The driver include <linux/gpio.h> yet does not use any
of the symbols from the header, so drop the include.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

The driver includes <linux/gpio.h> and <linux/of_gpio.h> yet
fails to use symbols from any of the include files, so drop
these includes.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

This driver is using the GPIO descriptor API but yet includes
the legacy <linux/gpio.h> header for no reason. Drop the
surplus include.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

The driver include <linux/gpio.h> yet does not use any
of the symbols from the header, so drop the include.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

The driver includes <linux/gpio.h> and <linux/of_gpio.h> yet
fails to use symbols from any of the include files, so drop
these includes.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Fix following checkpatch warning:

CHECK: Alignment should match open parenthesis
+static int st_lsm6dsx_read_event(struct iio_dev *iio_dev,
+                                  const struct iio_chan_spec *chan,

Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

The end-of-conversion (EOC) GPIO line is better to grab using
a GPIO descriptor. We drop the pdata for this: clients using board
files can use machine descriptor tables to pass this GPIO from
static data.

Cc: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

The device is always in a low-power state due to the hardware design. It
wakes up upon a conversion request and goes back into the low-power
state. The pm ops are added to disable the device completely and to free
the regulator. Disbaling the device completely should be not that
notable but freeing the regulator is important. Because if it is a shared
power-rail the regulator won't be disabled during suspend-to-ram/disk
and so all devices connected to that rail keeps on.

Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

commit f7072198 ("iio: imu: Fix inv_mpu6050 dependencies")
undid the explicit selection of I2C_MUX previously
done by the driver, because I2C_MUX implicitly depended
on HAS_IOMEM.

However commit 93d710a6

 ("i2c: mux: fix up dependencies")
cleared up the situation properly and drivers that need
to select I2C_MUX can now do so again.

It makes a lot of sense for a driver to select the driver
infrastructure it needs so restore the natural order of
things.

Cc: Richard Weinberger <richard@nod.at>
Cc: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

The channels specification assignment in chip info was simplified.
This patch makes supporting other devices by this driver easier.

Signed-off-by: Beniamin Bia <beniamin.bia@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Add support for parallax ping and laser ping sensors with just one pin
for trigger and echo signal.

This driver is based on srf04. In contrast to it it's necessary to
change direction of the pin and to request the irq just for the period
when the echo is rising and falling. Because this adds a lot of cases
there is this individual driver for handling this type of sensors.

Add a new configuration variable CONFIG_PING to Kconfig and Makefile.

Julia reported an issue with failing to unlock a mutex in some error
paths.

Signed-off-by: Andreas Klinger <ak@it-klinger.de>
Reported-by: kbuild test robot <lkp@intel.com>
Reported-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

There is no need to explicitly generate update event to update
timer master mode.

Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Adjust indentation from spaces to tab (+optional two spaces) as in
coding style with command like:
	$ sed -e 's/^        /\t/' -i */Kconfig

Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Add a maintainer for the new parallax PING))) and LaserPING IIO sensors

Signed-off-by: Andreas Klinger <ak@it-klinger.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Add dt-bindings for parallax PING))) and LaserPING iio sensors, which
are used for measuring distances.

Signed-off-by: Andreas Klinger <ak@it-klinger.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Add new vendor prefix parallax for newly created ping iio sensors.

Signed-off-by: Andreas Klinger <ak@it-klinger.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Previously, the code was using the of_read_property_bool() to check if
an external regulator was provided. However, this is redundant, as it's
more simple/direct to just ask the regulator is provided, via a
`devm_regulator_get_optional()` call.

Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Now the maxim_thermocouple has new, more specific, 'compatible' strings for
better distinguish the various supported chips.

This patch updates the DT bindings documentation accordingly

Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Cc: Colin Ian King <colin.king@canonical.com>
Cc: Patrick Havelange <patrick.havelange@essensium.com>
Cc: Matt Weber <matthew.weber@rockwellcollins.com>
Cc: Matt Ranostay <matt.ranostay@konsulko.com>
Cc: Chuhong Yuan <hslester96@gmail.com>
Cc: Daniel Gomez <dagmcr@gmail.com>
Cc: linux-iio@vger.kernel.org
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: devicetree@vger.kernel.org
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

We added a sysfs ABI for getting/setting the type of a thermocouple. This
driver supports chips that support specific fixed thermocouple types; we
cannot set it, but still we can add this sysfs attribute in RO mode to
read-back the thermocouple type.

This driver supports actually several chips:
 - max6675
 - max31855[k/j/n/s/t/e/r]asa family

Max6675 supports only K-type thermocouples, so we can just report that.

Each chip in max31855 family supports just one specific thermocouple type
(in the obvious way: i.e. max31855jasa supports J-type). This driver did
accept a generic SPI ID and OF compatible "max31855" which does not give
any clue about which chip is really involved (and unfortunately it seems
we have no way to detect it).

This patch introduces a new set of, more specific, SPI IDs and OF
compatible strings to better match the chip type.

