allows us to remove cpu_is_omap calls from init_irq functions.
There should not be any need for cpu_is_omap calls as at this point.
During the timer init we only care about SoC generation, and not about
subrevisions.

The main reason for the patch is that we want to initialize only
minimal omap specific code from the init_early call.

Signed-off-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>

When runtime PM is disabled, device clocks need to be enabled on
device add and disabled on device remove.  This currently is not
happening because in the !PM_RUNTIME case, no notifiers are registered
for OMAP1 devices.

Fix this by ensuring notifiers are registered, even in the !PM_RUNTIME case.

Reported-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

CC: Mark Brown <broonie@opensource.wolfsonmicro.com>
CC: Mike Rapoport <mike@compulab.co.il>
CC: Nishant Kamat <nskamat@ti.com>
CC: Steve Sakoman <steve@sakoman.com>
CC: Felipe Balbi <balbi@ti.com>
Signed-off-by: Oleg Drokin <green@linuxhacker.ru>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

to use REGULATOR_SUPPLY arrays.

CC: Mark Brown <broonie@opensource.wolfsonmicro.com>
CC: Mike Rapoport <mike@compulab.co.il>
CC: Nishant Kamat <nskamat@ti.com>
CC: Steve Sakoman <steve@sakoman.com>
CC: Felipe Balbi <balbi@ti.com>
CC: Santosh Shilimkar <santosh.shilimkar@ti.com>
CC: peter.barada@logicpd.com
Signed-off-by: Oleg Drokin <green@linuxhacker.ru>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>