NOTICE THAT:

"...we don't know whether we need fallthroughs or breaks here and this
is just a change to avoid having new warnings when switching to
-Wimplicit-fallthrough but this change might be entirely wrong."[1]

See the original thread of discussion here:

https://lore.kernel.org/patchwork/patch/1036251/

So, in preparation to enabling -Wimplicit-fallthrough, this patch silences
the following warnings:

drivers/mtd/nand/onenand/onenand_base.c: In function ‘onenand_check_features’:
drivers/mtd/nand/onenand/onenand_base.c:3264:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
   if (ONENAND_IS_DDP(this))
      ^
drivers/mtd/nand/onenand/onenand_base.c:3284:2: note: here
  case ONENAND_DEVICE_DENSITY_2Gb:
  ^~~~
drivers/mtd/nand/onenand/onenand_base.c:3288:17: warning: this statement may fall through [-Wimplicit-fallthrough=]
   this->options |= ONENAND_HAS_UNLOCK_ALL;
drivers/mtd/nand/onenand/onenand_base.c:3290:2: note: here
  case ONENAND_DEVICE_DENSITY_1Gb:
  ^~~~

Warning level 3 was used: -Wimplicit-fallthrough=3

Also, notice that this patch doesn't change any functionality. See the
most recent thread of discussion here:

https://lore.kernel.org/patchwork/patch/1077395/

This patch is part of the ongoing efforts to enable
-Wimplicit-fallthrough.

[1] https://lore.kernel.org/lkml/20190509085318.34a9d4be@xps13/



Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Suggested-by: Boris Brezillon <boris.brezillon@collabora.com>
Suggested-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>

The GigaDevice GD5F1GQ4UFxxG SPI NAND is in current production devices
and, while it has the same logical layout as the E-series devices,
it differs in the SPI interfacing in significant ways.

This support is contingent on previous commits to:

  * Add support for two-byte device IDs
  * Define macros for page-read ops with three-byte addresses

http://www.gigadevice.com/datasheet/gd5f1gq4xfxxg/



Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>

The GigaDevice GD5F1GQ4UFxxG SPI NAND utilizes two-byte device IDs.

http://www.gigadevice.com/datasheet/gd5f1gq4xfxxg/



Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>

The GigaDevice GD5F1GQ4UFxxG SPI NAND utilizes three-byte addresses
for its page-read ops.

http://www.gigadevice.com/datasheet/gd5f1gq4xfxxg/



Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>

This change supports nand-ecc-step-size and nand-ecc-strength fields in
brcmnand DT node to be optional.
see: Documentation/devicetree/bindings/mtd/brcm,brcmnand.txt

If both nand-ecc-strength and nand-ecc-step-size are not specified in
device tree node for NAND, raw NAND layer does detect ECC information by
reading ONFI extended parameter page for parts using ONFI >= 2.1.
In case of non-ONFI NAND parts there could be a nand_id table entry with
ECC information. If there is valid device tree entry for nand-ecc-strength
and nand-ecc-step-size fields it still shall override the detected values.

Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>

nand-ecc-strength and nand-ecc-step-size can be made optional as
brcmnand driver can support using raw NAND layer detected values.

Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>

The gpmi driver performance suffers from NAND operations being split
in multiple small DMA transfers. This has been forced by the NAND layer
in the former days, but now with exec_op we can use the controller as
intended.

With this patch gpmi_nfc_exec_op becomes the main entry point to NAND
operations. Here all instructions are collected and chained as separate
DMA transfers. In the end whole chain is fired and waited to be
finished. gpmi_nfc_exec_op only does the hardware operations, bad block
marker swapping and buffer scrambling is done by the callers. It's worth
noting that the nand_*_op functions always take the buffer lengths for
the data that the NAND chip actually transfers. When doing BCH we have
to calculate the net data size from the raw data size in some places.

This patch has been tested with 2048/64 and 2048/128 byte NAND on
i.MX6q. mtd_oobtest, mtd_subpagetest and mtd_speedtest run without
errors. nandbiterrs, nandpagetest and nandsubpagetest userspace tests
from mtdutils run without errors and UBIFS can successfully be mounted.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>

The mxs dma driver uses the flags parameter in dmaengine_prep_slave_sg() for
custom flags, but still uses the dmaengine specific names of the flags.
Do a little bit better and at least give the flag a custom name.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>

The mxs dma driver can do PIO transfers. A pointer to the PIO words
to transfer is passed in the struct scatterlist * argument of
dmaengine_prep_slave_sg(). It's quite ugly and non obvious to cast
u32 * to struct scatterlist * each time when calling
dmaengine_prep_slave_sg(), so add a static inline wrapper function
to be called by the user along with a description what is going on.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>

