Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Noticed when setting SSP0 in clk_set_rate, _CLK_SET_RATE attempts to
reset the clock divider for the SSP0 parent clock, in this case
IO0FRAC. Bits 24-29 of HW_CLKCTRL_FRAC0 are cleared correctly, but
when the new frac value is written the value isn't shifted up to write
the correct bit-field.  This results in IO0FRAC being set to 0 and
CPUFRAC being corrupted.

This should occur when writing IO1FRAC, EMIFRAC in HW_CLKCTRL_FRAC0
and GPMIFRAC, HSADCFRAC in HW_CLKCTRL_FRAC1.

Tested on custom i.MX28 board with SSP0 SPI driver.

Signed-off-by: Matt Burtch <matt@grid-net.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

To configure pads during the initialisation a set of special constants
is used, e.g.
#define MX25_PAD_FEC_MDIO__FEC_MDIO IOMUX_PAD(0x3c4, 0x1cc, 0x10, 0, 0, PAD_CTL_HYS | PAD_CTL_PUS_22K_UP)

The problem is that no pull-up/down is getting activated unless both
PAD_CTL_PUE (pull-up enable) and PAD_CTL_PKE (pull/keeper module
enable) set. This is clearly stated in the i.MX25 datasheet and is
confirmed by the measurements on hardware. This leads to some rather
hard to understand bugs such as misdetecting an absent ethernet PHY (a
real bug i had), unstable data transfer etc. This might affect mx25,
mx35, mx50, mx51 and mx53 SoCs.

It's reasonable to expect that if the pullup value is specified, the
intention was to have it actually active, so we implicitly add the
needed bits.

Cc: stable@kernel.org
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

While suspending, we're enabling a clock in ->suspend() but we're in atomic
context, leading to this :

[30803.667305] PM: late suspend of devices complete after 1.237 msecs
[30803.667449] BUG: sleeping function called from invalid context at kernel/mutex.c:271
[30803.667464] in_atomic(): 0, irqs_disabled(): 128, pid: 4941, name: pm-suspend
[30803.667474] INFO: lockdep is turned off.
[30803.667483] irq event stamp: 0
[30803.667489] hardirqs last  enabled at (0): [<  (null)>]   (null)
[30803.667503] hardirqs last disabled at (0): [<c001e4a8>] copy_process.part.48+0x1e0/0xa7c
[30803.667543] softirqs last  enabled at (0): [<c001e4a8>] copy_process.part.48+0x1e0/0xa7c
[30803.667562] softirqs last disabled at (0): [<  (null)>]   (null)
[30803.667574] Backtrace:
[30803.667611] [<c0010e00>] (dump_backtrace+0x0/0x110) from [<c0424c00>] (dump_stack+0x18/0x1c)
[30803.667624]  r6:00000000 r5:00000000 r4:d9648000 r3:d9648000
[30803.667652] [<c0424be8>] (dump_stack+0x0/0x1c) from [<c0424eec>] (__might_sleep.part.101+0x90/0xa8)
[30803.667673] [<c0424e5c>] (__might_sleep.part.101+0x0/0xa8) from [<c001a5c4>] (__might_sleep+0x80/0x94)
[30803.667686]  r4:c05d58c0
[30803.667705] [<c001a544>] (__might_sleep+0x0/0x94) from [<c043230c>] (mutex_lock_nested+0x2c/0x30c)
[30803.667735] [<c04322e0>] (mutex_lock_nested+0x0/0x30c) from [<c0017834>] (clk_enable+0x28/0x50)
[30803.667747]  r8:c0438464 r7:00000003 r6:00000000 r5:00000000 r4:c05d2e98
[30803.667780] [<c001780c>] (clk_enable+0x0/0x50) from [<c0017260>] (mx5_suspend_enter+0x1c/0x98)
[30803.667792]  r4:00000003 r3:c060dfe0
[30803.667821] [<c0017244>] (mx5_suspend_enter+0x0/0x98) from [<c0059b48>] (suspend_enter+0xec/0x15c)
[30803.667833]  r4:00000003 r3:c0017244
[30803.667856] [<c0059a5c>] (suspend_enter+0x0/0x15c) from [<c0059c4c>] (suspend_devices_and_enter+0x94/0x130)
[30803.667868]  r6:00000000 r5:00000003 r4:c0c0af00 r3:00002710
[30803.667897] [<c0059bb8>] (suspend_devices_and_enter+0x0/0x130) from [<c0059db0>] (enter_state+0xc8/0x130)
[30803.667909]  r6:00000000 r5:00000003 r4:c05286e4
[30803.667934] [<c0059ce8>] (enter_state+0x0/0x130) from [<c00592d4>] (state_store+0xac/0xc0)
[30803.667945]  r6:00000003 r5:00000003 r4:df39d000 r3:00000003
[30803.667978] [<c0059228>] (state_store+0x0/0xc0) from [<c01b0100>] (kobj_attr_store+0x1c/0x28)
[30803.668009] [<c01b00e4>] (kobj_attr_store+0x0/0x28) from [<c00e435c>] (sysfs_write_file+0x88/0xbc)
[30803.668032] [<c00e42d4>] (sysfs_write_file+0x0/0xbc) from [<c0091fa0>] (vfs_write+0xbc/0x138)
[30803.668051] [<c0091ee4>] (vfs_write+0x0/0x138) from [<c0092204>] (sys_write+0x44/0x70)
[30803.668062]  r8:00000000 r7:00000004 r6:00000003 r5:002694d0 r4:d966acc0
[30803.668094] [<c00921c0>] (sys_write+0x0/0x70) from [<c000db00>] (ret_fast_syscall+0x0/0x3c)
[30803.668106]  r9:d9648000 r8:c000dcc4 r6:00000001 r5:002694d0 r4:00000003
[30803.669927] PM: early resume of devices complete after 0.972 msecs

