- Aug 23, 2013
-
-
Arend van Spriel authored
The baseband multiplier must be zero during TSSI idle estimation and restored afterwards. Reviewed-by:
Pieter-Paul Giesberts <pieterpg@broadcom.com> Tested-by:
David Herrmann <dh.herrmann@gmail.com> Signed-off-by:
Arend van Spriel <arend@broadcom.com> Signed-off-by:
John W. Linville <linville@tuxdriver.com>
-
Arend van Spriel authored
The gain level control for the test tone has been changed. This calbration test tone is used to determine the i/q compensation. The i/q calibration routine has been reworked to accomodate this. Cc: Jonas Gorski <jogo@openwrt.org> Tested-by:
Hante Meuleman <meuleman@broadcom.com> Signed-off-by:
-
Arend van Spriel authored
Update the transmit gain table for bcm4313 chip family. Tested-by:
-
Arend van Spriel authored
For debug purposes it is good to have the phy and radio information available in the log. Only logged when driver is built when BRCMDBG or BRCM_TRACING kconfig are set. Tested-by:
-
Arend van Spriel authored
This patch converts all sizeof(x)/sizeof(x[0]) instances to ARRAY_SIZE macro in phytbl_lcn.c. The patch was made using spatch with ARRAY_SIZE.cocci (see [1]). [1] https://github.com/coccinelle/coccinelle/tree/master/demos/janitorings Cc: Jonas Gorski <jogo@openwrt.org> Tested-by:
-
Arend van Spriel authored
The function wlc_lcnphy_load_tx_gain_table() has a target PA gain specified for the iPA variant of the bcm4313. This gain value is reduced to avoid PA distortion. The if-statement is removed because it was rather redundant in the first place. Please note that this patch does not provide full iPA support. Cc: Jonas Gorski <jogo@openwrt.org> Tested-by:
-
Arend van Spriel authored
Cleaning up some code fragments reducing indentation and uncluttering some lines. Apart from whitespace there are no actual code changes made. Cc: Jonas Gorski <jogo@openwrt.org> Tested-by:
-
Sujith Manoharan authored
This is a AR9485/WB225 based card. Signed-off-by:
Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by:
-
Bing Zhao authored
Bug 60747 - 1286:2044 [Microsoft Surface Pro] Marvell 88W8797 wifi show 3 interface under network https://bugzilla.kernel.org/show_bug.cgi?id=60747 This issue was also reported previously by OLPC and some folks from the community. There are 3 network interfaces with different types being created when mwifiex driver is loaded: 1. mlan0 (infra. STA) 2. uap0 (AP) 3. p2p0 (P2P_CLIENT) The Network Manager attempts to use all 3 interfaces above without filtering the managed interface type. As the result, 3 identical interfaces are displayed under network manager. If user happens to click on an entry under which its interface is uap0 or p2p0, the association will fail. Work around it by removing the creation of AP and P2P interfaces at driver loading time. These interfaces can be added with 'iw' or other applications manually when they are needed. Signed-off-by:Bing Zhao <bzhao@marvell.com> Signed-off-by:
Avinash Patil <patila@marvell.com> Signed-off-by:
-
Sujith Manoharan authored
This improves RX diversity and performance for AR9485. Signed-off-by:
-
Sujith Manoharan authored
Signed-off-by:
-
Gabor Juhos authored
Along with other chipsets, the Ralink driver uses the frequency adjustment code for RF3053 as well. Remove the bogus place-holder comment from the RF3053 specific channel configuration function and call the frequency adjustment function instead Based on the DPO_RT5572_LinuxSTA_2.6.0.1_20120629 driver. Reference: RT3593_ChipSwitchChannel function in chips/rt3593.c Signed-off-by:
Gabor Juhos <juhosg@openwrt.org> Signed-off-by:
-
Gabor Juhos authored
Move the rt2800_adjust_freq_offset function before the channel configuration functions to make it usable from those without a forward declaration. The patch contains no functional changes. Signed-off-by:
-
Gabor Juhos authored
