Radiotap is entirely little endian. Found with sparse.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Multiple issues:
 - there are no "default" values needed
 - cw_min/cw_max can be larger than documented
 - restructure to decrease size
 - use get_unaligned_le16

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch makes mac80211 assign proper sequence numbers to
QoS-data frames. It also removes the old sequence number code
because we noticed that only the driver or hardware can assign
sequence numbers to non-QoS-data and especially management
frames in a race-free manner because beacons aren't passed
through mac80211's TX path.

This patch also adds temporary code to the rt2x00 drivers to
not break them completely, that code will have to be reworked
for proper sequence numbers on beacons.

It also moves sequence number assignment down in the TX path
so no sequence numbers are assigned to frames that are dropped.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The /sys/class/net/*/wireless/ direcory is, as far as I know, not
used by anyone. Additionally, the same data is available via wext
ioctls. Hence the sysfs files are pretty much useless. This patch
makes them optional and schedules them for removal.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Jean Tourrilhes <jt@hpl.hp.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

According to 802.11-2007, we are doing the wrong thing in the
sequence number checks when receiving frames. This fixes it.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch fixes the check at the entrance to ieee80211_rx_reorder_ampdu.
This check has been broken by 'mac80211: rx.c use new helpers'.

Letting QoS NULL packet in ieee80211_rx_reorder_ampdu led to packet loss in
RX.

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

For RTL8187B it seems we need special values too for ANAPARAM*_OFF
values (and not use RTL8187 ones). The ANAPARAM*_OFF values used are the
stock ones read from the hardware after a cold boot.

Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Signed-off-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ssb.h implements DMA mapping functions, so it should
include dma-mapping.h. This fixes compile failures on certain architectures.

Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

With the new beacon handling from mac80211 we can
reorganize the beacon handling in rt2x00 as well.
This patch will move the function to the TX handlers,
and move all duplicate code into rt2x00queue.c.

After this change the descriptor helper functions
from rt2x00queue.c no longer need to be exported
outside of rt2x00lib and can be declared static.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Inform drivers about the changed CTS protection settings.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch changes mac80211's beacon configuration handling
to never pass skbs to the driver directly but rather always
require the driver to use ieee80211_beacon_get(). Additionally,
it introduces "change flags" on the config_interface() call
to enable drivers to figure out what is changing. Finally, it
removes the beacon_update() driver callback in favour of
having IBSS beacon delivered by ieee80211_beacon_get() as well.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch pushes the "netif_running()" and "same type as before"
checks down into ieee80211_if_change_type() to centralise the
logic instead of duplicating it for cfg80211 and wext.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch revamps the virtual interface handling and makes the
code much easier to follow. Fewer functions, better names, less
spaghetti code.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Currently, almost every interface type has a 'bss' pointer
pointing to BSS information. This BSS information, however,
is for a _local_ BSS, not for the BSS we joined, so having
it on a STA mode interface makes little sense, but now they
have it pointing to the master device, which is an AP mode
virtual interface. However, except for some bitrate control
data, this pointer is only used in AP/VLAN modes (for power
saving stations.)

Overall, it is not necessary to even have the master netdev
be a valid virtual interface, and it doesn't have to be on
the list of interfaces either.

This patch changes the master netdev to be special, it now
 - no longer is on the list of virtual interfaces, which
   lets me remove a lot of tests for that
 - no longer has sub_if_data attached, since that isn't used

Additionally, this patch changes some vlan/ap mode handling
that is related to these 'bss' pointers described above (but
in the VLAN case they actually make sense because there they
point to the AP they belong to); it also adds some debugging
code to IEEE80211_DEV_TO_SUB_IF to validate it is not called
on the master netdev any more.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

When CONFIG_HOTPLUG=n the following error occures on vmlinux linkage:

`.exit.text' referenced in section `.data' of drivers/built-in.o:
defined in discarded section `.exit.text' of drivers/built-in.o

'rtl8187_disconnect' function marked as __devexit isn't compiled with no
hotplug support. Added __devexit_p macros to fix the problem.

Signed-off-by: Ihar Hrachyshka <ihar.hrachyshka@promwad.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

As soon as an interface is enabled, and that interface is in adhoc or master mode,
the device will start raising beacondone interrupts. But before the first interrupt is
raised, mac80211 will probably not have send any beacons to the device yet, which
results in a NULL pointer error when the skb is being freed.