Just move the clk_enable/disable in ->prepare() and ->finish()

Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>

Defconfig file for at91sam9g45 SoC family:
at91sam9g45, at91sam9g46, at91sam9m10, at91sam9m11.
The Atmel Evaluation Kit for this family is the at91sam9m10g45ek.

It is so useful for automatic compile tests...

Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

Remove dependency line which was not including the SAM9G45.

[arnd: added dependency on HAVE_CLK to avoid breaking other machines]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

This applies ARM errata fix 754322 for all ux500 platforms.

Cc: stable@kernel.org
Signed-off-by: srinidhi kasagar <srinidhi.kasagar@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

* git://github.com/davem330/net:
  pch_gbe: Fixed the issue on which a network freezes
  pch_gbe: Fixed the issue on which PC was frozen when link was downed.
  make PACKET_STATISTICS getsockopt report consistently between ring and non-ring
  net: xen-netback: correctly restart Tx after a VM restore/migrate
  bonding: properly stop queuing work when requested
  can bcm: fix incomplete tx_setup fix
  RDSRDMA: Fix cleanup of rds_iw_mr_pool
  net: Documentation: Fix type of variables
  ibmveth: Fix oops on request_irq failure
  ipv6: nullify ipv6_ac_list and ipv6_fl_list when creating new socket
  cxgb4: Fix EEH on IBM P7IOC
  can bcm: fix tx_setup off-by-one errors
  MAINTAINERS: tehuti: Alexander Indenbaum's address bounces
  dp83640: reduce driver noise
  ptp: fix L2 event message recognition

* 'fix/asoc' of git://github.com/tiwai/sound:
  ASoC: omap_mcpdm_remove cannot be __devexit
  ASoC: Fix setting update bits for WM8753_LADC and WM8753_RADC
  ASoC: use a valid device for dev_err() in Zylonite

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
  drm/radeon/kms: fix channel_remap setup (v2)
  drm/radeon: Set cursor x/y to 0 when x/yorigin > 0.
  drm/radeon: Update AVIVO cursor coordinate origin before x/yorigin calculation.
  drm/radeon: Simplify cursor x/yorigin calculation.
  drm/radeon/kms: fix cursor image off-by-one error
  drm/radeon/kms: Fix logic error in DP HPD handler
  drm/radeon/kms: add retry limits for native DP aux defer
  drm/radeon/kms: fix regression in DP aux defer handling

* 'spi/merge' of git://git.secretlab.ca/git/linux-2.6:
  spi-topcliff-pch: Fix overrun issue
  spi-topcliff-pch: Add recovery processing in case FIFO overrun error occurs
  spi-topcliff-pch: Fix CPU read complete condition issue
  spi-topcliff-pch: Fix SSN Control issue
  spi-topcliff-pch: add tx-memory clear after complete transmitting

Add the ability to disable PCI-E MPS turning and using the BIOS
configured MPS defaults.  Due to the number of issues recently
discovered on some x86 chipsets, make this the default behavior.