The DMA_PREP_INTERRUPT flag is no longer needed by the mxs DMA driver,
drop it.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>

The mxs dma driver insists on having the DMA_PREP_INTERRUPT flag set
on all but the first transfer. There's no need to let the user set this
flag, the driver can do it internally whenever it needs it. Drop
handling of this flag from the driver.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>

The gpmi driver aggressively en/disables the clocks between operations
which has significant performance cost. Use runtime PM to get rid of
this bottleneck.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>

The i.MX23 specific option read code is called right after nand_scan. We
can rely on the NAND core having disabled the chipselect, so there's no
point in restoring the original chip select after NAND operations. Drop
it.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>

gpmi_ecc_read_page_data uses the page parameter only for a debug printf,
so we can drop the parameter and the debug printf. Moving the oob
delivery from gpmi_ecc_read_page_data to gpmi_ecc_read_page makes the
oob_required parameter unnecessary aswell.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>

The driver calls nand_read_page_op without a buffer passed and then
calls chip->legacy.read_buf to read the buffer afterwards which is
the same as passing the buffer nand_read_page_op in the first place.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>

this->page_buffer_virt and this->payload_virt are always set to the same
value, so drop the former and just use the latter. Same for
this->page_buffer_virt and this->payload_virt.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>

The "private" member of struct gpmi_nand_data isn't used anywhere.
Remove it.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>

This moves the whole driver into a single C file. The filename gpmi-lib
implies that it implements library functions, but in fact there are
several cases where functions in gpmi-lib.c call back into functions in
gpmi-nand.c. With this one has to constantly jump between those two
files, so moving it into a single file improves readability, even when
the file gets quite large.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>

Replace the different operation tracing functions with a call to
nand_op_trace.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>

The NAND core has a NAND operation tracing function, but it can only
be used by drivers using the generic option parser from the NAND core.
Export the tracing function as a static inline function in rawnand.h
so that drivers implementing exec_op directly do not have to write their
own operation tracing.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>

One main goal of the function mtk_nfc_update_ecc_stats is to check
whether sectors are all empty. If they are empty, set these sectors's
data buffer and OOB buffer as 0xff.

But now, the sector OOB buffer pointer is wrongly assigned. We always
do memset from sector 0.

To fix this issue, pass start sector number to make OOB buffer pointer
be properly assigned.

Fixes: 1d6b1e46

 ("mtd: mediatek: driver for MTK Smart Device")
Signed-off-by: Xiaolei Li <xiaolei.li@mediatek.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>

Currently, we only check how many CE# pins are set in device tree.
But it should be necessary to check whether CE# pin setting is
duplicated or if CE# pin index exceeds the maximum CE# number that
controller supports.

So, add validity check to avoid these invalid settings.

Signed-off-by: Xiaolei Li <xiaolei.li@mediatek.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>

Currently, we expand RE# low level time by choosing the max value
between RE# pulse width and RE# access time, and sample data at the
rising edge of RE#.

Then, if RE# access time is bigger than RE# pulse width, the real
read cycle time may be more than NAND SPEC required. This makes
read performance be worse than that expected.

This patch improves data sampling timing by calculating RE# low level
time according to RE# pulse width. If RE# access time is bigger than
RE# pulse width, then delay sampling data timing.

The result of contrast test base on MT2712 evaluat board is as follow.

nand: Micron MT29F16G08ADBCAH4
nand: 2048 MiB, SLC, erase size: 256 KiB, page size: 4096, OOB size: 224
NFI 2x clock rate: 124800000 HZ.

Read speed without this patch:
mtd_speedtest: page read speed is 14012 KiB/s
mtd_speedtest: 2 page read speed is 14860 KiB/s

Read speed with this patch:
mtd_speedtest: page read speed is 18724 KiB/s
mtd_speedtest: 2 page read speed is 18713 KiB/s

Signed-off-by: Xiaolei Li <xiaolei.li@mediatek.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>

At present, the flow of calculating AC timing of read/write cycle in SDR
mode is that:
At first, calculate high hold time which is valid for both read and write
cycle using the max value between tREH_min and tWH_min.
Secondly, calculate WE# pulse width using tWP_min.
Thridly, calculate RE# pulse width using the bigger one between tREA_max
and tRP_min.

But NAND SPEC shows that Controller should also meet write/read cycle time.
That is write cycle time should be more than tWC_min and read cycle should
be more than tRC_min. Obviously, we do not achieve that now.

This patch corrects the low level time calculation to meet minimum
read/write cycle time required. After getting the high hold time, WE# low
level time will be promised to meet tWP_min and tWC_min requirement,
and RE# low level time will be promised to meet tREA_max, tRP_min and
tRC_min requirement.

