Devices supported by the driver which support EEE (currently 82579, I217
and I218) are advertising EEE capabilities during auto-negotiation even
when EEE has been disabled.  In addition to not acting as expected, this
also caused the EEE status reported by 'ethtool --show-eee' to be wrong
when two of these devices are connected back-to-back and EEE is disabled
on one.  In addition to fixing this issue, the ability for the user to
specify which speeds (100 or 1000 full-duplex) to advertise EEE support
has been added.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

When the MAC and PHY are in two different modes (different power levels
and interconnect speeds), it could take a long time before a PHY register
access timed out using the existing MAC-PHY interconnect configuration
coded into the driver for ICH- and PCH-based LOMs.  Introduce an I217/I218-
specific .setup_physical_interface operation which does not override the
interconnect configuration in the NVM.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

When the LEDs are driven by cathode, the bit logic is reversed.  Use the
LED Invert bit to invert the logic.  Cleanup use of a magic number and
change the for loop increment to reduce the number of shifts.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Two 82579 LOMs connected via a 10Mb hub experience extraordinarily low
performance.  This is because 82579 is excessively aggressive on transmit
at 10Mb half-duplex and will not provide sufficient time for the link
partner to transmit.  When the link partner is also 82579, the result is a
lot of collisions (and corresponding re-transmits) that cause the poor
performance. To work-around this issue, significantly increase the IPG in
the MAC to allow enough gap for the link partner to transmit and reduce the
Rx latency in the analog PHY to 0 to reduce the number of collisions.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

PHY reads/writes via the MDIC register could potentially return results
from a previous PHY register access.  If that happens, the offset in the
returned results will be that of the previous access and if that is
different from the expected offset, log a debug message and error out.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Move mutex initialization by allocation of the mailbox it protects.

introduced in commit 1d6f3cd8

 'bnx2x: Prevent VF race'

Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Tokenring support was deleted in v3.5. One last holdout of the macro
CONFIG_TR escaped that fate. Until now.

Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: David S. Miller <davem@davemloft.net>

The commit 40893fd0

(net: switch to use skb_probe_transport_header())
involes a new error accidently. When NET_SKBUFF_DATA_USES_OFFSE is
not enabled, below compile error happens:

  CC      net/packet/af_packet.o
  net/packet/af_packet.c: In function ‘packet_sendmsg_spkt’:
  net/packet/af_packet.c:1516:2: error: implicit declaration of function ‘skb_probe_transport_header’ [-Werror=implicit-function-declaration]
  cc1: some warnings being treated as errors
  make[2]: *** [net/packet/af_packet.o] Error 1
  make[1]: *** [net/packet] Error 2
  make: *** [net] Error 2

As it seems skb_probe_transport_header() is not related to
NET_SKBUFF_DATA_USES_OFFSE, we should move the definition of
skb_probe_transport_header() out of scope of
NET_SKBUFF_DATA_USES_OFFSE macro.

Cc: Jason Wang <jasowang@redhat.com>
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

yam_open has a redundant null check on null,  it will
never be called with dev == NULL. Remove this redundant check.
This also cleans up a smatch warning:

drivers/net/hamradio/yam.c:869 yam_open() warn: variable
  dereferenced before check 'dev' (see line 867)

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Conflicts:
	include/net/ipip.h

The changes made to ipip.h in 'net' were already included
in 'net-next' before that header was moved to another location.

Signed-off-by: David S. Miller <davem@davemloft.net>

Marc Kleine-Budde says:

===================
this is a pull-request for net-next/master. It consists of three
patches by Lars-Peter Clausen to clean up the mcp251x spi-can driver,
two patches from Ludovic Desroches to bring device tree support to the
at91_can driver and a patch by me to fix a sparse warning in the
blackfin driver.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

In case of fixed speed set up for a NIC (e.g. ethtool -s eth0 autoneg off speed
100 duplex full) with an ethernet cable plugged off, the mentioned algorithm
slows down a NIC speed, so further cable hook-up leads to nonoperable link state.

Signed-off-by: Kirill Kapranov <kapranoff@inbox.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>

Move the protection of netns_frags.nqueues updates under the LRU_lock,
instead of the write lock.  As they are located on the same cacheline,
and this is also needed when transitioning to use per hash bucket locking.

Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The LRU list is protected by its own lock, since commit 3ef0eb0d


(net: frag, move LRU list maintenance outside of rwlock), and
no-longer by a read_lock.

This makes it possible, to remove the inet_frag_queue, which is about
to be "evicted", from the LRU list head.  This avoids the problem, of
several CPUs grabbing the same frag queue.

Note, cannot remove the inet_frag_lru_del() call in fq_unlink()
called by inet_frag_kill(), because inet_frag_kill() is also used in
other situations.  Thus, we use list_del_init() to allow this
double list_del to work.

Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is a native function to dump hex buffers.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In kernel we have fast and pretty implementation of the isxdigit() function.
Let's use it.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make few alignments, comment fixes and debug messages.

Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add full support for "ethtool -m" command.

Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The mail box containing the Vf-Pf messages is susceptible
to a race - it's possible for 2 flows to try and write commands,
causing one to override the other's message.
Use a mutex to synchronize the access, preventing said race.

Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Outer vlan removal in VF queues was made according to the VF's
multi-function mode (which is never set).
Instead, the PF's multi-function mode should be used to determine
if outer vlan removal is needed.

Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

After a VF performs load/unload its statistics become corrupt -
we now zero the statistics structures upon a VF device load.

Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If ARI forwarding flag is missing from the PCI bridge, remove SR-IOV
support instead of failing the probe process.

Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 7fa6f340

 "AER revised" erroneously inserted an error-flow
in which a semaphore is released even though the attempt to take it
has failed.

Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Switch to use the new help skb_probe_transport_header() to do the l4 header
probing for untrusted sources. For packets with partial csum, the header should
already been set by skb_partial_csum_set().

Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Sometimes, we need probe and set the transport header for packets (e.g from
untrusted source). This patch introduces a new helper
skb_probe_transport_header() which tries to probe and set the l4 header through
skb_flow_dissect(), if not just set the transport header to the hint passed by
caller.

Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

For untrusted packets with partial checksum, we need to set the transport header
for precise packet length estimation. We can just let skb_pratial_csum_set() to
do this to avoid extra call to skb_flow_dissect() and simplify the caller.

Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This fixes a number of sparse warnings like:
  warning: incorrect type in argument 2 (different address spaces)
    expected void volatile [noderef] <asn:2>*addr
    got unsigned int *<noident>

  warning: Using plain integer as NULL pointer

Additionally this fixes a warning from checkpatch.pl like:
  WARNING: sizeof pch_param.station should be sizeof(pch_param.station)

Signed-off-by: Sahara <keun-o.park@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull IOMMU fixes from Joerg Roedel:
 "Here are some fixes which have collected since Linux v3.9-rc1.

  The most important one fixes a long-standing regressen which make
  re-hotplugged devices unusable when AMD IOMMU is used.

  The other patches fix build issues (build regression on OMAP and a
  section mismatch).  One patch just removes a duplicate header include."

* tag 'iommu-fixes-v3.9-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
  iommu/amd: Make sure dma_ops are set for hotplug devices
  x86, io_apic: remove duplicated include from irq_remapping.c
  iommu: OMAP: build only on OMAP2+
  amd_iommu_init: remove __init from amd_iommu_erratum_746_workaround

Commit 06ae43f3

 ("Don't bother with redoing rw_verify_area() from
default_file_splice_from()") lost the checks to test existence of the
write/aio_write methods.  My apologies ;-/

Eventually, we want that in fs/splice.c side of things (no point
repeating it for every buffer, after all), but for now this is the
obvious minimal fix.

Reported-by: Dave Jones <davej@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This patch fixes the following sparse warning:

drivers/net/can/bfin_can.c:415:13: warning: symbol 'bfin_can_interrupt' was not declared. Should it be static?
drivers/net/can/bfin_can.c:507:19: warning: symbol 'alloc_bfin_candev' was not declared. Should it be static?

Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Use dev_pm_ops instead of the deprecated legacy suspend/resume callbacks.

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

By using module_spi_driver we can eliminate a few lines of boilerplate code.

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

In ancient times it was necessary to manually initialize the bus field of an
spi_driver to spi_bus_type. These days this is done in spi_driver_register() so
we can drop the manual assignment.

The patch was generated using the following coccinelle semantic patch:
// <smpl>
@@
identifier _driver;
@@
struct spi_driver _driver = {
	.driver = {
-		.bus = &spi_bus_type,
	},
};
// </smpl>

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

SAMA5D3 devices also embed CAN feature. Moreover if we want to produce a single
kernel image it is not useful to be too restrictive.

Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Add device tree support.

Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

There is a bug introduced with commit 27c2127a

 that causes
devices which are hot unplugged and then hot-replugged to
not have per-device dma_ops set. This causes these devices
to not function correctly. Fixed with this patch.

Cc: stable@vger.kernel.org
Reported-by: Andreas Degert <andreas.degert@googlemail.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>

Signed-off-by: Tony Cheneau <tony.cheneau@amnesiak.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

This formatting issue was introduced with commit
d4ac3236



Signed-off-by: Tony Cheneau <tony.cheneau@amnesiak.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The register names have been wrong since the beginning but it only showed up now
as they are actualy used for the upcoming auto ACK support.

Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Implement the filter function to update short address, pan id and ieee
address on change. Allowing for hardware address filtering needed for
auto ACK.

Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>