Also, add the option for peer to peer DMA MPS configuration.  Peer to
peer DMA is outside the scope of this patch, but MPS configuration could
prevent it from working by having the MPS on one root port different
than the MPS on another.  To work around this, simply make the system
wide MPS the smallest possible value (128B).

Signed-off-by: Jon Mason <mason@myri.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Most asics just use the hw default value which requires
no explicit programming.  For those that need a different
value, the vbios will program it properly.  As such,
there's no need to program these registers explicitly
in the driver.  Changing MC_SHARED_CHREMAP requires a reload
of all data in vram otherwise its contents will be scambled.

Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=40103



v2: drop now unused channel_remap functions.

Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>

We found that adding load, Rx data sometimes drops.(with DMA transfer mode)
The cause is that before starting Rx-DMA processing, Tx-DMA processing starts.
This causes FIFO overrun occurs.

This patch fixes the issue by modifying FIFO tx-threshold and DMA descriptor
size like below.

                      Current                   this patch
Rx-descriptor   4Byte+12Byte*341    -->    12Byte*340-4Byte-12Byte
Rx-threshold                   (Not modified)
Tx-descriptor   4Byte+12Byte*341    -->    16Byte-12Byte*340
Rx-threshold    12Byte              -->    2Byte

Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>

Add recovery processing in case FIFO overrun error occurs with DMA transfer mode.

Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>

We found Rx data sometimes drops.(with non-DMA transfer mode)
The cause is read complete condition is not true.

This patch fixes the issue.

Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>

During processing 1 command/data series,
SSN should keep LOW.
However, currently, SSN becomes HIGH.
This patch fixes the issue.

Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>

Currently, in case of reading date from SPI flash,
command is sent twice.
The cause is that tx-memory clear processing is missing .
This patch adds the tx-momory clear processing.

Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>

Commit 2a7fade7

 ("hwmon: lis3: Power on corrections") caused a
regression on HP laptops with 8bit chip.  Writing CTRL2_BOOT_8B bit seems
clearing the BIOS setup, and no proper interrupt for DriveGuard will be
triggered any more.

Since the init code there is basically only for embedded devices, put a
pdata check so that the problematic initialization will be skipped for
hp_accel stuff.

Signed-off-by: Takashi Iwai <tiwai@suse.de>
Cc: Eric Piel <eric.piel@tremplin-utc.net>
Cc: Samu Onkalo <samu.p.onkalo@nokia.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'hwmon-for-linus' of git://github.com/groeck/linux:
  hwmon: (coretemp) Avoid leaving around dangling pointer
  hwmon: (coretemp) Fixup platform device ID change

* git://github.com/davem330/ide:
  ide-disk: Fix request requeuing

* 'btrfs-3.0' of git://github.com/chrismason/linux:
  Btrfs: force a page fault if we have a shorty copy on a page boundary

Fixes bug where variable i was redundantly used for counting two nested loops.

Signed-off-by: Tapani Utriainen <tapani@technexion.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

`keypad_pads' is referred to by `keypad_data' which is
not __initdata, so `keypad_pads' should not be __initdata either.

Signed-off-by: Bjarne Steinsbo <bsteinsbo@gmail.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Simon Kirby reported that on his RAID setup with idedisk underneath
the box OOMs after a couple of days of runtime. Running with
CONFIG_DEBUG_KMEMLEAK pointed to idedisk_prep_fn() which unconditionally
allocates an ide_cmd struct. However, ide_requeue_and_plug() can be
called more than once per request, either from the request issue or the
IRQ handler path and do blk_peek_request() ends up in idedisk_prep_fn()
repeatedly, allocating a struct ide_cmd everytime and "forgetting" the
previous pointer.

Make sure the code reuses the old allocated chunk.

Reported-and-tested-by: Simon Kirby <sim@hostway.ca>
Cc: <stable@kernel.org> [ 39.x, 3.0.x ]
Link: http://marc.info/?l=linux-kernel&m=131667641517919
Link: http://lkml.kernel.org/r/20110922072643.GA27232@hostway.ca


Signed-off-by: Borislav Petkov <bp@alien8.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

The pch_gbe driver has an issue which a network stops,
when receiving traffic is high.
In the case, The link down and up are necessary to return a network.