According to the DPO_RT5572_LinuxSTA_2.6.0.1_20120629 driver, the RFCSR17 register can't be programmed in one step on devices which are using the frequency offset adjustment code. Update the code to use step-by-step adjustment. Reference: RT30xxWriteRFRegister function in common/rt_rf.c Signed-off-by:
-
Gabor Juhos authored
According to the Ralink driver, there is an MCU command which can be used to send the frequency offset value directly to the USB device without going through the RFCSR writing sequence. Based on the DPO_RT5572_LinuxSTA_2.6.0.1_20120629 driver. Reference: RTMPAdjustFrequencyOffset function in common/rt_rf.c Signed-off-by:
-
Gabor Juhos authored
Don't write the new value into the register if it is the same as the old value to avoid unncessary USB bus traffic with USB devices. The change also saves a few cycle on MMIO based devices. Based on the DPO_RT5572_LinuxSTA_2.6.0.1_20120629 driver. Reference: RTMPAdjustFrequencyOffset function in common/rt_rf.c Signed-off-by:
-
Gabor Juhos authored
The current code in the 'rt2800_adjust_freq_offset' function limits the device specific frequency offset value to FREQ_BOUND but ignores the fact that the uppermost bit is not part of the frequency offset value. As the result, the driver always uses the FREQ_BOUND value if the uppermost bit is set. Update the code to use the correct source value for calculating the boundary. Based on the DPO_RT5572_LinuxSTA_2.6.0.1_20120629 driver. Reference: RTMPAdjustFrequencyOffset function in common/rt_rf.c Signed-off-by:
-
Gabor Juhos authored
Instead of precomputing the beacon base in each caller, pass the beacon index to the 'rt2800_clear_beacon_register' function and compute the beacon base in there. This allows to simplify the caller functions a bit. Signed-off-by:
-
Gabor Juhos authored
The name of the HW_BEACON_OFFSET macro is a bit confusing. It returns with one of the HW_BEACON_BASE* values, so rename the macro to HW_BEACON_BASE to reflect that. The patch contains no functional changes. Signed-off-by:
-
-
- Aug 21, 2013
-
-
Frédéric Dalleau authored
When initiating a transparent eSCO connection, make use of T2 settings at first try. T2 is the recommended settings from HFP 1.6 WideBand Speech. Upon connection failure, try T1 settings. When CVSD is requested and eSCO is supported, try to establish eSCO connection using S3 settings. If it fails, fallback in sequence to S2, S1, D1, D0 settings. To know which setting should be used, conn->attempt is used. It indicates the currently ongoing SCO connection attempt and can be used as the index for the fallback settings table. These setting and the fallback order are described in Bluetooth HFP 1.6 specification p. 101. Signed-off-by:
Frédéric Dalleau <frederic.dalleau@linux.intel.com> Signed-off-by:
Johan Hedberg <johan.hedberg@intel.com> Signed-off-by:
Gustavo Padovan <gustavo.padovan@collabora.co.uk>
-
Frédéric Dalleau authored
Synchronous Connection Complete event can return error "Connection Rejected due to Limited resources (0x10)". Handling this error is required for SCO connection fallback. This error happens when the server tried to accept the connection but failed to negotiate settings. This error code has been verified experimentally by sending a T2 request to a T1 only SCO listener. Client dump follows : < HCI Command (0x01|0x0028) plen 17 [hci0] 3.696064 Handle: 12 Transmit bandwidth: 8000 Receive bandwidth: 8000 Max latency: 13 Setting: 0x0003 Retransmission effort: Optimize for link quality (0x02) Packet type: 0x0380 > HCI Event (0x0f) plen 4 [hci0] 3.697034 Setup Synchronous Connection (0x01|0x0028) ncmd 1 Status: Success (0x00) > HCI Event (0x2c) plen 17 [hci0] 3.736059 Status: Connection Rejected due to Limited Resources (0x0d) Handle: 0 Address: xx:xx:xx:xx:xx:AB (OUI 70-F3-95) Link type: eSCO (0x02) Transmission interval: 0x0c Retransmission window: 0x06 RX packet length: 60 TX packet length: 60 Air mode: Transparent (0x03) Server dump follows : > HCI Event (0x04) plen 10 [hci0] 4.741513 Address: xx:xx:xx:xx:xx:D9 (OUI 20-68-9D) Class: 0x620100 Major class: Computer (desktop, notebook, PDA, organizers) Minor