Fixes: edfee361

 ("mtd: nand: mtk: add ->setup_data_interface() hook")
Cc: stable@vger.kernel.org # v4.17+
Signed-off-by: Xiaolei Li <xiaolei.li@mediatek.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>

The way oobregion->offset is derived for large page NAND parts is
wrong, fixes it.

Fixes: ef5eeea6

 ("mtd: nand: brcm: switch to mtd_ooblayout_ops")
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>

Used in several S5PV210-based Galaxy S devices, among them SGH-T959V,
SGH-T959P, SGH-T839, and SPH-D700.

Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>

During probe, check the "get_irq" error value.

Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Acked-by: Christophe Kerello <christophe.kerello@st.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>

Sometimes the exec_op parser does not choose the optimal pattern if
multiple patterns with optional elements are available. Since the stack
automatically splits operations in multiple exec_op calls, a non-optimal
pattern gets broken up into multiple calls. E.g. an OOB read using the
vf610 driver:
  nand: executing subop:
  nand:     ->CMD      [0x00]
  nand:     ->ADDR     [5 cyc: 00 08 ea 94 02]
  nand:     ->CMD      [0x30]
  nand:     ->WAITRDY  [max 200000 ms]
  nand:       DATA_IN  [64 B]
  nand: executing subop:
  nand:       CMD      [0x00]
  nand:       ADDR     [5 cyc: 00 08 ea 94 02]
  nand:       CMD      [0x30]
  nand:       WAITRDY  [max 200000 ms]
  nand:     ->DATA_IN  [64 B]

However, the vf610 driver has a pattern which can execute the complete
command in a single go...

This patch makes sure that the longest matching pattern is chosen
instead of the first (potentially only partial) match. With this
change the vf610 reads the OOB in a single exec_op call:
  nand: executing subop:
  nand:     ->CMD      [0x00]
  nand:     ->ADDR     [5 cyc: 00 08 c0 1d 00]
  nand:     ->CMD      [0x30]
  nand:     ->WAITRDY  [max 200000 ms]
  nand:     ->DATA_IN  [64 B]

Reported-by: Sascha Hauer <s.hauer@pengutronix.de>
Suggested-by: Boris Brezillon <boris.brezillon@collabora.com>
Tested-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>

Pull x86 fixes from Ingo Molnar:
 "Two fixes: a quirk for KVM guests running on certain AMD CPUs, and a
  KASAN related build fix"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/CPU/AMD: Don't force the CPB cap when running under a hypervisor
  x86/boot: Provide KASAN compatible aliases for string routines

Pull perf fixes from Ingo Molnar:
 "On the kernel side there's a bunch of ring-buffer ordering fixes for a
  reproducible bug, plus a PEBS constraints regression fix.

  Plus tooling fixes"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  tools headers UAPI: Sync kvm.h headers with the kernel sources
  perf record: Fix s390 missing module symbol and warning for non-root users
  perf machine: Read also the end of the kernel
  perf test vmlinux-kallsyms: Ignore aliases to _etext when searching on kallsyms
  perf session: Add missing swap ops for namespace events
  perf namespace: Protect reading thread's namespace
  tools headers UAPI: Sync drm/drm.h with the kernel
  tools headers UAPI: Sync drm/i915_drm.h with the kernel
  tools headers UAPI: Sync linux/fs.h with the kernel
  tools headers UAPI: Sync linux/sched.h with the kernel
  tools arch x86: Sync asm/cpufeatures.h with ...

Pull EFI fixes from Ingo Molnar:
 "Two EFI fixes: a quirk for weird systabs, plus add more robust error
  handling in the old 1:1 mapping code"

* 'efi-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  efi: Allow the number of EFI configuration tables entries to be zero
  efi/x86/Add missing error handling to old_memmap 1:1 mapping code

Pull stacktrace fix from Ingo Molnar:
 "Fix a stack_trace_save_tsk_reliable() regression"

* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  stacktrace: Unbreak stack_trace_save_tsk_reliable()

Pull SPDX fixes from Greg KH:
 "Here are just two small patches, that fix up some found SPDX
  identifier issues.

  The first patch fixes an error in a previous SPDX fixup patch, that
  causes build errors when doing 'make clean' on the tree (the fact that
  almost no one noticed it reflects the fact that kernel developers
  don't like doing that option very often...)

  The second patch fixes up a number of places in the tree where people
  mistyped the string "SPDX-License-Identifier". Given that people can
  not even type their own name all the time without mistakes, this was
  bound to happen, and odds are, we will have to add some type of check
  for this to checkpatch.pl to catch this happening in the future.