This patch fixed this issue.

Signed-off-by: Toshiharu Okada <toshiharu-linux@dsn.okisemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When a link was downed during network use,
there is an issue on which PC freezes.

This patch fixed this issue.

Signed-off-by: Toshiharu Okada <toshiharu-linux@dsn.okisemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This is a minor change.

Up until kernel 2.6.32, getsockopt(fd, SOL_PACKET, PACKET_STATISTICS,
...) would return total and dropped packets since its last invocation. The
introduction of socket queue overflow reporting [1] changed drop
rate calculation in the normal packet socket path, but not when using a
packet ring. As a result, the getsockopt now returns different statistics
depending on the reception method used. With a ring, it still returns the
count since the last call, as counts are incremented in tpacket_rcv and
reset in getsockopt. Without a ring, it returns 0 if no drops occurred
since the last getsockopt and the total drops over the lifespan of
the socket otherwise. The culprit is this line in packet_rcv, executed
on a drop:

drop_n_acct:
        po->stats.tp_drops = atomic_inc_return(&sk->sk_drops);

As it shows, the new drop number it taken from the socket drop counter,
which is not reset at getsockopt. I put together a small example
that demonstrates the issue [2]. It runs for 10 seconds and overflows
the queue/ring on every odd second. The reported drop rates are:
ring: 16, 0, 16, 0, 16, ...
non-ring: 0, 15, 0, 30, 0, 46, 0, 60, 0 , 74.

Note how the even ring counts monotonically increase. Because the
getsockopt adds tp_drops to tp_packets, total counts are similarly
reported cumulatively. Long story short, reinstating the original code, as
the below patch does, fixes the issue at the cost of additional per-packet
cycles. Another solution that does not introduce per-packet overhead
is be to keep the current data path, record the value of sk_drops at
getsockopt() at call N in a new field in struct packetsock and subtract
that when reporting at call N+1. I'll be happy to code that, instead,
it's just more messy.

[1] http://patchwork.ozlabs.org/patch/35665/
[2] http://kernel.googlecode.com/files/test-packetsock-getstatistics.c



Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If a VM is saved and restored (or migrated) the netback driver will no
longer process any Tx packets from the frontend.  xenvif_up() does not
schedule the processing of any pending Tx requests from the front end
because the carrier is off.  Without this initial kick the frontend
just adds Tx requests to the ring without raising an event (until the
ring is full).

This was caused by 47103041

 (net:
xen-netback: convert to hw_features) which reordered the calls to
xenvif_up() and netif_carrier_on() in xenvif_connect().

Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Cc: Ian Campbell <ian.campbell@citrix.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

During a test where a pair of bonding interfaces using ARP monitoring
were both brought up and torn down (with an rmmod) repeatedly, a panic
in the timer code was noticed.  I tracked this down and determined that
any of the bonding functions that ran as workqueue handlers and requeued
more work might not properly exit when the module was removed.

There was a flag protected by the bond lock called kill_timers that is
set when the interface goes down or the module is removed, but many of
the functions that monitor link status now unlock the bond lock to take
rtnl first.  There is a chance that another CPU running the rmmod could
get the lock and set kill_timers after the first check has passed.

This patch does not allow any function to queue work that will make
itself run unless kill_timers is not set.  I also noticed while doing
this work that bond_resend_igmp_join_requests did not have a check for
kill_timers, so I added the needed call there as well.

Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Reported-by: Liang Zheng <lzheng@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Apart from the obvious cleanup, this should make the line

			cursor_end = x - xorigin + w;

correct now.

Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

Fixes cursor disappearing prematurely when moving off a top/left edge which
is not located at the desktop top/left edge.

Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Cc: stable@kernel.org
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

The mouse cursor hotspot calculation when the cursor is partially off the
top or left side of the screen was off by one.

Fixes https://bugs.freedesktop.org/show_bug.cgi?id=41158



Signed-off-by: Nicholas Miell <nmiell@gmail.com>
Reviewed-by: Michel Dänzer <michel@daenzer.net>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

Only disable the pipe if the monitor is physically
disconnected.  The previous logic also disabled the
pipe if the link was trained.

Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=41248



Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>