class: Uncategorized, code for device not assigned Networking (LAN, Ad hoc) Audio (Speaker, Microphone, Headset) Telephony (Cordless telephony, Modem, Headset) Link type: eSCO (0x02) < HCI Command (0x01|0x0029) plen 21 [hci0] 4.743269 Address: xx:xx:xx:xx:xx:D9 (OUI 20-68-9D) Transmit bandwidth: 8000 Receive bandwidth: 8000 Max latency: 13 Setting: 0x0003 Retransmission effort: Optimize for link quality (0x02) Packet type: 0x03c1 > HCI Event (0x0f) plen 4 [hci0] 4.745517 Accept Synchronous Connection (0x01|0x0029) ncmd 1 Status: Success (0x00) > HCI Event (0x2c) plen 17 [hci0] 4.749508 Status: Connection Rejected due to Limited Resources (0x0d) Handle: 0 Address: xx:xx:xx:xx:xx:D9 (OUI 20-68-9D) Link type: eSCO (0x02) Transmission interval: 0x0c Retransmission window: 0x06 RX packet length: 60 TX packet length: 60 Air mode: Transparent (0x03) Signed-off-by:Marcel Holtmann <marcel@holtmann.org> Signed-off-by:
-
Frédéric Dalleau authored
Older Bluetooth devices may not support Setup Synchronous Connection or SCO transparent data. This is indicated by the corresponding LMP feature bits. It is not possible to know if the adapter support these features before setting BT_VOICE option since the socket is not bound to an adapter. An adapter can also be added after the socket is created. The socket can be bound to an address before adapter is plugged in. Thus, on a such adapters, if user request BT_VOICE_TRANSPARENT, outgoing connections fail on connect() and returns -EOPNOTSUPP. Incoming connections do not fail. However, they should only be allowed depending on what was specified in Write_Voice_Settings command. EOPNOTSUPP is choosen because connect() system call is failing after selecting route but before any connection attempt. Signed-off-by:
-
Frédéric Dalleau authored
This patch defines constants and macro for transparent data LMP features. It refers to Bluetooth Core V4.0 specification, Part C, Chap 3.3 which defines LMP feature mask. Signed-off-by:
-
Frédéric Dalleau authored
In order to establish a transparent SCO connection, the correct settings must be specified in the Setup Synchronous Connection request. For that, a setting field is added to ACL connection data to set up the desired parameters. The patch also removes usage of hdev->voice_setting in CVSD connection and makes use of T2 parameters for transparent data. Signed-off-by:
-
Frédéric Dalleau authored
When an incoming eSCO connection is requested, check the selected voice setting and reply appropriately. Voice setting should have been negotiated previously. For example, in case of HFP, the codec is negotiated using AT commands on the RFCOMM channel. This patch only changes replies for socket with deferred setup enabled. Signed-off-by:
-
Frédéric Dalleau authored
This patch defines constants for SCO airmode from SCO voice setting. It refers to Bluetooth Core V4.0 specification, Part E, Chap 6.12 which describe SCO voice setting format. Signed-off-by:
-
Frédéric Dalleau authored
This patch extends the current Bluetooth socket options with BT_VOICE. This is intended to choose voice data type at runtime. It only applies to SCO sockets. Incoming connections shall be setup during deferred setup. Outgoing connections shall be setup before connect(). The desired setting is stored in the SCO socket info. This patch declares needed members, modifies getsockopt() and setsockopt(). Signed-off-by:
-
Frédéric Dalleau authored
From Bluetooth Core v4.0 specification, 7.1.8 Accept Connection Request Command "When accepting synchronous connection request, the Role parameter is not used and will be ignored by the BR/EDR Controller." Signed-off-by:
-
Frédéric Dalleau authored
hci_connect is a super function for connecting hci protocols. But the voice_setting parameter (introduced in subsequent patches) is only needed by SCO and security requirements are not needed for SCO channels. Thus, it makes sense to have a separate function for SCO. Signed-off-by:
-