Note that the "raise beacondone interrupts without a beacon" is also a bug,
and will be addressed later. The more important bug however is preventing
the NULL pointer failt itself, since there might be other conditions that could trigger
it as well.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch implements the power management routines wireless extensions
for mac80211.
For now we only support switching PS mode between on and off.

Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: David S. Miller <davem@davemloft.net>

Multiple TX queue support is a core networking feature.

Signed-off-by: David S. Miller <davem@davemloft.net>

Accesses are mostly structured such that when there are multiple TX
queues the code transformations will be a little bit simpler.

Signed-off-by: David S. Miller <davem@davemloft.net>

This allows us to use this calling convention all the way down into
qdisc_restart().

Signed-off-by: David S. Miller <davem@davemloft.net>

Only plain netif_schedule() remains taking a net_device, mostly as a
compatability item while we transition the rest of these interfaces.

Everything else calls netif_schedule_queue() or __netif_schedule(),
both of which take a netdev_queue pointer.

Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: David S. Miller <davem@davemloft.net>

Accomplish this by using local variables.

Signed-off-by: David S. Miller <davem@davemloft.net>

This indicates if the NOOP scheduler is what is active for TX on a
given device.

Signed-off-by: David S. Miller <davem@davemloft.net>

First, we add a qdisc_tx_changing() helper which returns true if the
qdisc attachment is in transition.

Second, we remove an assertion warning which is of limited value and
is hard to express precisely in a multiqueue environment.

Signed-off-by: David S. Miller <davem@davemloft.net>

This is a helper function, currently used by IRDA.

This is being added so that we can contain and isolate as many
explicit ->tx_queue references in the tree as possible.

Signed-off-by: David S. Miller <davem@davemloft.net>

Isolate callers that want to simply reset all the TX qdiscs from the
details of TX queues.

Use this in the ISDN code.

Signed-off-by: David S. Miller <davem@davemloft.net>

We schedule queues, not the device, for output queue processing in BH.

Signed-off-by: David S. Miller <davem@davemloft.net>

It just wants the root qdisc given an arbitrary qdisc,
and that is simply qdisc->dev_queue->qdisc

Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>

It is always equal to qdisc->dev_queue->lock

Signed-off-by: David S. Miller <davem@davemloft.net>

Now that our qdisc management is bi-directional, per-queue, and fully
orthogonal, there is no reason to have a special ingress qdisc pointer
in struct net_device.

Signed-off-by: David S. Miller <davem@davemloft.net>

Now qdisc, qdisc_sleeping, and qdisc_list also live there.

Signed-off-by: David S. Miller <davem@davemloft.net>

Every qdisc is assosciated with a queue, and in the case of ingress
qdiscs that will now be netdev->rx_queue so using that queue's lock is
the thing to do.

Signed-off-by: David S. Miller <davem@davemloft.net>

The lock is now an attribute of the device queue.

One thing to notice is that "suspicious" places
emerge which will need specific training about
multiple queue handling.  They are so marked with
explicit "netdev->rx_queue" and "netdev->tx_queue"
references.

Signed-off-by: David S. Miller <davem@davemloft.net>

It can be obtained via the netdev_queue.  So create a helper routine,
qdisc_dev(), to make the transformations nicer looking.

Now, qdisc_alloc() now no longer needs a net_device pointer argument.

Signed-off-by: David S. Miller <davem@davemloft.net>

A netdev_queue is an entity managed by a qdisc.

Currently there is one RX and one TX queue, and a netdev_queue merely
contains a backpointer to the net_device.

The Qdisc struct is augmented with a netdev_queue pointer as well.

Eventually the 'dev' Qdisc member will go away and we will have the
resulting hierarchy:

	net_device --> netdev_queue --> Qdisc

Also, qdisc_alloc() and qdisc_create_dflt() now take a netdev_queue
pointer argument.

Signed-off-by: David S. Miller <davem@davemloft.net>

We haven't had netdev->tbusy in many years :)

Signed-off-by: David S. Miller <davem@davemloft.net>

Conflicts:

	drivers/net/wireless/iwlwifi/iwl-3945.c
	net/mac80211/mlme.c