  Both of these have passed testing by 0-day"

* tag 'spdx-5.2-rc3-2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
  treewide: fix typos of SPDX-License-Identifier
  crypto: ...

Pull powerpc fixes from Michael Ellerman:
 "A minor fix to our IMC PMU code to print a less confusing error
  message when the driver can't initialise properly.

  A fix for a bug where a user requesting an unsupported branch sampling
  filter can corrupt PMU state, preventing the PMU from counting
  properly.

  And finally a fix for a bug in our support for kexec_file_load(),
  which prevented loading a kernel and initramfs. Most versions of kexec
  don't yet use kexec_file_load().

  Thanks to: Anju T Sudhakar, Dave Young, Madhavan Srinivasan, Ravi
  Bangoria, Thiago Jung Bauermann"

* tag 'powerpc-5.2-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  powerpc/kexec: Fix loading of kernel + initramfs with kexec_file_load()
  powerpc/perf: Fix MMCRA corruption by bhrb_filter
  powerpc/powernv: Return for invalid IMC domain

Pull KVM fixes from Paolo Bonzini:
 "Fixes for PPC and s390"

* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
  KVM: PPC: Book3S HV: Restore SPRG3 in kvmhv_p9_guest_entry()
  KVM: PPC: Book3S HV: Fix lockdep warning when entering guest on POWER9
  KVM: PPC: Book3S HV: XIVE: Fix page offset when clearing ESB pages
  KVM: PPC: Book3S HV: XIVE: Take the srcu read lock when accessing memslots
  KVM: PPC: Book3S HV: XIVE: Do not clear IRQ data of passthrough interrupts
  KVM: PPC: Book3S HV: XIVE: Introduce a new mutex for the XIVE device
  KVM: PPC: Book3S HV: XIVE: Fix the enforced limit on the vCPU identifier
  KVM: PPC: Book3S HV: XIVE: Do not test the EQ flag validity when resetting
  KVM: PPC: Book3S HV: XIVE: Clear file mapping when device is released
  KVM: PPC: Book3S HV: Don't take kvm->lock around kvm_for_each_vcpu
  KVM: PPC: Book3S: Use new mutex to synchronize access to rtas token list
  KVM: PPC: Book3S HV: Use ne...

Pull i2c fixes from Wolfram Sang:
 "A memleak fix for the core, two driver bugfixes, as well as fixing
  missing file patterns to MAINTAINERS"

* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  MAINTAINERS: add I2C DT bindings to ARM platforms
  MAINTAINERS: add DT bindings to i2c drivers
  i2c: synquacer: fix synquacer_i2c_doxfer() return value
  i2c: mlxcpld: Fix wrong initialization order in probe
  i2c: dev: fix potential memory leak in i2cdev_ioctl_rdwr

Pull thermal SoC fix from Eduardo Valentin:
 "A single revert, detected to cause issues on the tsens driver"

* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/evalenti/linux-soc-thermal:
  Revert "drivers: thermal: tsens: Add new operation to check if a sensor is enabled"

Merge tag 'led-fixes-for-5.2-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds

Pull LED fix from Jacek Anaszewski:
 "Fix for a recent change in LED core, that didn't take into account the
  possibility of calling led_blink_setup() from atomic context"

* tag 'led-fixes-for-5.2-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds:
  leds: avoid flush_work in atomic context

Pull block fixes from Jens Axboe:

 - A set of patches fixing code comments / kerneldoc (Bart)

 - Don't allow loop file change for exclusive open (Jan)

 - Fix revalidate of hidden genhd (Jan)

 - Init queue failure memory free fix (Jes)

 - Improve rq limits failure print (John)

 - Fixup for queue removal/addition (Ming)

 - Missed error progagation for io_uring buffer registration (Pavel)

* tag 'for-linus-20190601' of git://git.kernel.dk/linux-block:
  block: print offending values when cloned rq limits are exceeded
  blk-mq: Document the blk_mq_hw_queue_to_node() arguments
  blk-mq: Fix spelling in a source code comment
  block: Fix bsg_setup_queue() kernel-doc header
  block: Fix rq_qos_wait() kernel-doc header
  block: Fix blk_mq_*_map_queues() kernel-doc headers
  block: Fix throtl_pending_timer_fn() kernel-doc header
  block: Convert blk_invalidate_devt() header into a non-kernel-doc header
  block/partitions/ldm: Convert a kernel-doc header into a non-kernel-doc header
  blk-mq: Fix memory leak in error handling
  block: don't protect generic_make_request_checks with blk_queue_enter
  block: move blk_exit_queue into __blk_release_queue
  block: Don't revalidate bdev of hidden gendisk
  loop: Don't change loop device under exclusive opener
  io_uring: Fix __io_uring_register() false success