Gianluca Anzolin authored
In rfcomm_tty_cleanup we purge the dlc->tx_queue which may contain socket buffers referencing the tty_port and thus preventing the tty_port destruction. Signed-off-by:
Gianluca Anzolin <gianluca@sottospazio.it> Reviewed-by:
Peter Hurley <peter@hurleysoftware.com> Signed-off-by:
-
Gianluca Anzolin authored
The tty_port can be released in two cases: when we get a HUP in the functions rfcomm_tty_hangup() and rfcomm_dev_state_change(). Or when the user releases the device in rfcomm_release_dev(). In these cases we set the flag RFCOMM_TTY_RELEASED so that no other function can get a reference to the tty_port. The use of !test_and_set_bit(RFCOMM_TTY_RELEASED) ensures that the 'initial' tty_port reference is only dropped once. The rfcomm_dev_del function is removed becase it isn't used anymore. Signed-off-by:
-
Gianluca Anzolin authored
Implement .activate, .shutdown and .carrier_raised methods of tty_port to manage the dlc, moving the code from rfcomm_tty_install() and rfcomm_tty_cleanup() functions. At the same time the tty .open()/.close() and .hangup() methods are changed to use the tty_port helpers that properly call the aforementioned tty_port methods. Signed-off-by:
-
Gianluca Anzolin authored
Move the tty_struct initialization from rfcomm_tty_open() to rfcomm_tty_install() and do the same for the cleanup moving the code from rfcomm_tty_close() to rfcomm_tty_cleanup(). Add also extra error handling in rfcomm_tty_install() because, unlike .open()/.close(), .cleanup() is not called if .install() fails. Signed-off-by:
-
Gianluca Anzolin authored
The current code removes the device from the device list in several places. Do it only in the destructor instead and in the error path of rfcomm_add_dev() if the device couldn't be initialized. Signed-off-by:
-
Gianluca Anzolin authored
In net/bluetooth/rfcomm/tty.c the struct tty_struct is used without taking references. This may lead to a use-after-free of the rfcomm tty. Fix this by taking references properly, using the tty_port_* helpers when possible. The raw assignments of dev->port.tty in rfcomm_tty_open/close are addressed in the later commit 'rfcomm: Implement .activate, .shutdown and .carrier_raised methods'. Signed-off-by:
-
Marcel Holtmann authored
In case of a Low Energy only controller it makes no sense to configure the full BR/EDR event mask. It will just enable events that can not be send anyway and there is no guarantee that such a controller will accept this value. Use event mask 0x90 0xe8 0x04 0x02 0x00 0x80 0x00 0x20 for LE-only controllers which enables the following events: Disconnection Complete Encryption Change Read Remote Version Information Complete Command Complete Command Status Hardware Error Number of Completed Packets Data Buffer Overflow Encryption Key Refresh Complete LE Meta This is according to Core Specification, Part E, Section 3. Signed-off-by: -
Johan Hedberg authored
When a socket is in deferred state there does actually exist an underlying connection even though the connection state is not yet BT_CONNECTED. In the deferred state it should therefore be allowed to get socket options that usually depend on a connection, such as SCO_OPTIONS and SCO_CONNINFO. This patch fixes the behavior of some user space code that behaves as follows without it: $ sudo tools/btiotest -i 00:1B:DC:xx:xx:xx -d -s accept=2 reject=-1 discon=-1 defer=1 sec=0 update_sec=0 prio=0 voice=0x0000 Listening for SCO connections bt_io_get(OPT_DEST): getsockopt(SCO_OPTIONS): Transport endpoint is not connected (107) Accepting connection Successfully connected to 60:D8:19:xx:xx:xx. handle=43, class=000000 The conditions that the patch updates the if-statements to is taken from similar code in l2cap_sock.c which correctly handles the deferred state. Signed-off-by:
-
Andy Shevchenko authored
There are two places where DIV_ROUND_UP may be used. It makes code a bit clearer. Signed-off-by:
Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by:
-
- Aug 17, 2013
-
-