The old, generic, "max31855" binding is kept for compatibility reasons, but
this patch aims to deprecate it, so, should we hit it, a warning is spit.
In such case the reported thermocouple type in sysfs is '?', because we
have no way to know.

Regarding the implementation: the thermocouple type information is stored
in the driver private data and I've kept only two maxim_thermocouple_chip
types in order to avoid a lot of duplications (seven chip types with just
a different thermocouple type).

RFT because I have no real HW to test this.

Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Cc: Colin Ian King <colin.king@canonical.com>
Cc: Patrick Havelange <patrick.havelange@essensium.com>
Cc: Matt Weber <matthew.weber@rockwellcollins.com>
Cc: Matt Ranostay <matt.ranostay@konsulko.com>
Cc: Chuhong Yuan <hslester96@gmail.com>
Cc: Daniel Gomez <dagmcr@gmail.com>
Cc: linux-iio@vger.kernel.org
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: devicetree@vger.kernel.org
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

The sensor support various thermocouple types (e.g. J, K, N, ...). The
driver allows to configure this parameter using a DT property.

This is useful when i.e. the thermocouple is physically tied to the sensor
and it is usually not removed, or when it is at least known in advance
which sensor will be connected to the circuit.

However, if the user can randomly connect any kind of thermocouples (i.e.
the device exposes a connector, and the user is free to connect its own
sensors), it would be more appropriate to provide a mechanism to
dynamically switch from one thermocouple type to another. This can be i.e.
handled in userspace by a GUI, a configuration file or a program that
detects the thermocouple type by reading a GPIO, or a eeprom on the probe,
or whatever.

This patch adds a IIO attribute that can be used to override, at run-time,
the DT-provided setting (which serves as default).

Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Cc: Colin Ian King <colin.king@canonical.com>
Cc: Patrick Havelange <patrick.havelange@essensium.com>
Cc: Matt Weber <matthew.weber@rockwellcollins.com>
Cc: Matt Ranostay <matt.ranostay@konsulko.com>
Cc: Chuhong Yuan <hslester96@gmail.com>
Cc: Daniel Gomez <dagmcr@gmail.com>
Cc: linux-iio@vger.kernel.org
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

IIO core layer gained a new sysfs standard attribute "thermocouple_type".
This patch adds it to the list of documented ABI for sysfs-bus-iio

Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Cc: Colin Ian King <colin.king@canonical.com>
Cc: Patrick Havelange <patrick.havelange@essensium.com>
Cc: Matt Weber <matthew.weber@rockwellcollins.com>
Cc: Matt Ranostay <matt.ranostay@konsulko.com>
Cc: Chuhong Yuan <hslester96@gmail.com>
Cc: Daniel Gomez <dagmcr@gmail.com>
Cc: linux-iio@vger.kernel.org
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

We have a couple of thermocouple IIO drivers, supporting several chips.
Some of them support only one specific thermocouple type (e.g. "K", "J"),
one of them can be configured to work with several different thermocouple
types.

In certain applications thermocouples could be externally connected to the
chip by the user.

This patch introduces a new IIO standard attribute to report the supported
thermocouple type and, where applicable, to allow it to be dynamically set
using sysfs.

Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Cc: Colin Ian King <colin.king@canonical.com>
Cc: Patrick Havelange <patrick.havelange@essensium.com>
Cc: Matt Weber <matthew.weber@rockwellcollins.com>
Cc: Matt Ranostay <matt.ranostay@konsulko.com>
Cc: Chuhong Yuan <hslester96@gmail.com>
Cc: Daniel Gomez <dagmcr@gmail.com>
Cc: linux-iio@vger.kernel.org
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

This patch introduces IIO_VAL_CHAR type for standard IIO attributes to
allow for attributes that needs to be represented by character rather
than a number. This is preparatory for introducing a new attribute whose
purpose is to describe thermocouple type, that can be i.e. "J", "K", etc..

The char-type value is stored in the first "value" integer that is passed
to the .[read/write]_raw() callbacks.

Note that in order to make it possible for the IIO core to correctly parse
this type (actually, to avoid integer parsing), it became mandatory for
any driver that wish to use IIO_VAL_CHAR on a writable attribute to
implement .write_raw_get_fmt().

Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Cc: Colin Ian King <colin.king@canonical.com>
Cc: Patrick Havelange <patrick.havelange@essensium.com>
Cc: Matt Weber <matthew.weber@rockwellcollins.com>
Cc: Matt Ranostay <matt.ranostay@konsulko.com>
Cc: Chuhong Yuan <hslester96@gmail.com>
Cc: Daniel Gomez <dagmcr@gmail.com>
Cc: linux-iio@vger.kernel.org
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

This sensor can perform samples averaging in hardware, but currently the
driver leaves this setting alone (default is no averaging).

This patch binds this HW setting to the "oversampling_ratio" IIO attribute
and allows the user to set the averaging as desired (the HW supports
averaging of 2, 5, 8 or 16 samples; in-between values are rounded up).

Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Cc: Colin Ian King <colin.king@canonical.com>
Cc: Patrick Havelange <patrick.havelange@essensium.com>
Cc: Matt Weber <matthew.weber@rockwellcollins.com>
Cc: Matt Ranostay <matt.ranostay@konsulko.com>
Cc: Chuhong Yuan <hslester96@gmail.com>
Cc: Daniel Gomez <dagmcr@gmail.com>
Cc: linux-iio@vger.kernel.org
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

max31856 IIO driver introduced a new attribute
"in_temp_filter_notch_center_frequency".
This patch adds it to the list of documented ABI for sysfs-bus-iio

Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Cc: Colin Ian King <colin.king@canonical.com>
Cc: Patrick Havelange <patrick.havelange@essensium.com>
Cc: Matt Weber <matthew.weber@rockwellcollins.com>
Cc: Matt Ranostay <matt.ranostay@konsulko.com>
Cc: Chuhong Yuan <hslester96@gmail.com>
Cc: Daniel Gomez <dagmcr@gmail.com>
Cc: linux-iio@vger.kernel.org
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

This sensor has an embedded notch filter for reducing interferences caused
by the power mains. This filter can be tuned to reject either 50Hz or 60Hz
(and harmonics).

Currently the said setting is left alone (the sensor defaults to 60Hz).
This patch introduces a IIO attribute that allows the user to set the said
filter to the desired frequency.

NOTE: this has been intentionally not tied to any DT property to allow
the configuration of this setting from userspace, e.g. with a GUI or by
reading a configuration file, or maybe reading a GPIO tied to a physical
switch or accessing some device that can autodetect the line frequency.

Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Cc: Colin Ian King <colin.king@canonical.com>
Cc: Patrick Havelange <patrick.havelange@essensium.com>
Cc: Matt Weber <matthew.weber@rockwellcollins.com>
Cc: Matt Ranostay <matt.ranostay@konsulko.com>
Cc: Chuhong Yuan <hslester96@gmail.com>
Cc: Daniel Gomez <dagmcr@gmail.com>
Cc: linux-iio@vger.kernel.org
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Reviewed-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

This change uses the ADIS library's state_lock to protect the state of the
`max_speed_hz` change that is done during the set of the sampling
frequency.

Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

It's the only operation that does 2 operations (a read & a write), so the
unlocked functions can be used under a single state lock.

Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

This replaces indio_dev's mlock with the state lock/mutex from the ADIS
library.

The __adis16136_get_freq() function has been prefixed to mark it as
unlocked. The adis16136_{set,get}_filter() functions now hold the state
lock for all the ops that they do.

Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

This change removes the use of indio_dev's mlock in favor using the state
lock from the ADIS library.

The set_freq() & get_freq() hooks are unlocked, so they require specific
locking. That is because in some cases the get_freq() hook is used in
combination with adis16400_set_filter().

In cases where only one read/write is done, the functions that hold the
state lock are used.

Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

The single conversion function does a series of reads + writes. This change
extends the use of the state_lock for the entire set of operations.
Previously, indio_dev's mlock was used. This change also removes the use of
this lock.

Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

The initial startup routine is called by some ADIS drivers during probe,
and before registering with IIO. Normally, userspace should not be able to
do any access to the device (as there shouldn't be any available).

This change extends the state lock to the entire initial-startup routine.
Behaviourally nothing should change, but this should make the library
function a bit more robust.

Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

The reset routine may also be important to be protected by the state-lock
and grouped with other operations, so create an unlocked version, so that
this can be done.

Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

This one also gets re-used in certain operations, so it makes sense to
have an unlocked version of this to group it with other
reads/writes/operations to have a single lock for the whole state change.

Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

The adis_enable_irq() does a read & a write. This change keeps a lock for
the duration of both operations vs for each op.

The change is also needed in adis16480, since that has it's own
implementation for adis_enable_irq().

Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

This will allow more flexible control to group reads & writes into a single
lock (particularly the state_lock).

The end-goal is to remove the indio_dev->mlock usage, and the simplest fix
would have been to just add another lock, which would not be a good idea on
the long-run.

Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

The lock can be extended a bit to protect other elements that are not
particular to just TX/RX. Another idea would have been to just add a new
`state_lock`, but that would mean 2 locks which would be redundant, and
probably cause more potential for dead-locks.

What will be done in the next patches, will be to add some unlocked
versions for read/write_reg functions.

Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

The relations between enum values and array indices values are currently
not enforced by the code, which makes them fragile w.r.t. future
changes.

Fix this by:
  1. Using designated array initializers, to make sure array indices and
     enums values match,
  2. Linking max9611_csa_gain enum values to the corresponding
     max9611_conf_ids enum values, as the latter is cast to the former
     in max9611_read_csa_voltage().

No change in generated code.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Acked-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Add support for driving MPU9150 magnetometer (AK8975) from mpu.

Signed-off-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

MPU9150 is i2c only.
Update Kconfig to delete in description chips that are i2c or
spi only.

Signed-off-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>